Develop Bugs

SetCPU and screen not turning on...

Now I am not blaming the app I am just wondering... everynow and then, when I wake my phone up, it doesn't want to wake up or when I turn it on and try to unlock it freezes... was wondering if anyone else was getting the same thing.
Rooted using the one-click method.
Screen off setting is min 400 max 400.
Sent from my SPH-D700 using XDA App

SetCPU issues
I have been having the same issues myself. Mine was set low to 100min/max: screen off just as a test today and it did that to me a on a few seperate occasions. Not sure why, just ended up battery pulling after 10-15 seconds of no response from the phone.

The cpu is set too low on screen off, go for 245 or so

setcpu does not play nice with r phones. i had problems witth it on every kernal i played with. right now im using the mix up kernal. i used setcpu to 1.2ghz max and 100mhz min. conservative governore. i have yet to find a set up to use while the screen is locked with no issues. what i do know is galaxy s phones only like the conservative setting. maybe a 400mhz max 100mhz min with conservastive governore would work?

Make sure setcpu is set to conservative. I set my lowest to 200mhz and max at 1200. No issues here other than sometimes the notification pull down bar is laggy but it does that stock anyway.
Sent from my SPH-D700 using Tapatalk

I'll try out those settings tomorrow. Thanks guys =)

Any1 know how to get to 1.4 ghz? my max is 1.2 on setCPU and i have voodoo kernel flashed

Try this to hit 1.4.
http://forum.androidcentral.com/epic-4g-roms-hacks/36554-emergency-rom-alert-baked-snack-1-0-a.html

zetterwing said:
Try this to hit 1.4.
http://forum.androidcentral.com/epic-4g-roms-hacks/36554-emergency-rom-alert-baked-snack-1-0-a.html
Click to expand...
Click to collapse
thanx dude i really appreciate it but still only 1.2 for sum reason

II5StarII Swag said:
thanx dude i really appreciate it but still only 1.2 for sum reason
Click to expand...
Click to collapse
There's a kernal that allows you to hit 1.4ghz its the overclocked one from baked snacks
Sent from my SPH-D700 using XDA App

mysteryemotionz said:
There's a kernal that allows you to hit 1.4ghz its the overclocked one from baked snacks
Sent from my SPH-D700 using XDA App
Click to expand...
Click to collapse
thats the rom i switched from dude both only allowed up to 1.2ghz thanxs for replying

II5StarII Swag said:
thats the rom i switched from dude both only allowed up to 1.2ghz thanxs for replying
Click to expand...
Click to collapse
The rom don't control the cpu speeds. The kernal does. You cab run any rom kernal combo you would like. In order to hit the 1.4ghz you want you need to run a kernal that is capable of doing so
Sent from my SPH-D700 using XDA App

Is SetCPU really necessary anymore? If you run a kernel that's not locked into performance mode it will scale on it's own even without SetCPU. I haven't installed it on my Epic yet and when monitoring the phone with SystemPanel I see my CPU go down to 200mhz when idle and scale up when processes are running.

Where is the kernel for 1.4? I have baked snack rom max is 1.2 i know kernel is the part that "controlls" speed but I'm stuck. Any help
Sent from my SPH-D700 using XDA App

specialk0324 said:
Where is the kernel for 1.4? I have baked snack rom max is 1.2 i know kernel is the part that "controlls" speed but I'm stuck. Any help
Sent from my SPH-D700 using XDA App
Click to expand...
Click to collapse
Last I knew it was on the baked snacks website
Sent from my SPH-D700 using XDA App

Set cpu with stock kernel droid incredible

I just rooted my incredible and I'm using the kernel that came with it stock. I disabled perflock and I left the max speed to 998 and the min speed to 245.
When I'm not doing anything on my incredible, I see that the speed constantly changes from the max to the min. Not even one second passes before it just goes back and forth, back and forth. Is this normal?
Coming from the d1 where it would stay at the min when idle, I'm not sure if what's going on with my incredible is normal.
Sent from my ADR6300 using XDA App

Yes that's normal. For better battery life, I'd try a kernel with smartass governor. It spends more time on the lower frequencies.
Sent from my ADR6300 using Tapatalk

Switching to a different kernel will give you the ability to overlook//underfoot the system needed.. this in turn increases battery life.. kingklick, ziggy's, chad's kernel are all well known kernels.. you will want to play with different kernels.. not every kernel will be stable to overlook to certain speeds on certain Rom's.. switching kernels is almost as addictive as switching roms.. always nandroid before flashing anything..
Sent from my ADR6300 using XDA App

Typos on my end.. underfoot = undervolt.. overlook = overlook.
Sent from my ADR6300 using XDA App

Will those kernels work on my rooted stock incredible?
Sent from my ADR6300 using XDA App

Yea! By stock i'm assuming all you did was root. I am currently running SkyRaider 3.5 Sense along with
"2.6.32.26-ubcredujuerbek-12082010 [email protected] #11"
I will edit with links to these two items.
SkyRaider 3.5 Sense - SkyRaider
Chad's Kernel - Incredikernel
My phone runs amazingly fast with sense but yet, even with heavy usage (Texting constantly, on the internet, gmail, even Fring) I can go an easy 24 hours on one charge. If my phone stays screen-off idle I could last at 95%-100% for several hours.

Yes, all I did was root.
Does the chad kernel provide wireless tether and will i still need to disable perflock in setcpu?
Sent from my ADR6300 using XDA App

the non stock kernels all disable perflock already, you do not need to do it..
flash the kernel via clockwork, and you are set.. jump into setcpu and adjust some settings and add profiles.. you'll be golden..

What he said ^^
Sent from my ADR6300 using XDA App

20twins10 said:
the non stock kernels all disable perflock already, you do not need to do it..
flash the kernel via clockwork, and you are set.. jump into setcpu and adjust some settings and add profiles.. you'll be golden..
Click to expand...
Click to collapse
Not quite. I believe Lou's has some tweaks within perflock, so disabling it would lose those.
And most kernel devs, particularly Lou and the ones who use HAVS, advise against using SetCPU. I'd check with your chosen kernel thread for details.
Sent from my ADR6300 using Tapatalk

Also, I wouldn't 'set on boot', at least till you find frequencies that your phone can handle safely. Otherwise, you'll get a 'crash' loop, where your phone starts up just fine, but once you go past the initial lockscreen it'll crash and reboot. Very annoying...
Sent from my Incredible using XDA App

what rager said... ive put on kernels and ran em high only to get a "boot loop".. its tuff to get out of cause you need to get back into setcpu to scale back otherwise it keep on going.... i learned to put the setcpu app icon on my main screen so i can get there fast to scale back..

http://forum.xda-developers.com/showthread.php?t=866736 can you install these with the stock rom. i wanted to experiment to get better battery life but didnt really want to install a different one.

keith4321 said:
http://forum.xda-developers.com/showthread.php?t=866736 can you install these with the stock rom. i wanted to experiment to get better battery life but didnt really want to install a different one.
Click to expand...
Click to collapse
Some. Make sure it's a sense version if you're using stock sense.
Sent from my ADR6300 using Tapatalk

Mr. Rager said:
Also, I wouldn't 'set on boot', at least till you find frequencies that your phone can handle safely. Otherwise, you'll get a 'crash' loop, where your phone starts up just fine, but once you go past the initial lockscreen it'll crash and reboot. Very annoying...
Sent from my Incredible using XDA App
Click to expand...
Click to collapse
That exact thing happened to me...pissed me off like crazy at first I was clueless then I just did a restore
Sent from my ADR6300 using XDA App

Yeah, if you let it boot loop too long it'll hard boot, which is where the phone cuts off completely. That has happened to me, and it ruins apps.
Sent from my Incredible using XDA App

Locking thread till further notice [blahbl4hblah]

Kernels will be on kernel manager

Changelog 1.0:
- Enabled swap support
- Enabled compcache support
- Added smartass governor
- Added scary governor
- Added batterysave governor [basically conservative]
- Disabled sleeper
- Removed userspace governor

reserved for later

download now To test on sense 3.0 .

stian230 said:
download now To test on sense 3.0 .
Click to expand...
Click to collapse
Let me know how that works out
Remember what I said in OP. Might work or might not
Sent from my HTC Vision using Tapatalk

Flashing now. Will report back with results.

I assume this works with any nightly/stable cm7? Like it doesn't break the camera or wifi?
Sent from my HTC Vision using XDA App

0.0 said:
I assume this works with any nightly/stable cm7? Like it doesn't break the camera or wifi?
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
This kernel has NO issues.
Please read the OP. It states everything in there

blahbl4hblah said:
This kernel has NO issues.
Please read the OP. It states everything in there
Click to expand...
Click to collapse
ok thanks. i will test this out, and will see how it goes

Just flashed and my wifi broke. Is it be because of the radio am using? Using .30
Sent from my HTC Vision using XDA Premium App

It's pretty funny. Wifi shouldn't be broken period.
If there's a problem post a logcat

blahbl4hblah said:
It's pretty funny. Wifi shouldn't be broken period.
If there's a problem post a logcat
Click to expand...
Click to collapse
Lol alrighty. Aha just flashed again and it started working. Thanks for the kernel bro.
Sent from my HTC Vision using XDA Premium App

Ok, thinking about flashing this.
What is the min / max CPU freq of this kernel? I like to run my phone at 1ghz
Do I use SetCPU for this?

booted fine on sense 3.0 everything is going very fast, BUT lost the camera and some 3D graphics on the weather. This has happened every time I try a oc kernel on sense 3.0. regardless this is probably a good kernel .when I get tired of sense in a few days and flasher cm7 again I will test your kernel. Thx.

I just flashed your kernel, well, kind off. In cwm everything looks fine but after booting it looks like the kernel was not changed. No new governors or other changes :S

stian230 said:
booted fine on sense 3.0 everything is going very fast, BUT lost the camera and some 3D graphics on the weather. This has happened every time I try a oc kernel on sense 3.0. regardless this is probably a good kernel .when I get tired of sense in a few days and flasher cm7 again I will test your kernel. Thx.
Click to expand...
Click to collapse
Really? Only camera broke?
Sent from my HTC Vision using XDA Premium App

blahbl4hblah said:
It's pretty funny. Wifi shouldn't be broken period.
If there's a problem post a logcat
Click to expand...
Click to collapse
Users are mentioning same problems with eugene's kernel, so something is going wrong in combination with certain roms/radios

GiGi. said:
I just flashed your kernel, well, kind off. In cwm everything looks fine but after booting it looks like the kernel was not changed. No new governors or other changes :S
Click to expand...
Click to collapse
i tested it and same here, no new governors. I am on CM7, nightly #65 w/ the .30 radio. also wifi broke for me. under "wifi", it says "Error" and the checkbox wont check (wifi wont turn on). i flashed multiple times and wiped dalvik-cache, but nothing worked
EDIT: disregard above post about the wifi. downgraded radio as lainvalenajr has mentioned, and now it works fine. but the issue of still having no new governors is still present

GiGi. said:
Users are mentioning same problems with eugene's kernel, so something is going wrong in combination with certain roms/radios
Click to expand...
Click to collapse
Had to Downgraded radio
Sent from my HTC Vision using XDA Premium App

GiGi. said:
I just flashed your kernel, well, kind off. In cwm everything looks fine but after booting it looks like the kernel was not changed. No new governors or other changes :S
Click to expand...
Click to collapse
Ditto. I'll probably downgrade the radio as mentioned and try to reflash.

Governors Resetting

Hey guys, I'm running Virtuous Unity 2.39 and I flashed Dres' 21 Kernel (forgive me, I probably just completely botched his name). The problem is, on Rom Toolbox, everytime I switch the governor to smartassv2 and clock it to 1209 MHz, it never stays, even with apply on boot checked. It always reverts back to 1152 MHz and ondemand. Any help?

I believe that is the way it is set up b/c it uses an oc daemon that only stops when using an app that is used specifically for oc or oc/uv such as setcpu if you take a look at the virtuous site it should have more info.
Sent from my ADR6350 using Tapatalk 2 Beta-5

dreamkiller80 said:
I believe that is the way it is set up b/c it uses an oc daemon that only stops when using an app that is used specifically for oc or oc/uv such as setcpu if you take a look at the virtuous site it should have more info.
Sent from my ADR6350 using Tapatalk 2 Beta-5
Click to expand...
Click to collapse
This is true, there's a conflict between Virtuous' OC Daemon and any app that manually adjusts kernel/CPU settings.
I think that if you install one of these though, the OC Daemon is immediately disabled. I have the same issue with ROM Toolbox on my i717 Note, but that's because we don't have a custom kernel as yet

[Q] No undervolt options in voltage control/setcpu

I'm currently using the myOneV RC 6.0fx+ rom and the kiss kernel on my primou but there seems to be no option for it in any of the apps I used. Is there something wrong I did because this kernel definitely supports UV if I'm not mistaken.
Any help is surely appreciated

Use Incredicontrol from the market it's free and gives you the option to UV.

Oh, I will try and use that later, but shouldn't setcpu and voltage control already provide the options?

nachos011 said:
Oh, I will try and use that later, but shouldn't setcpu and voltage control already provide the options?
Click to expand...
Click to collapse
most apps have this only in the paid version
so just use Incredicontrol

or there is a new app knows as daemon controller, m testing it currently

cybervibin said:
or there is a new app knows as daemon controller, m testing it currently
Click to expand...
Click to collapse
That's an old app that I like most. Been using it since Htc Desire time till now for my One V OC & UV purpose.

ckpv5 said:
That's an old app that I like most. Been using it since Htc Desire time till now for my One V OC & UV purpose.
Click to expand...
Click to collapse
Yea I just cane to know about it
Say it says daemon not installed any idea what that means
Sent from my One V

cybervibin said:
Yea I just cane to know about it
Say it says daemon not installed any idea what that means
Sent from my One V
Click to expand...
Click to collapse
Check whether you have the daemon (andrev_oc) in system/xbin.
If there is, means that your OC is CPUFreq instead of OCD.

Been using incredicontrol. It works great! Thanks so much guys

Use thanks button
Sent from my One V