No 4g on g2 - G2 and Desire Z Q&A, Help & Troubleshooting

Hello all! I installed unity on my g2 and since then I haven't seen 4g at all. Any ideas? Also, I asked this a few days back but I still can't run WiFi without mobile network shutting down. Any help on either subject would be greatly appreciated!
Sent from my HTC Vision using XDA App

*You should read the first few posts in the unity thread. It mentions that tmo lies about 4G and your phone will only show 4G when you really are in the area.
As for the actual 4G icon, it's been replaced with the H icon. Search the unity thread for the 4g icon mod. *
scratch that. it's gone since the last time the op was taken down. but yeah, it only shows 4g when you're actually in a 4G area. The mention of that is not in the thread anymore unfortuantely...
Final Edit: here's the official statement on that: http://www.virtuousrom.com/p/faq.html (it's the 2nd to last question on the bottom)
Your mobile netwok is disabled when you have wifi. It is normal. It prevents excessive battery drain. You'll be reconnected to your network as soon as you leave the wifi zone.
Sent from my Desire Z via XDA App

Thank you for your fast reply! I know that about the H icon, but in places i used to get it, i dont anymore. Maybe something is screwy because i just ran a speed test and it pulled 3.7 meg wit 2 bars 3g. I also understand about the wifi but for some reason i cant get calls or texts and i have to reboot to get the mobile network tgo come back on.
Sent from my HTC Vision using XDA App

coachmoore said:
Hello all! I installed unity on my g2 and since then I haven't seen 4g at all. Any ideas? Also, I asked this a few days back but I still can't run WiFi without mobile network shutting down. Any help on either subject would be greatly appreciated!
Click to expand...
Click to collapse
the "H" icon is "4G". If you want the "4G" icon, you can put it in the ROM yourself. You'll only see "H"/"4G" in the areas where the towers have been upgraded to HSPA (which is most major places by now, actually).
When you're connected to wifi, the phone automatically disables your 3G in order to save battery. It switches to "2G only" because your WiFi data is faster.

coachmoore said:
Thank you for your fast reply! I know that about the H icon, but in places i used to get it, i dont anymore. Maybe something is screwy because i just ran a speed test and it pulled 3.7 meg wit 2 bars 3g. I also understand about the wifi but for some reason i cant get calls or texts and i have to reboot to get the mobile network tgo come back on.
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
check the link in my signature of virtuous unity mods for the 4g icon.zip

coachmoore said:
Thank you for your fast reply! I know that about the H icon, but in places i used to get it, i dont anymore. Maybe something is screwy because i just ran a speed test and it pulled 3.7 meg wit 2 bars 3g. I also understand about the wifi but for some reason i cant get calls or texts and i have to reboot to get the mobile network tgo come back on.
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
i'm going to assume that this is the first time you installed unity on it. so yeah, what you thought you had 4g, actually was 3G. the unity rom actually denotes a difference in that and tells you that it's actually 3G not 4G.

Ok man, thank you again for all of your helpful replies. However the "H" icon i used to get all over the place, now i never see it. So what youre saying is that i was never really getting 4g, it just had the H up there. What i understood was gthe H was HSPA or 4g. As i said, i live close to atlanta, so i should have it, i thought i did anyway...lol
Sent from my HTC Vision using XDA App

coachmoore said:
Ok man, thank you again for all of your helpful replies. However the "H" icon i used to get all over the place, now i never see it. So what youre saying is that i was never really getting 4g, it just had the H up there. What i understood was gthe H was HSPA or 4g. As i said, i live close to atlanta, so i should have it, i thought i did anyway...lol
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
Don't worry too much about whether or not you see the "H" icon or the "3G" icon. A lot of times the "H" hangs up there much longer than it should. I noticed on some ROMs that it will just show "H" for a long time even though you've actually moved down to UMTS connection (3G).
As long as you're getting good speeds and not noticing a difference I wouldn't stress about it too much.

Ok, thanks for all of your help as always guys... You ate the best in the biz!
Sent from my HTC Vision using XDA App

lol np. just a quick search will usually solve you problems though
and to note, isn't ATL AT&T's hq? if so, then I dont think Tmo has much radio space there.

It is at&t, in fact, I'm a lineman for at&t. Tmobile is just cheaper and the service is a lot better.
Sent from my HTC Vision using XDA App

well, that's probably why. I'm on att, but i do hate their new "decisions" they've been making..but yeah, tmo probably has a little less power in that area thanks to it being AT&T's hq.

Related

Couple of things..

First, i would like to know if there is a way to keep the phone's data network ALWAYS on H not on 3G and having them switch back and forth it slows down the internet speed. Is there a setting or something i could change.
Second the notification LED. How can i make it so it can blink quicker.. i dont want to stare at my phone for like 5 seconds to see if its blinking or not...
Third the Swype keyboard ?? is it possible to get that keyboard after i put the Cyanmod ?? That keyboard is way better than the original android one.
I have a Rooted ( S- OFF) G2.
Cyan V6.1.0-RC3.
Thanks!
Fanatico said:
First, i would like to know if there is a way to keep the phone's data network ALWAYS on H not on 3G and having them switch back and forth it slows down the internet speed. Is there a setting or something i could change.
Click to expand...
Click to collapse
Your phone is only switching back to 3G if it loses the H signal. So that's an issue of your reception, not something your phone can control.
When i had the nexus one. It was always on 3G. Then i Rooted it. Changed radio etc etc.. and now it was 3g and switched to H like my g2 now. Before i hacked the G2 there was no 3g. It was either H or Edge. And everytime it's on 3G now that it's hacked it doesn't use it.. it simply just takes a few seconds then goes to H.
I use anycut from market.
New shortcut
Activity
Testing
Click on new shortcut
Select phone information
From there I scroll down to force the phone use wcdma.
I don't know if that'll work. You don't need root or anything.
I hope this helps
Sorry if it dont .
Sent from my T-Mobile G2 using XDA App
Fanatico said:
When i had the nexus one. It was always on 3G. Then i Rooted it. Changed radio etc etc.. and now it was 3g and switched to H like my g2 now. Before i hacked the G2 there was no 3g. It was either H or Edge. And everytime it's on 3G now that it's hacked it doesn't use it.. it simply just takes a few seconds then goes to H.
Click to expand...
Click to collapse
It was using 3G before, you just didn't know it. T-Mobile decided that they were going to have their G2's display H for HSPA+ as well as 3G to give people the illusion of almost always using pseudo-4G
ibemad1 said:
It was using 3G before, you just didn't know it. T-Mobile decided that they were going to have their G2's display H for HSPA+ as well as 3G to give people the illusion of almost always using pseudo-4G
Click to expand...
Click to collapse
The thing is that.. when i do a speed test and my phone is in 3g the speed is around 160-250 kbs then while is testing it switches to HSPA and the speed goes to 2-3mbs.. before I hacked it it was on H. And both of the times I tested in the same place. I understand that tmobile would disguise it.. but its odd that the speed test would switch like that, which didn't happen before. Also 3g and Hspa are two different networks :/
But still thanks for the help.

Phone will only get 2G in 3G areas?

Hello. Does anyone else have this problem? Once I rooted my evolution it only picks up 2g when it used to get 3g in these same areas. Is this normal? Thank you all for your help!
Sent from my PC36100 using XDA App
Did you change your Rom? How are you certain your only getting 2g?
If you chanced the rom, you might only be seeing the "1x" when you really used to have it displayed 3g. Is it sense or AOSP?
I've flashed the stock back on when I was wondering about a certain area, still 1x speeds, but showing 3g.
Hope that helps.
Sorry about the lack of info. Im running cm7 with firstblood theme and it displays 2g. Before this I had miui and it showed the 1x like you said earlier. The speeds are still pretty good though. Just wondering if this is normal. Thanks for the help!
Sent from my PC36100 using XDA App
As long as your speeds are the same as hey were before, or close, then I wouldnt worry about it. It could just be a glitch in the rom that is recognizing 3g as 2g.

[Q] WIMAX disconnects and never attempts to reconnect

I live in the suburbs of Houston where the WiMAX coverage is kind of spotty. If I leave an area of coverage for more than like say a minute, my 4G will stop attempting to scan for a new 4G signal and never attempt to reconnect even if I enter a new area with 4G coverage. I have to manually toggle the connection in the notification bar.
I've searched the forums and noticed several posts describing the same issue.
Does anyone have a solution?
AzN1337c0d3r said:
I live in the suburbs of Houston where the WiMAX coverage is kind of spotty. If I leave an area of coverage for more than like say a minute, my 4G will stop attempting to scan for a new 4G signal and never attempt to reconnect even if I enter a new area with 4G coverage. I have to manually toggle the connection in the notification bar.
I've searched the forums and noticed several posts describing the same issue.
Does anyone have a solution?
Click to expand...
Click to collapse
I have seen this issue as well, do you use bluetooth? I know its a random question but I have only noticed this issue with mine when I have the bluetooth on.
rayprobg said:
I have seen this issue as well, do you use bluetooth? I know its a random question but I have only noticed this issue with mine when I have the bluetooth on.
Click to expand...
Click to collapse
Bluetooth is not turned for on my device.
Bump. Anyone else having this issue?
I'm using the phone app so I don't know the link, but there's a link in general, I think, that describes increasing 4g performance. There's two simple tweaks to do and some involved ones. I just did the two simple ones. One is to change the retry interval down to 15 seconds and the minimum signal level for 4g lock is -110db. Those two changes made a noticeable improvement on fringe areas and inside for me.
forum.xda-developers.com/showthread.php?t=1265990
oscarthegrouch said:
forum.xda-developers.com/showthread.php?t=1265990
Click to expand...
Click to collapse
I did those tweaks, that is not the issue. I have tried all the WiMax_Scan_Retry from 1 to 300 and the WiMAX will never reconnect.
For example: I do not have 4G at school and I have 4G at home. If I drive to school, the 4G will disconnect.
Then when I drive home back into 4G coverage and go to sleep even after 10 hours, the 4G will not reconnect.
Bump!!! Also have this issue.
Sent from my SPH-D710 using XDA App
AzN1337c0d3r said:
I did those tweaks, that is not the issue. I have tried all the WiMax_Scan_Retry from 1 to 300 and the WiMAX will never reconnect.
For example: I do not have 4G at school and I have 4G at home. If I drive to school, the 4G will disconnect.
Then when I drive home back into 4G coverage and go to sleep even after 10 hours, the 4G will not reconnect.
Click to expand...
Click to collapse
Try doing what most people do, when you know your leaving a 4g area turn it off. Then turn it back on when you get home. No sense in wasting battery. That and it only takes a couple seconds to turn out back on and reconnect.
Sent from my SPH-D710 using Tapatalk
Khilbron said:
Try doing what most people do, when you know your leaving a 4g area turn it off. Then turn it back on when you get home. No sense in wasting battery. That and it only takes a couple seconds to turn out back on and reconnect.
Sent from my SPH-D710 using Tapatalk
Click to expand...
Click to collapse
I have extended battery that will literally last days even with 4G on so that is not an issue for me. Besides, this is not a viable solution if I want 4G in the car and it moves in and out of areas of spotty coverage. 3G where I live is about as fast as 1x.
Mod? Rooted? Modem?
Is your phone software on stock?
What OTA updates/mods are you running?
Kernel/Modem versions?
It would be good to know of the people seeing these problems have similar software/mods/modems.
mightypenguin said:
Is your phone software on stock?
What OTA updates/mods are you running?
Kernel/Modem versions?
It would be good to know of the people seeing these problems have similar software/mods/modems.
Click to expand...
Click to collapse
I agree. Post your setup in detail. It will help to narrow this issue down. For example I had similar prob's on EL13 modem but with 26/29 flash all is good.
So more info plz.
mightypenguin said:
Is your phone software on stock?
What OTA updates/mods are you running?
Kernel/Modem versions?
It would be good to know of the people seeing these problems have similar software/mods/modems.
Click to expand...
Click to collapse
I tried these:
Stock/Stock+Root/Starburst/Caulkin
EK02/EL26/EL29
Rogue1.3/1.4
This may be an example where adjusting the WiMax settings in ##data# with MSL number will help. Try lowering minimum signal picked up from -89 to -110, you can also change how long it stays connected and how fast it reconnects too...and here's where to read about it all...I did it on my OG Epic, Nexus, and this phone but slightly modified settings..it could also be a kernel thing too. Some of the Nexus ICS ones do that and wont reconnect until you go into settings and toggle
http://forum.xda-developers.com/showthread.php?t=925898
Sent from my SPH-D710 using xda premium
AzN1337c0d3r said:
I tried these:
Stock/Stock+Root/Starburst/Caulkin
EK02/EL26/EL29
Rogue1.3/1.4
Click to expand...
Click to collapse
Ok now it's time to go to your local sprint store. Im outa ideas. You have done morethan most B4 choking a rep.LoL.
I have this same problem.. Sometimes sitting in the living room. When im outside i get 4 bars of 4g but inside i get 1. if some reason i get disconected, it seems to switch over to 3g and stay there without scanning again. If i walk outside again, still stays 3g until i toggle off and on 4g again....
UNnamed with EL29 leaked modem flashed with Gunslinger kern.......
Sent from my SPH-D710 using XDA App
Anyone know of an app that will toggle 4g for us when it loses connection?
Or maybe a tasker profile? I tried in tasker, but I can't seem to get it to do more than basic things. There a couple spots in town that always lose 4g when I drive by and never reconnects as well. 3g is slower than when I use roam control on 1x verizon.

Where did my 4G go!

I live in area that does not have 4 g so it stays off, however today at airport I tried and no 4G toggle anywhere! Where did it go, I swore when I got s3 I tested 4G but now it's gone? Thanks for help.
Sent from my SPH-L710 using xda app-developers app
BiggieD said:
I live in area that does not have 4 g so it stays off, however today at airport I tried and no 4G toggle anywhere! Where did it go, I swore when I got s3 I tested 4G but now it's gone? Thanks for help.
Sent from my SPH-L710 using xda app-developers app
Click to expand...
Click to collapse
GS3 doent have a 4g "toggle" as you say...but you can make sure its enabled
settings-->more settings-->Mobile Network-->Network mode.
Preferred network mode should be set to "CDMA/LTE/EVDO"
If you have "CDMA/LTE/EVDO" enabled, anytime your in a Sprint LTE area your phone icon will switch from 3g to 4g.
n8te_1 said:
GS3 doent have a 4g "toggle" as you say...but you can make sure its enabled
settings-->more settings-->Mobile Network-->Network mode.
Preferred network mode should be set to "CDMA/LTE/EVDO"
If you have "CDMA/LTE/EVDO" enabled, anytime your in a Sprint LTE area your phone icon will switch from 3g to 4g.
Click to expand...
Click to collapse
doesn't it chew up more battery?
bigfamei said:
doesn't it chew up more battery?
Click to expand...
Click to collapse
it shouldnt chew up ure bttery at all, as all it does is search the network for 4gLTE and if it doesnt find it, it will automaticly go to sleep and try again like 2 or 3 hours later or periodically as it tells u. .however u do need to have sprint automatic connention left on in order for that work. atleast thats what i got from reading the sprint connection optimizer information it gave me.
Practitioner said:
it shouldnt chew up ure bttery at all, as all it does is search the network for 4gLTE and if it doesnt find it, it will automaticly go to sleep and try again like 2 or 3 hours later or periodically as it tells u. .however u do need to have sprint automatic connention left on in order for that work. atleast thats what i got from reading the sprint connection optimizer information it gave me.
Click to expand...
Click to collapse
The optimizer isn't for the LTE. I hate that garbage so I always leave it off. As long as your preferred network is set as stated above, it will automatically switch between them. Side note though, it may switch back to 3g if you don't have a very strong 4 g signal. It likes to be weird.
Sent from my SPH-L710 using xda app-developers app
Sounds like your thinking of a wimax phone. I I had a Motorola Photon and you had to physically turn 4g on and off on it.... I think most wimax 4g phones are that way.
Sent from my SPH-L710 using xda app-developers app
Do any of the custom ROMS have a toggle for 4g/3g? I live in a 4g area but sometimes the signal isn't strong enough so it goes to 3g. Quite annoying. It would be great to toggle 3g off and force 4g.
So I had s2 before s3, so I assume the s2 was a 4 -g wimax? It had a toggle widget.
Sent from my SPH-L710 using xda app-developers app
BiggieD said:
So I had s2 before s3, so I assume the s2 was a 4 -g wimax? It had a toggle widget.
Sent from my SPH-L710 using xda app-developers app
Click to expand...
Click to collapse
Correct !:good:
sssqueue said:
Do any of the custom ROMS have a toggle for 4g/3g? I live in a 4g area but sometimes the signal isn't strong enough so it goes to 3g. Quite annoying. It would be great to toggle 3g off and force 4g.
Click to expand...
Click to collapse
Have you tried updating to the new radio? I believe they boosted the power to give slightly better LTE connectivity in those kinds of environments.
There is a way to force LTE on the GS3. I did it with mine so that I could map out the LTE zones with sensorly a bit easier while I was driving over the weekend. The way I was able to do this is you need to have Nova Launcher downloaded and installed.
Once you do this, long press on the home screen and go to "Shortcuts".
Next click on "Activities"
Next scroll down to "IOTHiddenMenu"
Then scroll down and click on "IOTHiddenMenu : HDR1X_Selection"
Doing this will allow you to force LTE only mode. Keep in mind you WILL NOT be able to make any phone calls while doing this. For some reason the GS3 requires the phone to be in LTE + CDMA + EVDO Mode to make calls even if you have a very strong LTE signal.
Another app I would recommend downloading is called OpenSignalMaps. Once you have the LTE only mode turned on or even the normal LTE + CDMA mode, you can use this app to refresh your network by clicking the little refresh button at the bottom left of the app in the Overview tab. What this does is pretty much turn your phones mobile networks on and off and then scan for LTE first before scanning for EVDO. I have been able to connect to many more LTE sites by doing this. Even ones that are fairly far away.
Hope this all helps. Let me know if you have any extra questions.
No data connection at all
I have the settings on GSM/HSPA/LTE, but lost data connection completely. Tried to restart and turned on/off flight mode - still no data. Voice in and out is OK. I finally managed to reconnect by repeating the process. Is there a better way to reconnect?
Thanks.
Check out "Network"
https://play.google.com/store/apps/details?id=de.mangelow.network
It takes you to the network screen as well
Sent from my SPH-L710 using xda app-developers app
with the latest l13 radio my phone will not stay on 4g it is heavily biased to 3g and I do not know how to fix it. I am right next to the 4g towers.. ... any thoughts? Thanks
Thanks
Thanks. Unfortunately, the "Network" app would not run. So I followed a similar line, and found "3G Reconnect". It does not fix the connection issue. Any other thoughts?

Odd data problem

Ok so I have an unlocked LG Nitro HD with custom ROM (CM10) and it has a very weird problem. I've tried two different AT&T MVNO SIM cards (AirVoice and Consumer Cellular) both have the same issue. My data signal keeps changing from H to H+ and occasionally to 3G like every few seconds regardless of where I am using the phone even outside. I don't understand what the problem is. What could be the issue?
screwregi said:
Ok so I have an unlocked LG Nitro HD with custom ROM (CM10) and it has a very weird problem. I've tried two different AT&T MVNO SIM cards (AirVoice and Consumer Cellular) both have the same issue. My data signal keeps changing from H to H+ and occasionally to 3G like every few seconds regardless of where I am using the phone even outside. I don't understand what the problem is. What could be the issue?
Click to expand...
Click to collapse
Are you able to use mobile data or are you just wondering why the icons go back and forth?
lordcheeto03 said:
Are you able to use mobile data or are you just wondering why the icons go back and forth?
Click to expand...
Click to collapse
Data does work but it seems to drain the battery with the networks constantly switching and on occasion I get a "No Connection" screen on certain apps, I guess because if I open an app while its swapping networks the app cant connect. It's strange.
screwregi said:
Data does work but it seems to drain the battery with the networks constantly switching and on occasion I get a "No Connection" screen on certain apps, I guess because if I open an app while its swapping networks the app cant connect. It's strange.
Click to expand...
Click to collapse
Yeah, constantly swapping networks will drain the battery.. what about your APN settings?
lordcheeto03 said:
Yeah, constantly swapping networks will drain the battery.. what about your APN settings?
Click to expand...
Click to collapse
They are set up properly.
I had another odd problem, just a few minutes ago was texting someone and all of a sudden phone froze while vibrating then restarted! Don't know if that's a bug in CM10 or what, maybe the network swapping is as well.
screwregi said:
They are set up properly.
I had another odd problem, just a few minutes ago was texting someone and all of a sudden phone froze while vibrating then restarted! Don't know if that's a bug in CM10 or what, maybe the network swapping is as well.
Click to expand...
Click to collapse
Maybe make a backup of your CM10 and try flashing a different ROM not based on CM10.
screwregi said:
They are set up properly.
I had another odd problem, just a few minutes ago was texting someone and all of a sudden phone froze while vibrating then restarted! Don't know if that's a bug in CM10 or what, maybe the network swapping is as well.
Click to expand...
Click to collapse
I think this is the same issue that I recently fixed in quattrimus. I will try to get the fix included in the cm kernel soon. You might try my Rom to see if the fix works.
lordcheeto03 said:
Maybe make a backup of your CM10 and try flashing a different ROM not based on CM10.
Click to expand...
Click to collapse
I tried installing CM9 and it appears to have fixed the problem, the phone doesn't try to connect to the H+ network anymore, only the H network and seems to stay on it so far. I did see it quickly go over to the 3G network but it doesn't appear to be causing any issues, it went right back to the H network. However, I really wish the CM10 ROM worked right, as CM9 is so old...
screwregi said:
I tried installing CM9 and it appears to have fixed the problem, the phone doesn't try to connect to the H+ network anymore, only the H network and seems to stay on it so far. I did see it quickly go over to the 3G network but it doesn't appear to be causing any issues, it went right back to the H network. However, I really wish the CM10 ROM worked right, as CM9 is so old...
Click to expand...
Click to collapse
CM10 is snappy and oh so buttery smooth, I give you that. On another note, did you try any other CM10 variants? I'd give tdmcode's AOKP a spin. He says he might have fixed that problem you were talking about in his build.
lordcheeto03 said:
CM10 is snappy and oh so buttery smooth, I give you that. On another note, did you try any other CM10 variants? I'd give tdmcode's AOKP a spin. He says he might have fixed that problem you were talking about in his build.
Click to expand...
Click to collapse
I downloaded the CM10 ROM. It seems to behave slightly differently. It stays on H normally, but when I start to do something with data, it will go to H+ until the data loads, then go back to H. So far no disconnects, I'll keep you posted. Right now I have very limited data, I'm switching to T-Mobile as soon as UPS decides to deliver my SIM card (just found out they have a 1900MHz HSPA+ network in my area!) I'll be able to test it better then, but for now I'm trying to stick to wifi, especially since I wasted so much data tonight playing around with this stuff, lol.
screwregi said:
It stays on H normally, but when I start to do something with data, it will go to H+ until the data loads, then go back to H.
Click to expand...
Click to collapse
This is how it's supposed to work.
drumist said:
This is how it's supposed to work.
Click to expand...
Click to collapse
Ditto... H and 3g are subsets of each other. Namely they can handle simultaneous voice and data 4G (h+) and lte can only handle data. So it switches back to H so you can receive and make calls plus it uses less battery. If you are on either 4G techs and receive a phone call while downloading it will automatically switch to H from h+ or lte, this is why. The only way you will never see this is on an AT&T rom where it only has 4G and lte icons.
Sent from my LG-P930 using xda app-developers app
Swetnes said:
Ditto... H and 3g are subsets of each other. Namely they can handle simultaneous voice and data 4G (h+) and lte can only handle data. So it switches back to H so you can receive and make calls plus it uses less battery. If you are on either 4G techs and receive a phone call while downloading it will automatically switch to H from h+ or lte, this is why. The only way you will never see this is on an AT&T rom where it only has 4G and lte icons.
Sent from my LG-P930 using xda app-developers app
Click to expand...
Click to collapse
I have LTE disabled, I'm not using the phone on AT&T.
Swetnes said:
Ditto... H and 3g are subsets of each other. Namely they can handle simultaneous voice and data 4G (h+) and lte can only handle data. So it switches back to H so you can receive and make calls plus it uses less battery. If you are on either 4G techs and receive a phone call while downloading it will automatically switch to H from h+ or lte, this is why. The only way you will never see this is on an AT&T rom where it only has 4G and lte icons.
Sent from my LG-P930 using xda app-developers app
Click to expand...
Click to collapse
H+ isn't a subset of 4G is it? I know that the CM's have separate icons for 3G/H, H+, 4G, and LTE.
lordcheeto03 said:
H+ isn't a subset of 4G is it? I know that the CM's have separate icons for 3G/H, H+, 4G, and LTE.
Click to expand...
Click to collapse
That certainly is debatable but the US's largest carrier considers it to be, it behaves like 4g, H+ may not be as fast but it is 90%+ as fast in most markets small enough to not make a noticeable difference as far as people's perception and the technology behaves like LTE in a lot of respects, CM is international so it just conforms to International norms so that's why you get H+ AND 4G (LTE) designators.
Sent from my LG-P930 using xda app-developers app

Categories

Resources