Develop Bugs

WiFi Problems With 2 Networks

Hi
I have a wifi AP at home, and one at work, Both use WPA-PSK with mac addy auth. SSID Visible cause sh1te WM2003SE OS cant cope with hidden SSID.
Get a whole load of oddities from the XDA IIs. Both SSID's and keys are listed in the wifi setup on the device. What I would expect is that if I switch the device on when I am within range of the AP @ work, it connects to it no fuss, likewise, when I drive home, switch XDA on it connects, no fuss, unfortunately this is not usually the case. The following are in order of likelyness to occur!
Problem 1
Sometimes I switch it on, and it sits there searching for eons, never finds AP. If I disable and then re-enable wifi on the XDA then it connects.
Problem 2
Sometimes, the XDA will tell me that its connected to my home network when I am at work - it isn't!
Problem 3
Sometimes I switch it on, it connects to the AP, but no net connectivity - looking. Using PPC Ipconfig, I see that device never managed to get an IP addy. Stop, start wifi problem resolves
Problem 3
Occasionally, the PPC forgets the shared secret, and I have to re-input it, start/stop wifi before it will connect to the AP
Problem 4
Sometimes, it just BLUNTLY REFUSES to connect to the AP if I do the above. In this case I try all the above with a soft reset as well. If that fails then I need remove all the wifi AP's, soft reset, wait (ages) for it to see a new AP, enter the PSK then it will connect.
It also struggles to connect to other APs (wifi hotspots). Things work a whole lot better when there is just one AP involved (i,e not work and home).
Prob 4 occurs once/week, prob 1 occurs every day, others somewhere between. All problems are of course COMPLETELY UNACCEPTABLE for a product that has been released to the consumer.
Nigel

Hello Veledron,
I've a similar problem: at our company WLAN is set up to reqire WPA and authentication with user certificates. Since it is not possible to import user certificates in Windows Mobile 2003 SE "out of the box" I found out how to do that - it is described here
http://www.jacco2.dds.nl/networking/crtimprt.html
a little bit difficould procedure, but it worked - I can see my personal company certificate in the private-certificate store of my MDAIII.
The problem is, that I can't get a connection. WLAN-Manager says "connected", but I can't receive an IP-address - and in the logs of our Cisco-APs I can't see anything from my PDA. What also is a little bit strange for me: the MDAIII does not remember the setting "authentication with certificates", it always switches to "authentication using PEAP"...
any idea?
thanks
Gerald

Hi Veledron & gekap
I too have similiar problem with my netgear router at home. It seems that everytime it connect to the network it will just keep scanning eventhough it prompt that it already connected. It been 2 days and still i cannot manage to connect
Hopefully there is a solution to this problem.
Regardz
shark

There is.... Turn off AP, or move device to location where it is out of range, remove all WiFi profiles from device, hard reset, turn on router. wait (ages) for device to realize that there is a wifi ap nearby, enter PSK, all is well.
There seems to be no pattern to the WiFi failures, I have to do the above maybe twice a week to get it to connect. When the device gets itsself into a poor state this is the only way.
You cant delete an active profile, and the profile list only appears when wifi is turned on (stupid!) hence the need to turn off the AP.
Nigel

Hi Guys,
I manage to solve my wifi problem,
i just add the XDA IIs mac address to my netgear router plus assigned a reserve ip address based on it mac address and was able to connect successfully with no problem. Hope this solution helps.
Regardz
Sharkz

Hi,
thanks for the tips, but all of them are not a solution for me. I do not have any problems connecting to WLANs using WEP or to unencrypted WLANs, but i guess that there are problems with WPA in the PDA2K. I think the guys of you who have succussful connected to a WLAN using WPA have done that using WPA-PSK, not WPA with TKIP as encryption-method and PEAP or certificates as authentication method over 802.1x.
In our company TKIP is mandatory, and it is necessary to use certificates for authentication - this can be done with either EAP-TLS (so called "smartcard or certificate" in the setup-menu of the PDA-2k) or using PEAP. I've troubleshooted this a lot, and I can't see any authentication packet coming to our Cisco-APs from the PDA2K using this methods (I've turned on advanced logging on the APs to see any little bit...).
I fear the worst, that the WLAN-driver of the PDA2K does not support TKIP! Of course WPA is supportet from Windows 2003 Mobile SE, but in my opinion that is not enough - the card driver down the OS must also support the whole WPA-Standard, and it seems to me that the PDA2K driver does only support WPA-PSK. I found an article which can be an explanation of the problem:
http://www.socketforum.com/topic.asp?TOPIC_ID=2924
So I've 2 questions to you:
.) which driver version is installed on your PDA2Ks? (you can find that in the registry under HKLM\SOFTWARE\Drivers\Wavedev - I've: Common: 0.04.01, Device: 1.06.01 GER, DriverVersion: 0.08.00, Patch: 1.00)
.) has anyone of you ever connected to a WLAN using WPA (not WPA-PSK!)?
thanks
Gerald

XDA IIs Wifi and lockups

Does anyone have a problem with their wifi locking up their xda iis? I have bought a linksys router and am getting frequent lockups when using wifi. I am using the shipped O2 rom, thanks

I have no problem at all with Netgear router. Try changing the connection speed setting in the router to the "b" mode only. Hopefully this can solve your problem.

No problems here either I'm afraid. I'm using a Draytek Vigor 2600VG at home and at work there are two of us with XDA IIs using a Linksys BEFDSR41W wireless router and no problems there either.
Sorry! :-(
Try a hard reset (gulp!) and see if you still have problems (Without anything else installed that might be inteferring) otherwise might be a faulty unit perhaps.
--Neil

I second what xanth said, I had the problem where wifi would not turn on, so I hard reset and installed each software back individually the problem was Calligrapher 7.3 did not like being in Storage or Storage Card only in Main memory (go figure)

efjay said:
Does anyone have a problem with their wifi locking up their xda iis? I have bought a linksys router and am getting frequent lockups when using wifi. I am using the shipped O2 rom, thanks
Click to expand...
Click to collapse
I use the XDA IIs on a variety of wireless networks and experience problems with an alarming regularity. The most annoying is the fact that the top bar seems to loose functionality, when using wireless!!

I will actually add that I do seem to have problem with the "range" of WiFi.
I need to do more testing, but it doesn't seem to be more than 20m or so before have communication issues/timing out :-( Will have to find out what our walls are made of!!!

I have problems connecting sometimes. I regularly use three routers, Draytek, Buffalo and Belkin. The only time that it locks up is when using skype. The skype problem is a known issue with no cure.
Nigel

I am having a problem where my Siemens SX66 will loose connection to my Microsoft MN700 wireless AP on occasion. -It simply appears as if the Wifi radio shuts itself off.
Weird.....

Wifi has never worked for me. It simply doesn't work in the way nature intended.
The main problem (as far as I can tell) seems to be that it cannot get DNS or IP configuration settings from my router (Belkin 7630) automatically.
It can connect to my wireless network without any hassle, but that's about it. If I enter DNS and IP settings manually it works fine. But this is unworkable if you want to connect to another wireless network.
If I can't sort this out by next week I'm going to sell the unit on eBay. It's been nothing but a pain since I mistakenly bought it in December.
Wifi is a nightmare on this device! I'm going back to Nokia.

I am going to do a hard reset and test to see if i still get any freezes. Anyone know of any software i can use to backup my text messages?

WiFi
Hi guys,
Haven't had too many issues with WiFi over here - standard O2 Asia ROM (with the BT 3500 update).
I'm running a Netgear WG602 @ home with 64bit WEP and a Dlink AP2100 @ work with WPA-PSK. No connectivity problems at either location, both DHCP. It does however take a few minutes to connect, but this is on the odd occasion.
The only frustrating thing with the WiFi is that I have to soft-reset often to turn Wi-Fi on - any ideas? Hopefully O2 will fix this in the next ROM. Other than that, I've had the Nokia 9500, P900/800 and this is by far the best device for the power user.
Just me 2c!
Cheers
cK

Wifi is on all the time on my device, sometimes when I switch the device on while within range of an AP it does not connect. Often switching wifi off and then onn again causes it to connect. If this does not work then I can often go into the network dialogue section, and see the network marked as 'availble' but not connected (why it sometimes does not auto connect I dont know). Tapping connect usually cures. If that does not work then I too need to soft reset.
I hope like you that they fix this cause its damned anoying. I will be interested to see what the Benq P50 is like when its released. I shall get one from expansys to test and ship it back within the 7 days.
Nigel

As for those having problems with specific access points. It is not nessesarily the fault of the blue angel. It seems to me that none of the manufacturers of wireless kit understand the term 'standard' they all seem to have their own take on it, which is why kit from different manufacturers refuses to talk to each other. I am of the opinion that they do it in purpose to lock you into using their client cards with their AP's !!
Try it with some non Belkin kit and see what happens.
Nigel

Well i tried a hard reset and didnt install any apps and tried connecting to wifi again and still got a lockup and loss of connectivity. Im going to swap the router for another make and see what happens

Swapped my linksys router for a D-Link and so far no problems after 2 days. so looks like my problem was my router.

Swapped my linksys router for a D-Link and so far no problems after 2 days. so looks like my problem was my router.

XDA IIi and wifi
I just bought one of these and can't get it connected. I have a netgear wg602 access point. When I finally figured out how to set the IP manually (the 02 xda tech support said it can't be done - maybe they're right ;-)
I now have it saying it's connected, with right IP address. My DNS and gateway are set up for the wireless adapter in network adapters. The signal is average. The XDA says wifi is connected. The access point even says it's authenticated and associated - same as my other stations.
Only problem is, internet explorer doesn't find any web pages - says "The page you are looking for cannot be found" (works fine through GPRS)
Also, terminal services times out trying to connect to an internal IP address (to eliminate DNS as a problem)
So, anyone know how I troubleshoot network problems - it looks like a TCP/IP issue? Can't find ping or arp etc. I've also tried an IP address that I know works on the network.
thanks for any help
Dave

Hi
For ping, ipconfig and stuff, head to http://www.cam.com/windowsce.html
I have had multiple issues trying to get wifi working reliably. It still fails now, but there are a few tricks to get it working again. Most of my wifi issues have been due to regular use of three AP's [email protected] and [email protected] along with GPRS and VPN.
To start with I suggest setting all the ****e in connections (internet and home network to 'My ISP' then goto your wifi setup, network adapters, and tell it that the wireless card connects to the internet. Now, tap ok, and goto tools, network cards, tap the active connection (it must already be connected) and ensure that its set to internet.
Next soft reset the thing, and wait for it to connect to yr wifi. Now, use the ipconfig tool and ping tool from the above site to check that all is OK. Check that its got the default gateway right and a sensible LAN IP.
I have found on occasion that I can be connected via wifi, but that the device is still trying to talk using an old IP allocated by gprs which means nothing to my lan! IPconfig will show if all is OK.
Whoever wrote the whole of the networking system (and its terrible gui's) on windows mobile wants shooting. I usually have 2 VPN profiles setup under my work network. If I leave it set to that, and use wifi from my lan to connect to the internet all is fine. However if I try and access a local server, the damned thing starts trying to connect a vpn (it aint inteligent enough to work out that the IP I asked it to connect to is local).
I have been trying to find a setting for all this networking rubbish that allows me to do *everything* without reconfiguring each time - to no avail.
Another thing to note is that you cant send/receive MMS messages while wifi is connected (more stupidity), it tries to connect to the MMS server using the wifi connection, and the telco blocks it cause it wants to charge you for sending MMS over GPRS. Only solution is to disconnect wifi, send MMS then reconnect wifi!!!
Nigel

No problems with WiFi for me
Hmm I'm using an O2 Asia Rom as well.. and my wifi manager seems to automatically create "settings" for each AP it detects and I seem to have no problems connecting at all... been using WiFi around my house since the first day i got it..
i am using a Linksys Wireless 802.11b router..
btw I am new here.. finally able to register!
How's everybody doing?

Cannot turn off IEEE 802.1x
Has anyone had problems unchecking the 'IEEE 802.1x netwrok access control' checkbox???
I uncheck it, but then when I go back to the screen (click on the connection | then select 802.1x tab at the bottom) it has checked itself again!
The XDA IIs does not save the setting - it just keeps re checking itself 02 help have been no use - they sent me an instruction manual and it even says in one of the step 'uncheck IEEE check box'
Im am using a netgear wirelesss router and have also tried on a d-link
Sugestions - is anyone else having this problem??

WiFi issues?

I'm really satisfied about defy's performances but there's something i can't figure out with WiFi connection. I'm currently using a netgear wireless-N router which works flawlessy with all the other devices, my defy instead is not able to stay connected for more than 10 seconds, keeping disconnecting and re-connecting to the router, continuosly. No way to use the browser or the market under Wi-Fi.
I'm also on a motorola's forum, there i found other people who experienced the same issue. Some of them say the problem is related to wireless-N routers and yes, it looks like defy works better with wireless-G routers (tested).
Btw, no problem with the 3G.
I was wondering if some of you, here in xda, got trouble with defy's WiFi.

FWIW, I use my defy with my linksys wrt54gl router with no issues whatsoever, so it very well may be the wireless n being the issue.

I'm using an access point (netgear) with wireless N and i'm connected to Wifi all the time. I've had this mobile for a week so i haven't noticed myself getting disconnected on skype...but it works fine with N

I see a wifi issue with my fritz.box as well. wifi is (and stays) connected, but no data is going through. I've found various tips like using static ip or using different channels, but in the end they didn't work for me.
so I rooted the defy and modified the tiwlan.ini where ht_enable was set from 1 to 0, which actually disables N, but gives me a reliable connection instead.
hth

thanks for your replies.
@trosenda
Most of the times it keep disconnecting but sometimes it stays connected but there's no flow of data, that is what happened to you.
I will try your method, disabling N (ht_enable set to 0) probably forces defy to go through G only.
thanks

I have a netgear wifi g and I have some trouble with defy which keep on disconnecting so I can't use the browser or the market...It's not related with wifi n because my router is only g but the problems are there...If you found a solution can you post a step by step explanation?

Solved I figured out defy don't like wifi n routers and protected ones. With a router that broadcasts on g channels with no protection (btw only mac adress control access) the defy works like a charm...hope this help others

kibiwi said:
Solved I figured out defy don't like wifi n routers and protected ones. With a router that broadcasts on g channels with no protection (btw only mac adress control access) the defy works like a charm...hope this help others
Click to expand...
Click to collapse
Thanks.
Yes the problem is exactly what you said - defy doesn't like too much w-N and secured routers. Not all the people have this issue, however, it has been reported to Motorola through their forum. Let's wait for their answer, hopefully there could be a kind of fix.

I was having the same issue with my Belkin N (secured) in my house. But in two other buildings I have G routers w/o issues. So, I figured, just swap the N for a G, right? No. As soon as I tried either of the G routers in the house, same problem as with the N. So I put the Belkin back in the house and spent some time adjusting its three external antennae. Bingo! I now have as solid a connection with the N as with my two other G routers. Must have been interference. Phones? Applianaces? Sonos? BTW the only other thing I had with the same trouble was my PS3. Now, it's connected perfectly as well. Interference.

I'm online through my Linksys 610n router, haven't skipped a beat since I got the phone...
kibiwi said:
Solved I figured out defy don't like wifi n routers and protected ones. With a router that broadcasts on g channels with no protection (btw only mac adress control access) the defy works like a charm...hope this help others
Click to expand...
Click to collapse

Hey guys, just wanted to let you know that turning of the n-standard on my router, going to b/g mixed (from b/g/n) worked great, no more disconnections. Before, is disconnected like all 20 seconds or so.

What worked for me:
My router is a netgear dgn1000 (a/b/g/n), i had WiFi issues for long time, i tried with the G mode only, tried all the possible configurations (both on phone and router), but nothing to do, disconnections every 10 seconds still going on.
Finally i got it working by following these three steps:
1) Update the router firmware (my router was updated to 1.1.00.41)
Then from your dgn1000 configuration page - 192.168.0.1 -
2) Go to "Wireless settings", switch to G mode
3) Go to "LAN Setup" and assign an address reservation to your defy (e.g. 192.168.0.5)
Note: I tried 2) and 3) before the firmware was updated, no success. So, if you have a dgn1000, first of all update the firmware.
Hope this can help

I don't lise connection but the signal is very weak with Wifi. 3g réception is inside on the other hand
Sent from my MB525 using XDA App

xdaid said:
What worked for me:
My router is a netgear dgn1000 (a/b/g/n), i had WiFi issues for long time, i tried with the G mode only, tried all the possible configurations (both on phone and router), but nothing to do, disconnections every 10 seconds still going on.
Finally i got it working by following these three steps:
1) Update the router firmware (my router was updated to 1.1.00.41)
Then from your dgn1000 configuration page - 192.168.0.1 -
2) Go to "Wireless settings", switch to G mode
3) Go to "LAN Setup" and assign an address reservation to your defy (e.g. 192.168.0.5)
Note: I tried 2) and 3) before the firmware was updated, no success. So, if you have a dgn1000, first of all update the firmware.
Hope this can help
Click to expand...
Click to collapse
I had the DGN1000 with firmware 1.1.00.35 and my Milestone 2 was connecting very well. Now, I have a DGN1000 with the 1.1.00.28 and my Milestone 2 doesn't connect at all: every 10 secs the connection is re-established with a new dhcp request.
Do you think I ONLY have to change my firmware? Or I have to change also the address reservation?

hi,
why my DEFY wifi N only connect at 65mbit ???? why not 150mbit???
who knows something about it ???

Hmmmm don't know what to say I gotta netgear dng 2000 have no problem with connection just that the router was a lil weak. Fixed that with antenna replacements. Defy has the 2.2.2 Nordic deblur
Sent from my MB525 using XDA App

i am using TL-WR1043ND and its disconecting about once in minute
changed to wifi B/G nothing helps
FLS-BR how you maneged to get defy with 16GB is it froms SD card

[NEO] Strange wifi problem. Connects but no internet.

Hello. I have xperia neo for 1 week. It is great phone and great upgrade from my X8 but i see a strange wifi problem. My firmware is latest version - 4.0.A.2.368.
At my home phone connects fine to my wireless network and everything is stable. I do not see any disconnects, reboots or other problems. My router is linksys wrt320N and i connect at wireless N speed - 72Mbps.
When i try to connect to the wireless N network at my office the phone connects fine but i do not have internet access. I have IP assigned by the router, network is shown as connected but i do not have connectivity. I tried with 3 different browsers and with the market and nothing connects. At the same time i can connect with my laptop to the same network and i have internet. My colleagues with other phones also connect and have internet.
I tried setting static IP address on the phone but this did not help. I read that if i set static IP in router's settings assigned to the mac address of the phone this will help. Unfortunately i can not test this because i do not have access to router's settings. Also at my home i did not make such settings and everything is working fine.
Previously i have seen this problem with my X8 and the same work wifi network but it was not always present. It was present with some custom firmwares and not with others.
If you have any ideas or have seen this problem please help.

Having the same device from Globul I never had such problems for the 2 weeks I'm using it. I had some disconnects but i put the blame on my router.

if you can try changing the wifi channels

I think I've found the issue (by facing by myself)
The version neo is shippe (2.3.2) has a serious bug on AES encription.
Actually only the upgrade to 2.3.3 (no clue about upcoming 2.3.4) can fix the WPA/AES issue.
So the actual solutions are:
or change your wifi securty to WEP, updathe the phone via OTA
or use the Windows Software and update to 2.3.3.
Please note that if you use the Control Power widget it has been removed in 2.3.3

This was my problem when I had just bought my Arc.My phone couldn't surf the internet with my personal wifi network although I tried to use many browsers and also Android market. Then I reset and reinstalled my router, everything works well ^^

Ask your office IT staff to do a simple power cycle on the router and try connecting again. That may solve the problem.

[Q] my Arc has wifi problem ?

Hi everyone i just bought my arc yesterday and quite satisfied with the good quality of my phone call but today i experienced a problem is that my Arc can not compatible with the Planet WRT-415 Router .When i connect to this router the wifi icon appeared on my screen but i cannot browse to the webs ,access to the android market or do anything relate to the internet (but others router at coffee shops or public spots are ok) .I also have the iphone 4, the ipod touch and when i connect them to this Planet router everything work just fine. i assume that there is something wrong with my ARC .So could you please help me fix this problem,thank you very much
my ARC info : Model LT15i
Android version :2.3.4
Build number : 4.0.1.A.0.283

I think you need reconfigure your wireless router. you can search this case in Internet.

perhaps you can check the DHCP least time?
the lease that 'never expires' might be the problem:
http://forum.xda-developers.com/showpost.php?p=17737923&postcount=761

i have done alot of research but still can not figure it out, i also set the DHCP least time to 1 week but it doesnt work,i think it is not the hardware problem but something wrong with the firmware because yesterday i installed FXR WIFI FIX AND RESCUE and some others WIFI FIX APPS ,my device suddenly work about 1-2 hours normally then disconnected until today ,this error really make my upset,
the others device such as ,Hd2 iphone 4 and ipod touch gen1 and my laptop are ok with the wifi from this Planet Router.ony ARC has this problem

i have done : 1)reset wifi router
2) change the channel from 1 to 11
3) install WIFI FIX APPS including FXR WIFI FIX AND RESCUE
4) reset phone settings
but no helps ,
anyone can solved this problem please help me

is your router running in mixed mode? my router was running in bgn mixed mode and none of my android devices connect. when I switched the router to 802.11g only or 802.11n only, all of the android devices connect again.

No my router is only running as g mode because i bought it long time ago about nearly 5-6 years ago so it does not have n mode, my problem is that my arc does not totally incompartible with my router ,sometime it suddently work then i can browse the web and surf the internet with my arc then i try to reconnect it in order to check if it is fixed then it is disconnect again. I feel really upset with my phone ,sorry about my english

Not sure where shall I post my question. Can't find an answer but decided not to create a new post when a wi-fi problem one already exists.
I am trying to connect to WI-Fi in my office but it's WEP encrypted with password.
I got the password to connect to it and everything is working fine apart from internet use. I am connected to wi-fi but with local access only. Can't update email, browse the web or anything like it.
Is it because the Xperia Arc S does not support WEP encryption? Or because I'm doing something wrong?

Ratatox said:
Not sure where shall I post my question. Can't find an answer but decided not to create a new post when a wi-fi problem one already exists.
I am trying to connect to WI-Fi in my office but it's WEP encrypted with password.
I got the password to connect to it and everything is working fine apart from internet use. I am connected to wi-fi but with local access only. Can't update email, browse the web or anything like it.
Is it because the Xperia Arc S does not support WEP encryption? Or because I'm doing something wrong?
Click to expand...
Click to collapse
I do know that Android in general doesn't like WEP.

So in this case the only way to resolve the issue is to ask my company IT guy to change encryption, isnt it?
Are there any applications which could help with the problem or is it some kind of other issue and nothing can be done?

sdk16420 said:
I do know that Android in general doesn't like WEP.
Click to expand...
Click to collapse
I am using WEP here at home, with no problems at all. I use my Xperia Arc and have an HTC HD Mini running Android from the SD card, both connect via WEP flawlessly.
If you can only view 'local' pages only, it could be that your company use a Proxy Server to filter the webpages you can access while at work. It could also be that the settings for the DNS server are incorrect.
Depending how easily your IT department can be bribed... It may be worth stocking up on beers?

it is not web or wpa the problem is the phone,but sometime i dont know why my phone suddenly work with my PLANET modem, because i used to leave the ARC with wifi on all day at my home sometime it can connect to the internet just like normal.like zombie turn back to life .i found that when i hear the notification ring tone when i receive new gmail at my phone ,so when i hear that tone i know that my phone work with my wifi.when i try to disconnect and reconnect at that time,i cant access to the internet anymore

I have the same issue with my Arc and Neo, and now Tablet S. Seems to be an intrinsic problem of Android. For Arc and Neo, they both worked fine with firmware 2.3.2, and refused to work after upgrade to 2.3.3. Now a further upgrade to 2.3.4 does not help.
Any inspiration? I searched the max possible I could for a solution with the Almighty Google God and tried days after nights to set/reset router/phone/Tablet, and play with settings. No hope. Strange thing to notice:
1/ Can connect for a while, and then drop for no reason. AND, will reconnect after an unknown time ticks;
2/ Cannot have all three SE/S things wifi connecting together to the same router (Mine: Buffalo). Only one at a time. Yet my other NBs/IPad/IPod are still working flawlessly.
3/ All three can connect to certain make of routers: e.g., free wifi in airport/cafe.
So what exactly is happening?

hi guys after 2 weeks finally i found out a solution for my home wifi internet then my android phone now work like champ .so i hope that something im about to write here will help you:
(i have 1 modem adsl named Postef,1 Wifi Access point named Planet WRT415)
here are what i did :
1) change the IP address of Modem to :192.168.1.1
change the IP address of AP to 192.168.1.2
2) change the channel of AP to 9
At the first time my modem and AP have the same IP which is 192.168.1.1 so when i use iphone4 and laptop to browse 192.168.1.1 it logged in to the Modem but my Android phone logged in to the AP so that is the problem ,the android phone can not distinguish if you use the same IP for Modem and AP