HI EVERYONE
When i update my jasjar to win 6.5 that locked and now when i turn on or connect to USB,it's light off screen and show v1.01 on the bottom of screen and USB on top,i try to upadte my rom but i have error 101 but i check my device manager and i see microsoft USB sync (but device center not connected to my phone),JASJAR_ME_13082_171_10900_wwe_ship is my rom that i try to update.
i dont have any other rom.. please helpp me cuz i just know few information about Universal series..
Justphemy said:
HI EVERYONE
When i update my jasjar to win 6.5 that locked and now when i turn on or connect to USB,it's light off screen and show v1.01 on the bottom of screen and USB on top,i try to upadte my rom but i have error 101 but i check my device manager and i see microsoft USB sync (but device center not connected to my phone),JASJAR_ME_13082_171_10900_wwe_ship is my rom that i try to update.
i dont have any other rom.. please helpp me cuz i just know few information about Universal series..
Click to expand...
Click to collapse
if you get a 101 error when the rom update, then steps you have to do is remove SD card and reconnect usb necessarily continue with flash again
TUT to flash in Vista or W7, look at http://forum.xda-developers.com/showthread.php?t=313001
and for ROM WM 6.5 you can check at http://forum.xda-developers.com/showpost.php?p=8210942&postcount=4
fnx for help i got try it..
tnxxxx solvedddddd
Closed as solved
Related
hello,
i recently upgraded my ROM to T-mobile diamond release v1.1
I would like to upgrade to your special edition ROM since some things on the diamond release are not that good...
The problem is that anytime I try to install it the screen says "cannot find pocket pc, make sure your usb cable is connected" or something... it must be connected because active sync starts to run when i enter my pocket pc in his cradle, it also syncronises. I tried to reinstall te usb drivers, rebooted my pc, soft and hard reseted my pocket pc but I still get the same message... could somebody please explain to me what I'm doing wrong here?
thank you
MRJ
the SE rom is not new it's likely that you have one of the new roms which can only be downgraded by using the sd flash way insted of the usb flash way
also your icon say that you have a xda2 and the SE rom is only for xda1
I am trying to upgrade from Ivan's ROM beta 13 to beta 15... Using the MAupgrade utility... however, everytime the utility resets the device to start the ROM update i get "USB device not recognised" from my PC and the update fails to start... eventually i get a connection error message.
This used to work just fine... however, recently i installed Activesync 4.5 Beta 2. Could this be causing the problem...? otherwise i'm not sure what else might be causing this...
I have also tried running the tool in bootloader mode with and without "USB connections allowed" ticked in Activesync but with no success...
Can anyone help me please?
Trying to clear registry before upgrading ?
Have you tried to clear registry before upgrading?
Hi Kassel, thanks for your response.
I have done a hard reset prior to upgrading... wouldn't that clear the registry?
If not please let me know what else i can do that might help.
Also, it seems very strange that i can't seem to do the ROM upgrade from bootloader mode.
I think i might be having a problem with GetDeviceData as it seems to stay in the "checking the information on your device... please wait" for forever when i try to upgrade from bootloader mode.
If it does come up, then the panel which says which version is on my device and which version it will be replaced by is blank?
This is not the case if i try to do it through activesync (with the device set up as guest).
What might get in the way of reading the device data? I made sure it went from serial to USB when i plugged the USB cable into the device and i have tried different cables...
My bootloader appears to be V1.00
hmmm... any thoughts?
Same here...
I also have the same problem.
I installed ActiveSync 4.2
Alse after having installed AS, the MTTY program doesn't see the USB port anymore, just some COM ports.
Same to me too
I have ActiveSync 4.5 bata at work (Which couln't upgrade ROM)
while my notebook with ActiveSync 4.2 work fine
Wow, it's great to hear that people are having the same problem...
Is it possible to back track with Activesync? Is 4.1 still available?
If not, i think i still have an older version running at home (i hope!)...
Is this definitely the issue then?
l_pete_l said:
I have ActiveSync 4.5 bata at work (Which couln't upgrade ROM)
while my notebook with ActiveSync 4.2 work fine
Click to expand...
Click to collapse
I have ActiveSync 4.5 and upgrading my Jasjar was successfully done with the ROM Version: (1.90.96 / 1.13.00 / 42.47.P8)
Sorry for not knowing, but is that one of the AKU3.2 ROMs. Not sure if it should make a difference, but just curious.
Also, did you need to use the MAupgrade Utility?
Cheers,
What happens with the USB drivers after installing ActiveSync 4.2
The strange thing is, that I tried connecting my MDA Pro to a PC without ActiveSync on board.
USB ports were visible using MTTY
I installed ActiveSync 4.2 and only COM ports are visible in MTTY, the USB port has vanished.
Can this be caused by the USB driver that comes with the ActiveSync install ?
If I put my device in bootloader mode, it sais USB on the PDA screen, but the utility for the ROM upgrade doesn't see the PDA and comes up with a device not connected error.
I would really like to try out one of the new ROM's by Ivan or JwRight, but am unable to, because of these USB problems.
So please someone help !!!!!!!!
I have the same problem... if i put the device into bootloader mode, "serial" changes to "USB" but the PC comes up with "device not recognized"...
I have a Love (Arte300) device that doesn't want to start anymore,when I try to switch on it displays white screen with ipl1.36.0001,spl 1.36.0000,gsm 02.67.90,os 1.36.0.0 versions and it doesn't do anything else,it is impossible to connect to activesync it is possible to connect to the pc only in boot mode ,but when I try to use Artemis_uspl or artemis update rom it asys' error and doen't do it.Please any help for me?
Regards
i installed actisync to my wind vista then connected my universal an error apears on my pc says "the connected USB is not recognised"
having the same error on win xp sp2
any help plz :S:S
informations:
wm6
ROM version 2.02.02WWE
RADIO version 1.15.00
Protocol version 42.51.P8
ExROM version 2.03.07WWE
10x
3asfour said:
i installed actisync to my wind vista then connected my universal an error apears on my pc says "the connected USB is not recognised"
having the same error on win xp sp2
any help plz :S:S
informations:
wm6
ROM version 2.02.02WWE
RADIO version 1.15.00
Protocol version 42.51.P8
ExROM version 2.03.07WWE
10x
Click to expand...
Click to collapse
2 things:
1. Please READ the Wiki
2. In vista activesync is replaced for Windows Mobile Device center, uninstall activesync and replace with WMDC
Good luck,
i already installed windows mobile device center, i was trying what they said in wiki but stilll couldint connect:S
btw everytime i reset my universal im having a boot menu
one other prob when my battery goes to 85% the universal shut down
10x for ur reply orb3000
3asfour said:
i already installed windows mobile device center, i was trying what they said in wiki but stilll couldint connect:S
btw everytime i reset my universal im having a boot menu
one other prob when my battery goes to 85% the universal shut down
10x for ur reply orb3000
Click to expand...
Click to collapse
I would suggest try to flash another ROM, and perhaps replacing the battery could help
Good luck!
Sir, can i flash an other rom if i cannot connect my machin to my pc?
batery raplaced but still same prob cannot connect:S
3asfour said:
batery raplaced but still same prob cannot connect:S
Click to expand...
Click to collapse
try to move your USB connector on the Uni.
It sounds as though the port is damaged, if you move it slightly it may connect.
However if the port is damaged, I strongly suggest repairing it before trying to flash another rom. Replacement ports are not expensive and to replace the connector is an easy job.
Cheers,
Beasty
ill try that as soon as i find time to do it 10x for ur help
btw its charging normaly from the charger
3asfour said:
ill try that as soon as i find time to do it 10x for ur help
btw its charging normaly from the charger
Click to expand...
Click to collapse
Charging does not necesairly mean the data pins are aligned correctly.
The other option available is to enter bootloader mode, then plug the device in to the pc and see if the bootloader changes from saying serial to usb.
cheers,
Beasty
My Qtek 9000 just don't wanna turn on. When on USB, my computer says "can not find USB device"! But, when I click "power button" + "light button" + "reset button", on Qtek screen is "USB" on the top of the screen and "v2. 01" on the bottom, and computer finds "USB device".. Still, I don't know what to do and how to turn my Qtek on. Please help me. I need my phone!
Thanks..
Milos
Perhaps a hard reset could help
If not try to reflash a ROM
Instructions here:
http://wiki.xda-developers.com/index.php?pagename=Uni_ROM_Upgrade
Good luck,
Look, I CAN NOT turn my device on. I'm holdind the "power button" but NOTHING!
P.S. I need boot loader v2.01. Can you find it for me please?
I think that I need the corect ROM that I had before "this situation".. Can someone find me a ROM v2.01? Or tell me what to do!?
You are in bootloader mode with USB showing on the top and bootloader version on the bottom. Just connect to your computer and flash another ROM.
The numbers on the bottom are NOT version of the ROM, but a bootloader, just try different ROMs or try shipped ROM for your device, or better still READ WIKI.
enigma1nz said:
You are in bootloader mode with USB showing on the top and bootloader version on the bottom. Just connect to your computer and flash another ROM.
The numbers on the bottom are NOT version of the ROM, but a bootloader, just try different ROMs or try shipped ROM for your device, or better still READ WIKI.
Click to expand...
Click to collapse
Hey Enigma your 500th post LOL ...
and EMO_Raver as you said when you connect your device to computer there is usb onthe top and v2.01 in bottom so it means you have G4 device and you can flash a uni rom G4 one....see instruction in first post by Orb3000...
I was trying to flashi it, but even my PC finds Qtek as new device, when I want to chose "USB" in "port" menu (in mtty), there is only com1, com2 and com3! There is NO "USB", so I cannot flash it!
And when I just click on the "new ROM" icon that I dowonloaded here I always get: ERROR 101 - CONNECTION ERROR
Pleace Check:
1. Your device is properly connected to the USB cable or cradle (of corse it is, my PC founds it as new device)
2. Your USB cable or cradle is properly connected on PC (same as in first, cable is 100% connected)
3. Your device is turned on (it's in booter mode, USB on top and v2.01 on bottom)
So, what is the problem. Someone told me that my softwere died, so I need to "feed" my Qtek with new software, new ROM. Is that a problem? How to do it? HOW TO START MY PHONE AGAIN?
I need help! Asap!
...
what OS do you have on your pc ? windows XP ?
If Vista or Windows Seven u must change driver of Microsoft USB Device ...
ANd be carefull of baterry .. if u will discharged battery u will have big rpoblem ...
FIXED! Thanks everyone!