Good day fine sirs and ma'ams.
I would just like to say I love my Tilt 2, and have had it for a few months now with no real problems and this is about my 4th WM phone.
As of about a month ago, I have been unable to connect or sync the device to my PC.
I have WM Device center 6.1 (the latest from the website)
I am running windows 7
I had been able to sync the phone until about a month ago.
I have unchecked the box in the USB to PC for faster data synchronization.
Essentially, when I plug the phone into the computer, it just acts as if it is connected to a charger. Nothing comes up on the phone and nothing comes up on the computer. It just charges. I have even installed and uninstalled WMDC a couple of times.
I really am at my wits end here.
My question is, is there a fix for this apart from sending the phone in? I am able to flash the phone via the microsd card, and even tried going back to the e2 rom that is as close to the ATT rom as I could find.
I did find the stock rom, but it does not come with the image file, just the ruu.exe I believe. I cannot flash roms via the USB cable either, so I am only able to change things like I said, via the microsd card.
Any help is greatly appreciated! Thanks!
And yes, I have searched, and have found many other people posting in other threads saying they have the same problem, and everyone just says to uncheck that one box, which I have done, so that is NOT the problem.
Also, I would just like to add that when I go into the windows directory and attempt to run activesync (repllog.exe) I get the following message.
(cannot communicate with the pc because of the fllowing remote networking error (Error 608)
I have seen others ask help for this question without an answer on xda-dev also.
Thanks again! If anyone has the solution here I think a lot of people will be very happy!
:-(
turn off your firewall then pug ur device in and see if that works... works for me... perhaps your firewall started blocking it for some reason... other than that good luck
I had similar things happen to me in the past. While the phone is connected, check Windows Update whether there is a new version of Sync Center. This has fixed the problem for me.
i appreciate the suggestions.
However,
I have the firewall disabled and it still does not connect.
I uninstalled and reinstalled the WMDC using the latest software directly from the website. There appears to be no updates for the program once it is installed.
Any other suggestions?
Have you tried multiple USB cables, multiple USB ports, or even multiple computers? I've had USB cables which aren't capable of data transfer, as well as USB ports on the computer go bad. You might also considering a hard reset, to ensure no software on the phone could be causing the problem. If it's truly the USB port on the device that's broken, then you're in bad shape if you want to return it to AT&T for repair. You may be able to flash the AT&T stock ROM, but you won't be able to restore the AT&T stock SPL, which they check when fixing the device, so you may very well have to fork over some money to get it fixed. Best of luck
My phone is doing this also.
Multiple PC's, multiple USB ports, multiple cables. All of which worked perfectly beforehand...
The other thing to try is Internet Sharing - when I go in there and press 'connect', then it says Check USB cable connection, connect USB to any of my PC's/laptops and it doesn't register on the phone.
This phone is really a piece of ****. I could rant on for hours about the stupid problems there are with this handset, I'm sure I'm not alone. Perhaps I expected too much.
Anyway, if anyone has any info on how to make my USB connection work I'd love them forever...!
freakygeek said:
My phone is doing this also.
Multiple PC's, multiple USB ports, multiple cables. All of which worked perfectly beforehand...
The other thing to try is Internet Sharing - when I go in there and press 'connect', then it says Check USB cable connection, connect USB to any of my PC's/laptops and it doesn't register on the phone.
This phone is really a piece of ****. I could rant on for hours about the stupid problems there are with this handset, I'm sure I'm not alone. Perhaps I expected too much.
Anyway, if anyone has any info on how to make my USB connection work I'd love them forever...!
Click to expand...
Click to collapse
Could be a faulty device...my phone connects to every computer, every time. take the phone to your provider and show them whats happening.
Also, i've had issues with the standard mini USB ( http://www.meditronik.com.pl/doc/mini/usb-kabel-mini=foto=canon.jpg ) not properly connecting/loosing connection.
Try a HTC usb it might work better: http://bestcellbuy.com/bargainsea/Pictures/HTC/OEM_Home_Charger_USB_Cable/OEM_HTC_Data_Cable_07.jpg
I've tried the HTC USB lead that shipped with my phone to no avail.
I think the device is faulty (surprise surprise). It charges from USB perfectly fine, every time.
I'll post back once I find out what Telstra say... it's obviously still under warranty but that isn't really the issue - It is just such a major PITA having to switch to a loan phone and deleting confidential business data etc from my phone before sending away for repair etc etc...
Thanks for the help though, it is appreciated.
Well, I've got my USB going again. Not sure exactly what I've done, but basically I pulled the battery out for a few minutes and replaced it, turned on and off the 'high speed' checkbox in USB Connection Settings, and it has come good.
****box phone.
Somehow mine started working again last night too. Same cable, same port and everything.
Really odd, but I'm not complaining at the moment!
It seems this problem is spreading, as i'm being terrorized by this stupid bug... This afternoon I've tried to get internet on my laptop (by connecting my phone to it), but it was just charging my phone, so I thought the cable was broken. Next I tried it at home on my desktop computer, with another cable, and it did the same (several reboots have passed).
I don't know if someone already tried it, but when you enter the bootloader, it says "Serial". Normally when you connect the USB-cable it changes to "USB" (at least with my kaiser, universal and wizard). on my phone it didn't...... can anyone check this for me??
to enter bootloader: hold volume-down-button and pres soft-reset-button.
thanks in advance!
InjecTioN said:
It seems this problem is spreading, as i'm being terrorized by this stupid bug... This afternoon I've tried to get internet on my laptop (by connecting my phone to it), but it was just charging my phone, so I thought the cable was broken. Next I tried it at home on my desktop computer, with another cable, and it did the same (several reboots have passed).
I don't know if someone already tried it, but when you enter the bootloader, it says "Serial". Normally when you connect the USB-cable it changes to "USB" (at least with my kaiser, universal and wizard). on my phone it didn't...... can anyone check this for me??
to enter bootloader: hold volume-down-button and pres soft-reset-button.
thanks in advance!
Click to expand...
Click to collapse
Verified - I cannot flash with USB.
Bright.Light said:
Verified - I cannot flash with USB.
Click to expand...
Click to collapse
thanks for your help.
I've flashed my device with the newest official from HTC, and it still doesn't connect with the usb-data (i used the "flash-from-SD" -method).
The strange thing was that it happened suddenly... i never use a headset with cable, so its almost impossible the connector is broken. Any ideas people??
btw, the device isn't SPL flashed, so i can't use other roms beside the official roms...
Same thing happened to me. No USB sync, no USB connection at all; it only charges. Thankfully I had a chance to flash to a custom ROM before this happened.
The only way I can sync my data is to use a bluetooth USB in my PC. Works quite well with my contacts, calendar, & email, but I have yet to try to transfer any large files.
The bluetooth USB I went with was ASUS USB-BT21 USB 2.0 Mini Bluetooth Dongle. It is VERY low profile, too, but I would have liked for it to come with an end cap like those USB flash drives, otherwise I have yet to find any complaints about it. The price was great and so much cheaper than spending an additional $70-$100 to get my USB port on my device fixed.
Here's my saga: No Syncing, No USB Connection
Best of luck!
Debbie
this happened to me before...when you connect your devivce to your laptop/comp, are you guys not getting the little pop up that says activesync & disc drive...??? if so jus make sure at least one of those are checked...sometimes both of the circles will be blank, thus the comp will simply charge it...
unplug the device for approx 10 sec then plug it in again, and the box should pop up again...
also...if you are tethered to your comp using the tp2's internet, your comp will not recognize your tp2's storage...
da9th_one said:
this happened to me before...when you connect your devivce to your laptop/comp, are you guys not getting the little pop up that says activesync & disc drive...??? if so jus make sure at least one of those are checked...sometimes both of the circles will be blank, thus the comp will simply charge it...
unplug the device for approx 10 sec then plug it in again, and the box should pop up again...
also...if you are tethered to your comp using the tp2's internet, your comp will not recognize your tp2's storage...
Click to expand...
Click to collapse
was the first thing I checked. thanks for your input though
InjecTioN said:
thanks for your help.
I've flashed my device with the newest official from HTC, and it still doesn't connect with the usb-data (i used the "flash-from-SD" -method).
The strange thing was that it happened suddenly... i never use a headset with cable, so its almost impossible the connector is broken. Any ideas people??
btw, the device isn't SPL flashed, so i can't use other roms beside the official roms...
Click to expand...
Click to collapse
I did not know one could flash to new ROM by use of the SD card?
Mine is de-HSPL, so now I can not select another ROM anymore. (Got the 6.1 default one again)
Bright.Light said:
I did not know one could flash to new ROM by use of the SD card?
Click to expand...
Click to collapse
I've never used the SD-Card method myself, but now will have to due to my USB port no longer working.
I've been syncing by using Bluetooth USB and just tried transferring files via Bluetooth and it worked like a charm! Smaller files were instantaneous and large files took longer (of course), but also worked fine.
I just tried copying over a RHODIMG.nbh file and that bugger worked (188MB)... Excellent!!!
I did buy a USB card reader to transfer files, just to be on the safe side, but I must say that this little Bluetooth USB that I picked up is working awesome.
Debbie
i exactly have the same problem.I guess i need to send it back
I read a bunch posts on UBS issues but not that solved my problem.
Ok this seemed to start after I installed the ABLDroot tool by chainfire.... but sense then I have tried other roms, and other phones ATM I got a S3 and my S3 hooked into my computer... I going do my best make this easy for you and explain it right.
I have 2 usb ports on my computer which sucks (only having 2) its a labtop. Anyway I have 2 USB DLINK hubs.... one goes into computer and the other goes into the usb hub.. hub1----hub2----computer
hub 1 has nothing in it.....
hun 2 has my S3, S2 and the other hub pluged into it
my computer has 1 usb hub pluged into it and other port is used for my mouse (via a small hub) I do that because its usb mouse and it won't register right on the hubs.... anywaus
Easy problem could this be usb hub? Doesn't seem to be but I can't say I can tell for sure because I need stupid thing to use the phone unless I just except not being able use anything else USB (which arn't connected right now at wern't when the problem started)
This started when installed that ABD tool. Then my computer started saying wrong device error. So I went ahead and installed older drivers which fixed that problem. But the main problem is sometimes when I move stuff on my S3 like if I copy files and stuff I can see they moved on the phone but when I go to the computer and try to find my files there not there. Not moved. Or I see blank folders. Or worse even though I can use file commander still I am unable to see my phones on Cdrive. I see them in devices but not C drive.
sometimes problem goes away sometimes not. what is this ? the older drivers? the abd tool? I can't tell I tried to take one away at a time and while problem would go away often times it still happens once in awhile.... im going try some more tests with the usb plugged strait in but the problem stilll happens ..
Though its better if I don't use the hub thats not good enough for me I want problem gone
I use windows 7 any ideas thanks
only thing I dunno is could having a S2 conected mess with drivers maybe? doesn't seem so.
Any ideas? Different drivers or ... a program or... i dunno man shezzzz
Having the S2 connected shouldn't change anything. Your laptop should see both.
My guess is your USB hub but could also be from the older drivers.
This is a problem specific to your pc (either hardware or software), it's really hard to know exactly what's wrong without being there to test it.
Just upgraded from an S2 to an S3 and am having an issue with getting my S3 to connect to my PC that I previously had S2 drivers on.
I am having an issue however that I cant seem to figure out. When I connect my phone to my PC via USB cable it detects my phone for a few seconds, then trys to install drivers and then the connection disconnects and reconnects a few times a second. To the point where my PC is beeping all the time because it is recognizing a new device and on the notification tab on my S3, connected to PC flashes off an on. I have tried reinstalling drivers, booting the phone already plugged into pc, switching to camera mode, turning the pc and phone both off and starting together and none of these things help.
I did some searching and it appears that a few others have experienced this when upgrading from a different Samsung device, however even after going to device mgr and uninstalling those drivers I still have the same issues. I dont know if there are some drivers that are not displayed or something. I have tried a different cable with no avail. However when I connect my phone to a new PC that has never had a samsung device installed before it works with zero issues. Someone recommended using the Naked Drivers however I cant even get to the point to pick which driver to use before the device starts disconnecting and reconnecting on my PC several times a second.
Has anyone else experienced this? Thanks.
-Sayajin
Hmm, try this. Dial ##3424#, tap on PDA, then Qualcomm USB Setting, tap on MTP+ADB, ok. See what happens now.
I'd swap out the USB cable and try a different port, if still not working then install Kies and let it run the connection diagnostics which has resolved this issue for me in the past.
Sent from my SPH-L710 using xda app-developers app
Hey guys, just wondering if anyone had this before:
I am able to charge the devices, but nothing related to USB transfer works...
I am stock, not rooted, with latest version available for the Telus' E973
I've tryed 3 PCs, 2 cables, hard resetted the thing but nothing...
So far, I'm thinking I'd RMA the thing...
Does phone ask about mode when you plug it in?
Also, does the computer make any sound or showing that it's plugged in under computer or device manager?
Sounds like USB cable problem, but if you tried 2 cables the odd it's the problem are really low.
Sent from my Galaxy Nexus using xda premium
Nothing on either the computer nor the device, no changes in the device manager...
Was having same problem.
Redownload/install the ADB drivers or whatever they are, and all other drivers. Worked for me. Mainly the ADB ones.
You mean on a computer or on the device?
I've tried on multiple computer which were working before, and nothing is being "added" when pluging in the device, so it's most likely not a driver issu on the computers.
Maybe you broke the connector? What os does the pc have
Tried with Windows 7 x64 and x86 and Windows XP, same thing on 3 PC's
No reaction either on the PC's or the device.
Definitely broken connector
I'll keep you posted, I'm going to check out with my reseller tonight or mid-day.
So far, I understand that no one had this issue?
Thanks for all the input!
Got there during lunch, it's send out...
Now I'm stuck with a crappy Desire HD...