Hi all, just want to describe some problems I've been having over the last week or so.
Basically, my Orbit suddenly developed the habit of randomly freezing and displaying wierd patterns on the screen and requiring a soft reset and also just randomly restarting.
I first noticed this about a week ago, the phone did fall out onto the driveway a few days ago but it wasn't nothing it hasn't been through before and the screen is FINE, no dead pixels nothing. This is the ROM I had on it when it first started happening: http://forum.xda-developers.com/showthread.php?t=912989
My initial thought that it was something do with something installed on it, perhaps a software issue so I did a hard reset but same problems. I changed the ROM a few times but same problems. It's getting to the point where I have to look to buy a new phone.
It's quite difficult to describe what happens when the device freezes. I will try and get a picture or video but it's at random . The best way I can describe it is that it the device freezes, a section of the screen goes black slowly before the remaining section fades to black completely sometimes showing white lines. Moreoever, when I say the screen goes black, I don't mean that it goes off, the screen remains on but black.
Perhaps it is a hardware issue with a loose/faulty connection somewhere? My first thought was that it could be down to the screen connection but when the phone is working, the screen is absolutely normal.
Any suggestions are welcome. Please bear in mind that I've got no trouble in opening the device if needs be (had to change the LCD screen myself, I know, I know, go me! ). Thanks in advance!
Just noticed something. I've had it lying around re-filling up the inbox from a backup but as soon as I attached the charger, the problem occured, so could it be down to something from that as a result?
I've just managed to take a few pics. Theres quite a bit of glare unfortunately however this type of pattern doesn't always occur, sometimes it's less noticable than that.
http://imageshack.us/photo/my-images/69/pict0189n.jpg/
http://imageshack.us/photo/my-images/232/pict0190z.jpg/
hi dude,
my first thought was battery but now thinking you might have a loose connection with the motherboard and lcd.
i would check lcd ribbon that connects to motherboard first, obviously you know exacly what i meen, if that is not the problem i would buy a new battery (charge while off, do not turn on untill fully charged new battery)
if both of these do not do the trick then i would consider buying a new device. (unless anyone else has any ideas??)
thanks
Rn
Related
Last night I was out and during the night I pulled my desire z out of my pocket to find that the screen was dead, the soft touch buttons were still lit up and working but no display. I pulled the battery and tried to reboot and no luck, you can hear it booting and even unlock/receive calls and txts etc once it has booted up just the screen stays blank the whole time so have to do everything on feel.
Essentially does this just mean my screen has a hardware fault? is it worth trying to fix? I assume the only option would be to purchase a replacement screen and dissemble and reassemble it?
(warranty is not worth it as I live in New Zealand and would have to send my phone back to the UK where I bought it from, also I have dropped it quite a few times so probably voided anyway...)
Thanks in advance for any input
Does it never display anything? So not even a flash during boot or something?
Because then it is probably a hardware problem.
Since the soft touch buttons do still work I think there might be a little crack or something in the flat cable that connects the bottom half with the top.
Maybe you could check whether you can see if the cable is broken or not?
The best thing to do then is to look for a replacement and try to fix it yourself or bring it to a shop where they can do it for you.
No it never displays anything, completely dead the whole time. The touch input is still working though as I answered a phone call this morning on it by making the usual gesture just without being able to see anything. Doesnt seem to be anything wrong with the cable itself as far as I can see. Yea might have to get someone to have a look at it.
My phone is acting the same. I dropped my phone in the pond before, but pulled battery out on time and had it in rice for a day. My phone was still working for about two weeks after that incident. I dropped it and had one little crack at the top of the screen and about a week after that it died when I had a water balloon fight with the phone in my pocket. D;
Do any of you know if the replacement lcd screen/digitizer for the Desire Z would work for the G2?
I had the same thing happening to my G2 screen, only it was intermittently working for a little while, then just completely died and wouldn't work. It was doing this crazy flickering thing then the back light wouldn't go on at all. If I held the phone at a certain angle in the sun, I could see that the pixels were indeed working on the display, but there was no backlight to make them normally visible.
So I purchased a replacement screen from ebay and carefully followed the directions on a youtube video for a G2 take apart. Its not a hard task to take apart and get down to the screen itself. It was rather easy. After putting it back together the screen still didn't work! Sounds work, i can also receive calls etc. But the screen still doesn't work!
Is there any way that this could be a software issue?
Oh and PS, I believe the LCD replacement would work for both the desire Z and the G2. They are identical phones after all right? I'd say its a safe bet. The screen I bought was only 35 bucks. Didn't think that was a bad deal.
Another dead screen or something else?
Few days ago my phone fell of the couch onto a rug - no big deal, so far it has survived much worse, but when I picked it up, the colors were all messed up - overly green and red. Tried restarting - no luck. Everything worked fine, except the colors, but then the screen turned of completely. I could hear notifications, phonecalls, but the screen was dead. After some tapping on the screen, it turned on again - with ****ed up colors. Then started flickering and was gone again. Few more times I could turn it on by tapping before it was dead for good.
Figured, after all these drops it survived, maybe the screen connector is a bit loose. I mean, I could sometime get a contact when tapping it, so I dissasambled it completely, secured all the connection, put it all back tougether and fired up - same thing: dead screen, phone working.
Has anyone had such problem before? Is it screen that is dead, or connector or... I have no clue... I would like try to fix it on my own, with some replacement parts I could get on ebay - but, what gave?
Hello XDA members, this time I'm writing to all of you to tell you something that happened to my Optimus G E987 from Claro Argentina, also, to ask you something related to the topic.
I bought this phone about 4-5 months ago, and I have taken really good care of it, without using any film protection or case, it was working perfect and with not a single scratch on it, not even a little hit.
But then, some days ago, I decided to "protect it" a little bit, so I got one of this:
htt-p://i[dot]imgur[dot]com/YtgK1aS[dot]jpg
htt-p://i[dot]imgur.com/la1kI5e[dot]jpg
(Sorry, I'm new to this forum so it won't let me post links)
I used it like.. dunno, 3-4 days. One night, my phone was on 53% battery, to lazy to charge it so I just let it like that. Next day I gave it some use, so it dropped to 33% of battery life, I had to go work so I turned it off. When I finished, I tried to turn it on again, but nothing happened, tried more times and nothing, then I noticed I liiiitle light in the screen, the phone was turned on, but with REALLY low visibility, almost everything black but with a little of sight.
I though it was just a battery problem, so I charged it, but to my surprise, nothing happened, well something did happen, the little bit of sight that I had just went full black with no visibility. I noticed that the touch screen and buttons actually worked, I could "easily" navigate through the phone by just using it as normal, but without seeing (you can do this by just knowing your phone a bit).
And that's the story, basically, after using that case, the phone "casually" stopped working properly, all I got was a functionally phone with a black screen.
I managed to connect it to my pc through wifi and launched Android Screen Cast, to see what was happening on my phone. The glow was at 100% (I tried changing it) and everything seemed normal.
If you don't want to read, here is a TL;DR
>Bought Magnetic* Flip Stand Leather Wallet Case for Optimus G
>Some days after, phone screen stopped working (phone was still normally working, just with a full black screen)
About the Magnetic thing.. is there any possibility that this was the problem? the magnetic thing?
Btw, I sent the phone to tech service because it was still on warranty and they have me a new one, now I'm scared of putting it again in the leather case I bought, I don't want this to happen again.
Something to comment? hope you can give me some advice, thanks in advance!
Also having similar problems as you. Somehow, i am quite sure its the stock rom causing the problem.
Had the very same issue few weeks ago, had to send the phone back to LG ( who replaced the motherboard :/).
I was also on stock rom, had root and unlock bootloader (of course I clean all that **** before sending it back).
For my part, I was unable to go to recovery and download mode was quit impossible to access (may be my finger fault )
BUT! some time if I let the phone off for a moment or spam the power key, the backlight turn back on until I power down the phone, so it's could be a software issue ...
Anyway, an other info, when the backlight was off, if i tried to change backlight level i was getting a error message about overeating or something like that...
The battery on my HTC 10 was completely shot and needed to be replaced. I'm a careful person by nature and this being my first phone repair, I bought an extra screen just in case something happened getting it apart. Followed a guide by jerryrigeverything on how to take apart the phone, got the battery replaced, everything seemed to go smoothly. When I went to test the display before screwing everything together, the new screen I installed lit up, but the right half of the display only showed as a repeating segment from the middle of the screen. Thinking the connector was loose, I disconnected and reconnected the display and made sure everything was tight: same problem. I reinstalled the original display, which I made sure had worked after cutting through the adhesive before I disconnected it, and now the old display is also showing the same issue.
The touch screen on the broken side of the display still works, I'm able to type PIN numbers and whatnot even though I can't see them properly. Only thing I can think of is maybe the connection actually got some debris or something inside of it? I don't think I damaged anything, as I was super careful, but it was also my first time opening up a phone.
Sorry for the inefficiently worded post. Any help would be really appreciated.
Did you resolve this?
I have exactly the same issue you describe after my screen replacement (with two new screens) Believing the first was a dud.
I have done many screens/batteries on my m7, m8's previously never having a problem.
I'm currently back to running my M8 and miss my 10!
Anyone reading this and has any suggestions they are all welcome!!
Thank you in advance
Exactly the same issue this guy has
https://youtu.be/RpdCuMiTOn8
I'm now wondering if it is just bad aftermarket screens?
Has anyone else replaced their screen successfully, if so where did you get the screen?
Thanks Rory
I have been having the same problem. I just tested screen number 4 that has the same exact problem. Is there a specific brand that is known to test well?
I dropped my 10 in water at work...believe it was a salty water at that. It stopped working completely. I opened the phone to check the internal components for damage and I broke the LCD doing so. I replaced the battery and the screen at almost the same time. I think it may have been a week or two apart.
The battery is still working. The screen worked initially but the phone kept getting really hot and the heat kills the phone. I tried keeping it cool at all times which kept it operational. It hasn't been activated since I quickly replaced the phone with another of my lines upgrades. I went back to the phone to check it out and try using it as a replacement for my daughter but the screen no longer works.
The battery charges just fine...the led light indicates that well. I've tried reinstalling it several times with no success getting the screen working again. I tried the original screen to check and I could see light and it was responding but its not usable so I'm stuck with a phone that has a new non-working display. I think the brand was called DIYRepair or similar.
If anyone has encountered this and has advice...I'd be happy to try anything.
Expecting bootloop to hit my Nexus 5X , I got something different, display related..
The problem started few months ago, but I managed to solve it with one or more restarts. It came randomly, sometimes few months between each, and it looked like like this : imgur.com/N5vYzDt (photo from nexus 5 i found on web that had same problem).
And today same thing came back, I was watching something on YouTube and the screen started flickering and distorting, few seconds later it blacked. Tried to restart it X times, nothing. Tried to hold power+volume down button, I heard vibration but nothing on display (only backlight). Tried to put it away for few hours, thought it was heat related, still nothing. I see that display lights up a little (backlight) but thats all.
What could be possible solution for this? Its sad to see that this happened, phone was in excellent condition, never had major lag or anything..
-------
Took it to unofficial service, they said it could be display to replace. How come can this be if display is working (atleast backlight), could it be some connector or something? I don't want to throw money for something that may not work, or be temporary solution...
Atleast I learned something, avoid LG no matter what.
Hello , nice to meet you all. I am a new XDA user so apologies if i do any mistakes.
Yesterday, i got the 2 GB Ram variant of the LG G3 D855 from a relative. The phone almost works fine, except for two problems:
The first problem is that sometimes, the phone either locks up for about 3 seconds and shuts off (or maybe the screen shuts off? not sure), or either it completely reboots on it's own. I know, there is already information about this on the internet, however, some people say that it's a battery problem, some say it's an overheating problem. I am just confused. By the way, the issue happens no matter if the phone is charging or not. It also happens even when the phone isn't overheating, although it happens less. I may try a battery replacement, but unsure if it will fix it or not.
The second issue is, it's not really a critical issue, but it's just annoying. For some reason, especially when the phone overheats, the screen's right bottom side starts glitching (It also mostly happens on the home screen for some reason). And no, i don't mean flickering. Some glitchy lines appear at that portion of the display for about a millisecond and then goes away most of the time. Today the phone overheated when i was watching YT once and those lines appeared for like 5-10 seconds.
Also, i've noticed that the phone overheats a lot. Like, it gets quite hot sometimes.
I've already tried a factory reset, but it did not fix anything. The phone is running the stock Android Lollipop 5.0 firmware by the way. I did not want to take a risk trying to upgrade the phone to Marshmallow or install a custom ROM because of these problems.
I don't want to spend too much on the repairs of this phone since i've already got an another phone with almost the same specs as the LG G3. But i also want to use this phone. I just like it's design so much. Please tell me if it is worth getting it fixed and what i should do to get it fixed at the lowest cost possible. By the way, i don't understand much about the hardware of smartphones (I will get it repaired to an expert). So please, try to explain the problem as simple as you can do. Thank you and i wish you all a great day.
UPDATE: I've also noticed that the phone also has the screen flickering/disappearing issue.
However, asides from that, i've found an another issue too. So this evening, the phone was overheating too much so i decided to let it cool down a bit. So i closed the apps and put it into sleep mode. After about 5-10 seconds, the phone started doing REALLY LOUD tv static like noises. I immediately pulled the battery out, and i am afraid to turn on the phone because of that. I think the sound didn't come from the battery but i am still afraid.
I will bring the phone to a repair centre. But at this point, i don't know if it is worth getting it repaired. I am so confused. Is the phone dead or not? I've tried pulling the battery out and trying to boot the phne while it was getting charged (DON'T DO IT for your safety) and i get the "No battery" screen. I hope anyone that understands the hardware of this phone will help me. Thank you all.