Related
Not sure if this was on the fault of my carrier or not, but I actually had this problem before and resolved it once.
I was running 3.60.1 and even tho I had Unchecked "Enable Advanced USB Connection" or whatever under USB to PC in the Connections Tab, My phone would not connect to WMDC (I use Windows Vista). I would just connect to get my contacts via Bluetooth, which worked fine.
I am a heavy user of tethering via USB as I like to charge the phone while I am connected. 3.60 series has been pretty good...I haven't had a complaint really since I upgraded from 3.0 (Which IMO is a bit more stable but I'm not sure why). Every once in awhile, I lose connection. I'm not sure why it does this. I'm using radio 1.48 and I have been using it for both 3.0 and 3.60. I had problems using 1.50 as data connections would drop instantly...so I never caught on to that radio. I am located near the NYC Metro area.
The latest problem I had was...sometimes my data connections would drop and would not reconnect without restarting the phone. I'd SR the phone and all of a sudden during the boot (while still connected to USB), my WMDC picks up the device. Not sure why it chooses to do it after I've had the ROM Flashed for several days now...but I go ahead and set it up only to see my phone assumes a permanent Flight Mode. Under Comm Manager, I am unable to switch back to Phone Mode. I do not have access to Phone settings. I cannot even open my dialer.
I've done it before and I don't save that many new things to my phone...so I went on to HR. After HR...the phone was completely unstable. During the loading of the "customizations" (which correct me if I'm wrong...is the EXTRom), it will install everything and then hang after finishing the last one which I believe was the theme of ATT.tsk.
Frustrated, I decided to flash back to 3.0 I still use 1.40Oli (HardSPL V6) which was always fine and I was never able to update to 2.10Oli for I have weird issues with SSPL and Vista. I do everything normally...I get to the progress screen. It hangs. No problem. Run RUUWrapper again...bootloader screen is accessible and my SPL and HTC_BOOT should be unaffected. Still hangs. I try to flash a radio...hangs. Almost everything I try to flash...hangs.
I've tried multiple USB Cables...thinking that was the problem...same problem though. It gets all the way to the progress and the Bootloader screen recognizes when its plugged to the USB so I don't think that's the problem.
My phone is stuck in bootloader right now and nothing will flash to it. No matter what it will get to progress and load 0% of any NBH I try to flash.
The main point of this post:
1. What caused 3.60.x to not connect to WMDC from the beginning via USB...only to do it randomly later?
2. What caused the corruption to the ROM leading me "GSM-less" stuck in Flight Mode and no access to anything to turn it back on to Phone Mode?
3. What is the cause of my phone not updating any NBHs I try to flash (OS Only/Radio Only/Original Shipped) ROMs?
I'm not sure if I was the only one receiving these errors. I have not updated my signature in awhile but I was running:
HARD-SPL V6: 1.40.Oli
Radio: 1.48.00
ROM: VP3G 3.60.1
Thanks for your help in advance.
Important - Read First!
First of all you must know that everything you do is on your own risk. Your device was not designed to run GNU/Linux or Android and that's why you shouldn't expect everything to be perfectly safe. If you don't want any troubles then simply don't tamper with your phone. On the other hand, installing Rhobuntu is probably less dangerous than installing alternative ROM's, because it doesn't touch your ROM and runs completely from the SD card. If something goes wrong and the system would hang up, you always can remove the battery and boot into Windows Mobile. Still, we can't guarantee you anything and we won't be liable for any damage that might happen to your device. If you don't accept this, don't install Rhobuntu.
At the moment two problems are known to occur when using Rhobuntu. They are, however, not Rhobuntu specific and may also occur when using Android.
1- After booting back into WinMo, you can't install or run unsigned apps. This problem probably has something to do with the way haret kicks WinMo out of the RAM. It also seems to occur only in combination with the use of Exchange Server. The only known solution at the moment is Hard Reset. Some users also reported that it can be fixed by using Visual Studio 2008. Check out this threads:
o Not digitally signed with a Trusted certificate/ Activesync keeps UNINSTALLING!
o Program... is not digitally signed with trusted certificate. HELP!
2- Since we still have no proper battery charge indicator working, you might not notice that your battery is completely drained. Deep discharge is, however, not good for batteries and may in some cases even damage them. Here is a thread dealing with this problem when running Android
o Android killed my USB connection, please help
The majority of Rhobuntu users doesn't face these problems, but just in case, you've been warned.
WIKI http://wiki.xda-developers.com/index.php?pagename=RhodiumUbuntu
WEBSITE https://sites.google.com/site/rhobuntu/
This build by Walter79 and the Rhobuntu team:
Rhobuntu 9.04 19.09.2010
changelog:
- zimage update (Xandroid Build 16/09)
- sphone 0.04 (thanks AmiPro)
- 3G scripts update (thanks AmiPro)
- sound works partial (thanks to phhuson) !!! run /sdcard/ubuntu/playwav2 after boot !!!
- alsaplayer added
Download:
Link1: http://www.megaupload.com/?f=RWDJWUN0
Link2: http://rhobuntu.4shared.com
Debian Squeeze Test 19.09.2010
For more information please look at this post http://forum.xda-developers.com/showpost.php?p=8186181&postcount=1208
Download:
link1: http://www.4shared.com/dir/n-2ObqP_/pro2-debian.html
Old Build (27/06/2010)
*http://www.megaupload.com/?f=RWDJWUN0
*http://rhobuntu.4shared.com
Old Build (13/05/2010)
*http://www.megaupload.com/?f=RWDJWUN0
*http://rhobuntu.4shared.com
Old Build (14/04/2010)
*part one:http://rapidshare.com/files/375930803/Jaunty_14_04_2010.7z.001 MD5 77430e728bb17277e671cc55ae03161f and part two: http://rapidshare.com/files/375939439/Jaunty_14_04_2010.7z.002 MD5 523589000dcd5d1dcea668bbe51253af
* http://rhobuntu.4shared.com
* http://www.megaupload.com/?f=RWDJWUN0
Old Build (11/04/2010)
* http://rs427.rapidshare.com/files/374730149/Jaunty_11_04_2010.7z
* http://rhobuntu.4shared.com
* http://www.megaupload.com/?f=RWDJWUN0
Old Build (10/04/2010)
*http://rapidshare.com/files/374138895/Jaunty_10_04_2010.7z
*http://rhobuntu.4shared.com
Pretty cool idea, keep us posted!
Definitely an awesome idea, and one I had been thinking about myself since my original Touch Pro days. An embedded version of Linux should run great on these devices. Hopefully momentum will grow surrounding this.
thats very interesting. any pictures of this running? maybe things can be pulled from android.
THANKS!!!! downloading now!
tried it on my Touch Pro 2 (AT&T Tilt2), No luck. Started to boot, Complained about /etc/init then poof reboot after 7 seconds. Am I missing something.
aq3e said:
tried it on my Touch Pro 2 (AT&T Tilt2), No luck. Started to boot, Complained about /etc/init then poof reboot after 7 seconds. Am I missing something.
Click to expand...
Click to collapse
Did you change the mtype in the sartup script to the tilt2, the one i used is set for the rhod100, i hope that helps. Is anyone else's not working btw?
Help!
I extracted all the files on to a newly formatted 2GB card.
Ran haret and everything ran fine. Bit 'interesting' navigating round the screen but got there in the end.
However, since rebooting my phone back into WM I cannot run any unsigned programs such as haret that worked fine before.
The error says "The file blah cannot be opened either it is not signed with a trusted certificate..."
Any idea what's changed and how I can get my phone back to how it was?
R.
dicko99 said:
I extracted all the files on to a newly formatted 2GB card.
Ran haret and everything ran fine. Bit 'interesting' navigating round the screen but got there in the end.
However, since rebooting my phone back into WM I cannot run any unsigned programs such as haret that worked fine before.
The error says "The file blah cannot be opened either it is not signed with a trusted certificate..."
Any idea what's changed and how I can get my phone back to how it was?
R.
Click to expand...
Click to collapse
Wierd, my winmo works find, minus the calibration issue, it's brilliant, we need some linux Devs to look into this. as a windows user, i have no idea on what to do
Thanks (All we need now is win XP )
Badwolve1
I think something got corrupted/overwritten on my phone...
I cannot run any unsigned apps whether they are installed on the storage card or internal memory.
I cannot even install new apps! When I run the cab file, I get the usual "This program is from an unknown publisher..." and when I select yes for continue it immediately comes up with "Installation of blah was unsuccessful."
Time for a hard reset? I'd really prefer not to if anyone can suggest a better way of getting back to how it was.
R.
dicko99 said:
I think something got corrupted/overwritten on my phone...
I cannot run any unsigned apps whether they are installed on the storage card or internal memory.
I cannot even install new apps! When I run the cab file, I get the usual "This program is from an unknown publisher..." and when I select yes for continue it immediately comes up with "Installation of blah was unsuccessful."
Time for a hard reset? I'd really prefer not to if anyone can suggest a better way of getting back to how it was.
R.
Click to expand...
Click to collapse
did you install anything recently, could try uninstalling it
dicko99 said:
I think something got corrupted/overwritten on my phone...
I cannot run any unsigned apps whether they are installed on the storage card or internal memory.
I cannot even install new apps! When I run the cab file, I get the usual "This program is from an unknown publisher..." and when I select yes for continue it immediately comes up with "Installation of blah was unsuccessful."
Time for a hard reset? I'd really prefer not to if anyone can suggest a better way of getting back to how it was.
R.
Click to expand...
Click to collapse
try installing SdkCerts.cab
http://forum.xda-developers.com/showthread.php?t=554240
the cab is included with the rhodium keymapper zip file. (keymapper app is worth installing as well )
sdkcerts won't install. It has the same problem as other cabs where it prompts to say the program is from an unknown publisher and when I tap Yes to continue it still fails with "Installation of SdkCerts.CAB was unsuccessful."
Tried booting it up on my Verizon TP2 and all it does is run haret and then freeze.
Thanks for putting this together, sebbo90. It boots nicely, and actually performs quite well on my Tilt2. I hope some of the developers take notice of this project and consider fixing the major usability issues like the front keys and the display calibration.
After the first boot I cant get the GUI to run anymore. Removing the directory from the SD and uploading a fresh copy fixes it for one boot only. After that it just hangs at command line.
spdweb said:
After the first boot I cant get the GUI to run anymore. Removing the directory from the SD and uploading a fresh copy fixes it for one boot only. After that it just hangs at command line.
Click to expand...
Click to collapse
How did you even get it to boot?
EDIT: Do you think it will not boot for me since you all are using GSM and i am using a CDMA phone? Some settings may need to be changed i guess. I have been messing around but no luck.
spdweb said:
After the first boot I cant get the GUI to run anymore. Removing the directory from the SD and uploading a fresh copy fixes it for one boot only. After that it just hangs at command line.
Click to expand...
Click to collapse
I had this problem what i did to fix it was to was to do a full reformat on my sd card (not a quick one) this then helped and now it boots everytime. Hope this helps
sebbo90 said:
Did you change the mtype in the sartup script to the tilt2, the one i used is set for the rhod100, i hope that helps. Is anyone else's not working btw?
Click to expand...
Click to collapse
If the mtype needs to be changed, what should it be instead of the default 2292, forgive my ignorance.
EDIT: must be a fluke, it booted now, did not change a thing. Re-extracted the ubuntu rar and shoved it back on the SD and booted. Great Job. All we need now is calibration to get started.
sebbo90 said:
I had this problem what i did to fix it was to was to do a full reformat on my sd card (not a quick one) this then helped and now it boots everytime. Hope this helps
Click to expand...
Click to collapse
I got it working now. It was the directory structure I was using. I spent about 2 hours last night working on the calibration issue. If I could get that working it would be sweet. Tried a newer version of haret and tweaked the startup.txt a bit but the calibration still goes out of range.
On a brighter note, the calibration works fine when booting xdandroid with haret though it is a manual calibration there is hope anyway.
Android was working perfectly ok with a 3G connection, but the new build isn't connecting. Any help? I didn't see anything in the FAQ.
I uninstalled the CAB from WinMo and deleted excess files off the microsd card.
Any idea on what's going on?
AVakil said:
Android was working perfectly ok with a 3G connection, but the new build isn't connecting. Any help? I didn't see anything in the FAQ.
I uninstalled the CAB from WinMo and deleted excess files off the microsd card.
Any idea on what's going on?
Click to expand...
Click to collapse
Is the force cdma option enabled in your startup? This only applies if you are on a CDMA carrier, obviously.
Also, don't use MGJDroidUtil... it has been known to screw up the startup.txt, I thought they were updating it tho... Haven't heard anything about it so just stay away from it...
Thanks for the tip regarding not using the launcher. I have noticed that startup.txt getting corrupted.
The force CDMA is enabled in my startup. I am on Sprint.
same....
I have the same problem. Force CDMA is checked. The BLAZN and default releases were my first attempt at this when audio support was added. Both of those tested and worked as expected. So that's two of us so far.
BTW I told myself I'd donate once some great minds got audio working. Is it best to donate on the main page or to any other specific party?
lip008 said:
I have the same problem. Force CDMA is checked. The BLAZN and default releases were my first attempt at this when audio support was added. Both of those tested and worked as expected. So that's two of us so far.
BTW I told myself I'd donate once some great minds got audio working. Is it best to donate on the main page or to any other specific party?
Click to expand...
Click to collapse
AVakil said:
Thanks for the tip regarding not using the launcher. I have noticed that startup.txt getting corrupted.
The force CDMA is enabled in my startup. I am on Sprint.
Click to expand...
Click to collapse
To both of you... you may want to format & start over. lip008, you said "force cdma is checked" - that sounds like you're using MGJDroidUtil, because the startup.txt is a text file... you have to make sure the force cdma command is in the cmdline section.
Oh and for donations, I'd say the general XDAndroid Donation page is sufficient
I'm on GSM (T-Mobile), and I had the same issue (not the BLAZN build, the regular one)
Ok, how about APN settings? sukru, others, have you checked those?
Honestly I haven't had to add the APN manually for several builds, but maybe there's a regression in the new build.
As always, make sure your rootfs, zImage/modules are up to date.
Heres the solution if you are on sprint
Boot into windows mobile and connect to pc so you can access the files in the andboot folder on your sd card. .
or (the purpose of this is so you can edit your STARTUP.TXT using notepad)
You can take out your SD CARD and put it in a card reader and do this too.. as long as you are in windows mobile..
DO NOT DO THIS IN ANDROID..
Once you get access to the SD CARD files.. go into the ANDBOOT folder..
locate STARTUP.TXT and edit it with notepad
locate the long line of commands that starts with "Set cmdline"....
read the entire line and somewhere in the middle you will find a part that says..
force_cdma=0 (remove this part only)
and make sure you have this at the end.... htc_hw.force_cdma=1
NEXT: SAVE YOUR FILE.. AND HERES THE IMPORTANT PART..
***** BOOT WITH HARET.EXE***** NOT WITH THE MGJDroidUtil program...
THIS WORKED FOR ME.. and if any of the mods here want to add to this.. please feel free to clarify..
In lamens terms... On cdma network sprint only
THERE IS A CORRUPT ENTRY IN THE STARTUP.TXT that needs to be removed..
EDIT this entry using notepad while not booted up in android.
the entry needs to be removed mentioned above..
DO NOT USE: MGJDroidUtil to start android.. USE FILE EXPLORER.. AND start
HARET.EXE..
hope this helps..
MINE READS AS FOLLOWS:
set cmdline "lcd.density=240 msmts_calib=0x9f.0x39a.0x35c.0x78 7x00.a11=500 msmvkeyb_toggle=off pmem.extra=1 gsensor_axis=2,1,3 pm.sleep_mode=2 acpuclock.oc_freq_khz=716800 rel_path=andboot hw3d.force=1 physkeyboard=rhod400 htc_hw.force_cdma=1 "
lancevs, I appreciate then enthusiasm, but I don't think that would have any effect on GSM guys.
However, using MGJDroidUtil can still screw up anybody's startup.txt, regardless of the type of phone/radio... so he is correct in that fact:
DON'T USE MGJDROIDUTIL.EXE!!!!
Edit - didn't even think about it but sukru - do you have this force_cdma statement set to 1? For us CDMA guys it's required, but it probably will break you GSM guys if it is enabled... So check that out.
Yes for clarification
MY POST SAYS " FOR SPRINT USERS ONLY" at the TITLE...
GSM users, this does not apply..
I am on sprint and spent a good part of yesterday trying to figure out why i had no service.. I am on SPRINT which is a CDMA network..
arrrghhh said:
lancevs, I appreciate then enthusiasm, but I don't think that would have any effect on GSM guys.
However, using MGJDroidUtil can still screw up anybody's startup.txt, regardless of the type of phone/radio... so he is correct in that fact:
DON'T USE MGJDROIDUTIL.EXE!!!!
Edit - didn't even think about it but sukru - do you have this force_cdma statement set to 1? For us CDMA guys it's required, but it probably will break you GSM guys if it is enabled... So check that out.
Click to expand...
Click to collapse
Will check again tonight. Android was getting better each time, then it suddenly went down for me.
Hey guys. I had been running an early August (pre sound) release of Blazn, and everything had been fine. Today I decided to upgrade to get sound and 3D support, and every time I boot into Android it shows no signal, and shows I'm in airplane mode, and it will not let me turn the radio on.
I'm using a Sprint TP2, and I followed the instructions for earlier in the thread, but still no go.
Here's the line from my config file:
Code:
lcd.density=240 msmts_calib=0x9f.0x39a.0x35c.0x78 msmvkeyb_toggle=off pmem.extra=1 gsensor_axis=2,1,3 pm.sleep_mode=2 acpuclock.oc_freq_khz=716800 hw3d.force=1 physkeyboard=rhod400 htc_hw.force_cdma=1
Is there something wrong in it? I am launching Haret directly from TotalCommander File Explorer. Same problem if I use the config/startup utility.
Also, to install the latest version, I deleted the andboot and android folders on my SD card, then installed via cab.
That line looks correct, perhaps you should post your entire startup.txt.
Or just start with a clean build - wipe everything Android related and do a fresh install. The new startup utility is pretty slick, just be sure you check force cdma in the advanced section.
Seems to be random. About 30% of the time it will work, the other 70% of the time "no service" and no way to turn on the radio.
shawndoc said:
Seems to be random. About 30% of the time it will work, the other 70% of the time "no service" and no way to turn on the radio.
Click to expand...
Click to collapse
Well, perhaps you shouldn't use the update utility at all. It has been updated so it shouldn't corrupt the startup.txt, but I had issues with it... so personally I prefer to just use haret & modify the startup.txt manually.
I am launching Haret directly, see OG post.
shawndoc said:
I am launching Haret directly, see OG post.
Click to expand...
Click to collapse
Start with a clean build. Don't touch the startup utility, because you said you had previously. It's been known to corrupt the startup.txt, even these new builds I had my startup.txt go to 0 bytes.
hi I am having the same problems cant get android to connect with sprint on the tp2. I am no expert but have become very good at using windows mobile as a user not a developer so all i know is i downloaded a cab file that was haret version 9 28 it came with a little icon labeled android project when i launch it i get to a screen that lets me make some advanced setting and check for updates before and choose my phone model. It says aka sovereinty at the bottom. I have tried to boot without forcing cdma and it does not connect and when i choose force cdma it seems likes its kinda connecting but keeps getting a error message and then i force close and it automatically tries again. If i boot wiithout force cdma the i can connect via wifi but that works but seems to also disconnect after a few minutes, though that is not my concern for now. I tried with the sim and without. and have updated twice so i am know on 10 4. anybody that get help would be appreciated. I love my tp2 with windows mobile but am curuios to play with android being that sprint wont let me unless i change my plan and make me pay double. not interested because my tp2 works great now and has everything i need.
thanks
Windows Mobile: 6.5
XDAndroid: Rhod400
Installed Version: 2010_11_24
(Installed ProjectAndroid2.2BLAZN.092810 and ran update 2010_11_24)
Wifi works on WM but not on Android
Can turn on Wifi but Wifi goes off immediately.
Error message:
Sorry!
Application Settings (in process com.android.settings) is not responding.
I have my Haret.exe in andboot.
Thanks for your help in advance.
martian63 said:
Windows Mobile: 6.5
XDAndroid: Rhod400
Installed Version: 2010_11_24
(Installed ProjectAndroid2.2BLAZN.092810 and ran update 2010_11_24)
Wifi works on WM but not on Android
Can turn on Wifi but Wifi goes off immediately.
Error message:
Sorry!
Application Settings (in process com.android.settings) is not responding.
I have my Haret.exe in andboot.
Thanks for your help in advance.
Click to expand...
Click to collapse
1) do not overclock
2) do not tamper with the phone immediately after boot, leave it alone for a while (30 secs, 1 min)
3) do not fill the desktop with widgets, they eat lots of resources
If none of these works, while still NOT overclocking, delete data.img file inside andboot folder and start from scratch.
Cheers.
Pretty strange, since I have a Sprint TP2 and Wifi works perfectly.
You might want to start by renaming your data.img to something else to back it up, and then starting up. If after you boot Wifi works, then you know something is messed up in your data.img. Otherwise, you know it's something else and you don't need to wipe out your data.img.
Wifi can also easily get bungled if you update your kernel and don't update your modules file.
The kernel (zImage) and modules (modules-xxxx.tar.gz) go hand-in-hand, and they MUST be updated together.
1. Formatted SD Card with HP USB Disk Storage Format Tool
2. Deleted exchange inbox folder in SD Card (I have no idea why the formatting does not wipe it clean)
3. copied ProjectAndroid2.2Froyo.112210.cab to root of SD Card
4. Ran cab from explorer
Ran ProjectAndroid from WM
Ran Update
RHOD400
Cdma x
HW3D X
N AM DIAL X
Getting the following message:
Unable to scan for networks
WPA Wifi is on in WM
I renamed the data.img file... still does not work
manekineko said:
Pretty strange, since I have a Sprint TP2 and Wifi works perfectly.
You might want to start by renaming your data.img to something else to back it up, and then starting up. If after you boot Wifi works, then you know something is messed up in your data.img. Otherwise, you know it's something else and you don't need to wipe out your data.img.
Click to expand...
Click to collapse
Could you please post the link to the build you used? I used
sites.google.com/site/androidport/downloads
Thanks!
martian63 said:
Could you please post the link to the build you used? I used
sites.google.com/site/androidport/downloads
Thanks!
Click to expand...
Click to collapse
That is the one I use on my sprint tp2. Works awesome. I can even wifi tether. Did you download the one at the bottom of the page from Nov. 22?
Edit: sorry. just saw you gave that info. I have never tried that N american dialer. not sure what it does. do you still get the same error when you try to turn on wifi in settings?
ivwonka said:
That is the one I use on my sprint tp2. Works awesome. I can even wifi tether. Did you download the one at the bottom of the page from Nov. 22?
Edit: sorry. just saw you gave that info. I have never tried that N american dialer. not sure what it does. do you still get the same error when you try to turn on wifi in settings?
Click to expand...
Click to collapse
I hard booted my TP2 to factory settings, used the .rar files instead of the .cab...
getting the same message "Unable to scan for networks".
Yes, I am getting the same error when I try to turn on wifi in settings.
The instructions in xda is a bit misleading for .rar
The steps say
1. Unzip
2. Copy contents of .Rar to the ROOT of your SD card
When you unzip, the content is in folder "XDAndroid2.2Froyo.112210" sub-folder "XDAndroid2.2Froyo.XXxxXX"
The instruction should say, "Copy contents of "XDAndroid2.2Froyo.XXxxXX" to the root of SD card.
Please correct me if I am wrong. In any case, my wifi still does not work.
Have you tried updating manually? Also, you should get an 'andboot' folder if you go into that XXxxXX folder.
I also found a mistake with Reef's build... I asked him to update it. Basically he's not using a signed FRX03 image... I sent him a new bundle, doesn't look like he's updated it yet tho...
What I'd recommend in the meantime is to update this build manually. Download a new system.ext2, new kernel (zImage/modules - they go together!) and rootfs.
You can find all of those updates at http://xdandroid.com/wiki/Main_Page
arrrghhh said:
Have you tried updating manually? Also, you should get an 'andboot' folder if you go into that XXxxXX folder.
I also found a mistake with Reef's build... I asked him to update it. Basically he's not using a signed FRX03 image... I sent him a new bundle, doesn't look like he's updated it yet tho...
What I'd recommend in the meantime is to update this build manually. Download a new system.ext2, new kernel (zImage/modules - they go together!) and rootfs.
You can find all of those updates at //xdandroid.com/wiki/Main_Page
Click to expand...
Click to collapse
Downloaded the latest files individually. Updated the build manually by replacing the system.ext2, zImage/modules and rootfs. Modified the startup.txt to force cdma, keyboard to rhod400 and clock speed to 540672... getting the same error "Unable to scan for networks" error.
ivwonka said:
That is the one I use on my sprint tp2. Works awesome. I can even wifi tether. Did you download the one at the bottom of the page from Nov. 22?
Edit: sorry. just saw you gave that info. I have never tried that N american dialer. not sure what it does. do you still get the same error when you try to turn on wifi in settings?
Click to expand...
Click to collapse
Can you please post the contents of your startup.txt?
Thanks!
hi there
i just managed to install android onto a HTC "Kaiser" TyTn2.
everything i need seems to work fine except sound and wifi.
i installed RLS15 from http://forum.xda-developers.com/showthread.php?t=759894
using KaiserCustomRUU.exe
now there seems to be no sound. i called a number, and i hear nothing at all. i tried pressing speaker, and same no sound. vibrates working though. i also tried pulling the vibrate tab but it didnt work. still no sound.
about wifi, i have a Ad-Hoc network from my computer (which i can connect to from my ipod touch 3g - iOS4), but even after turning Wifi on in settings, it just doesnt seem to see my network....
btw i got no "welcome to android" or set up or anything... i did hold the DPad
any help?
I'm not sure but try out another Radio http://forum.xda-developers.com/showthread.php?p=9807696#post9807696 <---- Here
Flash it with HARDSPL or just using CustomRUU when in the tri-color screen.
I could be wrong but that's what I'm guessing
Wi-Fi... Wich kernel did you use?
Try out http://forum.xda-developers.com/showthread.php?p=9807696#post9807696 Post 118
And use the Androidupdate I attached, It's the one from Liquid wich should fix the Wi-Fi
Let us know if it fixed it
(God i had to edit it a million times before i did it right )
calls do definately go out. i called someone, i coudnt hear anything, and they called me back.
What do you mean by "Welcome To Android" ?
i read in some website that the first screen when booting android for the first time is Welcome to Android
Gaura Mohana said:
i read in some website that the first screen when booting android for the first time is Welcome to Android
Click to expand...
Click to collapse
In some builds, when you boot Android, it gives this kind of tutorial on how to use your phone (Wich has as title "Welcome to full android on Kaiser" for example), time and date settings and connect to Google account, It's possible that it isn't in the one you use
Don't worry about it, the welcome to android doesn't show when u press D-pad, the D-pad is to get into the menu when ur kernel is booting (the one with black background and white letters)
The menu is to install your system, make backups, clear dalvik and others
ok... but what do i do now about the sound? (and the wifi if posibble)
Gaura Mohana said:
ok... but what do i do now about the sound? (and the wifi if posibble)
Click to expand...
Click to collapse
Sound=New Radio
Wi-Fi is probably androidupdate
[SOUND]
Go to http://forum.xda-developers.com/showthread.php?t=393182
Scroll down until you see this: KAISER Radios These Radios were ripped from Kaiser WM6.1 ROMs.
Pick a radio and download it.
HARDSPL IS NEEDED FOR THE RADIO!
Extract the file and change the name from the NBH file to KAISIMG.NBH if the name is something else.
Copy KAISIMG.NBH onto the root of your sdcard and plug your sd card into the phone.
Hold down the camera button and turn the device on or reset it.
When you see a tri-colored screen, release the camera button.
When you see a blue text with something like RADIO (i guess) press the power button (just 1 little press, no long pressing)
The device will now update your RADIO, when finished just reset it.
Now reinstall your Android version by holding down the D-center button when asked, then selecting Install System and make it clear data.
[Wi-Fi]
Copy the androidupdate.tgz into your Andboot folder
Reboot the phone and press D-center button when asked
Choose the option to install update
Wait for it to finish and just press quit to boot Android
OMG DUDE!! thank you so much
Gaura Mohana said:
OMG DUDE!! thank you so much
Click to expand...
Click to collapse
no problem
hope it works
i just managed to put the KAIS_RADIO_ONLY_1.71.09.01.nbh (which i renamed to KAISIMG.NBH) and i put it on the root after a couple of hours figuring out how to make the phone show up in explorer
i tried starting exactly as you told me, but it boots directly to android - no tricolor. it worked fine before i installed android. so what do i do now?
Gaura Mohana said:
i just managed to put the KAIS_RADIO_ONLY_1.71.09.01.nbh (which i renamed to KAISIMG.NBH) and i put it on the root after a couple of hours figuring out how to make the phone show up in explorer
i tried starting exactly as you told me, but it boots directly to android - no tricolor. it worked fine before i installed android. so what do i do now?
Click to expand...
Click to collapse
I don't think there's another way, just, turn phone off, hold camera button in while pressing the power button once
Release the camera button after you see the colored screen
http://www.youtube.com/watch?v=bVMeZyuIMls
Doesn't show much more than I already said
Did you put hardspl on it anyways?
Thanks... What i managed to do was to simply get into the tricolors by holding power+home, then i connected to computer, and SPL'ed from CustomRUU. it worked, and sound is working. i tried your way but it woudnt detect my .NBH. thanks anyways
but where can i get a androidupdate.tar for the wifi for?
btw quick point, but my camera seems to work!!!! i remember reading that the camera WONT work on android. (it didnt work before installing the latest radio)
Thanks for the file. i just tried installing the liquid update from this post, and all i get is error under wifi (before wifi would turn on - but it kept on searching and found nothing). i did install a old update before this. could that have messed it up?
i also have a problem with USB mounting. I click turn on USB storage, and it works randomly. it works 1 time - doesnt work 10... replkuggin and stuff doesnt work. as in "Android Phone" is showing in Eject, but nothing is showing in explorer
EDIT
-----------------------
I just re-installed android and now installed the liquid update.
NOW wifi turns on, but it just scans (has been scanning for 5 minutes)
my ipod touch sees the network immediately.
Gaura Mohana said:
Thanks for the file. i just tried installing the liquid update from this post, and all i get is error under wifi (before wifi would turn on - but it kept on searching and found nothing). i did install a old update before this. could that have messed it up?
i also have a problem with USB mounting. I click turn on USB storage, and it works randomly. it works 1 time - doesnt work 10... replkuggin and stuff doesnt work. as in "Android Phone" is showing in Eject, but nothing is showing in explorer
EDIT
-----------------------
I just re-installed android and now installed the liquid update.
NOW wifi turns on, but it just scans (has been scanning for 5 minutes)
my ipod touch sees the network immediately.
Click to expand...
Click to collapse
Hmm can you tell me wich kernel you are using? 2.6.32?
Did you use the guide on Atools to make your nbh files?
Guide: http://forum.xda-developers.com/showthread.php?t=783514
Gotta go take exam right now so I'll be looking for this afterwards.
And since it's 06:24 here in the morning, we have a bit of a time issue I think.
I actually dont know what version i have, but i got it from some post on this forum, and it was the latest, and i did use atools.
I found this post http://www.google.com/support/forum/p/android/thread?tid=3b250c94811ca5df&hl=en
I am trying to use a ad-hoc network too, and i dont have any other type of wifi to try.
thanks
good luck with the exams(s)
EDIT- i have 2.6.32.9
Gaura Mohana said:
I actually dont know what version i have, but i got it from some post on this forum, and it was the latest, and i did use atools.
I found this post http://www.google.com/support/forum/p/android/thread?tid=3b250c94811ca5df&hl=en
I am trying to use a ad-hoc network too, and i dont have any other type of wifi to try.
thanks
good luck with the exams(s)
EDIT- i have 2.6.32.9
Click to expand...
Click to collapse
It could be that it's not possible to connect to an ad-hoc network, I've got no idea about that.
Hope someone else will post here and answer that.
U should really try connecting with a normal Wi-Fi network
Go onto the street and look for appartments or houses with open networks just to test?
i live in a small town..... no one here has internet let alone wifi....
aww that's balls
got no idea on how to try it then