OK, so I dropped my phone and the LCD went out, I hooked the phone up to the laptop and the phone still works fine, even the touch screen works. ( I used My MObiler to see phone screen on the pc).
I bought a new LCD screen off of Ebay and replace it, now, the LCD screen works, but for some reason, the touch screen stopped working.
When I took the LCD apart from the touch screen, there seem to be a layer of grease of some sort between the touch screen and the LCD. I wiped it off with a lens cloth, don't know if that caused any problem.
Also there is a dark film (tinted) glued to the touch screen when looking from the back, what is that for? I looked at replacement touch screen on Ebay but none of them have the tinted film layer. I've search all over the internet for instructions but can't find any.
So my question is, what are the correct procedures for replacing the LCD screen and the touch screen (digitizer) ? Also after I installed the new LCD screen, the screen is very reflective and the glare is really bad, how do I fix that problem?
Thank you experts!!
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
bojangle said:
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
Click to expand...
Click to collapse
I went ahead and purchased the digitizer by itself after the original stopped working. Hopefully, it will get my phone back to normal. Thanks for your reply!
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
fone_fanatic said:
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
Click to expand...
Click to collapse
I should have ordered the kit instead of just the LCD. What lead me to order just the LCD is when I hooked the phone to my pc and confirmedthe digitizer still worked. And since this is the first time ever I disassemble a phone, I assumed the two things were separated.
But my digitizer should come in tomorrow so I'll just have to wait and see. Thanks for the info.
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone pad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing my in the car door as I got in....it feel out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone bad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
Click to expand...
Click to collapse
Here's a photo guide of the disassembly of a Rhodium (TP2), it might give you some insight. There's also been a number of threads in this section about hardware parts and the screen/digitizer in particular, listing places where people found/ordered replacement parts.
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
Click to expand...
Click to collapse
The disassembly instructions are here: http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
I did not follow those instructions since I did not want to open the back of the phone.
What i did was I tilted up the phone and used a very small screwdriver and unscrewed the two screws from an angle (it worked).
Then I pried the back of the tilting part of the phone all around to reveal the inside. Be careful not to pull too hard on the flat cable since it's still attached to the back (body) of the phone.
The LCD and touch screen are glued together (I didn't know that before). At this point I would remove the tape that is attaching the flat cable to the back of the LCD, and also lift up the clear yellow tape and detach the three connections.
The widest ribbon is from the LCD, the medium one is for the 4 hard buttons in the front, and the little one is for the touch screen.
I would suggest wearing some sort of anti-static wrist strap (I think I fried my touch screen along with the flat ribbon that is attached to the phone while trying to replace the LCD without anti-static wrist strap).
Once the whole tilting part is freed from the phone, I would carefully push the whole screen (digitizer + lcd) out from the frame, again, they are glued to the frame but can be removed fairly easy.
That's it, the install is reversed of removal and hopefully yours will work again.
Like I said, I think I fried my flat ribbon so after replacing the Digitizer (it came in today), the touch screen still doesn't work, so now I'm looking for that part, I'd appreciate a link to it if anybody knows where to get one.
Oh, and for the parts, just do a search on ebay for "touch pro 2 lcd" or touch pro 2 lcd + digitizer"
Gook luck with your phone!
What tape to use to stick digitizer back to inner bezel/chassis?
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
zedii.co.uk/DSC_0002.JPG
^some of that tape is left on the digitizer... it's the black spongy stuff...
zedii.co.uk/DSC_0003.JPG
^i cleaned (removed residue of sticky tape) in the inner part of the bezel where the digitizer would stick...
Any specific tape to use that anyone knows of?
zedii said:
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
Any specific tape to use that anyone knows of?
Click to expand...
Click to collapse
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
adp9626 said:
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
Click to expand...
Click to collapse
Thanks for the advice adp9626! Well in summary I think I've just been messing about too much and being stupid really.
In the end, I managed to just remove the top part of the screen without actually having to break into the bottom section of the phone.
I was a bit concerned about the whole sticking of the LCD to the Digitizer part. I actually did purchase them separately, however I was not sure what kind of glue was used to stick them both together - as I recall it was a nightmare to try and remove the LCD off the old Digitizer.
So I returned both separate parts (got a full refund as I didn't use them) - and now I am looking to purchase both parts stuck together.
I'm waiting on the guy on eBay to confirm that they are both stuck together. I'm also thinking of using double sided sticky tape to stick the Digitizer back to the inner bezel...
So that's the final plan! I've been a bit silly in rushing with ordering parts etc. but I just want to be on the safe side now - well - at least with the LCD stuck to the Digitizer part.
I will take your advice on the gel superglue if the double sided sticky tape doesn't prove it's stickyness!
Thanks
Zayd.
Can anyone help me find the lcd screen and digitizer as a single unit for Sprint? Everyone I find states not for CDMA.
Thanks
Anyone ??? I spent an hour on google and still came up with no leads.
hyghlndr said:
Anyone ??? I spent an hour on google and still came up with no leads.
Click to expand...
Click to collapse
I ordered one from this guy and it works great. it comes with the entire top half of the phone and the keyboard. There is only one left so you may want to hurry. Link: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&Item=270583335455&Category=20336&_trkparms=algo%3DLVI%26its%3DI%26otn%3D2
Edit: I wanted to add that they're are slightly used so there will be scratches. The one i received is a little more scratched than my original then again the scratches aren't noticeable when the back light is on and you're getting a working screen.
Just my experience, I had a faulty LCD, digitizer was OK. Bought a replacement LCD off ebay, delivered from China but only cost me £20 inc delivery. Arrived with tools as well (T5, T6, philiips, and pry tool). Followed a couple of disassembly instructions online, took me a while to get all apart but managed it. None of the instructions online go through actually taking the screen out, I thought I'd messed it up as I took the back half of the LCD off and left the front bit on, and I couldnt get it off at first. I ended up using a very sharp scalpel to slide between the LCD and digitizer and got them apart eventually, as I didnt realise that they were glued.
Anyway, I just placed the screen on, no glue as there is a ring of sticky tape around the back of the digitizer which holds the screen in. Connected everything back in the end and its working fine. Only prob is I think I damaged the power/standby button, so be careful when around this area.
Touch Screen not responding after replacement
Recently, I replaced a glass screen on a SGH-M919 Galaxy S4. Previously, during the process of cleaning the glue residues off the LCD screen; I rubbed it with rubbing alcohol and it removed a small streak of the adhesive glue off left side of LCD screen and bottom right corner. After installed the new glass screen, I noticed a few spots of the glass screen wasn't sticking onto the sticky layer. So it looked like it has big air bubble between the glass screen and LCD. And I could see the rubbed off streak on the LCD screen. Everything worked fine with the new glass screen, with the exception of seeing the streak and bottom right corner rubbed off.
A few days ago, I had a table clock fell on top of the phone and broke a piece of glass. Nothing happened to the LCD screen and still functional 100%. So I got a replacement glass screen - the same as the first time replacement. With noticing of the rubbed off streak and corner of the adhesive layer on the LCD screen - I decided to rub off all of the adhesive layer from the LCD. I sprayed some Goof Off liquid on the adhesive layer and left it over night. Next morning I continued scraping off the glue with a small plastic card. Cleaned off all glue residues and examined the LCD screen for any scratches or damage. There was none. Re-installed new glass screen - but now the touch screen does not respond to the touching on the icons. Only the Home, Menu & Back touch button work. I was baffled after this.
Could it be that because I left some the Goof Off liquid on top of the LCD screen over night and it might have leaked to the other side and shorted out something? I saw a few forums that suggested a Factory Reset. I did that - but still didn't work. Please advise on what I need to do to fix this problem.
Thank you in advance for the advise or suggestion.
So you know that these are the TP2 forums, and no one has used this thread in the last 3 years....right?
LCD digitizer replacement.. now black screen
I saw the for replacing the LCD-digitizer of my nexus 4 phone, and followed the steps carefully. After I placed the battery, I checked to see if the phone turns ON and the display is working before I complete the last step of putting the back coverplate. I successfully switched it ON, saw a perfectly working screen, and browsed through my apps. To complete the assembly, I put the back cover by gently pressing the frame along the edges, but suddenly I saw some yellow green lines in the middle of the screen. I switched it off and again switched in ON, but now the entire screen had light with no display.
To fix this, I tried again checking all connections but no luck. What could be the reason for the sudden loss of display when it worked perfectly fine moments ago? Is there a possibility that I damaged the LCD while putting the back cover on the phone?
I am also not sure about one of the ribbon connectors of the digitizer. There are 2 big ones which are prominent and has ports to connect. However, there is a little third one which also has to come through the gap but doesn’t connect anywhere. Has anyone also experienced this while replacing the screen? Any help will be appreciated.
Right so long story cut short, my beloved Desire has decided to stop working after being dropped from a small height by a friend, the glass has cracked, the LCD is bleeding, while the digitiser seems to work fine still. Is there anywhere recommended that will replace it for me? Or any decent site selling OEM parts?
Cheers
i have also had an accident with mine. the lcd screen seems to be ok but the glass cover cracked in a million placed. took it to a few repair places and are all pretty confident it can be fixed. only problem is the parts for the phone are not out yet as its so new. have been told it could be up 2 a month. contacted htc but they cant give me a quote, i have to send it to them first.
bump, might take a few pictures of it for your entertainment
Sounds like your friends owes you a new Desire!
Cracked Screen... ME TOO!
I too have had the unfortunate displeasure of seeing my brand new desire drop to the ground on my tiled floor bathroom and land in just the right position fo the screen to crack. Have insurance but as I had just that day switched to a new phone and contract with orange hadn't switched the IEMI number over with my insurer. Long story but didn't realise I had to switch as I have never claimed AS THE INSURANCE COMES WITH MY BANK ACCOUNT NEEDLESS TO SAY INSURANCE DOESNT COVER IT FOR 15 DAYS AFTER YOU REGISTER THE EMEI NUMBER OF THE NEW PHONE... so beware folks honest isn't always the best policy and sometimes having insurance with your phone provider can be a better option!..
No new screens available from any UK repAIRER YET SO WILL HAVE TO WAIT IT OUT WITH A HALf visible (but still working) screen.
I just joined your club.
I dropped my desire just 15 minutes ago onto some concrete stuff.
The glass screen is totally obliterated.....but the phone still works.
So 2 questions.
- Can I but just the glass part and replace it ? the underneath screen is ok
- How much can it cost ? ( if it's possible in europe...if not in canada or usa)
Both display and digitizer can be currently found on the internet, they're not cheap though...
http://www.dealsniper.com/en/home/2563-htc-desire-glass-touch-screen-digitizer-replacement-7.html
http://www.iphone-spares.com/htc-parts/desire-lcd-screen-google-g7
They say LCD, I'd say it's a mistake, not sure though.
Are you kidding?
If it's just 60$ then it's very very cheap......
I will try to buy it.
Ps:
read this : http://tjworld.net/blog/htc-desire-tear-down
it's a photo tear-down and re-assembly guide on how to replace the broken glass digitiser
howzit guys
i see on the net that theres a new desire coming out and its got a lcd screen coz of the bad visibility in sunlight of our amoled screens
where can we get these lcd screens - mayb its better to fit a lcd onetime instead of amoled again
I also have a broken display.
And last week I ordered a new one on ebay. I got it today, but when I installed it, it wasn't working. Only a faded green light on the right side of the screen.
The phone booted ok (vibration at the beginning and the sound when it's booted - pin request).
Then I took the new screen out and began an close inspection. I was amazed that I found a freaking hole in the display (the original does not have one, obviously).
shrani.si/f/e/rz/25HpVJoS/p3300153.jpg
shrani.si/f/3V/tE/4hMdL00g/p3300154.jpg
shrani.si/f/1X/35/FLeujkL/p3300159.jpg
(there is an tireless w810i behind the screen with led on, u can clearly see the light shining through the display)
I'm going to send the pictures to the seller, and see what he says about it..
Anyone had similar experience? Or any explanation about the holes? (there actually two, second one is right on the edge, can't take a photo of that one..)
I have hardware version 0003, the display works fine just the top glass got cracked, can someone point me in the right direction for a new digitizer assembly? I found one on amazon new for 24$ but have no idea if it will work for my phone.0002 vs 0003 I read have different ribbon cables.
Sent from my EVO.
When this happened to me, I couldn't tell that the LCD had also cracked. I bought the digitizer only, and when I took apart the phone, I realized that I didn't have the parts I needed to fix it.
I can tell you that the correct P/N for the Novatel screen is 2V6A, but I am not sure of the P/N for the Epson screen. Check which screen you have by adjusting the brightness.
If when you adjust the brightness it switches with a fade effect, then you have a Novatel screen and you need the 2V6S ribbon. However, if it switches quickly and suddenly from one brightness setting to the next without a fade effect, then you have an Epson panel and you need the other ribbon cable.
So, I know it's been posted a lot in other places but I couldn't find like, a definitive answer as to if there are different digitziers? Am I just confused?
I would like to try and just replace the digitizer and glass over top of the LCD, my LCD works fine, the cracks are really thin and only a few going across diagonally. It fell from maybe 2 feet off my lap onto a parking lot surface.
I understand there is two LCD pannel types like you said, but are there two digitizer types/sizes?! for that ribbon cable.
I'm completely comfortable with taking it apart, I'm just worried I'll get the wrong part and find out the screen is also cracked and have to end up not using it for days until new stuff ships.... bleh
I've found digitizer+glass on amazon for 24-30$.
How do I adhere it to the LCD though, says doesn't include anything to do that.
EDIT: Found this gem: http://www.durapowerglobal.com/HTC-EVO-4G-Digitizer-Adhesive-_p_1166.html
Adhesive wont be a problem I just need to know about the glass/digitizer
EDIT2:
OKAY, if you want to ignore all i've said so far here is my real question of what I need to know.
http://www.durapowerglobal.com/HTC-...iginal-With-Installation-Adhesive_p_1103.html
Is there only ONE digitizer/glass piece on any given HTC EVO 4G? Or is there two different types like the LCD?
Dropped my phone on asphalt today and got a big hairline crack across the screen . (Attached pics)
It really hurts cause i always baby this phone and just the rush to get to work and in my car, completely missed my pocket.
The screen is still responsive to touch and seems to be working normal thank god the lcd screen wasnt damaged and the digitizer didn't shatter.
Got a few questions t
1) just wanted to clarify that the digitizer lies ontop the LCD screen?
2) and that is all that needs replacing?(from damage seen in the pics)
3) also mine is branded just HTC(no carrier, so it's international GSM version?)
4) would it matter if i bought a replacement digitizer meant for the at&t version or not?
5) should be getting a one x that had some water damage and is no longer working. would the digitizer from this phone be a viable option for me to use as a replacement or should i just order the part online.( I really want it replaced fast and if i have to order the replacement it will take about a week to 2 weeks to arrive in my country
so apparently i can't attach any urls until i make 10 posts or i'd show u guys the part i wanted to order but its basically just a screen digitizer from ebay with tools needed for about $17.86.(is that cheap, good or expensive price considering the item + tools)
can you guys please search for it on ebay?the title of the post/part is Touch Screen Digitizer Glass Lens Replacement For HTC One X S720 + Free Tools
the link above is the item i'm looking to order for replacement. is it the right part i'm looking at?and would that be all i need or is there anything else i should add?also quality wise would it be top pick or are there any better options available?
Attached some pics also.Advice would be greatly appreciated.
You are unlikely to be able to separate the digitizer and lcd without damaging the LCD.
A water damaged phone may have a water damaged screen.
Search one of the other broken screen threads for more information.
I've replaced several screens on captivate.easiest way is get replacement(LCD+digetizer) from ebay,Google procedure.watch or read as many times as needed to feel confident to take apart phone.the hardest part is seperating LCD from phone(they use adhesive to secure LCD to phone).I used razor to carefully cut adhesive.
Most components are plug&play.just follow guide completely,u should be fine.
My LCD was $85 on ebay.good luck.
Sent from my SGH-I897 using xda app-developers app