[Q] Blown Ear Piece Speaker - Droid Incredible Q&A, Help & Troubleshooting

Not sure how i pulled it off, but my ear-piece speaker (the one used for calls) is blown. My warranty is expired so I am thinking of attempting to replace it. I searched around the forums and didn't find much on the issue except for replacing the external speaker. I did a little searching on google and found this . My question is: has anyone else tried to replace it? Is it very hard?

It is very simple! Pull the back off the phone, then pull the battery. Pull the 4 screws on the corners, lift a corner of the red back and release the black tabs as you apply pressure then the red back will pop off.
Then pull the yellow stickers off the connectors and release them by lifting the black tabs and pull the wires out. Pull the two silver screws on the top and bottom and then lift the motherboard out and the speaker will be right there on top. Pry it out with a little screwdriver and replace. It really is very simple.
There are plenty of videos on the internet. Just google it.

Related

PDA2K screen slider Modification

Ok everybody, I have taken my PDA2K apart & fixed the wobbly screen problem, First things first:
1. get a sharp knife & carefully slide it under the VOID sticker moving upwards very slowly,& you should be able to remove the sticker in one peice,I have done 7 units ok so far.
2. remove three black screws from the battery compartment,& the silver countersunk screw from underneath the now removed VOID sticker,
Then the 2 countersunk screws from the top sides of the PDA2K,now the rear cover can be removed.
3.Three screws hold down the main PCB,looking from bottom of unit,one screw very top right corner of PCB.One screw Very top left corner of PCB.
& one screw half way down on right side near the ribbon cable for the key board.Then remove the yellow tape over the keyboard ribbon cable,Then lift the black clamp on the ribbon cable connector upwards,and put a round diameter screwdriver under the ribbon cable & pull outwards in a straight direction.
4. Extend the screen fully open & carfully lift the PCB up from the left side (OPPOSITE) the keyboard ribbon cable connector,& hold it slightly up as you carfully slide a blunt flat Knife under the 2 ribbon cables for the display.They will just pop off with minimal force.
5. Pull out the vibration motor & microphone from their casing slots (NOT PCB CONNECTORS) & place the main PCB in a safe place.
6. Looking at the back of the front section you should see 2 screws through slots in the back casing,& 2 at the top rear of the display.remove these & lift the display up from the bottom,carefully guiding the 2 display ribbon cables through the slot.
7. You will now be able to see the sliding plate edges & the two white peices of plastic at the bottom of the slider,These plastic peices need to come off in order to pull the slider plate up further and off the upper casing.what ever you do DO NOT lever the slider plate up with a screwdriver or the brittle moulded painted clamps will snap.if one does its not the end of the world,the slider plate side can be re-adjusted slighty to compensate.
8. With the slider plate in your hand you need to get a flat (NON SERATED) pair of pliers & carefully & very slightly move the edges of the slider plate outwards on each end so they are not going straight up.ie Looking at the plate from the bottom and flat in your hand the plate will look like a U shape,bend the ends out slightly away from each other so they sit against the slider clamps with more resistance,Be carefull not to over do it or you will end up with a very stiff display,
9. Assembly is a reversal of taking apart but be carefull to guide the display ribbons into the top hole of the slider plate,in its open position,
& make sure to tuck the vibrator motor wiring under the PCB before putting the rear casing on.Also hold the volume slider in the middle position as the rear casing is lowered into position.Remember DON'T FORCE ANYTHING or your beloved device will get damaged .
DONT forget to put the yellow tape on the keyboard ribbon cable & the VOID Sticker back on the silver screw & you will still have your warranty.
I have done this mod on a few units with success every time,& this should have been done in the factory,I find it a shame that comparing this unit to the XDA1 its not got the build quality that the XDA1 has and for £580 its a shame that the hardware is not up to the quality of the software features.
Saying that,I can now hold my PDA2K in my hands without its display moving sideways & it makes me feel im now holding a solid peice of kit worthy of £580.
PS I still have 2 brand new XDA1's for sale & one second hand one ive been using for the last year, 07958031182 Thanks & good luck........... :lol:
hi
any1 who has opened the pda2k .. is the camera soldered onto the mother board or is it only plugged in>???
thanks
Hi the camera is only plugged in,but you have to remove the wifi antenna to remove fom the motherboard.hope this helps.............

black screen

hu. i have a problem. The only thing my htc show is a black screen. the light is on, but nothing displayed. i try to enter bootloader mode but still only the black screen. can anyoane tell me what can i do? i hope is not a hardware problem...
oh, is htc tinity...
If You`re lucky it`s just a loose contact. If You can still hear the sounds from the splash screens I`m sure its nothing worse. Had this too and the fix is really easy once You`ve done it. I had to do it numerous times until I had a good solution. Look in the general trinity subforum, there`s a post on how to disassemble the phone. You have to do steps 1-5 to get the back cover off.
Then You can do an easy test:
- Put the battery back in again. I used some paper cut to size as underlay just to be sure not to accidently short anything should the battery move from its place.
- Hold the phone in such a way that You can apply light pressure on the battery so it stays connected. Now You can power on the phone.
- Apply some light pressure on top of the lcd connection cable (marked red in the disassembly guide) and see if You have a picture again.
- If this doesn`t help try to apply light pressure with a plastic or wood piece from the side where it vanishes in the front cover. In other words play a little bit with pressure direction.
If You get Your picture when applying pressure everything is fine cause all You have to do now is to put in something to polster out the back cover (or side cover, depending on where You pushed from when the screen came back alive). There is a small soft black sticker on the back cover that applies some pressure by default, use this as guidance. First I just rolled a piece of paper and positioned it there when I closed the cover. Didn`t hold for long. Finally I applied a sticker used on furnitures to protect wood floors. Same as vibration dampener stickers for loudspeakers. Just cut to size, stick on top of the old sticker or into the side housing and You`re good to go. Never had a problem with it again.
It sounds far more complicated as it is and You should really try it. I wish You it`s just a loose contact.

replacing screen from zenfone 2 551

Hi all,
i'm very disappointed because i'm just breaking my screen when my zenfone fall of 60cm.
LCD is ok but screen is dead
On ebay i know you can find only the screen with kit, and LCD + screen
Does any one have advice for replacing the screen or screen + lcd? (video or pictures).
Asus France ask me 180€ to change that
thank for your help...
pulesky said:
Hi all,
i'm very disappointed because i'm just breaking my screen when my zenfone fall of 60cm.
LCD is ok but screen is dead
On ebay i know you can find only the screen with kit, and LCD + screen
Does any one have advice for replacing the screen or screen + lcd? (video or pictures).
Asus France ask me 180€ to change that
thank for your help...
Click to expand...
Click to collapse
Seems pretty easy, please check these videos:
https://www.youtube.com/watch?v=qMIivqu6XJY
https://www.youtube.com/watch?v=v4HZt3Aadsc
I ordered a screen replacement on AliExpress. I've only cracked the glass on my phone, but I don't think it's possible to replace the glass on its own. (Unless you have the hands of a neurosurgeon and special equipment.)
Tried changing screen today, but it requires a complete disassemble of the unit. I managed to remove the back and disconnect the components, however I wasn't able to remove the battery since it seems to be glued (?) in place on one side. I even tried using quite a bit of force, but eventually I chickened out since the battery started bending. I have no idea how they do it so easily in the video. If anyone here has managed this disassemble I'd be very interested in getting some details.
dodongobongo said:
I ordered a screen replacement on AliExpress. I've only cracked the glass on my phone, but I don't think it's possible to replace the glass on its own. (Unless you have the hands of a neurosurgeon and special equipment.)
Tried changing screen today, but it requires a complete disassemble of the unit. I managed to remove the back and disconnect the components, however I wasn't able to remove the battery since it seems to be glued (?) in place on one side. I even tried using quite a bit of force, but eventually I chickened out since the battery started bending. I have no idea how they do it so easily in the video. If anyone here has managed this disassemble I'd be very interested in getting some details.
Click to expand...
Click to collapse
Try using a hair dryer on the battery for a minute, but keep moving the hair dryer up and down, to spread the heat all over, this should make the glue soft enough to make it easier to peel the battery off.
Finally managed to replace the screen. This one was really difficult to repair compared to the previous phones I've worked on, but maybe in part because there are no complete instructions out there yet. Lots of glue and tape holding it all together.
The battery isn't really glued, but rather held down by some sticky plastic. (Kinda like chewing gum.) I don't think heating will help here. I used a long, flat plastic object to reach underneath and loosen it from the battery.
I forgot to take pictures, but here are the steps I took. You can find some photos for the first half of the procedure.
Remove 14 screws from the back cover
Carefully remove back plastic cover (double sided tape on center)
Unplug the three connectors going to the top PCB/SoC (these are screen, SIM/SD and battery)
Remove speaker (black piece at the bottom, nothing is holding it in place)
Remove bottom PCB: flip up the little black switch to loosen the connector cable next to the battery, then unplug the wire going to the top PCB, then you can remove it. Vibrator piece doesn't need to be unplugged.
Battery can now be removed, but is as mentioned fastened very well. Try to pull it up on the left side to reach under it.
Unplug digitizer connector on the left side of the top PCB. Just peel off the yellow take and pull it out.
Peel loose the part of the metallic shielding that fastened the top PCB to the surface under where the battery was.
Top PCB can now be removed, start from right side.
Peel off the little "sticker" the digitizer connector goes to. This is probably part of what you're replacing, so it doesn't matter if you destroy it in the process. Otherwise try heating it.
Screen can finally be removed. It's removed from the front of the phone, same as for Zenfone 5. Start at the bottom. It's fastened with glue along all sides. If you're hoping not to ruin the LCD while removing the screen you will probably need a heat gun and extreme patience.
dodongobongo said:
Finally managed to replace the screen. This one was really difficult to repair compared to the previous phones I've worked on, but maybe in part because there are no complete instructions out there yet. Lots of glue and tape holding it all together.
The battery isn't really glued, but rather held down by some sticky plastic. (Kinda like chewing gum.) I don't think heating will help here. I used a long, flat plastic object to reach underneath and loosen it from the battery.
I forgot to take pictures, but here are the steps I took. You can find some photos for the first half of the procedure.
Remove 14 screws from the back cover
Carefully remove back plastic cover (double sided tape on center)
Unplug the three connectors going to the top PCB/SoC (these are screen, SIM/SD and battery)
Remove speaker (black piece at the bottom, nothing is holding it in place)
Remove bottom PCB: flip up the little black switch to loosen the connector cable next to the battery, then unplug the wire going to the top PCB, then you can remove it. Vibrator piece doesn't need to be unplugged.
Battery can now be removed, but is as mentioned fastened very well. Try to pull it up on the left side to reach under it.
Unplug digitizer connector on the left side of the top PCB. Just peel off the yellow take and pull it out.
Peel loose the part of the metallic shielding that fastened the top PCB to the surface under where the battery was.
Top PCB can now be removed, start from right side.
Peel off the little "sticker" the digitizer connector goes to. This is probably part of what you're replacing, so it doesn't matter if you destroy it in the process. Otherwise try heating it.
Screen can finally be removed. It's removed from the front of the phone, same as for Zenfone 5. Start at the bottom. It's fastened with glue along all sides. If you're hoping not to ruin the LCD while removing the screen you will probably need a heat gun and extreme patience.
Click to expand...
Click to collapse
Just cracked my phone. :crying:Thanks for the instructions. Before I decide to do this, are any of the adhesives necessary to put the phone back together?
Yes, order some double-tape for cellphones.
Glad I'm not the only one that succeded althought I scrapped the battery in my case .
I followed mostly the same steps but for anyone that want some pictures, I posted them in another thread
http://forum.xda-developers.com/zenfone2/help/q-lcd-replacement-procedure-t3135165
Can asus ze550ml screen will fit to ze550kl model
@Ptselv: probably best to start a new thread rather than hijack one that is several months old.
And to answer your question: No, a ZE550ML screen will not fit a ZE550KL phone. My suggestion: search AliExpress.com for "ze551kl digitizer" and you'll be likely to find what you need.

Tablet Took a Swim - Volume Rocker Stuck

Good morning;
So, my Nexus 7 took a swim. Fortunately it was a quick one and I was able to recover it quickly and it found it's way into a nice dry rice bath following.
There it sat for a few days until it was nice and dry. Power it on and blammo -- tries to boot into recovery or safe mode.
Fast forward to my best understand of what is happening -- it thinks the volume rocker is being pressed 100% of the time.
So, anyone have any thoughts or suggestions on what I may be able to do? I guess I'll have to buy some sort of replacement part -- but presumably it's not a modular component I can simply replace.
Think I can just 'remove' the volume control entirely?
StabbingHobo said:
Good morning;
So, my Nexus 7 took a swim. Fortunately it was a quick one and I was able to recover it quickly and it found it's way into a nice dry rice bath following.
There it sat for a few days until it was nice and dry. Power it on and blammo -- tries to boot into recovery or safe mode.
Fast forward to my best understand of what is happening -- it thinks the volume rocker is being pressed 100% of the time.
So, anyone have any thoughts or suggestions on what I may be able to do? I guess I'll have to buy some sort of replacement part -- but presumably it's not a modular component I can simply replace.
Think I can just 'remove' the volume control entirely?
Click to expand...
Click to collapse
Just to be clear we're not talking about the plastic buttons protruding on the side of the tablet. Inside, barring some short on the circuit itself or fried components(this you can do by inspecting points of contact on the ribbon, the inside of the connector and the soldering traces at its end), the amber ribbon consisting of power, volume and microphone can be removed from the bezel by very slowly scraping the double-sided white tape underneath it from one end to the other (if you use a thin blade, make sure you insert it between the tape and the bezel and not between the tape and the ribbon itself).
Once out, you will notice that contact is made when the thin round metal plates are pressed together. There are 2 layers. If you again carefully peel off the upper layer (transparent mylar or film), you can see if anything is stuck in between (water or vapor), or that one plate is depressed permanently that it would make contact all the time.
The rest is just a matter of pushing it back to the normal position and realign both layers. Usually, there would be enough adhesive left for them to stick together without your having to add more.
graphdarnell said:
Just to be clear we're not talking about the plastic buttons protruding on the side of the tablet. Inside, barring some short on the circuit itself or fried components(this you can do by inspecting points of contact on the ribbon, the inside of the connector and the soldering traces at its end), the amber ribbon consisting of power, volume and microphone can be removed from the bezel by very slowly scraping the double-sided white tape underneath it from one end to the other (if you use a thin blade, make sure you insert it between the tape and the bezel and not between the tape and the ribbon itself).
Once out, you will notice that contact is made when the thin round metal plates are pressed together. There are 2 layers. If you again carefully peel off the upper layer (transparent mylar or film), you can see if anything is stuck in between (water or vapor), or that one plate is depressed permanently that it would make contact all the time.
The rest is just a matter of pushing it back to the normal position and realign both layers. Usually, there would be enough adhesive left for them to stick together without your having to add more.
Click to expand...
Click to collapse
Thank you for the reply.
Yes, the rocker buttons do continue to rock like a charm. I'll have to crack it open and have a look. Thank you for your advice.

Protip: DIY speaker replacement without voiding warranty (as far as ASUS can tell)

Can't live without your phone for the amount of time it would take for Asus to fix the speaker (again)? Unwilling to void your warranty? Willing to spend €3? Good news: we can work with that.
Buy a new speaker module on eBay for like €3
Wait a few weeks for it to arrive. Yeah, sucks, but at least you still have your phone in the meantime.
Remove the ten screws highlighted in color in this image. (The blue ones actually clamp the speaker down). Critically, you're not removing all of the screws! In particular, you're not touching the one with the white warranty sticker on top of it!
Peel the rear inside cover up a bit, starting from the bottom, just until you can see the speaker module. A couple cm/an inch or so is safe-- the cover will flex. Don't be dumb and snap it off.
Use your fingernail to pop the old speaker out, and slot the new one in its place
Push the rear inside cover back down, replace all of the screws and test
That's it. It's a 3-minute job.
This is one of those "why didn't I think of that" moments!
Sent from my ASUS_Z00A using Tapatalk

Categories

Resources