[Q] I Need Urgent Help ! - Desire Q&A, Help & Troubleshooting

First of all greeting guys,
For some time my phone reboots increasingly more often, and do not know what I can do,
I installed/Flash the official 2.2 Froyo android, but no results.
I have HBOOt version 0.93.0001,
I have tried to make root/reroote, during the process on firtst restart phone it`s still stuck/freeze: (, and the root process not continue.
Please give me a solution if i can do something.
Thanks !

Stock ROM?

Guyz, yesterday i rooted and installed a rooted froyo rom, now the sd card is not detected, even in the recovery, when i researched i found i ve usb bricked! can you please help me with that, emergency pls! and i tried running this command, it says i got to reinstall adb!

dnlgee said:
Stock ROM?
Click to expand...
Click to collapse
before i had Android 2.1 and I did upgrate to 2.2, and it always restarts.
if i hold off 1h,go 15 minutes without reboot
but after 15 minutes always restarts,
when i go in bootloader give me an error :
sd card checking...
etc,
etc,
etc,
etc,
wrong image .............
understand what I mean
there is any solution to make it?

Had a similar issue on my unbranded Desire when I updated an HTC push from 2.1 to 2.2. Some Desire's have to have a Gold Card to properly do flashing
Here's the place where I got the info to do it (probably much simplier methods, but hey... it worked)
http://www.droid-den.com/android-guides/android-guide-how-to-create-a-gold-card
After the gold card, I was able to install a stock version of 2.29.
Hope this helps.

Moscow Desire said:
Had a similar issue on my unbranded Desire when I updated an HTC push from 2.1 to 2.2. Some Desire's have to have a Gold Card to properly do flashing
Here's the place where I got the info to do it (probably much simplier methods, but hey... it worked)
http://www.droid-den.com/android-guides/android-guide-how-to-create-a-gold-card
After the gold card, I was able to install a stock version of 2.29.
Hope this helps.
Click to expand...
Click to collapse
Hi, aim a beginner,can you please help me?
Enter your SD Card Serial (CID) => I do not understand what he mean...

It's a very long identifying number for your SD card.
If you can get to the Market, Download Gold Card Helper like the instructions say.
It will generate the number you need. Follow the instructions on the link I sent.
Basically, you use gold card helper to generate the code. Go back to the link I sent, enter the code on their page, and they will e-mail you an attachment.
Start the hex editor you downloaded from their page, follow their instructions exactly, highlite and paste in the code they mailed you. Save, and you have a gold card.
Above all, follow their instructions TO THE LETTER.
Oh, one more thing, to get the links to download the program you need, and to enter the code that will be generated, just run your mouse over their text, it's all in blue color, so is difficult to see the links.

Related

Which chip store the Bootloader and the WinCE ?

Dear XDA Developers #... and all other experts,
I had a T-Mobile MDA and I'm affraid that my bootloader had problem with all the buttons. The bootloader V5.15 boots and show GSM OK but none of the action buttons working ? Any Clue ?
Is the Intel #3204C 32MB Flash Memory chip store the bootloader and the WinCE because I had some technical guys who be able to clone the chips using some clonning machine.
Please advice as my MDA had been down for 2 weeks.
Thanks in advance
I would guess you have a hardware problem with the buttons.
Did flashed with SD card but checksum not correct
Dear Peter Poelman,
I did flashed with SD Card 2 weeks ago. Using the XDArit (old ver) and with O2 3.14.13 Rom. I did many restored but everytime it said restored completed but checksum not correct.
I did managed to see the O2 boot screen ( Blue O2) showig 3.14 at the right bottom of the screen but not be able to load the WinCE.
Is there a limit or counter that say number of times SD card restored ?
You think is hardware problem, any solution ? If you think where the fault is, maybe I be able to ask a Technical guy to open the MDA and repair it.
It is not possible to find any T-Mobile support around Asia.
Any respond would be much gratefull
Question: how big was the SD card you flashed with? (It has to be 64 MB minimum if you back up OS and bootloader at the same time.)
I would use XDArit to write an SD card (32 MB card is ok) that contains only the WinCE (OS) part, and try to flash from it. If your card is somehow corrupted, you can use XDArit to read from the OS from the Special Edition nbf-file inside Jeff's exe-file, which you can extract if you open the exe-file with WinZip.
Is there a limit or counter that say number of times SD card restored ?
Click to expand...
Click to collapse
They actually built such a mechanism for bootloader 5.17, but gave up on it (maybe after is was cracked by us?). But this really does not apply to you as you probably do not have this bootloader (or you would not have been able to make a backup).
Bootloader doesn't kick start to restore ?
I am using a 128MB SD Card.
Now even I wrote the SD Card with the new SER 1.1 .nbf files and insert the SD card into the XDA, Bootloader boots up but it doen't show the screen that say press action buttons to start restore ? It only show Wallaby Bootloader v 5.15 and freeze....
I am afraid that the bootloader on the XDA might be corrupted as well. Any tips or solution for these problem.
I remember reading in this forum saying that the XDA be able to lock all buttons accept the Power button. Seems like my case, the Power buttons, soft reset and hard reset buttons working only, the rest are not functioning. The XDA are still be able to charge on the craddle and the power worn off quite fast. Sometimes I even be able to see the Phone Cancel Buttons ( Red one ), the red light are always on...
Any help would be much grateful
suajw
Re: Bootloader doesn't kick start to restore ?
suajw said:
Now even I wrote the SD Card with the new SER 1.1 .nbf files and insert the SD card into the XDA, Bootloader boots up but it doen't show the screen that say press action buttons to start restore ? It only show Wallaby Bootloader v 5.15 and freeze....
Click to expand...
Click to collapse
You used XDArit to write the card, right?
You need to describe in much greater detail what you do for me or anyone to be able to help you.
I'm having a T-Mobile MDA in 3.13.12 GER ( 09/16/02) Radio T310
Bootloader v 5.15 and trying to flash O2 3.14.13 Eng Rom :
1. Using bootloader backup Boot+CE to SD Card.
2. Using XDArit (old ver) Read SD and store to PC ( WinXP )
3. Run RSU-eng of O2 Ireland, sucessfully upgrade, GSM no problem.
4. Run RUU-eng of O2 Ireland, Rom Image not found, error 007.
( forget to patch the NK_wallaby31413wwe_o2Full.nbf )
5. Decided to use XDArit (old ver ) to write Boot+CE ( O2 3.14.13).
6. Insert SD Card into MDA, flash restore compeleted but said checksum not correct
( Repeat many times of writing using XDArit (old ver), sometimes CE only but still checksum not correct )
7. Few occation, manage to see the O2 boot screen showing 3.14 but freeze
8. Left the MDA for few days and try the writing using XDArit again
9. Now soft boots, Bootloader boots show GSM OK, but none of the contact, calender and volume buttons work. If there is a SD card in the MDA, bootloader boots show v 5.15 but not be able to read SD Card.
( some of my posting are on Rom Upgrade forum under suajw)
Just to let you know all the about was done before the release of your SER v1.0 and v1.1 and the new version of XDArit v1.02
The MDA still be able to charge the power but will discharge if leave over night.
Any help will be much gratefull
InitDebugSerial can load bootloader+CE ?
Dear Peter Poelman,
If i boot the bootloader in a serial port from a PC using Hyper Terminal, do you think i be able to load the Bootloader+CE from a SD Card using the comand :
c2r ( from your Wallaby Bootloader Page )
Please advice and many thanks in advance
Notes : have not try using serial port to talk to the XDA
Good idea. Try and see, I guess.
Try hooking up the XDA to the serial com and it still not be able to communicate with XDA, even ? <enter> doesn't show any respond.
What could be the problem ?
By the way Peter Poelman, which is the chip that store the Bootloader+WinCE, I might need to ask someone to clon the chip for me from another XDA.
Thanks for your help and time
Still waiting for reply ????
Dear XDA Developers #.....,
I am still waiting for some replies in this matter....
Any info and advince would be grateful, Thanks.
Re: Still waiting for reply ????
suajw said:
I am still waiting for some replies in this matter....
Click to expand...
Click to collapse
Can't speak for anyone else, but to be honest, I have no idea what your problem could be. It's something odd, and looking at the steps you performed, my first guess would be that it could be hardware related.
Did you try a different SD-card? 64MB or bigger (when doing BOOT+CE, 32 MB or bigger for CE)? A different SD-card reader/writer?
The fact that it first reported checksum error and now doesn't read the card at all is funny. Suppose there's nothing wrong with the bootloader that's in there, but that you have some weird hardware problem that messes up communication with the hardware-buttons and with the SD.
Once you tried a different SD-card: maybe open it up and clean the SD-card contacts? (And don't come complaining if you end up breaking it further, it's just an idea...)
Either way: I spent some time thinking about it and replying to your posts. Until new facts surface, I really have no clue what to do in your case, and unless I happen to come accross the same problem again, chances are I will not have a clue two days, two weeks or two months from now. Sorry....
Maybe you can have it repaired?
Good luck...
Still not working....
Dear XDA Developers #.....,
Tried with new SD Card and also clean up the contacts of the SD reader, still not be able to work????
Another thing I notice my MDA, when I boots in Bootloader Mode, after the GSM OK, the 'Phone Hangs Up' button always lighten up RED, is this normal. Is you XDA the same when in bootloader mode. The battery gets drain off easily, is it because the WinCE is not there as well????
By the ways, thank for all your reply and times. You have been a great help for me and I have learn quite a lots from these wonderful web site and forums. Keep up the good work......
I might not be able to find someone to repair the device but hopefully to look up for a secondhand O2 PCB Board to swap to...
Flashing bootloader with jtag?
Dear XDA Developers #....,
Do you think flashing the bootloader using jtag might solve my MDA problem ?
in your //xda-developers/jtag page you mention a patch do be download here.... I don't see the link to download the patches.
Could you please verify.....
Thanks

Help-Artemis locked at startup screen

Hi,
I'm using Artemis with one of Tom's ROM. The device was working well. But today suddenly the device won't start up - it is locked at the startup screen showing the SPL, IPL etc. I can enter the bootloader.
Can anybody tell me how to flash the ROM at this stage?
Flash from bootloader
Hi!
Please download an official rom and keep pressed the Power and Record buttons. You will see a screen with 3 colors (red green blue). Connect the USB cable and wait for Activesync. After this start the original rom flasher and follow the instructions. If you can start the Windows, you should flash the USPL again and you can flash cooked roms. If you flashed a new one, i think you should also upgrade the radio rom.
Sorry for my English
well i'll give it a try.
BTW will activesync work if the phone is not booting up?
sure it will, but make sure you have the only phone pluged in, nothing else, and disable all firewalls and antivriuses.
Good luck
i flashed with htc official rom and it worked first. after soft resetting a few time (due to program installation) the phone again back to earlier state.
it is showing:
ipl 3.13.0001
spl 3.13.0000
gsm 2.94.90
os 3.13.0.0
and stuck at this screen.
i tried to update the phone again with the same rom - but i'm getting error 270.
do i need to unlock cid before flashing?
but i can't use the uspl tool as i can't connect to activesync.
pls help.
make sure the battery is fully charged again.
Restart your PC, isbale ll antivirus and firewalls
Better if flashing in XP PC
put PPC in Boating status
Flash Shipped ROM
Specify which software caused you the trouble and do not install it again
CID unlock PPC
Flash any cooked ROM.
once i flashed the phone with the shipped rom successfully. The phone was CID unlocked then. But now when I try to flash the shipped again i'm getting an error message (error 292 or something - stating-invalid vendor id)
archat68 said:
once i flashed the phone with the shipped rom successfully. The phone was CID unlocked then. But now when I try to flash the shipped again i'm getting an error message (error 292 or something - stating-invalid vendor id)
Click to expand...
Click to collapse
you must unlock phone again.
I tried flashing the device with factory shipped ROM. but i'm getting Error 294-invalid vendor id message.
please suggest what to do?
chance are you have stuffed your bootloader...
start from scratch again by running uspl:
http://forum.xda-developers.com/showthread.php?t=311403
than flash your favorite rom again, ideally via sd-card-flashing:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
greetz
thormdac said:
chance are you have stuffed your bootloader...
start from scratch again by running uspl:
http://forum.xda-developers.com/showthread.php?t=311403
than flash your favorite rom again, ideally via sd-card-flashing:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
greetz
Click to expand...
Click to collapse
USPL needs activesync running. Can you tell me how to run USPL when I can't boot into windows?
well,
its been some time, but i am pretty sure uspl puts your device into bootloader and operates from there...
have you tried setting it into bootloader, connecting via usb and simply starting uspl?
running a normal setup-routine, there is no need to start it from wm either-simply put it into bootloader and start setup!
greetz
Well i tried that. But it seems that USPL doesn't work without activesync.
i've also tried flashing with SD card, but after a brief "Checking SD card content" message the phone goes back to bootloader.
Someone helpppp pls.
are u sure your sd card is correctly configured, according to the wiki entry- especially part "if above fails" ...?
if all steps fail, assumed you performed them correctly, you might try taking out battery and leave the device fully without power overnight...and restart it the next morning
I've used a 512MB SD card - formatted it- and copied the OS file as ARTEIMG.nbh - put the sd card in the phone and started the phone in bootloader mode.
I think there is nothing more to do.
I can enter the bootloader, connect the phone to PC in USB mode. So, I hope that my phone is not bricked.
But how to revive it?
if you are in bootloader, i dont see why you shouldnt be able to flash!!!
try another sd-card, use another xp computer, exchange the usb cable...
yust to be certain: have you left out battery over-night?
...and what are the details stated on boot-loader screen (numbers)?
oh, and I get the feeling you are not working exactly as told:
in your PC right-click on Computer, then select Manage
Select Disk Manager and then delete existing partition
create a new partition with max size 256MB
format this partition in FAT32
thormdac said:
(i)...and what are the details stated on boot-loader screen (numbers)?
(ii) oh, and I get the feeling you are not working exactly as told:
in your PC right-click on Computer, then select Manage
Select Disk Manager and then delete existing partition
create a new partition with max size 256MB
format this partition in FAT32
Click to expand...
Click to collapse
(i) See post no 5 for the details
(ii) You can not do this with a removable disk (SD card inserted through a card reader). Only works when you can get WM5Storage to work.
archat68 said:
(ii) You can not do this with a removable disk (SD card inserted through a card reader). Only works when you can get WM5Storage to work.
Click to expand...
Click to collapse
...i dont have my micro-sd-card-adapter at hand atm., but there sure will be possibilities formatting your sd card accordingly...try administrative tools/computermanagement/storage/diskmanagement under xp, boot your pc with a diskpartitioner like acronis disk director...
i can only advise you to keep trying...but as long as you can not say for sure sd-card-flashing is working correctly, i wouldnt give up...
and as far as flshing bootloader via usb/activesync goes, i can only say i once screwed my device due to insufficiant battery power during sd-card-flashing and thought it was bricked just at the point you are stuck now!!! - totally resetting it with the power-oiut-method, i.e. battery out overnight, revived it!!!
than agin i sure as hell did everything the way it was ment o be done...and nothing worked until i switched to another pc/ usb-cable!!!
so, to sum it up, DONT GIVE UP!!! bootloader is showing...so there must be a way to get this to work...
greetz
archat68 said:
I tried flashing the device with factory shipped ROM. but i'm getting Error 294-invalid vendor id message.
please suggest what to do?
Click to expand...
Click to collapse
Somebody please help me to revive my phone.
how can we help you, if you dont provide us any results of the steps suggested to you...ideally in a way so we can see what you actually did or didnt do, precisely as told ?!?
greetz

[TUT] Unbricking your Excalibur

Everything you ever needed to know about "unbricking" your Excalibur but were afraid to ask is in this guide. I've put together this guide for those of you who either intentionally or unintentionally "bricked" or think you've "bricked" your Excalibur.
It is not easy to brick an Excalibur if you actually read and follow all of the steps and guidelines before a flash. In fact, not many things can go wrong unless a USB cables disconnects during a flash, your PC crashes in the middle of a flash, or you flash a corrupt image file to your device. Statistically, most of the time people only think their Excalibur is "bricked" when actually it's not.
There are three methods you can use depending of the severity of the "bricking". The first method will unbrick 50% of all Excalibur's that have simply "locked up" and won't reboot properly. The second method will unbrick 95% of all Excalibur's that encountered flashing problems or flash failures. The third and final method, and the most involved, is a "last resort" for those who have tried method's one and two numerous times unsuccessfully.
** Please perform these steps and methods at your own risk. I am not responsible for any damage you cause your device using this guide.
If you're new to the Excalibur or SmartPhones in general, please take the time to read the WiKi and this post by Stylez for valuable info before you post or try any of these steps.
http://forum.xda-developers.com/showthread.php?t=397583
http://forum.xda-developers.com/showthread.php?t=537151
But, before I even get into unbricking, if your phone is in fact working right now, I highly recommend you flash HardSPL to avoid even having to follow these steps anytime in the future. The steps and info for HardSPL and JumpSPL can be found in this thread by jockyw2001:
http://forum.xda-developers.com/showthread.php?t=329605
HardSPL basically flashes your phone with an "unlocked" security partition so all security checks are bypassed when you try to flash a cooked ROM or a ROM designed for another variation of the Excalibur such as Dopod, HTC, TMO Dash, etc. Makes life much easier when trying different ROMS or cooking and testing your own! Thanks jockyw2001!!
Ok, so onto the fun stuff... Your phone won't boot... Either it's locked up and simply stopped booting or you flashed your phone and it won't boot. What do you do??
Method 1: Assuming you didn't get "bricked" from a flash problem, the first and easiest method for "unbricking" your Excalibur is (this will erase ALL data in your Excalibur):
(This method works for 50% of supposedly "bricked" Excaliburs)
Remove your SIM and SD card
Remove and reinsert your battery
While holding the two softkeys with your thumbs, press the power button
Continue holding the softkeys until a black screen appears saying "This operation will delete all your..."
Press "'send"' to restore to hard reset your phone
Let the phone cold boot and restore
That didn't work!! . This next method will reflash your phone to the factory ROM.
Method 2: Second way to the path of unbricking is:
(This method will unbrick 95% of all Excaliburs)
Get a hold of your Shipped ROM. You can find these ROMS either in Dopod's site, HTC's site (with a valid serial #), TMO's site (http://www.t-mobile.com/wmupgrade/ with a valid IMEI), or right here at XDA at this post (http://forum.xda-developers.com/showthread.php?t=381726)
Download one of these factory ROMS and unpack it. **Remember, if your phone is a TMO Dash, you MUST use a TMO Dash ROM. If your phone is HTC Branded, you MUST use an HTC ROM, etc., etc., etc...
Remove the SD card if one is inserted in the phone
Remove the battery from your phone for a few seconds. I found this step to be essential to reset the device. Put the battery back in.
While holding the camera button on the right side, press the power button. The phone will enter "bootloader" mode and you will see a tricolor bootscreen.
While in this mode, plug in your USB cable and you will hear the "ba-bing" USB sounds as the device connects
Unpack the ROM package you just downloaded and run RomUpdateUtility.exe. Follow the steps, check the appropriate boxes, and start the flash
Assuming all goes well, your phone will flash to the factory ROM and you can then troubleshoot what went wrong the first time that bricked your phone.
Oh no!! That still didn't work!? Or it worked but the flash failed with Error 270 or another error......... Never fear!! XDA-Developers is here! This next method is a bit more intense. It creates a "goldcard" which is used to SuperCID the Excalibur so that it doesn't care about what factory ROM you flash. Please have the factory (not a cooked) ROM ready to go.
** (This method is not intended for Newbie's and some enhanced knowledge of HTC devices and Windows is required to successfully work.)
** (Retry the second method several times with a few different factory ROMS before attemting the below)
Method 3: The third "goldcard" method is a bit more intensive and should be used as a "last resort" so follow closely:
(should unbrick ANY bricked Excalibur if performed correctly)
Get a cup of coffee or tea
You will need a working Donor HTC device with a microSD slot and a microSD card that is smaller than 1GB (will be formatted) to create "goldcard" image using QMAT tools as described below
You will need QMAT. Get it from http://revskills.de/index.html.
Go to the Download link and download the latest version and unpack QMAT
Have some coffee
Use a SD card reader (either USB for microSD adapter) in your PC to access the SD card through Windows. Format the SD card with FAT32.
* Insert the SD card into the donor HTC device and boot up the device. Connect the USB cable and establish an Activesync connection.
Open QMAT and go to the "Hardware Forensics" menu and select "Generate HTC Goldcard"
In "Select device key:" select the Excalibur
You will need the serial number fro the inserted SD card so click the "Get SD Card Serial from WINCE Device" button
Once the Serial number appears in the box, click the "Save Goldcard Image to WINCE SD" button below
If no errors pop up and all goes well, skip the next step
If you get an error or a popup saying "Goldcard for newer devices isn't implemented in newer devices", you must buy and register the software. Believe me, it's worth the small amount of $ you will spend to bring your expensive device back to life!
Now remove the SD card with the newly written Goldcard image from the Donor HTC device
Insert the SD card back into your PC using the microSD card reader adapter. Browse to the drive letter assigned to it. You will see no files on the SD card, this is normal.
(If, for some reason your PC sees the SD card as unformatted, something went wrong. Remove it and reinsert it into the Donor HTC device. The device should see the card as unformatted and ask you to format it, say yes. Now go back to the "* Insert the SD card into the donor HTC device" step above and repeat the steps)
Unpack your Dopod or other factory ROM and copy RUU_Signed.nbh to the SD card. Once it had finished copying, rename the file to EXCAIMG.nbh. Remove the SD card from the PC.
Make sure the Excalibur is off and insert the SD card
Enter bootloader mode as mentioned earlier (hold the camera button while pressing the power button). No need to connect the USB cable.
You will see a gray screen that says "loading". It will then find the EXCAIMG.nbh file and ask if you would like to start the update process. Follow the instructions and let the phone flash.
It will take 10-15 mins but your phone should boot fine and be back in action!
QMAT is a VERY powerful tool written by viperbjk that allows for full low level manipulation of HTC and WINCE tasks. Read all about it here http://revskills.de/index.html.
Many thanks to jockyw2001 for his amazing HTC device knowledge! Also thanks to all who contributed to this post.
Hope this tutorial helps!
Updates and more info will be here.
What if the phone will not enter bootloader mode?
ookba said:
Updates and more info will be here.
Click to expand...
Click to collapse
Hi OOkba,
This happened to a friend in the office's Dash. It simply froze up while operating. I actually got on the phone with HTC support. We couldn't get it to do anything. It does power up but then freezes.
The HTC guy was of the opinion that it is hardware related.
You ever solved that one?
BTW - I am running the 7.18 6.5 - love it - thank you so much
all steamed out said:
Hi OOkba,
This happened to a friend in the office's Dash. It simply froze up while operating. I actually got on the phone with HTC support. We couldn't get it to do anything. It does power up but then freezes.
The HTC guy was of the opinion that it is hardware related.
You ever solved that one?
BTW - I am running the 7.18 6.5 - love it - thank you so much
Click to expand...
Click to collapse
Thanks, glad you like it. Try this guide for your friend. Sounds like an easy fix unless it is indeed hardware related.
HI OOKBA. I can't find my shipped rom. I have a HTC Excalibur from Digitel, Venezuela. The serial number is SZ702FJ05879. I try all roms and not working. Please, help me. (sorry my bad english)
thank. I formated SD card and insert SD card in to my phone.But Do I need turn on my phone when connect with computer? because when I run QMAT software is error. " could not open connection? Device connected?". Help me. I need help from you
mydreamisrich said:
thank. I formated SD card and insert SD card in to my phone.But Do I need turn on my phone when connect with computer? because when I run QMAT software is error. " could not open connection? Device connected?". Help me. I need help from you
Click to expand...
Click to collapse
Yes, you have to have a spare working phone to create a "goldcard". The phone must be powered on and sync'd via USB so QMAT can access the storage card.
alfatech said:
HI OOKBA. I can't find my shipped rom. I have a HTC Excalibur from Digitel, Venezuela. The serial number is SZ702FJ05879. I try all roms and not working. Please, help me. (sorry my bad english)
Click to expand...
Click to collapse
English is good!! Who is your Carrier? Maybe your carrier has a ROM UPdate on their website? You should be able to use the TMO or Brightpoint ROM. You tried all the factory ROMS and they fail to flash?
ookba said:
Yes, you have to have a spare working phone to create a "goldcard". The phone must be powered on and sync'd via USB so QMAT can access the storage card.
Click to expand...
Click to collapse
I tried turn on my phone. And connect computer by USB but the same error. QMAT can't access the storage card. What does I do?
Sup ookba!
I really want to flash my TMobile Dash using your rom, looks pretty cool but I'm deadly afraid of bricking my phone so first, I took a look on my System Info and it says
ROM Version: 1.33.422.1 (tho its a TMobile Dash, I think the seller flashed it with this international rom).
Model Name: HTC S621
So I got 3 questions
1) Can i flash 3VO rom on this phone?
2) If the flashing fails, can i just use another 1.33.422.1 ROM and reflash it?
3) Will the flashing process (both ways) will bring the SIM Lock back?
Greetings from Brazil and sorry about my glass-cracking, horrible and ultra-bad english.
aletkd said:
Sup ookba!
I really want to flash my TMobile Dash using your rom, looks pretty cool but I'm deadly afraid of bricking my phone so first, I took a look on my System Info and it says
ROM Version: 1.33.422.1 (tho its a TMobile Dash, I think the seller flashed it with this international rom).
Model Name: HTC S621
So I got 3 questions
1) Can i flash 3VO rom on this phone?
2) If the flashing fails, can i just use another 1.33.422.1 ROM and reflash it?
3) Will the flashing process (both ways) will bring the SIM Lock back?
Greetings from Brazil and sorry about my glass-cracking, horrible and ultra-bad english.
Click to expand...
Click to collapse
Yes, your phone is fine. Make sure you follow all of the flashing instructions. Make sure you remove your SD card, connect your phone, run SDA Application Unlock, and run auto.bat from the update package.
mydreamisrich said:
I tried turn on my phone. And connect computer by USB but the same error. QMAT can't access the storage card. What does I do?
Click to expand...
Click to collapse
I dont know what you're doing wrong. Sounds like you're not establishing an Activesync connection properly.
Ok, Ookba. My carrier is DIGITEL and don't have support in the website. The phone comes originally with WM5 in spanish. I try all the factory roms and not working. Please, tell me if there is any solution or I forget the phone.
Thank you any help.
alfatech said:
Ok, Ookba. My carrier is DIGITEL and don't have support in the website. The phone comes originally with WM5 in spanish. I try all the factory roms and not working. Please, tell me if there is any solution or I forget the phone.
Thank you any help.
Click to expand...
Click to collapse
Try the "Goldcard"' method. This should SuperCID your phone and allow you to flash ANY shipped factory ROM. Please follow the tutorial closely. You will need a spare phone with a microSD slot.
Ok, Ookba. But the spare phone must be a same model than mine? (HTC S620)
alfatech said:
Ok, Ookba. But the spare phone must be a same model than mine? (HTC S620)
Click to expand...
Click to collapse
No, just has to Windows Mobile based and have a SDHC slot.
OK. I try with 3rd method and when run Qmat and select "Get SD Card serial from WINCE Device" appears the message "You need to set rigth registry permissions. See QMAT manual for more info." and not recognizes the sd card.
What is the problem?
Thanks, Ookba. You're great, man. Finally someone offers solutions to my problem. Thank you very much. My Phone came back to life again. I make a donation soon.
alfatech said:
Thanks, Ookba. You're great, man. Finally someone offers solutions to my problem. Thank you very much. My Phone came back to life again. I make a donation soon.
Click to expand...
Click to collapse
GREAT!!!!! Congratulations!
I tried but when I click Get SD Card Serial from WINCE Device in the box none found and click Save Goldcard Image to WINCE SD is card ID isn't 16 bit (32 charter) long. I isn't succesful. help me???????

HTC desire 2.2 HELP please

Ok so, this is my first android phone and after being prompted to install the 2.2 update on my European htc desire, i downloaded and started it installing. It gets to about 23% and says process system unavailible and after reading what people said i cleared the phone and tried to install the update manually from the SD card. This didn't work
My phone currently does this
Will boot into what it says is 2.2 but with no wifi, no service, and no SD card showing up
then after about 5 minutes it will reboot.
I have no idea what i can do to fix this? could someone please help me, i'm a noob with android so a clear step by step would be much appreciated
anyone
I am having the same issue... Anyone some help please...
I had a symetrical experience.. I can't post links yet, but you if you look at my posts you should be able to find what worked for me.
Futurian said:
I had a symetrical experience.. I can't post links yet, but you if you look at my posts you should be able to find what worked for me.
Click to expand...
Click to collapse
how did you create a blank goldcard, i can't access my SD card on my phone while it's in the phone so how did you do it
Do you have a WIFI connection? I do, and did the OTA 2.2 upgrade over WiFi with no problems, on my Unbranded European HTC Desire.
If youre phone won't boot properly, there are a few answers; 1) Return in to HTC, they're getit working and back to you, 2) Return it to th place of purchase, 3) Root/reflash (but sounds like it might not be an option).
Dale
F3L1X1 said:
how did you create a blank goldcard, i can't access my SD card on my phone while it's in the phone so how did you do it
Click to expand...
Click to collapse
I followed the instuctions in the "[TUT]Complete upgrading guide(root, unroot, flashing ROM & updates)" thread within Desire Android Development. (Post #3)
dedlite said:
Do you have a WIFI connection? I do, and did the OTA 2.2 upgrade over WiFi with no problems, on my Unbranded European HTC Desire.
If youre phone won't boot properly, there are a few answers; 1) Return in to HTC, they're getit working and back to you, 2) Return it to th place of purchase, 3) Root/reflash (but sounds like it might not be an option).
Dale
Click to expand...
Click to collapse
When I got in touch with HTC they wanted £50 to do a reflash, falsely accusing me of rooting my device..
was that 50$ to send it to them? or can they do it without having it there. Because if THEIR update screwed up my phone i don't see why i should have to pay for a fix
maybe a silly question but did you try a factory reset?
http://www.htc.com/www/howto.aspx?id=805&type=1&p_id=312
HugoTouchHD said:
maybe a silly question but did you try a factory reset?
http://www.htc.com/www/howto.aspx?id=805&type=1&p_id=312
Click to expand...
Click to collapse
yeah i did that, about the only advice the australian HTC support guy gave me -____-
F3L1X1 said:
was that 50$ to send it to them? or can they do it without having it there. Because if THEIR update screwed up my phone i don't see why i should have to pay for a fix
Click to expand...
Click to collapse
Tell me about it, so thankful I managed to fix it myself!
It sounds like you are alll applying an OTA update for the standard ROM to what was a branded device. There are lots of explanations as to how to fix this if this is the case
In summary
Download update from mentioned here
Copy this to root of your goldcard and rename to update.zip
Turn off phone
Turn on holding down vol down
Select Bootloader then Recovery (an image of device should appear with exclamation mark over)
In menu (sorry forgot how you get in, if it does not appear then try power+vol down or power + back). From there choose apply update.zip
Wait while update applied
After update select reboot and wait for device to boot
Video of it here
jameson_uk said:
It sounds like you are alll applying an OTA update for the standard ROM to what was a branded device. There are lots of explanations as to how to fix this if this is the case
In summary
Download update from mentioned here
Copy this to root of your goldcard and rename to update.zip
Turn off phone
Turn on holding down vol down
Select Bootloader then Recovery (an image of device should appear with exclamation mark over)
In menu (sorry forgot how you get in, if it does not appear then try power+vol down or power + back). From there choose apply update.zip
Wait while update applied
After update select reboot and wait for device to boot
Video of it here
Click to expand...
Click to collapse
I've just tried this again, installation looked like it went through ok, rebooted and relaoded into sense, then it shows me a status bar counting, normally this gets to about 10% then says ?Sorry process system is not responing, so i can either click wait or force close, then in continues upto about 97% then reboots and reloads only to load a white screen showing htc and continues counting in percentages, gets to about 15% then says force close, then onto about 91% then reboots this goes on for a while until it just shows me a sorta bricked phone with no wifi, gsm or any real functionailty and it continues to reboot every 5 mins, back to where I started showing 2.2 as installed
One strange thing I have noticed is that my CID is
CID: 00000000000000000049E917D100A69E
Reversing CID
CID: 00A600D117E949000000000000000000
Can't find update.zip on SD card during recovery
Tried all this, thanks. Goldcard created using Gold Card Tool 0.0.5 (awesome job Klutsh) . I get the error message:
"E:failed to open /sdcard/update.zip (No such file or directory)" even though it is in the root dir when I look at the card on my PC.
Should it be in a directory called /sdcard ?
chessmaster82 said:
I've just tried this again, installation looked like it went through ok, rebooted and relaoded into sense, then it shows me a status bar counting, normally this gets to about 10% then says ?Sorry process system is not responing, so i can either click wait or force close, then in continues upto about 97% then reboots and reloads only to load a white screen showing htc and continues counting in percentages, gets to about 15% then says force close, then onto about 91% then reboots this goes on for a while until it just shows me a sorta bricked phone with no wifi, gsm or any real functionailty and it continues to reboot every 5 mins, back to where I started showing 2.2 as installed
One strange thing I have noticed is that my CID is
CID: 00000000000000000049E917D100A69E
Reversing CID
CID: 00A600D117E949000000000000000000
Click to expand...
Click to collapse
i get this same problem. How do i create a gold card if when i plug in my phone to my pc it won't recognise it and when i put the SD in the phone the bricked 2.2 won't recognise it
F3L1X1 said:
i get this same problem. How do i create a gold card if when i plug in my phone to my pc it won't recognise it and when i put the SD in the phone the bricked 2.2 won't recognise it
Click to expand...
Click to collapse
I had to format the card in a card reader in my PC, then use the Gold Card Creator mentioned elsewhere in the thread. You have to install HTC Sync because enough drivers are in there to at least allow the apps to 'see' the card at physical level, even if the bricked Android doesn't. Set the phone to USB debug mode in Settings/Applications - the phone stays 'on' long enough between reboots to do that and get a CID out of it! Then Gold Card Creator works well enough to get the CID from the SD.
I'm trying this again with a 2GB card to see if makes any difference.
Check folder settings when using windows
bearMedicine said:
Tried all this, thanks. Goldcard created using Gold Card Tool 0.0.5 (awesome job Klutsh) . I get the error message:
"E:failed to open /sdcard/update.zip (No such file or directory)" even though it is in the root dir when I look at the card on my PC.
Should it be in a directory called /sdcard ?
Click to expand...
Click to collapse
Quick update to this. Make sure you have extensions of known file types SHOWING in your folder settings. I was naming the file update.zip.zip!!
Thanks to ALL in this forum for get apps and assistance. I unbricked my phone tonight thanks to you all
well i phoned the shop here in australia that i bought it from and they said they've had alot of desires being returned because they've been bricked by the update and to just send it back and they'll fix it and update to 2.2 for me

[Q] Downgrading DHD using AAHK

Hello ,
i bought my DHD few days ago , it is shipped with the last GB update , Android version 2.3.5 , Sense 3.0 , software number 3.13.415.2 ...
i know how bad that looks , cuz rooting the GB shipped dhd seems to be pain in the ass ...
i started to look for it before making a new thread, i found 2 solutions , AAHK and HTC DEV TOOL .
starting with htc dev tool , i read that it has many disadvantages , and a lot of custom roms wont be able to be flashed after using this method in rooting , so i decided to choose the AAHK which seems much better , but i faced a major problem , the downgrading of the dhd ...
i started to root using AAHK , did every thing was written in the notes ,disabling av , installing drivers , usb debugging ....etc
1- connected the phone
2- pasted the password
3- pressed 1 to start hacking
4- i was asked to downgrade , i chose yes
here comes the problem , cuz the aahk started trying to download the PD98IMG , it completes 20 try then stops .
i took the link of the PD98IMG , and downloaded it myself , its a zip file sized 256 mb ... i put it in the file that has the same name in the kit , and started over again , nothing happened .... pasted it to the sd card and started again , nothing happened also , and the kit tries always to download the PD98IMG with no result .....
did i make any mistake ?
did i miss a step ?
any help will be appreciated , thanks in advance
it's not a big deal... just take the downloaded ROM "PD98IMG.zip" and copy it to the root of your SD card, then go to hboot "turn off the phone and then start it with power+vol down " it'll take you to the hboot menu " white screen with few options " it'll scan your sd card and automatically prompt you that if you wanna install the discovered ROM or not, choose yes and you must be ready to go.... hope that what i said is helpful and guys correct me if I'm wrong..
if i helped please press the thx button
SpiritStealer said:
it's not a big deal... just take the downloaded ROM "PD98IMG.zip" and copy it to the root of your SD card, then go to hboot "turn off the phone and then start it with power+vol down " it'll take you to the hboot menu " white screen with few options " it'll scan your sd card and automatically prompt you that if you wanna install the discovered ROM or not, choose yes and you must be ready to go.... hope that what i said is helpful and guys correct me if I'm wrong..
if i helped please press the thx button
Click to expand...
Click to collapse
thx pal , the problem was in "PD98IMG.zip" downloading step because of the internet proscription in Syria , i used a proxy bypass software and everything wnet perfect ... it took some time to download the image but it deserves waiting .... lol
ghassan haddad said:
thx pal , the problem was in "PD98IMG.zip" downloading step because of the internet proscription in Syria , i used a proxy bypass software and everything wnet perfect ... it took some time to download the image but it deserves waiting .... lol
Click to expand...
Click to collapse
mine transfers the file to sd card but hboot wont show any option to press the volume up key to start the downgrading process please help
looks like you have a problem with downloading the downgrade ROM due to your slow internet speed?
I suggest that you should download and install this stock rom
___h t t p ://shipped-roms.com/download.php?model=Ace&file=RUU_Ace_TELUS_WWE_1.84.661.1_R_Radio_12.35d.60.140f_26.06.03.24_M2_release_168987_signed.exe
This is an old stock rom but it will make the AAHK be able to root without downgrading the ROM. Since the link above is a direct link, you can add it to any download manager which can accelerate your download speed. It is faster than letting the AAHK download the old rom by it self.
Hope this help
Can anyone tell me how to install the driver correctly from the AAHK pack. I go to tools then win and install from there. Then I run the program and it gives an error message. Can anybody tell me what seems to be the problem. Thank you for your help guys.
What is the error message ?
Are you talking about the adb drivers ?

Categories

Resources