Dear Fellow Forum Members,
Followed instructions as per Xda_II_Upgrade.pdf, during installation got to a section where I got a message saying that the current rom is being erased a task bar was displayed which increase's in percentage as the job goes through. However the job was still at 0% completion when an error message was displayed saying the job had failed and the device needed to be undocked and a soft reset performed and then re-docked and to restart the process again. After performing the undocking of the device and software reset I get a message on the screen serial V1.0.1 when connected to the cradle the message changes to USB 1.01 and I cannot do anything else the unit does not boot into pocketpc, as you can imagine this is very frustrating as I depend on my xda2 to receive and make phone calls I would be very grateful any members know of any way to get around this problem. I must say I am a bit concerned a try and tested xda2 update has led to this problem.
Just run the update .exe file again with the XDA docked and it should just install the update again. It happened to my mate on Saturday with his XDA II and he just ran the program again.
Dave,
done as you said and all went thru fine you are a star thanks mate.
No problems it's good as a newbie to be able to actually help people.
upgrade xda2 rom ver 172187 dead os--connection error
i was trying to upgrde the rom from o2 website when error occured at stage 19% completed asking me to reset the xda2 . when i am trying to reset the xda 2 it does not boot it just shows the o2 screen with red letters of the version and does not even charge. my laptop cannot connect to xda2 and as a result i am unable to upgrade when i tried to run the 172187 .exe again it gives error 101: connection error
please help me out of this? thanks
Hi,
I am in the process of upgrading my rom using the rom upgrade from the o2 www site.
Its been stuck on the
'checking the information on your device....Please wait.....Please do not disconnect your device from the PC or power supply until the upgrade is complete'
window for some time now. I dont know if its hung / crashed or in the middle of upgrading.
I dont want to chance it by removing the unit from the sync cradle but at the same time i dont wanna just leave it there for hours if its not doing anything.
Can anyone help ?
Steve
ps - the window I am speaking about came after the big window stating what your current rom / radio stack was and what they would be updated to giving you the option to click 'update' or 'cancel' I chose 'update' and got the message which I described earlier
Try this on a different PC...I'm assuming the phone itself is still functioning.
I had this a while back with the XDA2 and found that by attempting the upgrade on a laptop I had, it worked great without the hang.
I would then remove ASync completely (including registry items) and then reinstall it.
Cheers
Ant
I had this happen, I just shut down and restarted the installer program
Hy guys,
I encounter the following problem with my device:
it generates a file called "DbgToStorageLog" on my root, taking space from my memory (several logs, 2,3 of sizes up to 3MB)... it also generates other files "HTCExceptionLog". The first ones i can't delete (except for one. eg: i have 3 files, i can delet only 2 , one has to remain... message: file is in use), the second type of files can all be deleted... but show up again.
Please help me solve this problem
Many thanks in advance
The way to resolve this is to use notepad and save a blank page as DbgToStorageLog1.txt.
Do the same and save DbgToStorageLog2.txt, then 3, 4 and 5. Do the same with HTCExceptionLo, save as a txt file.
All these saved files will have a size of zero bytes. Select properties on each of the newly saved files and make them read only. and replace the ones of the same name on your device. The files will not increase in size.
Note, you may have to soft resetIf if any of the DbgToStorageLog files displays an error to being replaced...
Brian_bs
Thank you very much... after several days of tring, i nov have 6 files: DBG to storage : 0,1,2,3,4,5 all having a value of 0B ).
By the way, i have another problem.... my screen looses alignment and i have to realign it... sometimes it realignses itself.... this happends when I use several programs at once. Is thi software or hardware fault? Would changing the screen solve it...
thanks in advance for your answers
DbgToStorageLog multiple files
Hi,
I have encounter a problem plz help me problem is,
Form last few days I am testing multiple rom on my device (Xda orbit),with in testing I don’t know when this thing happen which is multiple “DbgToStorageLog0.txt, DbgToStorageLog1.txt …” files created on device root some time one of these file is more then 5mb and my device gone too much slow and some time gone in hang state or some auto restart . I try to solve this problem by doing orignal rom of “O2 xda” but no success .i also tried method of manually created file of 0k size but bettery backup problem remain same means some processing countinously occures for creating that file and waste battery
plz tell me what to do?
Sorry for bad english
Thanks in Advance
In Registry explorer (SKTools) search for key: DebugLog (HKLM\Drivers\BuiltIn\DebugLog\), rename Htc_Lib.dll (delete simbol "_"), change index from 2 to 0. Save and exit SKTools. Soft Reset.
After soft reset - delete all DbgToStorageLog.txt.
In some cooked roms this key is missing. Sorry for English poorly.
Thanks you very very much spgi
after long time somebody response, your solution solve my problem and i am very glad but after doing this my orbit goes too much slow and when i tuch screen it response after 3 to 4 sec and beep trice. So when roll back to previous values "Htc_Lib.dll and index=0" then my orbit give response fast as compared before but start loging files "DbgToStorageLog0.txt ..." again
please give any solution
or if you have o2 orbit and working prefect then give me your "HKLM" registery backup may be this can solve my problem if its possible to import registry of other device
Thanks again for your help
Sorry for bad english
Hi, This problem occurs when GSM data is deleted.
See this post http://forum.xda-developers.com/showpost.php?p=3665608&postcount=52 and follow the steps and maybe this problem will not occur again.I had that and now my device works perfectly. Good luck and I hope to help you.
Thanks a lot "spgi" you have solved my big problem thanks again
helding
Hi again spgi,
As you solve my problem earlier please tell any solution for my problem now
I correct my orbit as u told but after a week my device going in held condition too much and then I doing soft-reset but after some soft-rest its not on even I press power+soft-reset+talk button, but after putting battery out from device for a day then press power button its on and held at boot screen now I can hard reset with official Rom through memory card and some time its success or some time screen fill with horizontal white lines and device goes in not responding mode until i put off battery from device its not off, then same problem of waiting 24 or some time with 5 min its starts. If rom successfully burned then with 10 days same thing happen with my device (helding ). I don’t know what happened to this orbit ,even I used o2 xda from one year and flash lot of rom nothing happened with xda, but orbit give me lot of problem.
Do you have any solution?
I appreciate your response
sorry for bad english
Thanks againg for helping me
Hello,
I have the HP iPAQ 214 device and i'm facing a problem: it is not booting and giving the error: "A problem occured with welcome.exe".
In fact i installed a new calendar application without doing a soft reset after. When i tried to synchronize with my PC, i couldn't do it correctly so i did a soft reset and since the device won't boot. I did already several hard resets and i'm having the same error everytime.
So could you please help me, i've only had the device for 1 week now.
Thanks for anyone trying to help.
1: It MIGHT help if you told us WHAT app in question you installed;
2: As you might also have noticed, or you were just merry-posting, this is the DIAMOND dev corner.
3: The sensible thing to do here, would be maybe to contact the application support (if it's a commercial app); freeware anyways most of the time have community-driven forums too.
hello guys, i need help here
i want to install htc sync, 2-3 weeks ago i installed it and then uninstalled it because didn't need it.
and now, when i want to install htc sync again, it stop and a message came up, here is what the message is:
"The configuration data for this product is corrupt. Contact your support personel."
anyone got this message before?
what should i do ?