(Q) rebooting problems - Desire Q&A, Help & Troubleshooting

hey i have some issuer whit allmost all rom there use ext3/4 i have ext3 partion on an fat32 an linux swap but still it keeps on rebooting when i use gps or camera then it reboot an vibrate 3 times then i have to wait 3 or 4 minute to turn it on again

anybody help

Try a different kernel - they can't be found here.
For people who have lags and/or reboots:
1000mV -NeoPhyTe-2.6.32.28-Halcyon_HAVS.1000_CFS_SLQB_VR_v38
Click to expand...
Click to collapse
You just flash them as the ROM, no wipe.
If that does not help, then do a FULL wipe & re-flash the ROM.

nagypapi said:
Try a different kernel - they can't be found here.
You just flash them as the ROM, no wipe.
If that does not help, then do a FULL wipe & re-flash the ROM.
Click to expand...
Click to collapse
that i have done more than 1 time but no good i have try whit some different rom the same thing i have formatet my sdcard made a fat32 an linuxswap then ext3 1024 mb but the same

I'm not too sure why you keep on mentioning your Ext partitions. I doubt that has anything to do with it.
I'm sorry to say that I am experiencing similar issues. I've tried different ROM's, Kernals, Radio's, etc.
I have a thread I created here. Doesn't really solve the problem though.
Bottom line: Seems like a hardware fault. Take it back to where you bought it from.

Related

[Q] recovery OK, flashing OK, but stuck on reboot

all,
don't really know how I got here, but I don't like it at all ...
I can get into recovery mode as always (clockwork 2.5.0.1) and flash any new ROM I pick up here. but whenever I reboot, my phone is stuck at the white HTC boot screen (I waited up to 2 hours just to be sure it's not my impatience).
I wiped everything (factory reset, cache, dalvik) at least 5 times each. I flashed the latest OD, DeFrost, and Neo ROMs a few times. but whenever I try to reboot, my phone stays forever on that initial white screen with HTC in the middle.
a Nandroid restore of a previously working configuration ends up at exactly the same place!
getting a later version of clockwork seems rasonable? but how do I update that w/o booting up to run RomManager (asked the noob )?
any ideas or suggestions how to fix this?
AtDhVaAnNkCsE
PS. sorry when this has been answered before. but all "stuck at bootscreen" threads I found had the same resolution: wipe, Wipe and WIPE and flash again - I did that plenty of times now...
format sd card and reinsert. be sure to backup important data.
btw wipe-flash-rewipe. post results
after that, try using a sense-based rom, like Pays2.0 or pinky's rom.
Some users find problems with non-sense roms. If you can get a sense rom to work at least you know that something works!
imo, Paysftw!
mariosraptor said:
format sd card and reinsert. be sure to backup important data.
btw wipe-flash-rewipe. post results
Click to expand...
Click to collapse
FUNTASTIC! thanks a lot!!
the test with sense based roms will have to wait till "next time" - formatting the SD card fixed my problem.
my windows PC could only handle the FAT32 partition - but I could still erase the rest and that's good enough for now
thanks again!
glad the community helps. personally i would suggest-if you want a nonsense rom- that you should go for the stable version of opendesire. it is 4.0.15.
regards
Marios
dampf said:
FUNTASTIC! thanks a lot!!
the test with sense based roms will have to wait till "next time" - formatting the SD card fixed my problem.
my windows PC could only handle the FAT32 partition - but I could still erase the rest and that's good enough for now
thanks again!
Click to expand...
Click to collapse

Battery and Lag Isuues Starburst

I made a thread on this before and didnt get much help so this im doing it right.
Size of sdcard used: 8gb Kingston class 4
Size of each partition created and type of partitions made : Primary fat 32 (4.7gb) and Primary EXT4 (2gb)
Software used for partitioning (Gparted, Amon Ra recovery etc): Gparted
Recovery Software installed, with version and subversion number (Eg: Clockworkmod 3.0.0 R3): Clockwork Mod Recovery 2.5.0.7
Whether you are S-OFF or S-ON (If you dont know what this is, or you dont have the picture of a Joker holding a card, on the bootup screen, you are S-ON): S-OFF
Detailed account of steps you did for the procedure, with output/errors at each step as received from the Recovery/Partitioning software: This part im not too clear about
Did you do a full wipe from Recovery before installation?: Yes
If you didnt, what ROM were you running previously?:
Version of the ROM you installed, and the names of the Data2SD installer/reinstaller flashable zips you used (if any.): Starburst (1.3.3.5) – Standard Edition Data2Sd installer (Stable) VersionCode :1.3tiny
If you’re using a custom kernel, full name of the kernel with author name, the kernel voltage if known, whether you have an overclocked/undervolted configuration: None
Did you get any of the following messages in recovery? …………………………………….
sd-ext could not be formatted, file already exists?
Failure mounting ‘sd-ext’
Or a message similiar to the above?: No
My battery is draining in 9 hours of moderate use opposed to full days or more before rooting and using this custom rom. It also lags now, it will be all zippy then it will freeze for a few seconds or just lag insanely. Maybe the battery issues are stemming from the cpu working too hard trying to deal with the lag. Thats just me brainstorming but ya, if anyone could help me out here I would greatly appreciate it.
(As of now I am using a default homescreen free of all custom apps to see if the problem is stemming from one of them) EDIT: it made no difference so I am assuming it is not a running app.
(Also, it lagged as soon as starburst was installed so maybe the apps have nothing to do with it. Another issue is that when I press the power button to turn the screen on the screen dosent always turn on. This is another issue associated with the lag that is bothering me)
A note. The battery melts away when I start to use apps, the internet or anything that takes the phone out of standby mode. If I'm correct the kernel in the starburst rom overclocks the CPU to one thousand and something. Maybe this could be my problem. And if you think this may be the case could you recommend a better kernel to me? Thanks
Sent from my HTC Desire using XDA App
I think I may have figured out the issue. You see, when I first installed the rom I restored my default settings effectively replacing my new fancy rom with the old one.
When I wiped the internal memory (2 gb or so off of ext 4 primary I think) the external still had a few files on it from the last install of the rom. I left those there thinking they would be no issue. Could those remnants from my first starburst install be the cause of my issues?
Sent from my HTC Desire using XDA App
Joshua3109 said:
I think I may have figured out the issue. You see, when I first installed the rom I restored my default settings effectively replacing my new fancy rom with the old one.
When I wiped the internal memory (2 gb or so off of ext 4 primary I think) the external still had a few files on it from the last install of the rom. I left those there thinking they would be no issue. Could those remnants from my first starburst install be the cause of my issues?
Sent from my HTC Desire using XDA App
Click to expand...
Click to collapse
Wipe and repartition with Gparted, this time only leave 1 Gb for ext4. Dont install Setcpu and dont manually set vdd levels for kernel. See if it lags before any apps are installed. If it doesnt try restoring apps with Titanium and see again. Since you do have 10 posts, why dont you continue this qn in StarBurst thread? Please dont PM me. I rarely if ever check these!
Btw..you can also flash the Leedroid 2.2f from Kernels section of my site. It's known for its better battery life.
Should we erase all previous files when updating roms? Do they cause trouble?
hurin8 said:
Should we erase all previous files when updating roms? Do they cause trouble?
Click to expand...
Click to collapse
If your previous installation worked fine, no need to wipe. If you are coming from another Rom, you definitely need to wipe

hTC Desire keeps freezing after on rooted ROMs

Hey guys.
A while ago I`ve rooted my hTC Desire and did an S-OFF, to be able to install custom ROMs.
I`ve "tested" a few custom ROMs, but none of them seemed to be stable.
Currently I`m on SuperNova_Classic_2.0.2.0 with built in Data2SD (iData2SD)(the idea is to have a stable rooted ROM, with DATA2SD and Sense), but every time I flash the rom, then install my fav apps, the phone keeps freezing at certain points, sometimes it runs OK for a week - with no freezing - other times it freezes in the first couple of days after ROM flash. I`ve tried not to install that many apps, but I`m still facing this freeze problem.
Has anyone experienced this before?
Here are the steps I took for ROM flashing
1. Created a 1GB ext4 partition on SD-CARD, preceded by a FAT32 partition(as required in the tutorial of Supernova)
2. Rebooted into Recovery - wiped data/factory reset; wiped cache partition; wiped Dalvik Cache
3. Installed the ROM zip file from SD-CARD; on first boot, except for the Wi-Fi connection, I haven`t touched anything(google accounts etc. - skipped all steps - ), waited for the system to stabilyze, then did a normal reboot in order for the DATA2SD function to work. After next reboot, DATA2SD was working properly(I even had the pink LED light up), Storage Information was showing the 1GB ext partition as an internal memory.
4. Installed all my apps, configured phone, widgets etc.
This way, at a certain point, the phone simply freezes, have to remove the battery to be able to use it again.
Here are my phone specs:
Bravo PVT1 SHIP S-OFF
HBOOT-6.93.1002
MICROP-031d
TOUCH PANel-SYNT0101
RADIO-5.17.05.23
ClockworkMod Recovery v5.0.2.0
Transcend class 4 - 16GB microSD card
I`ve searched and searched on xda-developers, but haven`t found an answer for my problem, yet.
What am I doing wrong here?
Any help would be DEEPLY appreciated !!!
This is no help to you.... but I'm having exactly the same issue.
Sometimes it freezes when starting a game, but most of the time it won't unlock(ie phone unresponsive when I try to wake it).
This is not ROM related as it happened on several different Roms, with a full wipe between. I'm not overclocking.
The only things I can think of are:
-Partially corrupt ext partition on SD.
-failing hardware.
-some other sw issue ie radio(which has worked for a while before this started happening).
Thanks for your reply, Shaun - it does help, at least now I`m not alone in this
You`re right, it`t not ROM related, I`ve tried different ROMs myself, same problem.
I`ve also tried another SD CARD (class 2).
I don`t think it`s the radio, I have the latest version, the version required on Supernova tutorial for best compliance.
I really don`t want to believe that it`s a hardware fault, as I didn`t overclock either and always read/followed the exact right/official steps in root-ing/flashing ROMs.
I`ve reinstalled Supernova now, with absolutely no additional installation of fav apps. Going on 2 days with no freezeing, so far.
I`ll keep post-ing if any new developments occur.
Cheers.
You've not installed any apps at all? hmmm.
When you do re-install your apps(I assume from Titanium backup?), it'd be interesting to see if it starts freezing again.
This would then suggest either a dodgy app that we both have, or titanium backup itself causing the issue.
What SD card specs?
Sent from my HTC Desire using xda premium
rootSU said:
What SD card specs?
Click to expand...
Click to collapse
I'm using the same card that i've had for the last 18 months-
it's an 8gb class 2 card with 768mb partition, the rest is Fat32.
I`ve started reinstalling some of the apps, the most important ones, like iGo, YahooMessenger, YahooMail, etc., but didn`t use Titanium Backup, installed them manually using Market.
So far, so good, no freezing.
My SD CARD specs: Transcend Class 4 - 16GB; 1GB ext2 partition for apps, and the rest is FAT32.
LE
I could be wrong, but from what I`ve seen so far, I would recommend NOT to use widgets that require superuser permissions. Also, before flashing any pre-rooted ROM, be sure to turn "Signature verification" OFF, in the phone`s "Recovery" screen options. If your ROM has any kind of "Data2SD" scripts integrated, after flashing ROM - at first boot, DO NOT configure anything (google account, sync, etc.), DO NOT download/install any apps yet, ONLY enter the Wi-Fi settings(if that is the case); leave the system to stabylize, then do a normal reboot(if the ROM supports "Fast boot" - turn it OFF before rebooting). At second normal boot, the DATA2SD scripts should kick in ( u should see the phone`s notification LED turn to: pink or blue - depending on the script used by the ROM).
A class 2 is a definite no no for Data2sd IMHO. Class 4 is debatable. I had a bit of lag with an older version of data2sd on a class 4. It may be better now, Depends what speed the card writes at really. If its minimum for class (4 MB/s) that could be a bit touch and go. EXT 4 would be the best option for the 2nd partition
I recommend using an a2sd+ solution temporarily to see if the freezes go away
I would mind the lag, I didn`t get any lag using my card though, but just saying, would mind if it would be laggy, the real problem is the constant freezing I`ve had.
If it`ll freeze again, I think I`ll go back to stock Froyo, use Apps2SD and install only the bare minimum.
U know, another thing I never quite understood, I think hTC makes one of the best smartphones on the market, but they limit their possibilites with small batteries and very little internal storage space. What`s up with that?
rootSU said:
A class 2 is a definite no no for Data2sd IMHO.
I recommend using an a2sd+ solution temporarily to see if the freezes go away
Click to expand...
Click to collapse
I'm not using Data2SD. I'm using A2sd+. Same partition that I used on my Hero, and now my Desire for the last 14 months. Still getting freezes.
I don't think it's a speed issue.
a2sd should be fine on a class 2. What a2sd solution is it? Did you move dalvik too?
Its just a logical approach thats needed.
1) Eliminate the SD card by not running from it.
2) Change the rom
3) RUU
If after all that it still freezes, sounds like HW....
rootSU said:
a2sd should be fine on a class 2. What a2sd solution is it? Did you move dalvik too?
Its just a logical approach thats needed.
1) Eliminate the SD card by not running from it.
2) Change the rom
3) RUU
If after all that it still freezes, sounds like HW....
Click to expand...
Click to collapse
Yeah that's pretty much what I was thinking.
I'm currently on InsertCoin with A2SD+. I was on LeeDroid, then RunnyMede before that with the same issue. I did a full wipe when swapping Roms. Not sure about Dalvik- if it's done in the Rom then yes, otherwise I haven't consciously moved it.
1) I might try a different SD that i have lying around- Nandroid it etc.
2) As above, already done that.
3) Last resort. Although a rooted RUU wouldn't be a massive issue for a day or 2.
If it's HW, I better get some insurance.
Edited to add: my SD card is actually a class 4. SD card tests suggests read speeds of 19-20mb/s and write speeds of 7-9mb/s.
Fixed my issue. It's the Kernel. Apparently the latest 2 kernels have the ability to undervoltage when not in use. Unfortunately, this can also cause the lockups i've(and possibly you've) been experiencing.
The last kernel without this in is: 2.6.35.14_110911.
This has 100% solved my issue and I recommended flashing it if you still having the same issue.
Great.
If I get another freeze, I`ll flash the 2.6.35.14_110911 kernel u`ve recommended.
Thanks a lot, dude.
If ever in Romania, look me up, got a few beers with your name on them
LE
If it`s not too much to ask, could you possibly post a download link for that kernel version?
i_cs_u said:
Great.
If I get another freeze, I`ll flash the 2.6.35.14_110911 kernel u`ve recommended.
Thanks a lot, dude.
If ever in Romania, look me up, got a few beers with your name on them
LE
If it`s not too much to ask, could you possibly post a download link for that kernel version?
Click to expand...
Click to collapse
No problem.
I've never been to Romania...
Kernel at the bottom of this post:
http://forum.xda-developers.com/showpost.php?p=18894823&postcount=10450
Did you flash the kernel while on existing ROM, or did you reflash de ROM as well?
And what ROM are u using with this kernel?
try using the earlier versions of super nova and data2sd, I also had the freezing problem but that was AFTER I upgraded to the newest version of supernova and data2sd
I`m using the 2.0.2.0 version, not the latest 2.4.0.0.
Earlier than 2.0.2.0?
i_cs_u said:
Did you flash the kernel while on existing ROM, or did you reflash de ROM as well?
And what ROM are u using with this kernel?
Click to expand...
Click to collapse
Flashed straight over the top. Insertcoin ROM.
Use the latest Supernova and see. It has a pretty good kernel.

[Q] Why does my desire freeze running custom ROMs?

Hey guys!
This might be some kind of a noob question but I honestly don't know what I am doing wrong.
I tried different custom ROMs on my Desire and they all share one major fault: my device freezes at least once or twice a day. I tried MildWild Oxygen, MildWild CM, and CM7.1.
First I thought it might be the ADW Launcher in CM7.1 because that was the first ROM I tried, but the others have different launchers and the problem prevails. Also I tried to lower the max CPU frequency but that didn't solve the problem.
Maybe it has sth to do with my partitions? Because I only partitioned my SD card but did nothing more like adding scripts or SD alignment.
Any help will be gratly appreciated.
You can try the file I'm posting below after partitioning your sd card. It'll align and convert your ext3 partition to ext4. This might help. Good luck.
PS: I couldn't post the file because of my low message count. You can search and find the file on google easily. The filename is "alignment_cool_2.zip"
The rom and its kernel could be the prob to .. try runny AIO 5.0.3 no freeze at all
Verstuurd van mijn HTC Desire met Tapatalk
From my experience Runnymade roms were the most unstable roms that I've ever used. Since installing Mildwild's oxygen rom I'm trouble free for quite some time...
anarchyxtc said:
From my experience Runnymade roms were the most unstable roms that I've ever used. Since installing Mildwild's oxygen rom I'm trouble free for quite some time...
Click to expand...
Click to collapse
Runnymede for me was always stable, but I hate the lag. I multitask a lot!
First of all, thanks to you all for participating in this discussion.
I haven't had a single freeze all day and haven't changed a thing.
Is it possible that my problems disappeared all by themselves?
To be honest, MildWild 2.9 was the smoothest of the three from the beginning.
I'll keep you updated.
PS: Suggestions are of course still welcome
another thing just came to me:
could it be that I messed it up with the partitions I made? Because when I did it I felt like experimenting and made a 2GB ext4 instead of 1GB like I had always done in the past.
ok, I was in a bit of euphoria after I hadn't had a single freeze during the day.
Last night I had an unwanted reboot, this morning I couldn't wake my phone when the alarm went off so I had to take out the battery and on my way to work my phone crashed while I was listening to music and I had to reboot twice to get it running properly again...
Try using alignment_cool_2.zip after partitioning. I also don't use swap partition and set that to "0". Since mildwild released a new version of his rom you can repartition and then use alignment tool and install that new version.
anarchyxtc said:
You can try the file I'm posting below after partitioning your sd card. It'll align and convert your ext3 partition to ext4. This might help. Good luck.
PS: I couldn't post the file because of my low message count. You can search and find the file on google easily. The filename is "alignment_cool_2.zip"
Click to expand...
Click to collapse
I'm just wondering why you recommend using this rather than just using gparted to convert to ext4?
I also think people should be careful using it as I believe it will wipe your ext3 contents and therefore could mess up your phone. It may be possible to use recovery to backup the ext3/4 and the recover it but that is beyond my level of knowledge to be honest.
Bradden1 said:
I'm just wondering why you recommend using this rather than just using gparted to convert to ext4?
I also think people should be careful using it as I believe it will wipe your ext3 contents and therefore could mess up your phone. It may be possible to use recovery to backup the ext3/4 and the recover it but that is beyond my level of knowledge to be honest.
Click to expand...
Click to collapse
Gparted doesn't always work too well for me. Also, after formatting and partitioning your sdcard, everything will be wiped out anyway. This file is very easy to use, plus it aligns your partition. You don't have to boot your computer with gparted. If you don't want to lose your stuff on your sdcard, simply copy everything to your computer and move them back after partitioning...
ElZeck said:
another thing just came to me:
could it be that I messed it up with the partitions I made? Because when I did it I felt like experimenting and made a 2GB ext4 instead of 1GB like I had always done in the past.
Click to expand...
Click to collapse
That may well be the issue. I tried to create a 2Gb sd-ext partition (using CWM) and it crashed my phone as soon as it put all the apps into it. . I have seen it reported that it is known bug that it can't handle large ext3 partitions on the SD card, so I reduced it to 512Mb and all is fine.

[Q] CM10 A7 ongoing boot issue

I have an ongoing issue with Galaxy W phone and CM.
The problem is that the phone spontaneously decides to not boot.
I had run CM10 from first Alpha, and on a couple of occasions it would, after several days or weeks use, stay on the CM spinning logo, and refuse to go to interface.
I got around this by keeping a couple of Nandroids handy and just restored them when the boot issue occurred.
On subsequent fresh install, I ran for a couple of weeks with virtually no app installations, to see if something I was running was causing the issue. Turns out no relationship.
I have just flashed Alpha 7 of CM 10 and now its doing it again. This is a fresh install.
I re-downloaded the ROM from the second mirror, and tried flashing with that, but get the same result.
Is it possible the flash memory in my phone is faulty? On a PC if you install an OS - fresh install - and it wont boot, generally its either RAM or HDD. Given this is a recurring issue, I wonder if its the phone, rather than the OS thats causing the problem - as I have tried with several of the Alphas and both download locations of the most recent Alpha and its still happening.
Can anyone suggest?
Is there a chkdsk option for phone flash memory?
thanks
Jim
[edit] just installed CM9 (last beta) and its doing the same thing - stuck at boot animation and will not get to desktop.
Anyone? Any ideas how to fix this?
Sv: [Q] CM10 A7 ongoing boot issue
Flash stock rom and see if the problem still exists. If not, flash cm again. If it does, get a new phone.
Sent through time and space from my s3mini.
16kzx81 said:
I have an ongoing issue with Galaxy W phone and CM.
The problem is that the phone spontaneously decides to not boot.
I had run CM10 from first Alpha, and on a couple of occasions it would, after several days or weeks use, stay on the CM spinning logo, and refuse to go to interface.
I got around this by keeping a couple of Nandroids handy and just restored them when the boot issue occurred.
On subsequent fresh install, I ran for a couple of weeks with virtually no app installations, to see if something I was running was causing the issue. Turns out no relationship.
I have just flashed Alpha 7 of CM 10 and now its doing it again. This is a fresh install.
I re-downloaded the ROM from the second mirror, and tried flashing with that, but get the same result.
Is it possible the flash memory in my phone is faulty? On a PC if you install an OS - fresh install - and it wont boot, generally its either RAM or HDD. Given this is a recurring issue, I wonder if its the phone, rather than the OS thats causing the problem - as I have tried with several of the Alphas and both download locations of the most recent Alpha and its still happening.
Can anyone suggest?
Is there a chkdsk option for phone flash memory?
thanks
Jim
[edit] just installed CM9 (last beta) and its doing the same thing - stuck at boot animation and will not get to desktop.
Anyone? Any ideas how to fix this?
Click to expand...
Click to collapse
What do you mean by clean install?
wipe data and cache?
Try to format /system /data /cache and /sdcard (backup your internal storage first)
MiguelPT said:
What do you mean by clean install?
wipe data and cache?
Try to format /system /data /cache and /sdcard (backup your internal storage first)
Click to expand...
Click to collapse
Thanks guys, very much for your replies
By "clean install" I have gone to wipe menu of CWM and wiped everything, then CM with wipes, then Gapps.
Ok so I need to try to flash with stock ROM. I had considered that but could not find an Australian ROM in the I8150 section of the Forum. Can anyone tell me where I can get one from?
- or -
-- maybe its ok to flash with any English ROM - will achieve the same thing? - sorry if this is a dumb question - I just dont want to make the situation any worse
Try Removing all SD Card,SIM and battery. Then reinsert battery after 15 minutes and reflash the CM10/Stock ROM. It will boot up
miki2o said:
Try Removing all SD Card,SIM and battery. Then reinsert battery after 15 minutes and reflash the CM10/Stock ROM. It will boot up
Click to expand...
Click to collapse
Ok. Thanks for the suggestion. I did that and its stuck on the Logo still. No change.
You can get stock ROM for Australian (Vodafone) from here http://www.hotfile.com/dl/187592956/3abb3c5/I8150TDULM1_I8150TVAULG1_VAU.zip.html
arya_ruby said:
You can get stock ROM for Australian (Vodafone) from here http://www.hotfile.com/dl/187592956/3abb3c5/I8150TDULM1_I8150TVAULG1_VAU.zip.html
Click to expand...
Click to collapse
Thanks very much for the link I have downloaded it
So I noticed something else thats kinda weird.
When I go to /sdcard, its not showing the content of the sd card
So if I swap out the card, it still loads the same folder, not the stuff from the sd card I have inserted.
I have a few of these. All read fine in the PC, but the phone does not seem to recognise the files, as they dont change if I reboot with a different card/different content in.
/sdcard
Code:
../
.android_secure/
Android/
LOST.DIR/
RZR/
Video/
cm-10-2013~ancora-alpha7.zip
gapps-jb-~signed.zip
SD card contents when read from PC
Code:
I8150TDULM1_I8150TVAULG1_VAU.zip
Its as though it has a partition called /sdcard, and can't mount the content of the physical card itself. Anyone seen this before? Is there a way to re-partition internal memory?
16kzx81 said:
Thanks guys, very much for your replies
By "clean install" I have gone to wipe menu of CWM and wiped everything, then CM with wipes, then Gapps.
Ok so I need to try to flash with stock ROM. I had considered that but could not find an Australian ROM in the I8150 section of the Forum. Can anyone tell me where I can get one from?
- or -
-- maybe its ok to flash with any English ROM - will achieve the same thing? - sorry if this is a dumb question - I just dont want to make the situation any worse
Click to expand...
Click to collapse
Just do full wipe you'll not wipe cwm!
My suggestion: Go the Pristine™ Way.
(thread in the General forum)
Sent from my GT-I8150 using xda app-developers app
arya_ruby said:
You can get stock ROM for Australian (Vodafone) from here http://www.hotfile.com/dl/187592956/3abb3c5/I8150TDULM1_I8150TVAULG1_VAU.zip.html
Click to expand...
Click to collapse
I tried that zip, but it started to install and the phone shut down/restarted at beginning of install (just after wipes)
Can anyone else confirms this file actually works?
Is there a Tread source I can refer to?
pepoluan said:
My suggestion: Go the Pristine™ Way.
(thread in the General forum)
Sent from my GT-I8150 using xda app-developers app
Click to expand...
Click to collapse
Thanks for the suggestion. I tried but the problem persists.

Categories

Resources