[Q] CM 7 call drops - myTouch 3G Slide Q&A, Help & Troubleshooting

Hello can someone help me, I have just flashed latest nightly CM7 build. My call drops after proximity sensor turns off screen. I tried flashing latest radio but it still drops calls, I get message: "Out of service area"

zoky4 said:
Hello can someone help me, I have just flashed latest nightly CM7 build. My call drops after proximity sensor turns off screen. I tried flashing latest radio but it still drops calls, I get message: "Out of service area"
Click to expand...
Click to collapse
What build are you using?

I flashed build 31 , but it was the same with previous builds too

Try a different nightly, one that you know works
Sent from my T-Mobile myTouch 3G Slide using XDA App

Can someone tell which nightly build works fine? Thx

Some people seem to have sat around on 14.
I did myself for a bit. Probably till around 22 or 23.

SefEXE said:
Some people seem to have sat around on 14.
I did myself for a bit. Probably till around 22 or 23.
Click to expand...
Click to collapse
Thank you , I will try it and post result

I tried build 14 but it same thing happens, anyone know why? When screen turns off , phone goes in airplane mode. How can I solve that?

Well let's try to narrow it down.
Do a nandroid, wipe and then flash a different rom, CM 6, CR, or even NB's new rom and just see if the same thing happens.
Or you can try flashing a fresh nightly after wiping.

I flashed CM 6 and it works perfect , but with CM7 it doesen't

Are you using Miguel's kernel? I've noticed with recent builds of cm-7 that my phone wont idle down to min setting like it should. Could cause other problems in different phones.
Sent from my T-Mobile myTouch 3G Slide using XDA App

I don't use Miguels kernel , phone just go to airplane mode when screen turns off in conversation

No one can help me with my problem?
Sent from my T-Mobile myTouch 3G Slide using XDA App

aaldiar said:
Are you using Miguel's kernel? I've noticed with recent builds of cm-7 that my phone wont idle down to min setting like it should. Could cause other problems in different phones.
Sent from my T-Mobile myTouch 3G Slide using XDA App
Click to expand...
Click to collapse
Don't mean to hijack a thread, but could you elaborate? I may be having the same issue. Not positive, but I'm running miguels kernel and have had significantly decreased battery life lately.
Sent from my T-Mobile myTouch 3G Slide

Ok , i have rooted the phone , i have s-off and latest radio. I flashed cm7 rc rom , and problem continues , everytime when screen turns off , phone goes automaticaly in airplane mode. Someone please help me if you know what I could do. Thank you

zoky4 said:
Ok , i have rooted the phone , i have s-off and latest radio. I flashed cm7 rc rom , and problem continues , everytime when screen turns off , phone goes automaticaly in airplane mode. Someone please help me if you know what I could do. Thank you
Click to expand...
Click to collapse
Wipe and flash RC1. Back up your user apps with titanium backup, do a factory reset wipe, and flash cm7 rc1, then boot up, restore your user apps, then go through and set all your settings again. Wiping should solve it.

MusicMan374 said:
Wipe and flash RC1. Back up your user apps with titanium backup, do a factory reset wipe, and flash cm7 rc1, then boot up, restore your user apps, then go through and set all your settings again. Wiping should solve it.
Click to expand...
Click to collapse
I tried as you wrote , but it does not work, every time screen goes off , phone goes in airplane mode

zoky4 said:
I tried as you wrote , but it does not work, every time screen goes off , phone goes in airplane mode
Click to expand...
Click to collapse
Do you have the latest radio installed? If you go into settings>about phone, what is your baseband version? Should have 7.15 in there somewhere. If it says 7.09 or something else, you need to update to the latest radio, search froyo radio update in the dev section. It was posted by chiefz_reloaded.
Sent from my T-Mobile myTouch 3G Slide

i have baseband version: 47.63.35.21U_7.15.35.16 and kernel version: 2.6.29.6-cyanogenmod

Q
zoky4 said:
i have baseband version: 47.63.35.21U_7.15.35.16 and kernel version: 2.6.29.6-cyanogenmod
Click to expand...
Click to collapse
Someone correct me if I'm wrong, but doesn't cm7 have a .32 kernel? .29 doesn't work anymore with wifi calling and such. If you have miguels smartass kernel, try flashing that, that's a .32 kernel. But I'm pretty sure cyanogenmod's kernel is .32 now...
Have you flashed a different kernel over cm7? Or did you just flash cm7 w/ gapps?
Sent from my T-Mobile myTouch 3G Slide

Related

[Q] Flashed Myn's Warm 2.2 (RLS 5), 4G radio not working

I flashed the ROM a few nights ago and followed the instructions regarding flashing the new Radio pack but after noticing that 4G just wouldn't turn on I tried going back into recovery and flashing the .zip again. Still didn't work.
Eventually I restored the previous backup because of an unrelated data-loss incident. I restored the backup I made of Warm and tried re-flashing the radio .zip but it still wont work, anyone care to point out what I'm doing wrong?
I've tried searching the ROM's thread but "4g" must not be long enough to search for, and "radio" yielded no help either. I would've posted this there but evidently I need 10 posts before I can post to the Dev forum(A new rule?).
Thanks for reading!
What's your phone information(build,kernel,hboot)?
I thought that stuff was controlled by the ROM developer. It's on HTC kernel 15, build is warm 2.2 RLS 5.
Sent from my PC36100 using XDA App
As it turns out, last night I was able to turn 4g on, but I'm no longer able to do it now. Anyone know what's up?
Sent from my PC36100 using XDA App
I had the exact same problem as you. This just happened out of nowhere which is even more weird. The rom was working fine and then all of a sudden it just stopped allowing me to turn on 4g. I get the scanning then disconnect really quick. Or I get turning on and turning off over and over again. It shows really quick.
What I did was I flashed back to stock with an old nandroid. I went to a area without 4g and tried to let it connect. Of course it couldn't. I then updated my profile 4 times. I flashed back to another rom and it is working again. Still a little buggy but way better than not being able to connect at all.
Jjday7 said:
What I did was I flashed back to stock with an old nandroid. I went to a area without 4g and tried to let it connect. Of course it couldn't. I then updated my profile 4 times. I flashed back to another rom and it is working again. Still a little buggy but way better than not being able to connect at all.
Click to expand...
Click to collapse
Did you go back to Warm? And what profiles are you talking about exactly, and what does that do? I like this fRom a lot so I'd hate to have to switch.
Sent from my PC36100 using XDA App
motherboyxxx said:
Did you go back to Warm? And what profiles are you talking about exactly, and what does that do? I like this fRom a lot so I'd hate to have to switch.
Sent from my PC36100 using XDA App
Click to expand...
Click to collapse
I have been bouncing back and forth between his and mikfroyo. You go into settings and go to system updates and update profile. When it's done hit ok. Do that a few times and restart the phone. See if that works. It took me days to get mine working again. I think it was from flashing from rom to rom all the time and updating and upgrading the radio's that caused the problem. I don't think it's his rom that is causing it in my case at least. Good luck
My standard process when flashing roms and kernels has always been and will be when im done with the flashing . Setup widgets and where I want them , apps , general settings etc etc etc . Then perform Update Profile followed by Update PRL . When those processes are done I usually let the phone settle down some then do a reboot . Again let the phone settle down from the reboot . Then check your 4G connection it should work . My only advice is to stick with roms running off the newest radios . That way you cut out flashing radios causing possible issues with 4G .
So i am having issues with this ROM and was wondering if anyone is having the same issue. Well i see that my awake and run time are the same and spare parts is showing 100% usage on the CPU.
ive tried using all the different kernels to no success.
any help would be appreciated.
Myn's warm 2.2 RLS 5
updated radios
kings 11
I've installed Myn and my 4G doesn't work. It switches between on and off really fast and then sometimes it'll go further and scan, connect, disconnect, and repeat.
Specs: myn's warm TwoPointTwo (RLS5)
Baseband: 2.15.00.11.19
Kernel: 2.6.32.25-netrarchy-toastmod-4.2.1-cfs-bfq-havs-more-smartass
PRI version: 1.90_003
PRL version 60674
NOTE!! I've already checked if my RSA keys have been lost and they haven't.
Any tips would be grateful, I'm going to flash Fresh tonight and hopefully it works.
Jj, and SouthernEvo, thanks for the tips! I cracked the glass on my phone and just got a replacement, when I flashed the radios I didn't get the images the dev said I would: "While the radios are flashing you'll see a little green arrow phone icon for a bit afterwords, Wait on this. You will then automatically be taken back to recovery."
If this time around it doesn't work again I guess I'll try flashing a re-downloaded Radio package!
running_onCode, seems that we might be having the same issues, did you notice anything strange while flashing the radio package? Like I said on this second Evo, when I flashed it I paid attention and didn't get any green exclamation points.
I have this problem as well. I've used the app that checks for the RSA keys and it says I'm good. I've also checked via a console app.
What happens is exactly like everyone else here. Once the WiMax radio is turned on it'll scan for 3-5 seconds, then it says connecting to Sprint for about .5 seconds, then it says disconnect, and repeats. I've flashed and reflashed with the latest radio pack at the top here: http://forum.xda-developers.com/showthread.php?t=715485 . I did that so I could run Myn's Wyrm RLS5. H boot has not been flahed ( think I have a really old version). I've tried different ROMs and there is no difference. I tried going back to my previous ROM and it still didn't work. I tried updating Profile and PRL 5x and doing a shutdown>reboot and there was no change. Any help would be great.
I tried
Standby time: 10
Scan Rate: 30
NAI: [YourMAC]@sprintpcs.com
User Name: your sprintpcs.com account
Realm: sprintpcs.com
Center Frequency: 2647000, 2657000, 2667000
Bandwidth: 10, 10, 10
NAPDIS: 000002
NSPDIS: 000004
Wimax_Scan_Attempt_Timeouts: 1
Wimax_Scan_Retrys: 15
Wimax_Idle_Sleeps: 10
Wimax_Entry_RX(RSSI): -98
Wimax_Entry_CINR: 4
Wimax_Entry_Delays: 0
Wimax_Exit_CINR: 1
Wimax_Exit_Delays: 15
Handoff Threshold: 0
Idle Mode Timer: 0
TLS: Enable
TTLS: Disable
and theres no change
motherboyxxx said:
Jj, and SouthernEvo, thanks for the tips! I cracked the glass on my phone and just got a replacement, when I flashed the radios I didn't get the images the dev said I would: "While the radios are flashing you'll see a little green arrow phone icon for a bit afterwords, Wait on this. You will then automatically be taken back to recovery."
If this time around it doesn't work again I guess I'll try flashing a re-downloaded Radio package!
running_onCode, seems that we might be having the same issues, did you notice anything strange while flashing the radio package? Like I said on this second Evo, when I flashed it I paid attention and didn't get any green exclamation points.
Click to expand...
Click to collapse
Yeah, it seems like we do have the same issue. I'll flash Myn's rom when there is a fix for the 4G or maybe it's just our phones? I got tired of waiting so I flashed MikFroyo and everything is working. I was using 4G a couple minutes after leaving my house yesterday.
Yeah I'm thinking of just flashing another ROM, can't get much help without posting to the ROM thread itself and I guess I can't do that anymore!
It's too bad though, the first time around I had amazing battery life, but this time it's a lot worse
Are you using Titanium Backup? I had the same problem when I used TB, I would wipe everything, flash Myn's rom and them restore all my apps using TB and 4g would not turn on at all, RSA keys were intact but no 4g. I actually did a Nand backup before running TB and after using TB and trying to restore Nand 4g still would not work!
It actually took a while before I figured out it was TB borking the 4g (3-4 installs and reboots). I had to write down all my backed up apps and download them one by one
Hope this helps!
Jfree3000 said:
Are you using Titanium Backup? I had the same problem when I used TB, I would wipe everything, flash Myn's rom and them restore all my apps using TB and 4g would not turn on at all, RSA keys were intact but no 4g. I actually did a Nand backup before running TB and after using TB and trying to restore Nand 4g still would not work!
It actually took a while before I figured out it was TB borking the 4g (3-4 installs and reboots). I had to write down all my backed up apps and download them one by one
Hope this helps!
Click to expand...
Click to collapse
Can anyone confirm this? I'd love to go back to Myn's Rom.
Sent from my Supersonic MikFroyo using Tapatalk.
Jfree3000 said:
Are you using Titanium Backup? I had the same problem when I used TB, I would wipe everything, flash Myn's rom and them restore all my apps using TB and 4g would not turn on at all, RSA keys were intact but no 4g. I actually did a Nand backup before running TB and after using TB and trying to restore Nand 4g still would not work!
It actually took a while before I figured out it was TB borking the 4g (3-4 installs and reboots). I had to write down all my backed up apps and download them one by one
Hope this helps!
Click to expand...
Click to collapse
As a matter of fact I am using Titanium! So I should flash the rom and install the apps one by one or what? That's not really something I'm looking forward to
motherboyxxx said:
As a matter of fact I am using Titanium! So I should flash the rom and install the apps one by one or what? That's not really something I'm looking forward to
Click to expand...
Click to collapse
I doubt it is titanium, I had the same problems with RLS 5 not getting 4g. Have used titanium on Calks, Mik, and Azrael without having 4g scanning / disconnecting issues. There was a fix for this a couple weeks ago, somewhere. Too much for me so I moved on. Ricsim said that battery life is 97% driven by the kernel, not the Rom.
Bump! Anyone?

MIUI problem

I have a problem with MIUI rom. Some days ago, my phone suddenly had FC, now, my phone run really slow and laggy... If I turn off the screen, my phone won't wake up, only four button in the bottom light up.
I wiped everything in CMW (system,data, and cache, also sd-card) but it doesn't work.
The fresh install had the same issues
I have this problem only with MIUI rom
any help
You probably need to provide more info on the issue. What version of MIUI are you running? Have you tried a fresh download of the ROM?
zandroid said:
You probably need to provide more info on the issue. What version of MIUI are you running? Have you tried a fresh download of the ROM?
Click to expand...
Click to collapse
i have tried from 1.8.5 to 1.9.2.
it's very weird
this guy has the same problem with me, maybe he can explain better than me
http://forums.miui.us/showthread.php?3740-Display-won-t-wake-from-sleep
Hey guys, I flashed 1.819 yesterday and everything was going great. The ROM ran smoothly and I was having no issues at all. When I woke up the next morning my display would not turn back on. Every time I tried to turn on the display the soft lights would light up but the display remained unresponsive. The phone still seemed functional as I could hear e-mail and sms notifications coming through.
When I rebooted my phone it was abnormally slow.. mounting the sd card and syncing seemed like it was taking forever and the launcher was very jittery.. if I let my display time out it would not come back on and I'd be forced to pull the battery and try again.
I performed a full wipe through clockwork recovery (everything, including wiping system,data, and cache in 'mounts and usb') and reinstalled 1.819. The fresh install had the same issues.. if I let my display time out I wouldn't be able to turn it back on. I thought I was having some wonky hardware issue but after flashing my previous sense rom and everything is working perfectly.. so I'm pretty much scratching my head here. My phone was kickass for one day and became allergic to MIUI overnight!
Click to expand...
Click to collapse
Have you tried using a different kernal such as Tiamat or JD's Kernal?
May want to try that. I had good luck with Miui and Tiamat (ran it for a week)
PacerguyDon said:
Have you tried using a different kernal such as Tiamat or JD's Kernal?
May want to try that. I had good luck with Miui and Tiamat (ran it for a week)
Click to expand...
Click to collapse
i have tried both
Does this happen immediately after you flash? Or are you installing applications to get back to your preferred setup and then seeing the performance problems?
If it's the latter, I'd run the rom alone and see if it runs normally. Then install your applications individually until you encounter issues.
ttupa said:
Does this happen immediately after you flash? Or are you installing applications to get back to your preferred setup and then seeing the performance problems?
If it's the latter, I'd run the rom alone and see if it runs normally. Then install your applications individually until you encounter issues.
Click to expand...
Click to collapse
immediately after the flash. I don't install any other apps
since we are talking about MIUI issues. I am running the latest version of MIUI with the JDKernal.
The camera has color distortion lines when I take a picture. The picture comes out fine but when taking it the image shows the distortion. It did not do that before so I can only assume its something with the camera in the ROM.
Anyone else see this?
spiderj said:
since we are talking about MIUI issues. I am running the latest version of MIUI with the JDKernal.
The camera has color distortion lines when I take a picture. The picture comes out fine but when taking it the image shows the distortion. It did not do that before so I can only assume its something with the camera in the ROM.
Anyone else see this?
Click to expand...
Click to collapse
Try different kernel
Sent from my Incredible 2 3D using XDA App
tenchu_712 said:
immediately after the flash. I don't install any other apps
Click to expand...
Click to collapse
tenchu, your signature says you are not English or American. Are you running the MIUI.us ROM on your incredible 2 in English - and not another language?
.....just a thought.

[Q] lost 3g completely

OK here's the deal. I rooted my wife's Inc 2. Put on miui the newest version. Then I put on tiamat 1.1.5 kernel. When u turn on wifi, make a call or restart the phone bye battery pull or power button it will lose 3g. It is impossible to get it back. I have tried everything that I can think of. Airplane mode, wifi on and then off, restarting phone check all options that could affect it. I have tried with the miui kernel and no luck. Also I have the same setup on my phone and I have no issues. If anyone has any ideas on why this is happening I would love to hear them.
You should try updating the kernel, that will most likely solve your problem.
Do u mean just a different kernel?
fbmustang69 said:
Do u mean just a different kernel?
Click to expand...
Click to collapse
Tiamat works great with miui. My first flash borked the wifi too, and a simple reflash of the same kernel fixed it. The kernel included with miui is from cyanogenmod, i believe, and it works fine too.
Do you use a script to wipe the old kernel before installing the new one?
I use the ultimate kernel cleaning script v2 and have had no issues with tiamat.
Thanks for the ideas I will try them out.
Can you give us a feed back I am desperate ,
I downloaded miui from rom manager and miui.us. If I used miui rom from miui.us 3g did not work. If i used the one from rom manager it did work. I know it weird but i was using the one from rom manager on my phone and the 3g was working. Since i didnt put rom manager on her phone i used miui.us. so when I put rom manager on her phone and used that it worked. I dont know why this happened just glad she gets 3g again.
With MUIU right ? i will try it soon , thanks for the idea
It's weird but if i get get back my 3G with it i will use it
If you can run other rom as virtuous an confirm that this method work ,it will be grateful and more hopeful , now too many guys include me are in this situation.
Thanks in advance now five days without 3G, is terrible
up
Any idea here ?
i used rom manager to download miui and the 3g worked. when i used the download from miui.us it 3g did not work. Im also not using miui kernel if that matters. i have used tiamat 1.1.5. i'm Using aeroevan_inc2-0.4 kernel now.

wifi issues with cm10 based roms

whenever I load a cm10 based rom my wifi drops after 2 minutes. stock based wifi is consistent but as soon as I load cm10, jelly ro, or even the new experimental m1 build with always drops. to reconnect I have to turn off and on wifi. is there any solution? I was reading about cm10 modems and I didn't install anything besides cm10, aosp jelly camera and jelly gapps. any help will be greatly appreciated!
ps just realized I install the camera on every build could that mess it up lol
I've been running several nightlies over the last few weeks and now I'm solid with the M1 build and at this point I have never experienced an issue with wifi dropping.
What steps did you take to flash CM10? (cache clearing? Full wipe? Permissions?)
Ian
Ian1331 said:
I've been running several nightlies over the last few weeks and now I'm solid with the M1 build and at this point I have never experienced an issue with wifi dropping.
What steps did you take to flash CM10? (cache clearing? Full wipe? Permissions?)
Ian
Click to expand...
Click to collapse
I did everything except permissions. Are there permissions for wifi?
No I was just mentioning the common steps so you would tell us everything. Sounds like you've installed the rom correctly but obviously their's an issue. I'm assuming that this issue is right after a clean install and not after you've installed juice defender or something like that? Assuming you're installing the correct version of CM10 for your phone (d2att?) their shouldn't be anything else needed to make wifi work (ie modem file).
If I were you I'd be tempted to redownload CM10 m1 and jellybean Google apps. Ensure you have the recommended version of cwm installed. Clear caches, full wipe, flash CM10 and apps followed by clearing of the caches again. Forget the camera initially and test the wifi. If it still doesn't work we'd need to start looking at logs.
Ian
Ian1331 said:
No I was just mentioning the common steps so you would tell us everything. Sounds like you've installed the rom correctly but obviously their's an issue. I'm assuming that this issue is right after a clean install and not after you've installed juice defender or something like that? Assuming you're installing the correct version of CM10 for your phone (d2att?) their shouldn't be anything else needed to make wifi work (ie modem file).
If I were you I'd be tempted to redownload CM10 m1 and jellybean Google apps. Ensure you have the recommended version of cwm installed. Clear caches, full wipe, flash CM10 and apps followed by clearing of the caches again. Forget the camera initially and test the wifi. If it still doesn't work we'd need to start looking at logs.
Ian
Click to expand...
Click to collapse
ya shes still being stubborn. how do i show logs for you?
Hey, I was hoping someone else would chime in about the logs. I have used "alogcat" for logs before but I'm not familiar with wifi filters so I'm probably not the best person to help at this point.
Anyone?
Ian
Running the new cm10 15th build wifi is more stable but still drops after about 10 minutes. Any help would be very kind.
With all your flashing and even using latest versions I'd start to wonder if something to do with the rom is not compatible with you're rougher. Have a you tested it on an alternate wifi source? Maybe a neighbors open signal or something. It's a noob thought but it couldn't hurt.
Sent from my SGS3 I747m on CyanogenMod 10 using xda premium
Yes I have. Currently on a different network right now and it was still dropping. Less frequently but still happening.
I've been trying to get alogcat working on my phone but the log is blank no matter what I do. Either way, the main developer thread just got a post about wifi and how it's note staying connected. No responses yet but it would become a good place to follow as that's where the CM brains are. If I can make some sense offer this log business ill get back to you without some more ideas.
That post: http://forum.xda-developers.com/showthread.php?p=31612608
Sent from my SGS3 i747m (Bell) on CM10 (Yesterday's Nightly) using xda premium
---------- Post added at 09:39 PM ---------- Previous post was at 09:33 PM ----------
There we go, if you go into settings > wifi > menu button > advanced their is several options about wifi timeout, power saving and sleep mode. Their is a frequency setting as well you might want to toy with. I think I stumbled upon these options a while back but never had any use for them.
Sent from my SGS3 i747m (Bell) on CM10 (Yesterday's Nightly) using xda premium
Ian1331 said:
I've been trying to get alogcat working on my phone but the log is blank no matter what I do. Either way, the main developer thread just got a post about wifi and how it's note staying connected. No responses yet but it would become a good place to follow as that's where the CM brains are. If I can make some sense offer this log business ill get back to you without some more ideas.
That post: http://forum.xda-developers.com/showthread.php?p=31612608
Sent from my SGS3 i747m (Bell) on CM10 (Yesterday's Nightly) using xda premium
---------- Post added at 09:39 PM ---------- Previous post was at 09:33 PM ----------
There we go, if you go into settings > wifi > menu button > advanced their is several options about wifi timeout, power saving and sleep mode. Their is a frequency setting as well you might want to toy with. I think I stumbled upon these options a while back but never had any use for them.
Sent from my SGS3 i747m (Bell) on CM10 (Yesterday's Nightly) using xda premium
Click to expand...
Click to collapse
None of those settings ever help me. Can anyone report if CM10 is working perfect on there rogers galaxie s3? Tomorrow is my last day to return my phone so if it's every odd phone I'll just get a replacement.
T-HO6969 said:
None of those settings ever help me. Can anyone report if CM10 is working perfect on there rogers galaxie s3? Tomorrow is my last day to return my phone so if it's every odd phone I'll just get a replacement.
Click to expand...
Click to collapse
Same problem here with wifi on Galaxy Note n7000. It started since I moved from CM9 to CM10.. Now trying every new Nightly, but with no success. Still losing wifi spot every 1min - 10minutes.
Thought if I download something, then wifi is stable, but soon after download is finished, wifi connection is dropped.
Working for me ...
T-HO6969 said:
None of those settings ever help me. Can anyone report if CM10 is working perfect on there rogers galaxie s3? Tomorrow is my last day to return my phone so if it's every odd phone I'll just get a replacement.
Click to expand...
Click to collapse
I have a Rogers S3, and am currently running CM10 NIGHTLY 20120924. Everything appears to be working well, including Wifi; however, there is the occasional (and I mean quite rare) glitch where Wifi does seem to have a bit of difficulty connecting. Again, this is extremely rare on my device, and it may simply be something unrelated to the ROM.
Peter
YES!! This has occurred for me on the stock ATT TW rom and then same thing happened on EVERY OTHER ROM I tried after that including AOKP, LiquidRom, Aristodemos....
It's annoying and I don't know what to do.
The wifi will connect and stay blue for 5 seconds then turn grey for 10 more sec and then wifi will completely disconnect and wont reconnect unless i turn wifi off and then on again. im at a complete LOSS.
anyone have any ideas?
Exchange it. Don't put it off just use titanium backup and switch your phone.
I am having issues with WiFi on CM10 also. I can use the internet like always but the signal bars will go gray sometimes then back to blue. While they are gray I can browse, usually with chrome, but youtube will not work. It is odd that some apps won't work but some will. It may be dropping and coming back but is not strong enough to stream video.
I am using CM10 10/9/12 nightly and an N600 Netgear router. I am starting to think the Netgear router might be my culprit. I have always had dropout issues with them in the past, although, my computers, 360, and PS3 have no issues. Maybe I could just make it a signal repeater and get a Linksys again.
Has anyone else had this issue, think it is the Netgear? Should I try a new router firmware like dd wrt?
Android 4.0.4 error installing cyanogen 10
hi there, I am having trouble installing Cyanogen 10 on my galaxy s3 I747m android 4.0.4
rooted and running cwm 5.5.0.5.
i get an error that says status 7. installation aborted.
Does anyone know why I'm having this error?
thank you
androidehca said:
hi there, I am having trouble installing Cyanogen 10 on my galaxy s3 I747m android 4.0.4
rooted and running cwm 5.5.0.5.
i get an error that says status 7. installation aborted.
Does anyone know why I'm having this error?
thank you
Click to expand...
Click to collapse
Because you are in the wrong thread.
And you need to redownload and wipe everything.
thacounty said:
Because you are in the wrong thread.
And you need to redownload and wipe everything.
Click to expand...
Click to collapse
my bad. I'll try to do that as soon as the website come back up to redownload the file and try it again.
thank you
androidehca said:
my bad. I'll try to do that as soon as the website come back up to redownload the file and try it again.
thank you
Click to expand...
Click to collapse
Meant that kind of silly, but yea you should just redownload, that is usually the problem. Try out Euroskanks version for now if you don't want to wait. Jellybro.

LeeDroid HD V3.3.3 reboots on WiFi/3G/GPS

Hi there,
I'm coming here, because I cannot find the answer to my questions, and you guys can always help
I'm using custom ROM on my Desire, LeeDroid HD V3.3.3 GB R5. Everything is superb, except one little thing. Whenever I switch on WiFi, 3G or GPS it reboots after a while. And it always goes into bootloop, so I have to take the battery out. It only happens when phone is working hard - it's getting hot, that's what i've noticed too. I thought it might be the temperature, so i downclocked the CPU to 900 MHz, but it didn't worked either.
Kernel ver: 2.6.35.10 -g3f43272
If u need any other info, just write it down here.
Any ideas how can i work it out? I don't wanna change ROM, but i need GPS sometimes (that's when it reboots most often...)
newly installed ROM
I've reinstalled ROM. Now it only reboots in gps nav. Any clues? Btw. when revolting, it does not go in to bootloop.
did you try another radio (what about radio recommended by lee)?
Mato_K said:
did you try another radio (what about radio recommended by lee)?
Click to expand...
Click to collapse
That one i use is the latest i guess...
Im having exactly the same problems, though currently my Desire is still running it's original unrooted Froyo OS.
Whenever the phone puts any load on 3G, GPS or the cpu it shuts down and gets stuck in a reboot loop.
MissStabby said:
Im having exactly the same problems, though currently my Desire is still running it's original unrooted Froyo OS.
Whenever the phone puts any load on 3G, GPS or the cpu it shuts down and gets stuck in a reboot loop.
Click to expand...
Click to collapse
If it's not rooted, send it to HTC. (ofc if u still have warranty).

Categories

Resources