Related
what is maximum safe freq. for overcloking artemis ?
in some rom i see 247MHz in default,but Battrey Status can overclock it up to 312MHz!!!
mine is a standard T-Mobile MDA Compact III, and it runs at 201MHz (standard) The 'safe' clocking speed is usually up to 247MHz.
ive got mine scaled (so + and - scaling) and up to 247 with a boost to 273! No problemo's here. 286 goes with no problems too, but uses lots of battery power! I would not recomend to go any higher. The maximum can be different in different makes of the artemis. Ive heard ppl having problems with 286 already.
If you try out to go any higher, be sure to unselect the setting 'scale on reboot'! Then you can give it a SR and try a lower setting again!
I would say 247 as mine crashes above 260 and on 260 the text goes all fuzzy and moves around, like it's tripping.
thanks for your answers
is there any damage to CPU if I overclock it to 312MHz or just it don't work ?
also is there any way to reduce speed for longer battry life
Mine goes to 299MHz without problems, I have it set at a max of 286MHz for a while now without issues. But please see below.
The max frequency beyond which artifacts/faults show up could be different for each individual device - it depends on the production lot of the chip. The max possible frequency also depends on the ambient temperature a lot and generally worsens with ambient temperature - you could go overclocking to 299MHz when you are outdoors in the cold but it may conk out in warmer environments or when summer arrives! That is why I have mine set a notch below the max it can handle. You need to find out the max frequency of your particular device yourself by stepping it up one notch at a time and testing it with various apps for a few minutes continuously. Other's experiences are not useful in this regard. Some people wait a day or two but this is unnecessary as long as you test all scenarios - the thermal time-constant would be of the order of a few seconds.
The above applies to immediate faults which you can observe - there may be some long term repercussions when you overclock it for a period of months or years - the lifetime of the chip may go down slightly due to the higher internal temperature arising from overclocking - but I estimate this may be negligible.
I don't think anybody can brick a device permanently by just overclocking - when the overclocking is removed, it should boot normally. If anybody has experience in *permanently* bricking a device by overclocking, please share it here. BatteryStatus has couple of methods by which it can recover from this condition by removing the overclocking. BatteryStatus also has a neat CPUscaling feature which also saves power when the device is not being used.
-Ravi
I temporary overclock to 273 mhz by Battery Status when playing heavy videos or when I call by Skype, but for normal use my Artemis run very well with standard 201 mhz.
mine 286Mhz without any problem... But my device can't boot up with 299Mhz... keep on restarting...
i have used the search and not found any solid info
what are the benefits of it if any
I haven't heard of people undervolting their fone, although i haven't looked to much.
This would mean though reducing the power that the CPU gets. I would imagine this increases battery life among other things.
Your right about what it is, but almost every custom rom/ kernel is undervolted in development section.
Sent from my HTC Desire using XDA App
Undervolting means, the CPU (or hardware in the phone) gets lower voltages, thus saving more battery & not loosing performance.
Undervolting is a process which reduces the excess "voltage" given to the CPU using a software. This is widely used as a cooling solution and in my opinion more effective than any other cooling solution available (thermal paste, cooling pad, etc) at NO cost. Undervolting will NOT compromise performance at all. Underclocking and Overclocking (clock speeds) is whats responsible in regards to performance. Benchmarks will also prove that performance remains the same.
Click to expand...
Click to collapse
Not excess voltage but fully, manufacturer guaranteed, stable Core voltage to lower guesswork voltages which may or may not work and may or may not cause data loss/corruption.
------------------------------
- Sent via HTC Desire -
A cpu needs power for every 'clock cycle'. 1Ghz means there are a billion per second. IF you lower the voltage, there is less power used. But if you lower it too much, the cpu wo'nt be able to 'cycle its clock'...
So undervolting doesn't affect performance, since the cpu remains on 1Ghz. It decreases the power used, so you get better battery life.
Every single cpu is different, so HTC has chosen a default voltage that (shoud) work on all phones they sell. But your particular cpu could be able to work at a lower voltage. It's just a matter of trail and error. Decrease the voltage until the cpu stops working, then higher it a bit. That way you've undervolted your cpu so it uses the least power.
koenvbeek said:
A cpu needs power for every 'clock cycle'. 1Ghz means there are a billion per second. IF you lower the voltage, there is less power used. But if you lower it too much, the cpu wo'nt be able to 'cycle its clock'...
So undervolting doesn't affect performance, since the cpu remains on 1Ghz. It decreases the power used, so you get better battery life.
Every single cpu is different, so HTC has chosen a default voltage that (shoud) work on all phones they sell. But your particular cpu could be able to work at a lower voltage. It's just a matter of trail and error. Decrease the voltage until the cpu stops working, then higher it a bit. That way you've undervolted your cpu so it uses the least power.
Click to expand...
Click to collapse
Very sensible answer..Thanks
koenvbeek said:
A cpu needs power for every 'clock cycle'. 1Ghz means there are a billion per second. IF you lower the voltage, there is less power used. But if you lower it too much, the cpu wo'nt be able to 'cycle its clock'...
So undervolting doesn't affect performance, since the cpu remains on 1Ghz. It decreases the power used, so you get better battery life.
Every single cpu is different, so HTC has chosen a default voltage that (shoud) work on all phones they sell. But your particular cpu could be able to work at a lower voltage. It's just a matter of trail and error. Decrease the voltage until the cpu stops working, then higher it a bit. That way you've undervolted your cpu so it uses the least power.
Click to expand...
Click to collapse
How would one go about under volting .i have tried everything suggested to me and nothing really seems to make a difference
Sent from my HTC Desire using XDA App
Most kernels are undervolted and unless you can compile the kernel for yourself you are stuck with the values given by the creator. There are two exceptions for this, HAVS kernels which automaticly chose a voltage depending on temperature and some other stuff and SVS kernels with snq-'s volt selection interface (found in Leedroid and maybe some other kernels/roms).
So what exactly have you tried and what did you expect to see? Because the difference won't be that noticeable.
TheGhost1233 said:
Most kernels are undervolted and unless you can compile the kernel for yourself you are stuck with the values given by the creator. There are two exceptions for this, HAVS kernels which automaticly chose a voltage depending on temperature and some other stuff and SVS kernels with snq-'s volt selection interface (found in Leedroid and maybe some other kernels/roms).
So what exactly have you tried and what did you expect to see? Because the difference won't be that noticeable.
Click to expand...
Click to collapse
I have tried battery calibration, using app watch dog to let me know which apps are using excessive CPU. Putting my brightness down to 10%, making sure not everything is synced, the only thing synced is beautiful widgets every 4 hours. And just about everything else that has been put forward to me. Here's another example I just taken my phone off charge at 100% and wrote this and I'm now at 73 %. And its only taken2 mins to write
Sent from my HTC Desire using XDA App
adz63 said:
I have tried battery calibration, using app watch dog to let me know which apps are using excessive CPU. Putting my brightness down to 10%, making sure not everything is synced, the only thing synced is beautiful widgets every 4 hours. And just about everything else that has been put forward to me. Here's another example I just taken my phone off charge at 100% and wrote this and I'm now at 73 %.
Sent from my HTC Desire using XDA App
Click to expand...
Click to collapse
So in short you havent tried any kernel with undervolting at all!
Well that all has nothing to do with undervolting, but (extra) undervolting will not fix the drain problem you have.
Do you use setCPU cause your sig says you run at 1113MHz, which cause higher consumption. Also did you set your wifi sleep policy to never(setting-wireless and network-wifi settings-press menu-advanced-wifi sleep police).
At the moment I have the havs kernel that comes with oxygen 2.0 rc6. I have posted another topic about is the kendal good for battery life etc and no1 has told that another kendal would make anything better
Sent from my HTC Desire using XDA App
TheGhost1233 said:
Well that all has nothing to do with undervolting, but (extra) undervolting will not fix the drain problem you have.
Do you use setCPU cause your sig says you run at 1113MHz, which cause higher consumption. Also did you set your wifi sleep policy to never(setting-wireless and network-wifi settings-press menu-advanced-wifi sleep police).
Click to expand...
Click to collapse
@TheGhost1233, how exactly does one decide which kernel suits us best..
Eg: I see two undervolted kernels (I think) at 875 and 925 mV. I have no idea how to decide. Trial and error?
Froyo Kernel [email protected] min
Froyo Kernel [email protected] min
@droidzone Yes trial and error. The mentioned voltage is the lowest the cpu will get at 245MHz. Not all devices are stable with 875mV (you will know if your phone freezes up) so then you move up to the 925mV min. Other than the voltage there is no difference between 875mV or 925mV.
With the HAVS kernels it can take a while before you notice the freezes cause the voltage is dynamic, so be careful if you need your phone as a alarm clock.
hey guys, just wondering will using a lower vsel damage my cpu and/or battery?
i have previously beein using milestone overclock on 1ghz and 60 vsel and am adding setvsel into the mix, also any ideas on starter settings? thanks
also could someone just give me a heads up on what vsel actually IS
I don't believe there are any studies that show effects of long term use of lowering the voltage, which is what you are doing with vsel in order to save battery juice...or you could increase the voltage but that defeats the purpose and also heats up the battery which leads to shorter life span. Many use it without reporting any damage to battery or cpu, I believe it's safe (however, if you are overheating you might fry the battery or cpu, so you'll need to moniter and play with settings to get the desired effect without any overheating issues).
With regards to setvsel, there are reported issues from users with different roms...from what I've read (and you can do your own research to see if this is what you are seeing...this is the conclusion that I've come to by reading a lot of threads), it is better to use milestone to overclock and setcpu to lower the vsel.
With that being said, I've used them all and like setvsel so keep going back to it...but I've been having some issues lately so I've removed setvsel to see if that is what is causing some problems (too early to tell).
Oh, and as for settings...pop on the overclocking/undervolting thread in the development section to see a lot of different settings and remember that what works for one user might not work for you...you'll have to experiment a bit to find your ideal setting.
oh okay i think i might go back to my old settings with milestone overclock and setcpu and just lower the vsel! i was under the impression for some reason that lowering the vsel would heat the battery. Thanks!
I'm no expert to be honest, I'm more of a research kinda person. From what I've researched, undervolting can help keep temps down, and may particularly help when you overclock (as overclocking is stressing the cpu to go beyond it's normal operating design hence it may heat up...supplying it with less power, or voltage, is what helps keep the temps down.
Of course, this is given you find the optimal setting for your phone, and as it seems from reading through these forums, many users have experienced completely different results using the same settings (i.e., one user will have a stable setting without any problems while another user on the same rom using the same settings will have crashes and/or issues like overheating). Doesn't seem right, but it is what it is
yeah ive read through most of that stuff too, i went down to 1ghz at 51 vsel, seeming stable, but i decided to go with 54 anyway
1.1 GHz @ Stock vsel for over a month without any issues...I hope it lasts.
Sent from my MB525 using XDA App
Hi,
I've also read a lot regarding the underclocking 'dangers' but couldn't find anything to prove that there is such an issue. I think that it is an urban myth spread everywhere by people asking if there is a danger with low vsel [but that are never getting a positive answer on it].
The only thing I found using setvSel is that I had to first install Milestone Overclock and load its module prior to start setvsel. There is a way around it, but requires you to copy files in the system folders and change their permissions. I find that my way is much easier.
As far as over-heating goes, it's an overclocking thing; not underclocking.
My Defy is set at 900Mhz and really, I don't see the point of going much higher: everything runs smooth and lag free already.
vsel: 21/300; 32/600; 43/900 - 90% up_threshold
Been like that for about a month now and never experienced any problem at all.
The underclocking is great for saving battery; no exact numbers to give here but it feels like my battery now last 2 times longer. I can easily get 4 days between charges with low/moderate usage and would get to 6+ days "IF" I could stay away from games and having the screen ON for long sessions of browsing/video watching.
I tried SetCpu before but I didn't like the interface; the simplicity of SetvSel is really nice.
i use setcpu for scaling and profiles, and run 18/300, 36/600, 50/1000 stable and smooth as
Undervolting is not a bad thing at all. It means less Watts consumed for running (Watts = Voltage x Amperage), less of your battery consumed.
Ussually companies test a large batch of components and how they react on different voltages and freqvencies, and then they decide for a voltage that works with all components and that is safe for all cases. Eg. when they have different CPU speeds and thus different options for CPU's this is one way to decide which one work at 3GHz and which one at 2.7 GHz (the other one is demand for components).
Phisically you will not have any problems and you can't damage your phone by undervolting, so no problem here, only possible software problems if you go too low.
Advantages :
+ Lower processor temperature
+ Lower phone temperature
+ Longer battery time
+ Longer components life
Disadvantages
- Stability issues (freeze, artefacts, slowness)
maxi2mc said:
Disadvantages
- Stability issues (freeze, artefacts, slowness)
Click to expand...
Click to collapse
You know, I was recording a video and when playing back noticed that there were squiggly lines that went through the video a couple of times (in a two minute clip). This was the first time I saw this...and have recently lowered vsel by 2 on vsel3...could that be the artifacts that you are mentioning?
I just figured it perhaps I was too bouncy with the phone while recording making it glitch...but now that I see this post I'm thinking maybe I undervolted too much...what do you think?
My settings: 54/1000 44/700 28/300
I know what people mean by same settings don't work for every phone even if it's the exact same model. My Defy won't underclock as much as others. I'm using SetVesel, and I've been able to drop 5 points from each, and that's about it before it reboots itself. I only tested undervolting, but I mainly overclock to get as much speed as I can, and give it enough juice to run super fast. I'm current running [email protected], [email protected], [email protected] Threshold at 75%. The highest the temp ever got was 112F, and that was after playing a game for about an hour. Usually it stays below 90F for normal use. I get around 17-20 hours out of it with screen on time at about 3 hours @ 50% brightness. I've been running these settings about a month, and have not had any issues.
If you put something like 100vsel will the phone accept and then burn? Is there any protection? Does anyone know what's the highest acceptable vsel?
Just for curiosity...
im pretty sure 80 is the highest you should EVER use and that'll significantly increase the chances of your phone burning out. @bobbyphoenix you should be able to lower your vsels a fair bit or your really unlucky! i run a lower vsel for 1ghz than u do for 700mhz smooth and stable
stewi21 said:
im pretty sure 80 is the highest you should EVER use and that'll significantly increase the chances of your phone burning out. @bobbyphoenix you should be able to lower your vsels a fair bit or your really unlucky! i run a lower vsel for 1ghz than u do for 700mhz smooth and stable
Click to expand...
Click to collapse
CM7, rather non-technical person here. I seem to have a very happy phone at setvsel settings of [email protected], [email protected], [email protected], 86%. Been running this for the month or so since I rooted and the phone feels like it was made for this config. I've never seen the temp above ~32c. My 2¢.
I am new to android phones. And i have no experience about overclock.
Will my cpu easily break down due to keep overclocking?..
Honestly, i seldom change my cell phone model, i want my defy can stay a life at least 1.5yr.
i think overclocking can't really damage your phone, voltage can. so i suggest you keep the voltage around [email protected] (default is [email protected], so this should be fine), and if the phone doesn't hang or reboot, you're good to go but you could try lowering vsels, you know, the lower the voltage, the lower the power consumption, the heat and the chance to fry your cpu but i'm not sure!
Yep, 1 GHz is safe, I'm using [email protected] as well, and the CPU is capable to run easily at [email protected] continuously. The leaked Gingerbread ROM from Motorola uses 1GHz as well, so don't worry, you just have to find the safe vsel settings.
thanks for replying, i m currently using 1GHz @ 58 .. Everything is alright
Should I make the voltage as low as possible?
yeah, just to lower the power consumption and temperature, but it isn't necessary.
Can you share your voltage setting please..?
I do the stability test and it gets successful run for 5min then this means the setting is okay?
i don't overclock, just undervolt, here are my settings (with setvsel):
800MHz - 45vsel
600MHz - 30vsel
300MHz - 18vsel
up_threshold: 90%
actually if you wanna make absolutely sure your device is stable, you should run it like for an hour. but if it runs for 5 minutes without error that's quite okay, you shouldn't have problems with those settings
Thanks so much, i m trying to lower my voltage setting.
Besides, i want to ask about the battery temperature, what is the maximum temperature before getting damage to the cell? I usually goes up to 37~39 degree celsius.. is it normal?
mine is usually around 29-32 °C, but i have it undervolted, so idk. but 37-39 seems a bit high, that means the cpu temp is way over 40 degrees, you should check it out!
EDIT: tried stress testing for 20 minutes with [email protected], it went up to 35°C, so you should definitely find out what's wrong with your device!
I actually underclocked to 600MHz, since I couldn't see a big difference even at 1200MHz in normal usage. A Pentium3 at 4Ghz will still not perform as well as a slower clocked new CPU for example, CPU design is more important - what instructions it supports.
Battery life is more imprtant to me and heat is very bad for Li-ion batteries too.
Also I found changing the CPU governor to "interactive" made a difference in GUI responsiveness and I have had less stuttering.
nisamtetreb said:
I actually underclocked to 600MHz, since I couldn't see a big difference even at 1200MHz in normal usage. A Pentium3 at 4Ghz will still not perform as well as a slower clocked new CPU for example, CPU design is more important - what instructions it supports.
Battery life is more imprtant to me and heat is very bad for Li-ion batteries too.
Also I found changing the CPU governor to "interactive" made a difference in GUI responsiveness and I have had less stuttering.
Click to expand...
Click to collapse
so, what's your standby lifetime after underclocked cpu?
I can see the performance improved when i was watching flash video on browser. But honestly, i dont think there are anymore huge difference after overclocking..
But as the battery life still remains quite well, i will still keep overclocking to 1GHz.. Isn't it a good idea?
nisamtetreb said:
I actually underclocked to 600MHz, since I couldn't see a big difference even at 1200MHz in normal usage. A Pentium3 at 4Ghz will still not perform as well as a slower clocked new CPU for example, CPU design is more important - what instructions it supports.
Battery life is more imprtant to me and heat is very bad for Li-ion batteries too.
Also I found changing the CPU governor to "interactive" made a difference in GUI responsiveness and I have had less stuttering.
Click to expand...
Click to collapse
lol... What happend to HD and THD games... Did u try playing them at 600mhz??
Overclocking to 1 GHz with the right voltage values seems to be absolutely no problem for Defy.
BTW, does anyone know whether it's possible to set scaling governor to "Interactive" mode under Froyo? Gingerbread kernel let me set it, but I haven't found the way under Froyo.
Battery life was a little bit better, the display and 3G always draw a lot of power.
Standby time got better, but I don't use very low vsel any more due to errors in YouTube and dropped connection of radio streams.
Before I used 300-600-800 at 20-30-48, this was very stable in stability test, but for example Youtube would start showing "error playing video". After I increased vsel, it went away.
I mostly did it to lower temperature, optimal temperature for li-ion is around 25°C according to Wikipedia I think.
I don't play 3d games, they would benefit the most from overclock I believe.
Angry birds RIO for example would stutter for a second or two after a level loaded, but it would become as smooth as at higher clocks, when I wait for a second.
I hope flash gets better, when hardware acceleration gets enabled in Quarx's CM7.
I was running [email protected] for a month straight. No issues at all. The highest my temp reached was 112F after playing games for about an hour straight. I now just run it at [email protected], and it's plenty fast for me. I did some "testing" with all the options in SetVsel. It's not science sound, but if you use the Gingerbread Icon in the notification bar, and are running at stock (800 speed) you will notice when the CPU maxes out it doesn't even reach full capacity. I found Words with Friends to really use the CPU, and at 800 it pings the meter in the orange (The notification icon shows green, orange, and red for "zones"). If I overclock it at 1000 or above then the meter goes into the red. I don't know the exact number it switches from orange to red, but being at stock 800 is well below what the chip can really do since it doesn't even max out the meter. I hope I didn't confuse anyone. It makes sense to me.
weird...my cpu at any game reach the 800mhz
yet even in normal situations like browsing through the files on the phone it reaches 800mhz
and also despite the values i use in setvsel are not high(which is:
24 @ 300
34 @ 600
48 @ 800
)
the phone still reaches maximum 38C when i play games and if i set the value in the third vsel the games starts to hang!!
seems like i am the only one who have these problems..but why
anyone have any idea
im running stock arabic froyo btw
if someone can confirm to me that i can keep Arabic language if i installed another rom using custom restore in nandroid then i would be using prays or official 2.3 but no one answered me about that
anyway the important thing is anyone knows why my cpu temp is always high?
Well ambient temperature is important too. If it is 30°C where you live and your phone's temperature is at 35°C I'd say you are good. If the outside temperature is 10°C and your phone is dat 40°C I'd say there is something wrong (unless you were playing games or watching a movie).
in my opinion, it is definitely safe that you overclocking to the leaked moto level.
however, the voltage is still a mystery.
there's no constant conclusion about this.
i'm using [email protected], [email protected], [email protected], and it works fine for me
I'm getting really annoyed. No problems clocking up to 1100mhz with stock voltage (58). But changing the voltage settings, even slightly, makes the phone more or less unstable.
Hey guys, I'm just wondering what settings do you have on your setcpu for the best performance and battery life? I'm totally new to this lol
Sanks
kazemagic said:
Hey guys, I'm just wondering what settings do you have on your setcpu for the best performance and battery life? I'm totally new to this lol
Sanks
Click to expand...
Click to collapse
i i think that ondemand is the best for daily using... i'm using cm10 rom and i have some music problem so i'm using interactive and it's ok. if you don't use games or heavy apps, you can underclock it to 1ghz or even less and put on powersave.. but you have to try and find the best for you
My setup is a little complicated. I use the ondemand governor, then for the profiles I make it use powersave and under 760mhz between 1am and 8:30am which seems to really help during the night. Also set it to use 760mhz max when the screen is off.
When charging or above 40% battery I allow it to run full speed, but only when the screen is on, therefore helping charge times. On charge or above 80% I set the governor to performance.
In call I set the clock to max 1000mhz and conservative to try and allow calls on low-battery to work properly without lag but also without killing the battery.
I have a couple of other options set for very low battery ( < 12% ) too, but those are only to extend the battery if it's dying.
I wouldn't say all this is necessary... but I need my phone to keep working at all times as I use it for receiving business calls.
It's just a matter of playing around really... depends what you use the phone for. For the most part tell it to use lower clock speeds when you don't need them so much (when phone is off, during the night, during call etc) but you will really notice the speed difference if it's underclocked while you use it, so I tend to allow it to use full whack when screen is on, unless the battery is low.
I also set up profiles to make things like Bloons TD4 run in performance mode and min of 1000mhz, to keep them smooth . Drains the battery though!
lol setcpu does a really good job at battery saving. When using ondemand, my phone can last more than 2 days (if it's on standby)
Have you guys tried under-vaulting? What does it rlly do?
kazemagic said:
lol setcpu does a really good job at battery saving. When using ondemand, my phone can last more than 2 days (if it's on standby)
Have you guys tried under-vaulting? What does it rlly do?
Click to expand...
Click to collapse
If you mean decreasing the voltage on the CPU, no I haven't. From my experience in desktop PCs however, if the CPU voltage is too low it can lead to hardware issues and instability.
If something needs a certain amount of power, and you give it less, it will either try and draw more amps which increases heat and can fry components, or won't work properly. You could probably "under-volt" the CPU at the same time as reducing the clock speed however, but your performance will suffer. When the processor is set to be ondemand it underclocks itself when not in use anyway
The biggest battery drain is screen and radios, concentrate on using them less. Underclocking the CPU will make the phone last longer when in use, but usability will suffer and turn your super fast smart phone into a sluggish one. I only make mine stay underclocked when the screen is off, during a call, or on low battery. During general use I let it do its thing .
UV(Under volt) is actually not to bad. Don't ever set those values at boot, else when they are too low, it will cause BOOTLOOPS. It just reduces the amount of power allowed for the cpu to use, thus it won't use more than required. You can't really ask a person for his/her uv values, as no 2 chips are created equal.
People stating that they UC(underclock) their device is not quite right. We don't have much control over our cpu's to be honest. If you run tegra stats whilst using you're phone, you'll see what I mean. It will sometimes(happens quite often) just bump up to higher frequencies to which you UC them. Also as soon as the screen is locked and unlocked the max cpu frequency set by the governor will just return(for example: say stock is 1500mhz, and you set it to 1400mhz, it will return to 1500mhz after an unlock). Ondemand is very very good for battery and performance. But remember you have to tweak those values individually in order to optain the best possible performace for the given task you want. Whether it is for battery or performance.
It's actually also a lot better to just tweak those values as to TRY and uc. Uv will stick, UC not!
Here is a small example as to battery saving and performance values for ondemand governor:
sampling rate:---------60 000 ----- 30 000
up threshold:--------------95 ----- 60
sampling down factor:-------2 ----- 8
powersave bios: ------------3 ----- 0
ignore nice load:------------0 ----- 0
io is busy:------------------0 ----- 0