Hello all. I have an Epic 4g and was attempting to load the modem and pit files via odin3 v1.61 and it completed successfully. I then placed the .tar file for the froyo update in the pda slot and while it was loading my daughter pulled out the cable. I now have a picture that looks like a phone then 2 dots then a warning triangle then 2 dots and then a computer. I tried to do a hard key reset and my bootloader is gone. I am still able to put my phone into download mode and odin can see that it is connected, but when i attempt to do anything it will cot go past this point
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> sph-d700-dk28-8g-rel.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
Any suggestions would be appreciated as I now just have a brick. I can try anything. This phone is not rooted. I just wanted the froyo update.
Can even post in right section.. if I were you id stay away from this stuff.
Sent from my SPH-D700 using XDA App
This should not be in development. You should have searched before posting.
Your phone is not bricked if you can get into download mode. Make sure your tar if the correct size using the md5 checksum. Restart your pc and your phone. Odin is picky. it will take a couple times sometimes.
Sent From Da Hood.
^ what he said, plus there are probably no less than 25 other posts with the same or similar titles/problems.
Please post questions in Q&A section. Everyone please remember to click the "Report Post" button on the original post to have immediate action taken by the moderators. Also do not post in the thread itself telling the user that he made a mistake or broke a rule as it doesn't contribute to the thread and is unnecessary.
Why would you odin the modem and pit files and then Odin the whole tar file? The modem is in the tar file. Your phone is not bricked if yo can get into dl mode. Keep trying with different versions of Odin and make sure the rom is a complete download. Odin is very sensitive. Don't use the pit file when flashing the tar file. There are a lot of threads on here like this and you have to keep trying and eventually it will pass. Find the other versions of Odin and try them. Good luck
Whosdaman said:
Please post questions in Q&A section. Everyone please remember to click the "Report Post" button on the original post to have immediate action taken by the moderators. Also do not post in the thread itself telling the user that he made a mistake or broke a rule as it doesn't contribute to the thread and is unnecessary.
Click to expand...
Click to collapse
Finallyyyyyyyyyyyyyy even though most of my threads get closed cuz of flaming -_-
Sent from my SPH-D700 using XDA App
So if we just report the thread will the mod just move it or will you also flame err I mean let the poster know of his mistake? You would think that just by moving it they would get the message but I would not be surprised if they didn't know why it was moved!
Sent from my SPH-D700 using XDA App
please remove this. see my response below.
MattJimerson said:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> sph-d700-dk28-8g-rel.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
Click to expand...
Click to collapse
Rename "sph-d700-dk28-8g-rel.tar.md5" to "sph-d700-dk28-8g-rel.tar", open up ODIN, then select the renamed file. That worked for me.
Related
So i was trying to run Odin, so that I could update my firmware to 2.2 use the ECO3 method. And it got unplugged while doing it, oops
First it had the bricked little icon with phone and computer and lilttle orange triangle. And then it is just a black screen
When i try to power it up, you can tell that it is one, but it is a dim backlit black. i can sometimes connect it to odin.
any other solutions/roms/updates, or anything i can do to fix it, I WANT MY PHONE BACK
PLEASE HELP!!!!
string14 said:
So i was trying to run Odin, so that I could update my firmware to 2.2 use the ECO3 method. And it got unplugged while doing it, oops
First it had the bricked little icon with phone and computer and lilttle orange triangle. And then it is just a black screen
When i try to power it up, you can tell that it is one, but it is a dim backlit black. i can sometimes connect it to odin.
any other solutions/roms/updates, or anything i can do to fix it, I WANT MY PHONE BACK
PLEASE HELP!!!!
Click to expand...
Click to collapse
Do you have cwm? If do, flash any of the ec07 roms and imnuts hacked kernel. If that doesn't work (it should, unless you tried to repartition) then hit irc, and I'll see if I can help. All of the roms and the kernel are in Ciscogee's database sticky.
PERCEPTION IS REALITY
Thanks for the fast reply, and no, I do not have clock work, how do i get it through download mode only, because odin doesnt seem to flash things on my device well,
any other solutions?
http://androidforums.com/continuum-...rap-i-screwed-my-phone-up-recovery-guide.html
thanks again, i was able to run the odin thin again, but it stops and says
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I400-EC07-FROYO-REL-PRODUCTION.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
help again
Can you read through the forum before creating a thread please?
Sent from my SCH-I400 using XDA App
string14 said:
thanks again, i was able to run the odin thin again, but it stops and says
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I400-EC07-FROYO-REL-PRODUCTION.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
help again
Click to expand...
Click to collapse
Make sure repartition is checked, and you are using the pit file.
PERCEPTION IS REALITY
I did, I have done al that you have told me
string14 said:
I did, I have done al that you have told me
Click to expand...
Click to collapse
Keep trying. That isvthe pain of Odin. It's simple uservinterface, but it doesn't alswaysvwork, the first time. I've had to flash something 4 times before before itvwould pass, and i know I was doing it right. The alternative is HEIMDALL. More complicated, but I've never had a fail when I did it right. I'll be in irc in a few ifvyouveant me to walk you through heimdall.
PERCEPTION IS REALITY
Thank you so much, yeah, could you walk me through it? Please?
I need my phone to work, and the COMport is always messed up, or the write operation fails
Since I don't see you in irc, go here:
http://forum.xda-developers.com/showthread.php?p=18698679
There is a link on there for a tut I made for using heimdall for this situation. And that thread contains everything you need (except 7zip). I'll be in irc in a bit, and be there for most of the day, likely.
PERCEPTION IS REALITY
OK, i found a tutorial on heimdall, but while flashing i get
ERROR: Failed to access device. libusb error: -12
WHAT NOW????
string14 said:
OK, i found a tutorial on heimdall, but while flashing i get
ERROR: Failed to access device. libusb error: -12
WHAT NOW????
Click to expand...
Click to collapse
That is a driver issue. either reinstall the heimdall drivers, or unplug and replug and try again. I'm in IRC now.
Hi,
I am in process of flashing the no data rom for my SPH-D710 and I've been sitting on SetupConnection.. for a while now. Is this normal? I don't want to stop in case it will mess something up.
I have the yellow box in the odin.
Here is my progress so far. Been sitting like this for about 30min.
<ID:0/017> Added!!
<ID:0/017> Removed!!
<ID:0/017> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/017> Odin v.3 engine (ID:17)..
<ID:0/017> File analysis..
<ID:0/017> SetupConnection..
Please let me know if this is normal?
Using: SPH-D710.FE22_CL612283_ROOTED_NODATA-OneClick.exe
Using windows install
Did you ever make it past this step?
Esoteric68 said:
Did you ever make it past this step?
Click to expand...
Click to collapse
No. Still stuck at same spot.
Here is a screenshot
I've been stuck in Odin before (thankfully it wasn't during modem install) and after an interminably long period decided the only option was to disconnect, reboot (I may have had to do a battery pull, can't remember) into Odin mode and try again. Keep in mind this is just something I did and I got lucky. I'm not suggesting you do it but, if you do, I would download another copy of the one-click you are trying to use (FE22) or pick another to see if you can complete the Odin process.
Thanks! Was able to unplug and downloaded another copy from a different mirror. Keeping fingers crossed!
Fingers crossed. Let me know how it goes.
SUCCESS!!
Thank you for your help!
Yay!!! My pleasure.
I want to download the new firmware that was provided by milkyman in the following...
You'll have to flash mikeyman's file (http://d-h.st/57S) via Odin. Just click on PDA, select the file in Odin, and press start. Don't touch anything else. Root/recovery will be unaffected
But Trend Micro flags the server as a source for malicious software and I am not able to get there. Just a heads up to milkyman...
dscycler
My firmware version
dscycler said:
I want to download the new firmware that was provided by milkyman in the following...
You'll have to flash mikeyman's file (http://d-h.st/57S) via Odin. Just click on PDA, select the file in Odin, and press start. Don't touch anything else. Root/recovery will be unaffected
But Trend Micro flags the server as a source for malicious software and I am not able to get there. Just a heads up to milkyman...
dscycler
Click to expand...
Click to collapse
My firmware version is 2.0.1883. No problems today running the 5/16 nightly build...
Does it flag his file, or the website itself?
Just the website
buru898 said:
Does it flag his file, or the website itself?
Click to expand...
Click to collapse
I believe that it is flagging the website as a known source not the file itself. But net result is I can't download the file.
Disabled Trend
dscycler said:
I believe that it is flagging the website as a known source not the file itself. But net result is I can't download the file.
Click to expand...
Click to collapse
Disabled Trend Micro and was able to download the file. Now need to figure out ODIN 1.85,
dscycler said:
Disabled Trend Micro and was able to download the file. Now need to figure out ODIN 1.85,
Click to expand...
Click to collapse
I believing there's Odin 3.07? Think that's the one I used. Just put it under pda and make sure repartition isn't selected.
buru898 said:
I believing there's Odin 3.07? Think that's the one I used. Just put it under pda and make sure repartition isn't selected.
Click to expand...
Click to collapse
How log does the flash take? Messages so far are:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> UVMC6.aio.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
ID:COM is 0:[COM4] and is yellow. The file is in the PDA field. But nothing seems to be happening. twrp v2.4.3.0 running on the phone before connecting to ODIN.
Am I missing something?
dscycler said:
How log does the flash take? Messages so far are:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> UVMC6.aio.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
ID:COM is 0:[COM4] and is yellow. The file is in the PDA field. But nothing seems to be happening. twrp v2.4.3.0 running on the phone before connecting to ODIN.
Am I missing something?
Click to expand...
Click to collapse
It has been sitting like this for 20 minutes. What to do?
dscycler said:
It has been sitting like this for 20 minutes. What to do?
Click to expand...
Click to collapse
Such a noob I am. Finally figured it out and flashed milkyman77's firmware. Now on 2.0.67419. Yeah!!!
dscycler said:
Such a noob I am. Finally figured it out and flashed milkyman77's firmware. Now on 2.0.67419. Yeah!!!
Click to expand...
Click to collapse
You weren't in download mode were you...
buru898 said:
You weren't in download mode were you...
Click to expand...
Click to collapse
Exactly...
Ok, I know someone is going to yell at me. I have searched for 24 hours on this site before deciding to post. Please don't verbally assault me too badly. Here is what happened, overnight, the phone must have gotten an OTA update. It is now frozen at the Samsung Galaxy screen.
I cannot get to CWM which I did have on 4.1.1
I can only get to download / ODIN mode (vol down, home, power.) So I downloaded Odin 3.07 (the newest i think)
I downloaded KIES_HOME_I317UCAMA4_I317ATTAMA4_578342_REV04_user_low_ship.tar.md5 (AFTER A LOT OF SEARCHING!)
I can get Odin to see my phone, com4, I put the above file in PDA and eventually get this....
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I317UCAMA4_I317ATTAMA4_578342_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
Am I doing something wrong? Is it the wrong file I am trying to flash? Is there any way to get CWM back? Because I do have semi recent backups. ANY help would be appreciated. I'm pretty much willing to pay somebody at this point.
Thanks and sorry if I missed the thread on this. I REALLY tried via google and internal XDA searches
- Keith
AT&T Galaxt note 2
Hoping those keywords garner more attention. I am still stuck with a non working phone and my SIM is in an iPhone 4s..... yuck
Also I have a PIT issue?
keithh85 said:
Ok, I know someone is going to yell at me. I have searched for 24 hours on this site before deciding to post. Please don't verbally assault me too badly. Here is what happened, overnight, the phone must have gotten an OTA update. It is now frozen at the Samsung Galaxy screen.
I cannot get to CWM which I did have on 4.1.1
I can only get to download / ODIN mode (vol down, home, power.) So I downloaded Odin 3.07 (the newest i think)
I downloaded KIES_HOME_I317UCAMA4_I317ATTAMA4_578342_REV04_user_low_ship.tar.md5 (AFTER A LOT OF SEARCHING!)
I can get Odin to see my phone, com4, I put the above file in PDA and eventually get this....
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I317UCAMA4_I317ATTAMA4_578342_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
Am I doing something wrong? Is it the wrong file I am trying to flash? Is there any way to get CWM back? Because I do have semi recent backups. ANY help would be appreciated. I'm pretty much willing to pay somebody at this point.
Thanks and sorry if I missed the thread on this. I REALLY tried via google and internal XDA searches
- Keith
Click to expand...
Click to collapse
At least with the MD5 file I am trying to load, It says I need a PIT file. Which I have downloaded, but it just sits there for what seems like forever then gives me this error....
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I317UCAMA4_I317ATTAMA4_578342_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
keithh85 said:
At least with the MD5 file I am trying to load, It says I need a PIT file. Which I have downloaded, but it just sits there for what seems like forever then gives me this error....
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I317UCAMA4_I317ATTAMA4_578342_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Hey, I used to flash my phone like 3-4x a week and the I bricked it, this video helped me get back on my feet, hope it helps. Just go from there as a base and then you flash whatever you need to install on your phone. Good luck!
http://www.youtube.com/watch?v=WwNOAgopXvc
Pit file? I have found 2 PIT files. neither work
Looks like my phone needs to be re-partitioned also? I am completely lost. Reading some of the threads that might mean my internal memory went dead. Anyone?
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
keithh85 said:
Looks like my phone needs to be re-partitioned also? I am completely lost. Reading some of the threads that might mean my internal memory went dead. Anyone?
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
1) Try different USB port.
2) did you put your md5 file in a folder? If so check folder name.
3) Run odin as admin
reply
A_youu said:
1) Try different USB port.
2) did you put your md5 file in a folder? If so check folder name.
3) Run odin as admin
Click to expand...
Click to collapse
Yes to all 3.... I read something about SDS (Sudden death syndyronme) on galaxy phones. I think that's what happened. I really don't know but I cannot flash anything without needing pit file.
keithh85 said:
Yes to all 3.... I read something about SDS (Sudden death syndyronme) on galaxy phones. I think that's what happened. I really don't know but I cannot flash anything without needing pit file.
Click to expand...
Click to collapse
Can you post what it says on Download mode screen? Also, is it OTA update from At&t? If so may be it updated your bootloader version to 4.3. So, try to flash 4.3 rom (may be you can try stock).
Thanks for the reply, I will try a 4.3 rom
A_youu said:
Can you post what it says on Download mode screen? Also, is it OTA update from At&t? If so may be it updated your bootloader version to 4.3. So, try to flash 4.3 rom (may be you can try stock).
Click to expand...
Click to collapse
ODIN MODE (red)
Product name:
Current Binary: Samsung Official
System Status: Custom
Android guy
Downloading...
Do not turn off target!!
your other question...
A_youu said:
Can you post what it says on Download mode screen? Also, is it OTA update from At&t? If so may be it updated your bootloader version to 4.3. So, try to flash 4.3 rom (may be you can try stock).
Click to expand...
Click to collapse
Yes, AT&T kept telling me I needed to update. I would try to kill the screen but it would keep popping up over and over. So I finally let it download with the intention never installing it. I guess it did it without my knowledge.
PIT file....
I finally got ODIN to make some progress... But I do not know what to do from here. Picture attached.
keithh85 said:
I finally got ODIN to make some progress... But I do not know what to do from here. Picture attached.
Click to expand...
Click to collapse
Ok, Can you try to flash new stock rom? You can follow here - http://forum.xda-developers.com/showthread.php?t=2589891
Also, make sure that you don't flash "AT&T i317 ODIN 4.3 UCUBMJ4 (Leak) Bootloader & TZ (AT&T Note 2 ONLY)" bootloader as this bootloader is only for 4.3 leaded version.
Failed
A_youu said:
Ok, Can you try to flash new stock rom? You can follow here - http://forum.xda-developers.com/showthread.php?t=2589891
Also, make sure that you don't flash "AT&T i317 ODIN 4.3 UCUBMJ4 (Leak) Bootloader & TZ (AT&T Note 2 ONLY)" bootloader as this bootloader is only for 4.3 leaded version.
Click to expand...
Click to collapse
Same result... Here is the screenshot.
keithh85 said:
Same result... Here is the screenshot.
Click to expand...
Click to collapse
When Odin fails, are you getting any message on the phone itself? If you look in the top left corner it should display some information. Mine will usually give me a message when Odin fails.
phone screen
cameron213 said:
When Odin fails, are you getting any message on the phone itself? If you look in the top left corner it should display some information. Mine will usually give me a message when Odin fails.
Click to expand...
Click to collapse
No the phone never changes.
I'm "guessing" you may be having a problem with the ota bootloader. I've seen luck with this thread in restoring a soft bricked phone due to trying to flash from the ota 4.3 to the leaked 4.3:
http://forum.xda-developers.com/showthread.php?t=2581321
Might be worth a try. Hope it helps
flymacs said:
I'm "guessing" you may be having a problem with the ota bootloader. I've seen luck with this thread in restoring a soft bricked phone due to trying to flash from the ota 4.3 to the leaked 4.3:
http://forum.xda-developers.com/showthread.php?t=2581321
Might be worth a try. Hope it helps
Click to expand...
Click to collapse
I will give it a shot. I have nothing to lose at this point. I've been on an iPhone for 3 days now
flymacs said:
I'm "guessing" you may be having a problem with the ota bootloader. I've seen luck with this thread in restoring a soft bricked phone due to trying to flash from the ota 4.3 to the leaked 4.3:
http://forum.xda-developers.com/showthread.php?t=2581321
Might be worth a try. Hope it helps
Click to expand...
Click to collapse
I will try again but I see I already have that file on my PC. If I try to flash it, it fails and it says no PIT partition found. I am starting to think I have a hardware issue.
keithh85 said:
I will try again but I see I already have that file on my PC. If I try to flash it, it fails and it says no PIT partition found. I am starting to think I have a hardware issue.
Click to expand...
Click to collapse
Do you have pit file? If so try to give all files together in Odin -
pit file in "PIT" & select re-partition checkbox
ROM in "PDA"
and try to flash.
keithh85 said:
I will try again but I see I already have that file on my PC. If I try to flash it, it fails and it says no PIT partition found. I am starting to think I have a hardware issue.
Click to expand...
Click to collapse
Had posted a possible solution for you over on general then saw this thread...
http://forum.xda-developers.com/showpost.php?p=49378159&postcount=62
Includes link to the pit file
Hello,
I am unable to flash stock firmware back to my J200GU with Odin since it always gives me a fail.
So I was trying to flash directly on TWRP or ADB sideload but I always get an error with my zip firmwares.
Does anyone knows where to get the zip firmwares ready for ADB sideload or TWRP?
Sorry if it is a stupid question but I am really newb on this.
Thanks.
use noblerom/hydrarom meta-inf folder in your rom.
RevolverRz said:
use noblerom/hydrarom meta-inf folder in your rom.
Click to expand...
Click to collapse
I have tried what you recomended and TWRP proceeds to install hydrarom, however it is installed very fast and when it reboots i am stuck at bootloop. I believe it has sucessfully installed hydra but not the stock rom I wanted.
I have currently no OS on my phone or any firmaware so my guess is that to be able to install this custom roms (hydra and noble) i need to already have a stock firmware an this will be just an add on. Correct me if I am wrong.
Are the firmwares from SAMMOBILE ready to be used on TWRP? I am starting to think the are not to be used on TWRP but ODIN instead, but ODIN always gives me a fail. SO my question is: IS there a way to make roms downloaded from SAMMOBILE install on TWRP or adb sideload? Any guide about this?
Thanks. I appreciate any help since I have my J2 completly useless now
Can you post your Odin log?
or use the 4 files repair firmware.
https://www.androidfilehost.com/?fid=24407100847293886
RevolverRz said:
Can you post your Odin log?
or use the 4 files repair firmware.
https://www.androidfilehost.com/?fid=24407100847293886
Click to expand...
Click to collapse
Just tried the repair files and got this error on ODIN:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any more suggestions?
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
Means this rom is not for you j200gu.
Use the most recent version of rom from here..
http://updato.com/firmware-archive-select-model?q=SM-J200GU&rpp=15&order=date&dir=desc&exact=1
pic upload edit
This is my phone. It was bought in Thailand and its dual sim. I am not sure which is the correct firmware for my phone since its dual sim. Can anyone guide me?
RevolverRz said:
Can you post your Odin log?
or use the 4 files repair firmware.
https://www.androidfilehost.com/?fid=24407100847293886
Click to expand...
Click to collapse
Thank you! Finally!
I have tried flashing using just the AP file instead of all 4 files and it worked. When I tried to use the 4 files together in Odin it failed but instead using only the AP I was able to install the firmware and get a PASS.
Thanks alot for all the help in this forum
sushyoshi said:
Thank you! Finally!
I have tried flashing using just the AP file instead of all 4 files and it worked. When I tried to use the 4 files together in Odin it failed but instead using only the AP I was able to install the firmware and get a PASS.
Thanks alot for all the help in this forum
Click to expand...
Click to collapse
Glad to hear that
FRP/FAP Locked
RevolverRz said:
Glad to hear that
Click to expand...
Click to collapse
I accidentally turned off the oem unlocking in dev options(couple of hours earlier) and then when i tried to change my emoticon pack it says FAP Lock. Thank you so much!!! :good: :highfive: (I use Samsung J200GU)