[Q] need help with microp issue!!!! - Touch Pro2, Tilt 2 Windows Mobile General

alright so i was driving, someone cut me off, my tilt2 fell off the center console into a cup of soda.
when i pulled it out i had the screen with the red, blue, green, yellow or whatever.
so i updated my driver on my computer cause im using vista, then i did a hard spl flash to put it back to the stock version. i left it plugged into my computer with it on the att world phone screen and it stays on that for about 10 minutes and then finally starts up, everything comes up fine including my previously loaded background but i get the apparently popular microp wrong version 0 message saying it needs to be updated. btw once it loads everything has extreme lag. i keep seeing that its a hardware problem but some people seem to fix it doing another hard spl flash (which ive tried and didnt work). now if it is a hardware issue, usually its from people dropping their phone on the ground hard or whatever, but would it be that from falling 8" into a drink (also heard htc makes their stuff waterproof???)
bottom line is the phone is still under warranty, but under my friends name who i bought it off of, do you think ill still be able to get it repaired under warranty or am i just screwed and have to buy another phone? or does someone have a solution to this problem?

Waterproof? Not even close! Whoever told you that is dead wrong. I think Motorola has a new phone that is very moisture resistant, that you can submerge it. But that phone is very unique in that regard. Cell phones are not typically waterproof, or even water resistant in any way. Dropping the phone in soda is absolutely the cause of your issue, and its a hardware problem.
Warranty will do you no good, unless your friend paid extra for the type of insurance that covers damage that you caused. There are moisture sensing stickers inside the phone (change color when they come into contact with moisture). Warranty service will know from these that you have water damage (in addition to soda being inside the phone!). They will charge you for the repair or a new phone.
Your best bet is to turn off the phone, take the battery out, and dry the phone out as much as possible. Some people put their moisture exposed phones in a plastic bag with rice, which is supposed to help dry it. Or put in a warm place (some say on top of the refrigerator). Dry it out for a few days, then try to power up again. Since you dropped it in soda, it may be a goner, since there is other gunk inside your phone now besides just water.

MicropERROR Microp version mismatch 0 Please update last microp firmware
Someone solved this problem to HTC Touch Pro 2 T-Mobile RHOD210?
it appears without get water.

vsouza said:
Someone solved this problem to HTC Touch Pro 2 T-Mobile RHOD210?
it appears without get water.
Click to expand...
Click to collapse
You create a new thread, and bump an ancient one?!?

Related

Phone freezes up when idle

If I leave my phone on and come back to in about an hour it becomes unresponsive. The screen is won't come on, usb won't work and the power button doesn't work as well, but the lights still flash. All I can do is take the battery out and turn it on again.
At first i thought the keypad must have been getting disabled after a certain amount of time for some reason, but since the usb the connection alos dies when it's idle it must be something else.
I've been having this problem for awhile now. It first it started every once and awhile, but now it's getting to the point that I have to reset it every hour or so.
I just upgraded my ROM to Kavana 080408, but I've had this problem running the T-mobile WM6 ROM as well, therefore I'm guessing it's a hardware issue?
Any thoughts, questions, or help is greatly appriciated!
call tmobile and ask them to send you a new phone... its hardware issues...
Thank you. Err.. the only thing I haven't mentioned (for lack of mistaking the problem) is that just 3 days ago I dropped my phone outside and it rained the next morning. When I recovered the phone it was soaked.. I let it dry out and it worked again.
I think the incedent had to have been irrelevant, because I have been having this problem for about 8 months regaurdless, just not as severe.
Would T-mobile be able to know it got wet at some point and not exchange it because they'd assume the problem was due to water damage?
Well if you look under the battery to the right where the sim card goes, there is a litmus paper that turns purple/pink when wet and its white originally. I would just remove the paper if it is purple/pink and try to cut and glue a white piece of paper the same size. And then I would call them and tell them.
Glue and fish strips?
Thanks, but hmm.. how exact should this be? I was thinking about going to the fish store and buying some test strips and using those. Then i was thinking about thinning out some glue and using that to stick it. Does this sound good? I'll post how it goes.
Dash Arrived then Died
I just got my dash about two weeks ago. Before I could start finding my way around, it began acting strangely. It would not respond and sometimes suddenly cut off on it's on. Then it got to the point where it would not turn on right away. I would have to play with it (battery and SIM removal) and then it might turn on. I thought I was using the power button incorrectly.
Finally, the dash would not turn on at all. Since it was new and insured I requested a replacement. T-Mobile insisted that I test it with a alternate battery (I had a charger stand + battery on order but it had not arrived yet.) Since it would still not turn on via USB or power adapter (no charging lights either) I was certain it was not the battery. After arguing with a T-Mobile Rep and Supervisor I finally decided to lie (er um exaggerate) and tell them I had tested an alternate battery.
Before the new phone arrived the charger and spare battery arrived. I tried both batteries in the new phone with no problems.
You may want to try and get a new phone but the T-Mo rep definitely asked me the color of the paper strip inside the battery housing. My rep told me that it would change color if the LCD was damaged or cracked but I checked another phone (Samsung T409 and Motorola V188) and based on the locations of the strips I would assume it's a water damage test strip.
You may also want to see it you can remove a strip from an older phone.
Good luck!

[Q] Water damage

Only had my desire a few weeks, and yesterday I did the stupidest thing I could. I dropped it in a cup of tea.
It wasn't fully submerged and only the bottom quarter of the phone was affected.
The water indicator sticker on both the battery and the phone are still white, unless there are any more stickers located inside the phone which I don't know about.
I attempted to try it with a hair dryer and lightly shook out most of the tea. I left it to try for as long as I could and removed the battery and sim card, but foolisly I did attempt to turn it on afterwards, as I needed to use the phone. (Which I've now read I shouldn't have done).
Most of the tea went under the area which you can only get to if you unscrew the phone, which if I unscrew will void the warranty completely, so I have left it on for now.
The power button on the phone no longer works, and the phone boots up straight away when the battery is placed in it. The phones main features work, but if I don't constantly use the phone and the screen switches off, it completely shuts the phone down.
As the indicators are still white, do you reckon there is any chance I could get it repaired under the HTC warranty?
Sorry for the long rambling explanation, and advice would be greatly appreciated.
how long ago did it happen? cover it in rice and chuck it in your hot water cupboard for a few days. that usually gets rid of all water inside water damaged phones (of course all bets are off now that you have tried turning it on).
Becca-720 said:
Only had my desire a few weeks, and yesterday I did the stupidest thing I could. I dropped it in a cup of tea.
It wasn't fully submerged and only the bottom quarter of the phone was affected.
The water indicator sticker on both the battery and the phone are still white, unless there are any more stickers located inside the phone which I don't know about.
I attempted to try it with a hair dryer and lightly shook out most of the tea. I left it to try for as long as I could and removed the battery and sim card, but foolisly I did attempt to turn it on afterwards, as I needed to use the phone. (Which I've now read I shouldn't have done).
Most of the tea went under the area which you can only get to if you unscrew the phone, which if I unscrew will void the warranty completely, so I have left it on for now.
The power button on the phone no longer works, and the phone boots up straight away when the battery is placed in it. The phones main features work, but if I don't constantly use the phone and the screen switches off, it completely shuts the phone down.
As the indicators are still white, do you reckon there is any chance I could get it repaired under the HTC warranty?
Sorry for the long rambling explanation, and advice would be greatly appreciated.
Click to expand...
Click to collapse
any chance of warranty repair - sorry to say, but probably not.
the tea will most likely have caused some staining internally, so it's gunna be pretty obvious it's got wet.
try the rice thing mentioned by nzdcoy, but I don't fancy your chances.
i am sorry to say but any kind of warranty is lost. the only way for you to manage to get your phone fixed is to be disassembled. take a look here
http://www.mediafire.com/?na3g62068gvbg96
and here
http://www.mediafire.com/?ecyzwbvqefcjiuw
this are disassemble and assembly videos.
forgot to mention, for cleaning it use isopropilic alcohol. you can find it in any phormacy.
if you can't find it use pure 95% white alcohol.
regards
Marios

My evo is about to go through the wall

Short Version: Phone worked, Sat for a month, doesnt get past cyanogen screen goes into protect mode.
Okay i bought an evo that had the screen replaced on it. The guy obviously didnt know what he was doing. So I dropped it one day and the digizer ripped off.( the flex cable ripped, The digitizer wasnt stuck down) So a month later, i finally got around to buying a brand new housing for the entire thing. I took the mobo out and put it in the new housing. It worked for about 5 minutes then gets stuck in a boot loop. I had it happen once, before i got the new housing, It took me 5 minutes to get it to work again. The phone would shut off randomly sometimes.
It worked fine before the screen broke off no major problems would shut itself off every 2 or 3 days. The board has sat in a bag on my table for a month and now it wont work.
Now i cant even get the phone to stay on at all. The cyanogen screen shows up it loads and then shuts right off (i have recovery) I have tried different kernels,roms, and radios. The phone goes into protect mode now. Can I hit with a heat gun and reflow the cpu like a ps3 or xbox? Is there anyway i can remove all hardware failure protection?
ma777 said:
Short Version: Phone worked, Sat for a month, doesnt get past cyanogen screen goes into protect mode.
Okay i bought an evo that had the screen replaced on it. The guy obviously didnt know what he was doing. So I dropped it one day and the digizer ripped off.( the flex cable ripped, The digitizer wasnt stuck down) So a month later, i finally got around to buying a brand new housing for the entire thing. I took the mobo out and put it in the new housing. It worked for about 5 minutes then gets stuck in a boot loop. I had it happen once, before i got the new housing, It took me 5 minutes to get it to work again. The phone would shut off randomly sometimes.
It worked fine before the screen broke off no major problems would shut itself off every 2 or 3 days. The board has sat in a bag on my table for a month and now it wont work.
Now i cant even get the phone to stay on at all. The cyanogen screen shows up it loads and then shuts right off (i have recovery) I have tried different kernels,roms, and radios. The phone goes into protect mode now. Can I hit with a heat gun and reflow the cpu like a ps3 or xbox? Is there anyway i can remove all hardware failure protection?
Click to expand...
Click to collapse
You have any insurance? Depending on how your morals are you could try to make a warranty claim on it (although after todays announcement I might feel bad considering theyre trying to help us out). Otherwise I would try flashing an RUU and if that doesnt work take whatever means necessary, although Im not sure why your mobo would be damaged after a month, have you tried cleaning it and blowing on it to get all the dust out?
My recommendation is to make sure you stretch first, then when you do throw the phone through the wall, that you make sure it's a wall that's going to be easy to repair.
Reading your post it looks like you bought a phone that was practically guaranteed to have problems.
You bought the phone equivalent of a lemon, so expect the same amount of effort into keeping this thing alive as if you were to buy a car lemon.
short of running an ruu or smashing it and saying you 20lb sledge fell from 20 feet and landed on it lol
I've never looked into something that says "protect mode" for an EVO.
However, most electronic can do this if the thing is going to over-volt. If you think about car amplifiers, they do the same thing and go into protection mode which means that capacitor or something much more is bad.
I agree with the other guy and that you threw yourself into a bad deal from the start so it's as if you're going to be fixing something that's already inherited potential issues.
Have you considered that the replacement screen may be the culprit? Aside from the potential drop damage that could have broken something on the logic board, the another possibility is that the hardware you just installed could be defective and causing the EVO to do this protect mode.
In any event, the best solution would now be to work with a company to get a diagnosis of the problem. If you get a diagnosis only, you can buy your own parts and do it yourself if you're like a McGyver type-a-guy.
Find a credible cell phone repair shop and just get an diagnosis first.

Condensation Hard Freeze, Reboot on Home Screen.

Hello
I just purchased a GSM Galaxy Nexus From Google last monday. Got it on wednesday the first thing i did was put a screen Protector on it before booting the phone up.(ArmorSuit MilitaryShield) The phone work great on Thursday no issues what so ever. Then i Friday i went to the gym. Kept the thing in my pocket and wiped my hands before touching anything on the phone. (Waiting for otterbox to arrive)
I as soon as i get out i notice Condensation in the front camera. I soon as i received a text my phone hung up and reboot itself. After loading again to the home screen it hung up again as soon as text pop up again. I after 8 tries i final was frustrated. Took the SIM card out and swipe to the right with my finger to try to see if i could unlock it to the home screen.
I was finally able to get into the phone and turn on airplane mode before it hung up again. After i did that i Sut down phone and put the SIM card back in. Repeated the the same steps. As i turn airplane mode off the phone hung up again! (Seems everyone in the mother had to text me at that moment) I was able to make two phone call's before it lock up, but i couldn't hear them and they couldn't hear me. Called 611 then i was able to hear at&t computer but sound like the speaker was dieing. Then the phone lock up and reboot itself.
So i go into the boot loader. The phone was functioning perfected in the boot loader. Play with it for about 10mins. No hangs up. I found that weird. So i reboot the phone was able to get myself into the Factory reset. After that i did a hard factory reset.
So i call Google and they sent me over to Samsung. Samsung wants to do a replacement. I don't mind doing that i just don't like the fact they need a CC number just in case they have to Charge if the phone was abuseded which it wasn't. Baby the hell out of it. They asking me if the phone came into any touch with liquid. The the only thing i could think of was the solution the screen Protector Company sent. I didn't spray the solution directly on the phone but the direction told me to spray couple of sprays on the side of the SP that was going on the screen. (2 Sprays).
The Samsung rep told me the systoms don't sound like water damage. So after getting off the phone (About 1 hr) i notice the condensation was disappearing from the lens. So i took a quick blow dryer to it for about 30 secs. Turn the phone back on and everything been rock solid (Expect for wifi cutting in and out for some reason) for about 2 days.
So tomorrow Samsung fiance department will be calling me for my CC info. My question do you think i should send it in ? Do you think they will find water damage? Was this water damage ? Does the GSM galaxy nexus have Water Sticker ? I'm not able to find one. (Every where i googled no one had a direct answer)
I'm not trying to rip Samsung off i just don't want this to happen down the road again. If it was water damage ill just deal with it i guess.
I wonder if i don't open the new phone tey send me and just use my old 3gs in till i hear back from them... will i be able to send the Replacement phone back if it was water damage ? Just pay the shipping costs? First time dealing with something like this
What do you think i should do ?
Thank you for any input.
Sorry for the wall of text.
Just Notice i posted this in the wrong section My bad ill ask for mod to move it.
Look at the water contact indicator under the battery and see if it is red. A wet apply screen protector should not have caused this, but be careful to not let water get in the speaker and crevices when applying. In the future if your phone does come in contact with water or condensation remove the battery and sim Immediately and place in dry rice for 24 hours, do not try to power it on. Many others are reporting wifi instability, check the threads for solutions.
WiredPirate said:
Look at the water contact indicator under the battery and see if it is red. A wet apply screen protector should not have caused this, but be careful to not let water get in the speaker and crevices when applying. In the future if your phone does come in contact with water or condensation remove the battery and sim Immediately and place in dry rice for 24 hours, do not try to power it on. Many others are reporting wifi instability, check the threads for solutions.
Click to expand...
Click to collapse
Edited.
Looks like your good to me, I don't see any red.
WiredPirate said:
Looks like your good to me, I don't see any red.
Click to expand...
Click to collapse
Do you think Samsung will find anything ? Sorry for all the questions. The lens on the front camera was white. Is there stickers inside the phone where the CPU is
I heard there was like 3 water indicators in the phone.
That I couldn't tell you, I've never taken the phone apart so I would only be guessing. You might could find out by looking for a "tear down" of the phone, there should be several online if you do a Google search. Is the phone continuing to function well for you? Besides the wifi?
Yeah its been running great. Just got off the phone with Samsung. I think i just keep this phone. I don't want to pay for repair cost's. If the phone dies in month then i guess it was water damage. I hope there's no corrosion on PCB. I would love to take it apart but i don't want to void the warranty to check. Is there warranty Sticker in there ?
The wifi thing might be my fault. My laptop does that sometimes too. I'm just freaking out. I love the phone. I don't want it too die. Just ran a CPU stability test for about 15mins. No errors the battery was at 42c temp. Went ahead and sut the phone down. Going to wait 15 mins then turn it back on.

Blank screen after phone got damp

Hey all,
Had an account here before but forgot my password and no longer have the email . Anyway, my phone got damp while out on a cycle ride last night. At first the screen was working and then it started to appear slightly green and had horizontal lines across it. Now the screen is completely blank. I left it in a bag of rice all night but no luck.
Just taken the back off again and had a look. In the very top left of the phone 2 of the pieces of solder on the back of the screen seem to have just fallen away after being wet. Is there any hope of repairing this, or do I need a new screen piece? If so where would I get one?
Also, it is still under warranty with my contract provider, I don't suppose they would repair it without figuring out it got wet?
Cheers
It's unlikely you'll be able to repair it under warranty as there are indicator stickers that change colour when they get wet, and technicians check them upon admission into warranty. To be honest, if you've left it in rice and it still hasn't fixed itself, you're SOL. It's hard to tell where the damage occurred and it may be the screen or the actual logic board. You COULD give repair a try (DIY or non-warranty repair) though it may be pointless as it might not be your screen that's actually broken and/or other parts may be broken as well.
Unlawful said:
It's unlikely you'll be able to repair it under warranty as there are indicator stickers that change colour when they get wet, and technicians check them upon admission into warranty. To be honest, if you've left it in rice and it still hasn't fixed itself, you're SOL. It's hard to tell where the damage occurred and it may be the screen or the actual logic board. You COULD give repair a try (DIY or non-warranty repair) though it may be pointless as it might not be your screen that's actually broken and/or other parts may be broken as well.
Click to expand...
Click to collapse
Does the fact that it still essentially works (sound, touchscreen, vibrate, I can still blindly click on apps etc.) spell hope that it's only the screen that works? Might give it to someone who has some electrical skills to see if they can repair it... If that fails I don't wanna drop £130 on a new screen only to find that something else is broken!
EDIT: Also, when connected via USB the whole filesystem is intact.

Categories

Resources