Develop Bugs

HOW TO: Flashing Titan 3.35.04 Radio

Posted here for XDA-devs.com Vogue users. Copied and pasted from this thread created by jakdillard.
INSTRUCTIONS (added by mindfrost82...written by JD):
First you have to have a 3.xx rom loaded
I did not have my sdcard in when I did this so maybe you shoud take yours out to.
Next you have to use the .40 unlocker to downgrade the spl (DOWNLOAD HERE)
- Be in your current ROM with an active ActiveSync session, then run this unlocker and follow all of the prompts
Then you load the titan radio DOWNLOAD HERE into a ruu folder then flash
- Do the power-camera-reset to get to the tri-color screen - it should say 0.40 unlocker ImCokeMan.
- You must have the RUU already downloaded, then extract the radio until that folder and flash.
Your device should boot normally showing the radio as 3.35.04 and the rom as 3.04.
Once the device comes on showing the information connect it to you pc when the device boots up it will come to the welcome screen.
DON'T tap the screen to get started instead wait for active sync to recognize the device.
Next run the 2.31 unlocker follow all of the steps when it is done your device will reboot (DOWNLOAD HERE)
This time when it does its ok to disconnect and go thru the getting started process or load the new Hybrid ROM with the new drivers.
- Download the new Hybrid ROM (DOWNLOAD HERE).
- Do the power-camera-reset to get the the tri-color screen (should say 2.31 unlocker ImCokeMan).
- Flash the new ROM as usual
Warning if you do not downgrade the spl the radio rom will not load Also if you do not relock the device with the 2.31 bootloader it will cycle reset on you untill you do relock it

mrnamster said:
First you have to have a 3.xx rom loaded
Click to expand...
Click to collapse
Just starting to look into this... So... What exactly is a "3.xx" ROM?

The new Rev. A and GPS ROMs use the 3.xx radio. Their version numbers are also 3.xx.

Need Help "unbricking" my friends phone

Friend got a vogue but he "bricked it" he doesnt even remember what he did,
he is very new at this and looks like he did a rom update without doing a radio update first.
i have an HTC titan but i am going to buy this vogue off of him if i can fix it.
so here is the issue...
when u start the goes it goes to the 3 color tri-color boot screen...
it goes right there without even me holding down the power and camera buttons.
i used mtty to get it out of that screen... i do set 16 0 and some other thing i can't remember for the life of me now in mtty
i reboot the phone and now it get the a custom Dette clean rom 6.1 splash screen but it says no Radio and it now just stuck there.
i tried to load the stock rom on a 2 gig fat32 formated flash card and inserted it into the phone. then boot it to the 3 color screen, and it just says no file! in gray backbground then goes back to the tri color screen...
i made sure the name was correct.. i tried "Voguimg.nbh" i tried "voguimg." and just "voguimg" then i tried it in all caps and then all first letter cap then rest lower case...
it is spl-2.01.1000
i think my friend flashed the rom without upgrading the spl as well.
i tried to flast it with sp 2.31 but i couldnt get it to load it. i guess i can't flasth to 2.31 in the tri color screen...
any ideas? any help would be greatly apreciated. spent about a week on this... probably about 2 to 3 hours reading and reseaching daily.

Duplicate msg

I even tried to stock vogue roms (this is a verizon phone)
but i tried even the following sprint stock roms:
RUU_Vogue_SPRINT_WWE_1.12.651.1_2.13.00_SPC_NV133_Ship.exe
this gets me to 1% then errors out
and says error 328 invalid command, this update utility can not be used with my phone. please check my update utility... wat
RUU_PPST_Vogue_SPRINT_WWE_3.03.651.2_Radio_3.42.30_AM_NV_2.04_Ship.exe
this one stays at 0%
tried the verizon stock rom...
which stays at 0%
i dont know if the spl has something to do with it but i read the first file i mentioned the stock rom 1.12... reloads the spl, boot loader, everything to original.

I noticed when I first flashed my phone, also xv6900, that when I was unlocking, I didn't fully complete it, and it showed SPL version 2.10, or something along that line.
There is no stock VZW ROM available, so that's a waste of time. I think the first problem is, you have no idea how it got that way. I'd assume your friend didn't complete the unlocking process, then ran the RUU for the new ROM.
I'm not 100% sure, hopefully someone can either correct me on this, or confirm.
You should be ok since you can enter the bootloader. Perhaps you could try relocking it, you would use ImCokeMan's relocker, should be SPL version 0.43. Then you could try unlocking again.
I'd suggest checkin at PPCGeeks, asking in either the general Vogue flashing threads, or try asking ImCokeMan himself.

i will try .43, i am trying .41 but it keeps saying no device connected would you like to try copying again?
on this screen :
*
* Vogue/Sprint Touche CID unlocker utility
*
* Total process may take about 5-10 minutes depends on CPU speed.
*
Connect your device via activesync before continuing.
Press any key to continue . . .
Initializing..

wow fixed it. it wsa something so simple. must do quick format rather than full format on the mirco sd card....
meh

chewbaaka said:
wow fixed it. it wsa something so simple. must do quick format rather than full format on the mirco sd card....
meh
Click to expand...
Click to collapse
Good to hear! For future references could explain step by step what you did to solve it?
Thanks!

actually i thought it was working... but now it is stuck at the
"Loading... " screen
i have verizon... using a verizon signed ruu
when i use a sprint signed ruu it says
Loading...
then in 2 seconds... it says
Checking...
then in a few seconds it says....
Not Allowed...
then goes back to the tri- color screen
ill let it stay at Load... and then goto sleep and see if it finished tomorrow morning before football starts

unbricking ur phone
Unbricking Vogue / and downgrading SPL
--------------------------------------------------------------------------------
Edited *This will help those that are stuck at the HTC welcome screen and cannot get past it to load IMCokeMan's Unlocker.**
Edit by ImCoKeMaN: If you are stuck in bootloader (3 color screen) use titanexitbl or mtty (set 16 0 then task first and try these steps only if that doesn't work.
Apparently you can not use SDHC cards with this method, please use the 512mb card that came with your phone.
I have successfully unbricked my phone due to updating the Alltel rom to a non Alltel Vogue, before IMCokeman had released his unlocker an also have downgraded to the previous SPL version. I will shortly update this post with the How to instructions. I just need to retrace my steps.
I would first like to thank IMCokeMan for his help and unlocker.
I currently have a Sprint Vogue but I assume this will work for all versions
For those that had loaded the Alltel rom without the unlocker and have bricked there phone try this procedure to unbrick your phone.
1. First download IMCokeMaN's 2.31 Unlocker. http://rapidshare.com/files/11019074...r_MFG_2.31.exe
2. Extract IMCokeMan's unlocker
Previous SPL version was 2.31 current SPL version is 0.36
Edit by ImCoKeMaN:
Note: Steps 3, 4 and 5 should not be necessary, but step 6 is critical that it is a signed rom from your carrier
3. Navigate to the extracted folder and within the folder you will find the following file called VOGUIMAG2.nbh and rename it to VOGUIMG.nbh
4. Copy the file to a fat32 memory card, and insert it back into your phone, and place it into bootloader mode.
5. The phone should display Loading... let it sit there for a minute or so. It will not go past this screen, now reboot the phone.
6. Extract your official rom using WINRAR by right click and extract files (Must be a signed EXE from your carrier get it from HTC support website)
7. Navigate to the extracted folder and within the folder you will find the files
8. Copy the files to your memory card (less than 2gb and formated fat32) and insert it back into the phone and place it back into bootloader mode(POWER+CAMERA+RESET USING STYLUS), and install the your Carrier's Official ROM.
I have attached the VOGUIMG.nbh file for those that are having problems.

patelaquib said:
Unbricking Vogue / and downgrading SPL
--------------------------------------------------------------------------------
Edited *This will help those that are stuck at the HTC welcome screen and cannot get past it to load IMCokeMan's Unlocker.**
Edit by ImCoKeMaN: If you are stuck in bootloader (3 color screen) use titanexitbl or mtty (set 16 0 then task first and try these steps only if that doesn't work.
Apparently you can not use SDHC cards with this method, please use the 512mb card that came with your phone.
I have successfully unbricked my phone due to updating the Alltel rom to a non Alltel Vogue, before IMCokeman had released his unlocker an also have downgraded to the previous SPL version. I will shortly update this post with the How to instructions. I just need to retrace my steps.
I would first like to thank IMCokeMan for his help and unlocker.
I currently have a Sprint Vogue but I assume this will work for all versions
For those that had loaded the Alltel rom without the unlocker and have bricked there phone try this procedure to unbrick your phone.
1. First download IMCokeMaN's 2.31 Unlocker. http://rapidshare.com/files/11019074...r_MFG_2.31.exe
2. Extract IMCokeMan's unlocker
Previous SPL version was 2.31 current SPL version is 0.36
Edit by ImCoKeMaN:
Note: Steps 3, 4 and 5 should not be necessary, but step 6 is critical that it is a signed rom from your carrier
3. Navigate to the extracted folder and within the folder you will find the following file called VOGUIMAG2.nbh and rename it to VOGUIMG.nbh
4. Copy the file to a fat32 memory card, and insert it back into your phone, and place it into bootloader mode.
5. The phone should display Loading... let it sit there for a minute or so. It will not go past this screen, now reboot the phone.
6. Extract your official rom using WINRAR by right click and extract files (Must be a signed EXE from your carrier get it from HTC support website)
7. Navigate to the extracted folder and within the folder you will find the files
8. Copy the files to your memory card (less than 2gb and formated fat32) and insert it back into the phone and place it back into bootloader mode(POWER+CAMERA+RESET USING STYLUS), and install the your Carrier's Official ROM.
I have attached the VOGUIMG.nbh file for those that are having problems.
Click to expand...
Click to collapse
these instructions do not seem to work me.
he has a sprint phone... he assumes it works for all types but i have a verizon phone... and on a signed verizon nbh file ... it only says loading... and gets stuck there... on step 6... and a sprint rom says loading.. and then says checking right away and then says not allowed in red and goes back to the 3 color screen.
also the poster of this mentions he has spl 2.31... my spl says spl-2.01.1000 which is not .40 .41 or 2.31 (the most comment spl's i have seen referenced)
has anyone ran into these conditions? spl 2.01... stuck, and has verizon.
mine was originally stuck at the 3 -color boot screen... even after taking battery out and putting it back in and just powering on without holding camera-power keys... it goes into the boot screen only...
so i used mtty did set 16 0 and then "boot" and now when i restart the phone it goes right to the splash screen and gets stuck there saying dette's clean rom ... but "no radio" and just stays there.

[Error 226] My phone is brick ?

Hello,
After a flash of GenY 1.1 by MTTY (and internal storage) the flash stop at 71% with a 226 error.
Now I can't flash HardSPL (flash goes to 100% but the version of my HSPL in bootloader still the same !). I can't flash on official rom (stop at 61% with same error code).
Anyone now if it's possible to do something for that ?
Thanks
PS : sorry for my english !

I can never change my hardspl without using the jumpspl technique as in link below for hardspl 1.24
http://forum.xda-developers.com/showthread.php?t=408621
It always stays the same despite reaching 100%
HTH
Bixx

Try:
http://forum.xda-developers.com/showpost.php?p=1518700&postcount=11

Hi !
I've tried to flash HSPL 1.24 but like my phone doesn't boot, I can't copy and execute JumpSPL.exe and the RomUpdateUtility can't flash the HSPL.
JR_de > i's for the trinity, the 1.20 Olipro it's not for diamond, and I'm no SuperCID.
I've tried with 1.40 Olinex Unsigned with mtty command in your link but still the same error when I flash an official rom (2.03.406....)
thanks for your answers

try to change the usb port from pc and still try yr phone is not brick

I try with another usb port, and another computer, the results it's the same !

tom62 said:
I try with another usb port, and another computer, the results it's the same !
Click to expand...
Click to collapse
ever tried to change the usb cable?

Yes I try to flash with a second usb cable....
I believe there is no solution !

OS?
On what OS are you trying this?
Windows XP / Vista / 7 32bit? 64Bit?

Try this: http://forum.xda-developers.com/showthread.php?t=578231

is there a bootble ROM on it?
if so , download a stock image from HTC and copy to top level of your 4GB
reset and press the enter and back buttons
follow on screen instructions
i recomend that you flash like this, much safer
good luck

hello, happy new year everybody !!
there is no bootble ROM on my diamond.
I have no access to the internal storage, I can't copy a nbh file on it.
I try to flash an hspl with change .nbh after click on the first "next" in the customRuu, but the version of the hspl always doesn't change, and error 260 when I flash an OS rom...

nobody has a solution ?!

Try and flash back to stock SPL, check my sig
after that, try and flash stock OS
if either fail, send to HTC
Good Luck
Badwolve1

Need A Guide To Hard Spl Without Active Sync!

Dear Expert!
I'm Looking for a guide how to Hard SPL Diamond To Onilex or anything with bootloader mode Because My Htc is stuck with The Touch Diamond Screen and won't boot at all! Thanks It have the original spl!

too easy .. rename the ( *.NBH ) file to ( diamimg.NBH )
- copy it directly to the internal storage
- hold down VOLUME + reset your phone
- follow the steps.

......................

.. rename the ( *.NBH ) file to ( diamimg.NBH )
- copy it directly to the internal storage
- hold VOLUME down and back arrow + reset (keep holding volume down and back arrow)
- follow the steps... will tell you to press power button to begin.

Ahem.. he says he doesnt even have hardspl installed.
For as far as I know you can only install HSPL with the RUU included.
Did you try to flash a custom ROM without HSPL?

the hardslp is also a nbh...

Yes but if he flashed a custom ROM that wont boot without HSPL his Diamond is probably bricked..

Flash a Stock Rom from Bootloader tu "unbrick" your Diamond and get a somewhat "defined" state.
The other way is to boot into the bootloader and flash HArdSPL from there.

Help on a MDA III

Hi, i'm trying to put a shady rom on my mda compact III, but i'm a new at this, I already downloaded the rom but now I dont now what to do, can anyone point me in the right direction or explain me step by step how it's done.
I hope someone can help me

I will assume you have an SDHC card and SD flashing is not an option
prepare for first flash:
- remove SD card and prefferably even SIM
- charge battery to at least 50%
- connect cable with ActiveSync (or WMDC), so that you can access files on your device
- make sure you use a reliable cable to prevent dropouts in midflash
get your ROM:
- download a ROM you want to try, if it's not official HTC, you NEED HardSPL before you continue
flashing HardSPL:
- find HardSPL ( get arteUSPL-nosize-cmon.zip somewhere around here, try google )
- HardSPL comes with no flashing program, you need to steal one from another ROM first!
- Unpack the ROM you chose in previous step and delete its .NBH file, place the RUU_Signed.nbh from HardSPL to the folder with blank flashing program
- make sure you are still synchronized and connected, you can alternatively switch to bootloader (hold rec until tricolor screen, press softreset)
- run the flashing process with CustomRUU.exe or similar (it has an icon)
flashing ROM:
- make sure the numbers on device start say SPL 1.11cmon otherwise try HardSPL bit again
- sync ActiveSync or use bootloader mode
- unpack the ROM you chose again OR just delete the HardSPL NBH file and place the original you deleted back
- run the EXE file and flash
- perform a hard-reset after the flash to prevent random problems (hold left+right softkey and press softreset)
-put your SIM and SD back
Have fun
I hope it's not too complex and I'm sure you can find better guides somewhere around here but this works. I think xD

Thanks...
You help me a lot.