Hi all,
I wanted to put a new ROM on my Touch Diamond p3700, and managed to bust it.
I followed the MTTY guide from here
http://forum.xda-developers.com/showthread.php?t=416211
I got through the steps OK, but at some point, after restarting the device I noticed that it stop booting.
It would display only TOUCH diamond, and that's it. No other red numbers with RGD.
I tried a hard reset. Nothing. I also did a hard reset with a moviNAN format, and nothing. (though I think this might have made matters worse)
I tried a RUU, and it stays at 0% for a couple of minutes and then gives an error on the PC.
I tried an original ROM, but it says Not allowed for this Vendor ID (goes up to 1%).
I tried Hard SPL 1.24 a couple of times but this also stays at 0% for a couple of minutes and then gives an error.
I am totally out of ideas, but I'm only an extreme beginner, so I do hope there will be a solution.
Any help would be greatly appreciated.
Thanks.
check ur pm. provide me a complete update report btw. from 1-infinity what you did...
jus one question though. did u do hard spl after mtty and BEFORE flashing?
ayyu3m said:
check ur pm. provide me a complete update report btw. from 1-infinity what you did...
jus one question though. did u do hard spl after mtty and BEFORE flashing?
Click to expand...
Click to collapse
This is a board and not a private chat. A solution should be discussed in public, so maybe later, someone will find this and solve the problem. He will never find your PM... Do you understand that?
guythomaz said:
This is a board and not a private chat. A solution should be discussed in public, so maybe later, someone will find this and solve the problem. He will never find your PM... Do you understand that?
Click to expand...
Click to collapse
do a little more digging before you go on. this forum is cluttered with all sorts of "stuck in bootloader" requests and solutions. i only mean to save this clutter and in the process atleast even a kb on the servers of this forum..
these things have been discussed in the open and in full disclosure. but still some ppl find it hard to do search. i m saving this poor fellow from cluttering all over the forum and being bashed literally in the forum.
+ do ur research. i have replied likewise posts more than 2 times. so i think its best to go pm.
--->> and IF THE SCENARIO **IS NEW AND DIFFERENT from the typical "wrong rom wrong spl and stuck in bootloader" problems ** (which i highly doubt) and also if it is valuable to the forum i will post all my pm's related.
EDIT: See this post which was posted TODAY : http://forum.xda-developers.com/showthread.php?t=862690
Now you see what i mean? So hope YOU understand!
Did he put his phone in BL mode after MTTY? I guess this is the situation.
After MTTY please hold VolDown pressed while you press reset button. After BootLoader connect your phone to USB and flash your ROM.
Related
so i'm sure this has happened to someone..
i'm just hoping that i haven't bricked my F*ing phone, but i've scoured the forums but can't find any help.
I was trying to flash a new rom on, but for some reason it stopped in the middle, and now all i get is the rainbow screen... i can't flash anything else on there and have resorted to just taking the battery out for now in case i need to reflash later on
can anyone PLEASE point me in the right direction? I know all you chef's are busy, but hopefully can aide me w/ this as i keep looking
thanks in advance
You really need to check out this first:
http://forum.xda-developers.com/showthread.php?t=286755
Or this: http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
...and hopefully you have Hard-SPL installed.
yeah i checked and tried, but thanks.. i'm just gonna delete this thread and pray cingular will send me another one
not sure how, found an old method to unbrick it and it did.. now i'm not too sure what version spl or anything i have though... thanks for trying to help w/ the links guys
nnngggggnnnggggggg - trying hard...not...to let head.....explode!!
NOOOOOOOOOOOOOOOOOOO!!!!!!!!!!!
Anyway.....
Come on fella - it's people like you that are giving this site and others like it, a bad name! It takes about 6 seconds to go from not knowing anything about your SPL to knowing what it is and why you should have olipro loaded to stop you bricking your phone.
Please, for the love of god, I beg you to read the wiki and just a couple of things before you randomly try any more radio or OS ROM updates.
Hold the OK (left hand side) and power button whilst pressing the reset button on the bottom.
If it says anything other then 1.40.olipro - read the wiki before you turn your phone into a small, plastic brick. No...not fun-like-Lego.
DO IT NOW!!
Have you done it yet?
Well?
Have you done it now?
Lordsmiff said:
nnngggggnnnggggggg - trying hard...not...to let head.....explode!!
NOOOOOOOOOOOOOOOOOOO!!!!!!!!!!!
Anyway.....
Come on fella - it's people like you that are giving this site and others like it, a bad name! It takes about 6 seconds to go from not knowing anything about your SPL to knowing what it is and why you should have olipro loaded to stop you bricking your phone.
Please, for the love of god, I beg you to read the wiki and just a couple of things before you randomly try any more radio or OS ROM updates.
Hold the OK (left hand side) and power button whilst pressing the reset button on the bottom.
If it says anything other then 1.40.olipro - read the wiki before you turn your phone into a small, plastic brick. No...not fun-like-Lego.
DO IT NOW!!
Click to expand...
Click to collapse
... .... i have been sooo waiting for this......
"oy mate pull your head in...."
jk hope ur having fun and not completely exploded...
these people fet 2 u dont they
oh n soz re gramma n spellin
... r we avin fun yet
aahh something happened when i tried to flash a rom on my universa, i connected it to the pc, and started the proccess as allways, but.. it stucked at 7% and then error!!! and now i cant flash anything!! what can i do???
Isaygarcia said:
aahh something happened when i tried to flash a rom on my universa, i connected it to the pc, and started the proccess as allways, but.. it stucked at 7% and then error!!! and now i cant flash anything!! what can i do???
Click to expand...
Click to collapse
AND theres an error, 112 Update error can anyone help me??
help please!!
Quihubole paisano! Sorry, even if I speak spanish, this is an english forum so...
If you haven't had any answer yet is because that question might well have been answered several times, you have to be patient and search the forum and the wiki, even if I have never had that problem (fortunately) it is somehow "common", there are several methods, involving sometimes the need of getting the PDA in bootloader mode, attaching it to the PC and using a serial communications program (such as hyper_terminal), also if I remember well, the great MAMAICH have it's own method, so, look out, dig, read, lose your sleeping hours and good luck!
After that, if you're still having problems you will certainly propose a better question that someone might answer...
Animo
Hey thanx!! i think its bricked, now i need to unbrick it.. it can help because it can be posted on WIKI! and may be usable as well for all..
Ok slow down we need a bit more info
What rom did you have before
What exactly did you do
And witch rom did you try !!
ok step by step.
I was happy a sunday morning, and i was reading this forum lala.. Happy..
then...
i saw a rom ... that rom was WM6.1 http://forum.xda-developers.com/showthread.php?t=365335
i flashed it.. it worked fine but i had so low memory.. then i continued reading that thread, and found that someone changed the pagepool and gained memory, and i downloaded the modified version.
well, when i tried to flash it.. the phone just got unrecognized by the pc (when it tried to enter the bootloader with the RUU, as allways) and became nonresponsive... then i did a reset.. and nothing.. then i did a hard reset... and nothing... and then... i entered to Bootloader manually, and it worked... and i started the flash... but... when it reached the 7%.. it stoped and typed "ERROR 112: CE ROM UPDATE ERROR" and it happens with every single rom i try to flash...
i got some conclusions, maybe the SPL or something has corrupted the rom settings, but i dont know how to fix it.. can you help me?
HEY!! many thanx.. the problem was solved with mtty method, but with another code...
many thanx..
i will put the method here in a while (breathing DEEP)
Hey mate, as i told you in that thread, those 2 methods in wiki, they work
Congrats, mate.
Isaygarcia said:
ok step by step.
I was happy a sunday morning, and i was reading this forum lala.. Happy..
then...
Click to expand...
Click to collapse
, i liked the way, you explained it.
Ok. The way i solved the Problem was the MAMAICH method, wich is:
1. Enter Bootloader.
2. Disable Async (task manager, end task)
3. Connect Universal via USB (in bootloader mode)
4. Run mtty (found in wiki)
5. In mtty, write USB on the left corner (it says COM1)
6. Press OK button on the right upper corner.
7. A window should appear, press enter, after that, you can see a "USB>" thing.
8. Write "task 28 55aa" (without quotes).
9. A process appear on screen (nothing in the Universal)
10. Well done, now you can flash any ROM again.
Thanx for all those who helped me. n____n
@rohitsharman: haha yeah..
[How To] Flash KS20 Complete Guide + Programms !!!
OK, I have really grown tired of people "crying" and wasting forum posts asking how to flash a rom, how their device can be recognized in LGMDP etc.
THERE ARE SOME MANY FREAKING GUIDES AND HELPFUL POSTS!
So I have created my own fully(I believe ) understandable guide on how to flash,brand,unbrand phone and restore .nv2 !
You can ask any question you want,nag to me,swear me,etc. I really like helping people!So please do not post in Spocky's or Farah's Threads for how to flash their roms!Everything you need is here!
***I am not responsible if you brick your phone or your dog dies ***
Guide Information:
www.mediafire.com/ibanezman192
If you appreciate my work,you can buy me a coffe!
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=RBB5HSMJGCWGE
great, I will check it out and try it.
Thanks, man.
You are welcome
When flashing my KS20 in emergency mode, after ~10 sec the LGMDP said something about an QCSBL writing error, or somethint li that. I pressed OK too early
Now my phone doesn't work, can't turn it on and no emergency mode. What can I do now?
Take out the battery,insert it and do a hard reset.
help...
hi ...i have a problem with my ks20...i'd installed application from htc, opera browser build for wm6.1 or 6.5...at first it worked but after soft reset my phone dont open anymore...it stock on the bootloader showing lg icon only...is there anyway for me to hard reset my ks20...please help if somebody knew or experienced this....thanks
algabz said:
hi ...i have a problem with my ks20...i'd installed application from htc, opera browser build for wm6.1 or 6.5...at first it worked but after soft reset my phone dont open anymore...it stock on the bootloader showing lg icon only...is there anyway for me to hard reset my ks20...please help if somebody knew or experienced this....thanks
Click to expand...
Click to collapse
1)Wrong thread.Please do not post irrelevant things.
2)Download my guide and you will see how you can hard reset.But I cannot understand why your phone hungs up!I do not think this has to do with opera.I have opera and it works fine.
Help! My LG KS20 is dead!
I have tried searching, but nothing came up.
Yesterday while flashing, it said something timeout (1st time the bar runs across)
Now, I cannot activate emergency mode. I cannot charge the phone. There is no response, no light. Charging the battery full has no effect. Taking the battery out has no effect too.
Is there any way to fix this? My warrenty expired just yesterday
ryanswj said:
Help! My LG KS20 is dead!
I have tried searching, but nothing came up.
Yesterday while flashing, it said something timeout (1st time the bar runs across)
Now, I cannot activate emergency mode. I cannot charge the phone. There is no response, no light. Charging the battery full has no effect. Taking the battery out has no effect too.
Is there any way to fix this? My warrenty expired just yesterday
Click to expand...
Click to collapse
Very strange problem!Maybe your battery is dead Take out the battery and connect the mobile with the pc.If nothing happens then it is not a battery problem.Have you tried a correct hard reset?By saying correct, I mean holding the 3 buttons for many time until the leds flash and then flash out.Then you must release the buttons.
Thanks ibanezman for your reply...
Nope, nothing. Battery is fully charged (I have an external LG charger that was given free).
Nothing happens when I remove the battery and connect to computer. I cannot do a hard reset, because there is no LG logo, and no lights. Not green, red, or blue.
I can't flash in emergency mode, because holding down Internet Explorer and Power gives nothing. No usual green light. Laptop doesn't detect anything. Nothing in device manager.
Today while going through the logs in the LGMDP folder I came across this.
<AppName>Log For Web DownLoad</AppName>
<TIMESTAMP>20090908235324</TIMESTAMP>
<Date>2009-09-08</Date>
<Time>23:53:24.-473</Time>
<IMEI></IMEI>
<TIMESTAMP>20090908235324</TIMESTAMP>
<RESULT>FAIL</RESULT>
Notice there's no IMEI number? Could this mean anything?
ibanezman192 said:
Very strange problem!Maybe your battery is dead Take out the battery and connect the mobile with the pc.If nothing happens then it is not a battery problem.Have you tried a correct hard reset?By saying correct, I mean holding the 3 buttons for many time until the leds flash and then flash out.Then you must release the buttons.
Click to expand...
Click to collapse
I do not think this has to do with IMEI.Maybe you have lost your IMEI in the flashing process.But I believe your phone is dead/bricked
I really cannot feagure out any other suggestions.Maybe you should take it to LG Service.
ibanezman192 said:
I do not think this has to do with IMEI.Maybe you have lost your IMEI in the flashing process.But I believe your phone is dead/bricked
I really cannot feagure out any other suggestions.Maybe you should take it to LG Service.
Click to expand...
Click to collapse
OK thanks ibanzeman. I think i will just let the ks20 go and buy a new phone.
Anyway its old already, and i think i bricked it. Thanks for your assistance anyway!
ryanswj said:
OK thanks ibanzeman. I think i will just let the ks20 go and buy a new phone.
Anyway its old already, and i think i bricked it. Thanks for your assistance anyway!
Click to expand...
Click to collapse
I'm sorry I couldn't help you, good luck finding a new phone!
thanks man. i will give this guide a go!
ibanezman192, thanks a lot for this very detailed guide!
hibjibis said:
thanks man. i will give this guide a go!
Click to expand...
Click to collapse
spuke said:
ibanezman192, thanks a lot for this very detailed guide!
Click to expand...
Click to collapse
The pleasure is all mine New version of the guide is coming tomorrow
erm.. can someone help? my computer doesnt seems to recognise my KS20 during Emeregency mode
I have same problem. On Win 7 64 bit, LGMDP do not see KS20.
What is the message that appears?
Link don`t work
Hi,
I try use the link for download the archive, but the link dot work....
You can fix this??
Thanks
PS: sorry for my english, but i am not very good in this language
Hi I have and IMATE PDA2k EVDO and I tried a d-two rom and I now have the device sitting on the 4 color screen every time I reset it. Any idea how I reset it back to defaults so I can load another image onto it, I have the original image. any advice would be appreciated.
Thanks,
Actually I just fixed it.
Anyone know of any WM5,6 or 6.5 roms that work on this phone. The EVDO network is dead here in Australia so I just want to convert it into a PDA.
For the love of God... if you are going to make a thread saying "Hey guys, I broke this, how do I fix it?" Do not EVER update with "I fixed it!" without telling us HOW you fixed it.
I thought it was such simple fix it did not requiere explaination. To enter the bootloader you do the following
Press Power + record (above the volume slider) + softreset at the same time.
This puts it into the load mode so you can reflash.
problem with my xda iis
hi nid help... i followed the instruction on how to upgrade my ppc but it seems that the download link for win 6 does not exist anymore and now im stock in the boot loader i think the screen only shows "serial and below shows v2.07" i cant use my phone anymore i tried to reset it and emove the battery but stil it only shows serial... hope you can help me guys tnx...godbless
jayreyes_31 said:
hi nid help... i followed the instruction on how to upgrade my ppc but it seems that the download link for win 6 does not exist anymore and now im stock in the boot loader i think the screen only shows "serial and below shows v2.07" i cant use my phone anymore i tried to reset it and emove the battery but stil it only shows serial... hope you can help me guys tnx...godbless
Click to expand...
Click to collapse
about WM 6 rom, maybe you can look at ftp://ftp.xda-developers.com/BlueAngel/Shipped_Complete_Updates/
or at http://shipped-roms.com/index.php?category=windows mobile&model=Blue Angel
try to flashing rom again
You sir are an idiot.
A Blue Angel rom will not work for a Harrier.
So delete your comment because some other idiot will follow your bad instructions then **** up their phone and make another idiotic post.
Yea so did anyone figure out this whole problem with the white boot loader screen? I'm no where near a programmer or anything but I think my boot loader version is out dated. My HARRIER, not blue angel, is stuck at a white screen that reads Serial(USB when connected to usb of course) and v1.02. I've had a Harrier before this and it had the four color screen for boot loader. Am I on to something here?
Oh btw I already tried to reflash the rom over and over but updater keeps saying it can't connect.
jayreyes_31 said:
hi nid help... i followed the instruction on how to upgrade my ppc but it seems that the download link for win 6 does not exist anymore and now im stock in the boot loader i think the screen only shows "serial and below shows v2.07" i cant use my phone anymore i tried to reset it and emove the battery but stil it only shows serial... hope you can help me guys tnx...godbless
Click to expand...
Click to collapse
I have the same problem, anyone found a fix?
yes I have too same problem..plz help
i have a problem
Obviously.
But which one?
Tell us as elaborate as possible.
Problems Blue Angel Harrier Alpine
B-44 said:
Obviously.
But which one?
Tell us as elaborate as possible.
Click to expand...
Click to collapse
Please be careful: This is a Blue Angel (BA) Thread!
As Hima and Alpine Fora are closed, i will try to help as well as possible,
but please post marked "off topic"- hope moderators won't intervene...
And always first work out which device you're talking about.
Still love Alpine...
@admin: I know it's quite impossible to keep all these legacy threads alive- but what about some rescue thread, e.g. for non-touch-screen-phones,the Hima-BA-Family?
As i know from Siemens/BenQ Phones, it has gone silent around here, but from time to time some collectors appear which shouildn't be left alone.
Hello HTC users, I have a big problem with my phone . Phone was Hard Bricked 15 days ago... Still looking for fix way...
When phone Booting - I enforced phone hard reset with key combinations... VOLup+volDOwn+power and then phone stopped working....
I think it's a %100 Software problem , but can't find any fix yet... any help?
My Computer See its under the name : qualcomm hs-usb qdloader 9008
Telephone Not Responding Anything...
s-on Phone
Stock Rom
J_15 cid
Not Responding Fastboot or adb
DUDE!
For the last couple of weeks, you've been posting this to multiple threads over and over and over and over and over and over and over and over again.
Your phone is indeed hard bricked. If you could fix it yourself, you would have had an answer telling you how to do so by now.
You have two choices:
#1: Send it in for repairs
#2: Buy a new phone
You may not know of the rules here on XDA, but you can read them here
Please take note of rule #5:
5. Create a thread or post a message only once.
As a large forum, we don't need unnecessary clutter. You're free to edit your message as you like, so if you do not receive an answer, revisit your message and see if you can describe your problem better. Not everyone is online at the same time so it might take a while before you receive an answer.
It's time for you to admit to yourself the obvious. You can't fix it on your own
manilafortuna said:
Hello HTC users, I have a big problem with my phone . Phone was Hard Bricked 15 days ago... Still looking for fix way...
When phone Booting - I enforced phone hard reset with key combinations... VOLup+volDOwn+power and then phone stopped working....
I think it's a %100 Software problem , but can't find any fix yet... any help?
My Computer See its under the name : qualcomm hs-usb qdloader 9008
Telephone Not Responding Anything...
s-on Phone
Stock Rom
J_15 cid
Not Responding Fastboot or adb
Click to expand...
Click to collapse
@manilafortuna
As stated before, xda will not tolerate spam post. Let this be a warning, do not open another thread about this issue or post this issue in someone elses thread. i see you have posted more than enough. please wait patiently for someone to help you if the can. This isnt a site for quick customer service report nor your personal diagnostic center.
thank you
Wolf
manilafortuna said:
...Phone was Hard Bricked 15 days ago...
...I think it's a %100 Software problem...
Click to expand...
Click to collapse
Clearly you don't understand how a hard brick works. No offense to you, and I hope you can learn, but please heed the other users' advice and do some research and stop spamming.
BlockOfDynamite said:
Clearly you don't understand how a hard brick works. No offense to you, and I hope you can learn, but please heed the other users' advice and do some research and stop spamming.
Click to expand...
Click to collapse
not Spamming... I will continue via this title...
manilafortuna said:
not Spamming... I will continue via this title...
Click to expand...
Click to collapse
There is nothing to continue, either send it in for repair or buy a new phone. It's not 100% software, it's properly bricked ! Please stop being so stubborn and take the advice.
Getting all the resources and information/effort to fix it "yourself" will at least be equal or cost even more than letting it done by HTC. Even a repair shop couldn't help you.......let it go
Edit :
Now you contacted me via PM, that won't help either. The thread you linked there is for a different phone, different partition layout, different files needed. That specific post was created in April.....and still hasn't found all the needed info and files that are required.
That's all i have to say about it. I think all the several posts and threads you created said enough and the 2 best options are given several times now.