Related
Hello, I cant follow/or understand the guides found here or in
trinityguides to recover my device.
I have successfully flashed severa cocked roms before, however this last one failed and left me in tri-color screen displaying SPL-9.99-CP
What do i need to do, my active sync want connect and give me the green OK.
It say it cant detect my device when i connecs it?
Please help, im not good at this, how can i get the device to be recognized by
active sync?
Any help very much appreciated!
allanredo said:
Hello, I cant follow/or understand the guides found here or in
trinityguides to recover my device.
I have successfully flashed severa cocked roms before, however this last one failed and left me in tri-color screen displaying SPL-9.99-CP
What do i need to do, my active sync want connect and give me the green OK.
It say it cant detect my device when i connecs it?
Please help, im not good at this, how can i get the device to be recognized by
active sync?
Any help very much appreciated!
Click to expand...
Click to collapse
In bootloader mode AS will not recognized the PDA. As I see there is DES crash proof hard-spl on your PDA. Stay in bootloader mode, and try to flash an other rom, or the original offical rom. If does not work here is a useful link:
http://forum.xda-developers.com/showthread.php?t=308691
thanks for your quick reply!
how can i flash without the active sync is connected?
i have tried but the rom update utility says it cant find device and exits
or can it be done withot connection, if so how?
thanks for all input, as i said im not an experienced "flasher".
I don't know why, but after successfull cooked rom update (Schap, Faman, etc..) the last one didn't work and stick to 3-color (I'm under olipro 1.3)
I just made a spl update without any pb (take a look if on your pda screen it shows USB instead of serial) don't care about activsync
Then a radio update (1.40 instead of 1.50).
Shap rom update didn't work anymore (cache issue), so I'd just copied RUU_signed.nbh from SChaps replacing the one into Fman folder, and just working fine...
If it can help you.
Had this kind of problem
Simplest thing is to load rom from SD card (do search on this).
In short get the ROM you want - ROM***.nb file and rename it as TRINIMG.NB put it on the SD card. Launch bootloader and follow instructions. Otherwise check thread VISTA FLASH DISASTER...
Good luck,
Solved!
I reconnected the phone ( it sad USB in the bootloader btw)
Downloaded schaps wm6pro and unzipped, enterd the ruu and flashed, even thoug active sync was inactive.
I didnt have to go any further than this.
Many thanks, now i might dare to try som more roms, done ax3ls and karmba's so far looking forward to test schaps now.
Look in the Trinity Wiki. It describe how to flash from the SD card. this will fix you up.
I tried to flash WM 6.1
and then Give me Error and now i have a black screen
any one can help me please!!!!
this would help
http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
best of luck..
i tried all of that but not working
What error is it ?
i treid to upgrade to windows 6.1 , while i'm updating gives me error and i tried to restart my mobile but nothing at all even i can not access the bootloader
Is your computer recognizin' your PDA. What happens when you connect it to the USB port ? Also, try after removin' SIM and the SD.
P.S: And you still need to tell me, what error msgs do ya get ?
my computer does not recognize my jasjar
I am so sorry what i remeber it was error code 101 , do you know i think the version that i tried to upgrade was not to universal
that's why this probelme happend.
I presume that you are tryin' to install the ROM designed for Universal
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
try this, or search xda-developers usin' google, you may find the solution.
Error code 101 is actually connection error.
hey, are you usin' Windows Vista
no XP SP2 , but as i told you i think i installed rom not for universal
also my screen is dead nothing at all only black no serial or usb on the screen
aahmed12 said:
no XP SP2 , but as i told you i think i installed rom not for universal
Click to expand...
Click to collapse
Oh man,
you have screwed up your phone big time. Post a thread in General Discussion> Upgrading, Modifying and Unlocking. Someone there might b able to help you out on this.
All the best.
i have a similar problem, but it just stucks on 7% of flash and then gives me an Error 112, i think it is the rom, and maybe it can be fixed with an eeprom flash or not? if it can be, can anyone give a how to do it?
Isaygarcia said:
i have a similar problem, but it just stucks on 7% of flash and then gives me an Error 112, i think it is the rom, and maybe it can be fixed with an eeprom flash or not? if it can be, can anyone give a how to do it?
Click to expand...
Click to collapse
hey bro, error 112 actually denotes ROM update error.
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
follow Method 2 , if it doesn't work, then follow Method 1, mtty may prove useful in this situation.
Good Luck..
thanks !
i havent tried the method 2.. but method 1 doesnt seem to work..
many thanx..
ok that methods doesnt work.. im stucked not in bootloader... i can exit bootloader but the system doesnt start... when i press the reset button it just keeps white screen (w/o backlit) and nothing happens.. if i connect the phone in that state just unrecognizes it and if i press the light and power buttons (without resset) it starts the bootloader.. its not reading the rom
every time that i try to flash a rom on it just fails, and it gets the error 112, on every 7%... how can i fix it?
Oops! I omitted the quote
aahmed12 said:
my computer does not recognize my jasjar
I am so sorry what i remeber it was error code 101 , do you know i think the version that i tried to upgrade was not to universal
that's why this probelme happend.
Click to expand...
Click to collapse
I have the same problem. I mistakenly flashed the wm6.1 rom meant for BA. I dont think there is any remedy for this problem because the unit is not coming on and so cannot enter bootloader. The only sign of life is the red led which means the unit is not seeing the power supply ie it does not recognise that a battery is instaaled. No one has ever come up with a solution. The unit is bricked fullstop. I am already bidding on another unit on ebay.
i did chat with imate support and they advice me to go to any service center and they will fix it.
i tried many kind of solutions but it does not work so my last choise is to send it to imate service center.
Hiya XDA
I've been trying all evening to get any HardSPL onto my Diamond without success, everytime I try I get to 0% and after a few minutes "error [260] connection" and the phone keeps its' black screen until I soft-reset it.
Can anyone help me get a hardspl onto my phone? I would really like to try WM6.5. I've read many SPL-guides already, so you don't have to point me to them
(even that on modmydiamond.info)
Thanks in advance!
esset said:
Hiya XDA
I've been trying all evening to get any HardSPL onto my Diamond without success, everytime I try I get to 0% and after a few minutes "error [260] connection" and the phone keeps its' black screen until I soft-reset it.
Can anyone help me get a hardspl onto my phone? I would really like to try WM6.5. I've read many SPL-guides already, so you don't have to point me to them
(even that on modmydiamond.info)
Thanks in advance!
Click to expand...
Click to collapse
Here's the Tutorial and here's the Troubleshooter. They're both stickies. Please search and read before posting.
Thanks for the quick response, but as I said. I've read all stickies and guides, and it's still stuck at 0%.
esset said:
Thanks for the quick response, but as I said. I've read all stickies and guides, and it's still stuck at 0%.
Click to expand...
Click to collapse
Did you let your device sync with Activesync/Windows Mobile Device Center?
Try recreating the sync pairing.
Try uninstalling the device from PC's Device Manager and reinstalling it and then try recreating the sync partnership.
Try another USB port.
Yes, yes, yes and yes. I even tried doing it on my laptop.
Edit: I even tried flashing down to 1.93 with HTCs official stuff, no success there either
esset said:
Yes, yes, yes and yes. I even tried doing it on my laptop.
Edit: I even tried flashing down to 1.93 with HTCs official stuff, no success there either
Click to expand...
Click to collapse
Another USB cable?
Try manually entering bootloader and connect to PC. The label should say USB not Serial and try from there.
esset,
May I ask what branding/model of the Diamond you own?
I own a pure AT&T model just purchased a week or two ago. And, so far I've also had almost zero luck flashing it. I'm moving from an AT&T Tilt which I've flashed so many times, the USB port is starting to wear down. I've also got a lot of experience with many small computing devices with all types of weird programming and flashing routines, so I'm not a newbie. But the AT&T Fuze just seems to be locked in a way that has yet to be covered by the good XDA folks here. Heck, I can't even dump the shipped ROM off the device to send it here for checking out by the developers. All I've been able to do is flash an odd 1.90 HardSPL that seems to have locked the phone even tighter than before. YUCK!
If you're in this same scenario, I'd suggest patience. Eventually someone with enough knowledge of these devices will be able to help out. It is frustrating though, after flashing the other phone so many times with so many different configurations to be held back on the new one.
tnyynt said:
Try manually entering bootloader and connect to PC. The label should say USB not Serial and try from there.
Click to expand...
Click to collapse
You might find this odd. The down-volume + back arrow key combo doesn't seem to work with some of the new versions of the Diamond. I've tried on two of them, and neither respond to this key combo at startup.
Many times entering the bootloader is not a problem though. The routine does cause the phone to go there. And, I can get it there by other means. Just not via the boot up sequence. This tells me there is something very different about these models....
I tried starting and flashing directly from the bootloader (showing USB), and the phone got to show a percentage field (the one when you are flashing) but same here, is constantly at 0% until the flashing utility times out and tells me to reboot my phone and guides me through steps if it has been semi-bricked (bootloader is the volume down + softreset, right?)
I bought my phone in the first shipment to Sweden, it's not locked to any company, bought it without subscription
Else I just flashed it up to latest ROM from htc.com (still no success with HardSPL ) to 2.03.413.2 SVE (02/06/09)
Radio: 1.09.25.23
Version: 52.51.25.26H
ninjaedit: (In the four-colored bootloader thing it says DIAM100 64M SPL-2.03.0000 MicroP-Diam (LED) v11)
Tell me if you need any other info :]
Here's another indication that the new phones are different. I've copied a DIAMIMG.nbh file to both a flash card inside the phone, and to it's internal memory. (sorry, but the thread on that location is confusing on what memory. I assume like most phones of the past that it's supposed to be the flash card, but "internal memory" is not a flash card.) But, the loader screen always responds with "no image file" when it's called up. So, is there a different name expected now?
put manual hardspl into your device, and click to it from your device..
zerocool81 said:
put manual hardspl into your device, and click to it from your device..
Click to expand...
Click to collapse
Tried that with every Hard-SPL linked to from this thread: http://forum.xda-developers.com/showthread.php?t=415191
Didn't work
Something's changed.
zerocool81 said:
put manual hardspl into your device, and click to it from your device..
Click to expand...
Click to collapse
Hi uhm, was that answer aimed for me or to scottwilkins?
If it was for me, is it possible to flash the mobile directly from the memory-card (or internal flash card)? Else if you mean the "manual make-the-screen-black-and-go-to-bootloader" my screen just goes blank, as when you do it with the RUU, and just stops there. Also seems like it looses the connection via USB doing so too. And flashing through the bootloader directly (volume down at softreset) shows the progressbar on the phone, but steadily at 0% (when trying to flash).
search and download
a) SDA_ApplicationUnlock.exe (Desktopprogram)
b) EnterBootloader.exe (ATTENTION: it must be that for diamond, normaly find by flashing-tools)
connect with active sync and copy EnterBootloader.exe to pda-root.
start SDA_ApplicationUnlock.exe on desktop and follow all but reset (DONT RESET)
start EnterBootloader.exe on pda
if bootloader-Mode and USB-Label than start flashing
wait for response
scottwilkins said:
Tried that with every Hard-SPL linked to from this thread: http://forum.xda-developers.com/showthread.php?t=415191
Didn't work
Something's changed.
Click to expand...
Click to collapse
try this.. put this file into internal storage and lounch this from ppc
http://rapidshare.com/files/207721836/SSPL-Manual.rar
okokur said:
search and download
a) SDA_ApplicationUnlock.exe (Desktopprogram)
b) EnterBootloader.exe (ATTENTION: it must be that for diamond, normaly find by flashing-tools)
connect with active sync and copy EnterBootloader.exe to pda-root.
start SDA_ApplicationUnlock.exe on desktop and follow all but reset (DONT RESET)
start EnterBootloader.exe on pda
if bootloader-Mode and USB-Label than start flashing
wait for response
Click to expand...
Click to collapse
I tried what you suggested, I successfully unlocked the phone (and did Not reboot it). Ran the bootloader; and the screen just went black, as usually, and nothing more happens
zerocool81 said:
try this.. put this file into internal storage and lounch this from ppc
http://rapidshare.com/files/207721836/SSPL-Manual.rar
Click to expand...
Click to collapse
That program makes the Fuze screen just turn black and do nothing. Cool, huh
Seems that the newer stock ROMS might be blocking something... hmmmm....
Well, crap!
I just figure out where my whole problem is...
The Fuze (my phone) = The Raphael
NOT the Diamond.
I just scrolled down the forum list, saw a phone that looked like mine and went there. DOH!
I feel like a total dumb-ass.
If I'd scrolled just a bit farther down the XDA forum, then I'd seen the Raphael phone.
Holy Cow! Go ahead, say it, I deserve it...
Thanks for all the help otherwise. It was a learning experience for me....
esset said:
I tried what you suggested, I successfully unlocked the phone (and did Not reboot it). Ran the bootloader; and the screen just went black, as usually, and nothing more happens
Click to expand...
Click to collapse
hi,
i think, you have the wrong bootloader.
i find this and try it by me self. this brings your fone definitly to bootloader.
than you can start manualy the hard spl by normal description way.
http://rapidshare.com/files/208123046/EnterBootloader.exe.html
okokur said:
hi,
i think, you have the wrong bootloader.
i find this and try it by me self. this brings your fone definitly to bootloader.
than you can start manualy the hard spl by normal description way.
http://rapidshare.com/files/208123046/EnterBootloader.exe.html
Click to expand...
Click to collapse
Thanks, but that file takes me into the bootloader, and when I start flashing the percentage is still at 0% until the software times out. Same as before, just the usual "going-into-the-bootloader".
Hello everyone!
I'm new at these forums, so excuse me if I'm being a "noob". I've searched all over the forums and found some instructions for my problem, but none of them helped.
My story is:
I have a T-Mobile MDA III device (I think it's also called HTC BlueAngel). It had the stock ROM, without any modifications. It was WM2003 I suppose.
I wanted to upgrade it to WM6, using this. In that thread it was recommended to use the updater given there, so I downloaded everything and tried to flash. After about 30 seconds of verifying information on the PDA, I got to a screen where it was supposed to say From and To version numbers, but everything was blank. I also have successfully flashed a HTC Trinity P3600 and those fields were blank there too, so I thought it's OK and pressed Continue. The program started to process, but after a while it said isn't designed for my device. I have tried numerous ROMs and RUUs to update it, but all of them gave some sort of error, some said "Congratulations, update complete" even if it didn't do anything.
The problem is, that my PDA is now stuck at the bootloader (?) screen. The backlight is off, the top of the screen says Serial (USB when cradled) and on the bottom I can see a version number (v2.05). I have read about key combinations (Camera, power, reset, record, etc) which are used to exit this state, but none of them worked. If I cradle my device, Windows (Windows 7, 64bit) recognizes the device as "Microsoft USB Sync", but WMDC doesn't see my device at all. On the forums I've read that in this state the device allows ROM updating, but I haven't found anything that could work, and the RUUs don't seem to recognize my device.
So if anyone has a ROM and updater that can work with this device, please link it to me, it's very important. I don't want to lose my PDA. If you haven't got a WM6 ROM, it can be even WM5, or even the stock ROM of this device, I just want to somehow revive it. Really, any ROM will do, just give me the proper updater and ROM. Or if you think the ROM wasn't erased from the device, please help me getting back to it.
JiGSaW_HTC said:
Hello everyone!
I'm new at these forums, so excuse me if I'm being a "noob". I've searched all over the forums and found some instructions for my problem, but none of them helped.
My story is:
I have a T-Mobile MDA III device (I think it's also called HTC BlueAngel). It had the stock ROM, without any modifications. It was WM2003 I suppose.
I wanted to upgrade it to WM6, using this. In that thread it was recommended to use the updater given there, so I downloaded everything and tried to flash. After about 30 seconds of verifying information on the PDA, I got to a screen where it was supposed to say From and To version numbers, but everything was blank. I also have successfully flashed a HTC Trinity P3600 and those fields were blank there too, so I thought it's OK and pressed Continue. The program started to process, but after a while it said isn't designed for my device. I have tried numerous ROMs and RUUs to update it, but all of them gave some sort of error, some said "Congratulations, update complete" even if it didn't do anything.
The problem is, that my PDA is now stuck at the bootloader (?) screen. The backlight is off, the top of the screen says Serial (USB when cradled) and on the bottom I can see a version number (v2.05). I have read about key combinations (Camera, power, reset, record, etc) which are used to exit this state, but none of them worked. If I cradle my device, Windows (Windows 7, 64bit) recognizes the device as "Microsoft USB Sync", but WMDC doesn't see my device at all. On the forums I've read that in this state the device allows ROM updating, but I haven't found anything that could work, and the RUUs don't seem to recognize my device.
So if anyone has a ROM and updater that can work with this device, please link it to me, it's very important. I don't want to lose my PDA. If you haven't got a WM6 ROM, it can be even WM5, or even the stock ROM of this device, I just want to somehow revive it. Really, any ROM will do, just give me the proper updater and ROM. Or if you think the ROM wasn't erased from the device, please help me getting back to it.
Click to expand...
Click to collapse
Remove the battery and look which model you have....
something like PH20B or the FCCID: xxxBLUEANGEL...
d-two said:
Remove the battery and look which model you have....
something like PH20B or the FCCID: xxxBLUEANGEL...
Click to expand...
Click to collapse
It says:
PH20B MDA III
FCCID: NM8BLUEANGEL
JiGSaW_HTC said:
It says:
PH20B MDA III
FCCID: NM8BLUEANGEL
Click to expand...
Click to collapse
Please look here for install the right driver for windows 7 64x
d-two said:
Please look here for install the right driver for windows 7 64x
Click to expand...
Click to collapse
Thanks, I've downloaded the PDFs and tried to follow the steps, but there were some problems.
The first strange thing I noticed was that the driver said it was already installed to my computer. I think that's not a problem, but still worthy to mention.
I have completed the driver installation, so I moved on to the ExtROM tutorial. Unfortunately this step failed completely, because it needs a working BA, and as I've said I'm stuck on the bootloader screen. Also I've tried to reflash the WM2003 that was in the tutorial, but it said that the Updater is not designed for my device. So I moved on to the final step, flashing - I downloaded the Updater and tried to flash the WM2003 you provided. I kept pressing Continue - but after getting to the last page, and pressing Continue for the last time, after about 10 seconds, the updater said Congratulations! The ROM have been updated successfully. But that was just a message, my BA acted like nothing happened. I'm still in the Bootloader and can't do anything. What am I doing wrong?
JiGSaW_HTC said:
Thanks, I've downloaded the PDFs and tried to follow the steps, but there were some problems.
The first strange thing I noticed was that the driver said it was already installed to my computer. I think that's not a problem, but still worthy to mention.
I have completed the driver installation, so I moved on to the ExtROM tutorial. Unfortunately this step failed completely, because it needs a working BA, and as I've said I'm stuck on the bootloader screen. Also I've tried to reflash the WM2003 that was in the tutorial, but it said that the Updater is not designed for my device. So I moved on to the final step, flashing - I downloaded the Updater and tried to flash the WM2003 you provided. I kept pressing Continue - but after getting to the last page, and pressing Continue for the last time, after about 10 seconds, the updater said Congratulations! The ROM have been updated successfully. But that was just a message, my BA acted like nothing happened. I'm still in the Bootloader and can't do anything. What am I doing wrong?
Click to expand...
Click to collapse
You have not read the tutorial right... you must install the driver manual!!!!
JiGSaW_HTC said:
Thanks, I've downloaded the PDFs and tried to follow the steps, but there were some problems.
The first strange thing I noticed was that the driver said it was already installed to my computer. I think that's not a problem, but still worthy to mention.
I have completed the driver installation, so I moved on to the ExtROM tutorial. Unfortunately this step failed completely, because it needs a working BA, and as I've said I'm stuck on the bootloader screen. Also I've tried to reflash the WM2003 that was in the tutorial, but it said that the Updater is not designed for my device. So I moved on to the final step, flashing - I downloaded the Updater and tried to flash the WM2003 you provided. I kept pressing Continue - but after getting to the last page, and pressing Continue for the last time, after about 10 seconds, the updater said Congratulations! The ROM have been updated successfully. But that was just a message, my BA acted like nothing happened. I'm still in the Bootloader and can't do anything. What am I doing wrong?
Click to expand...
Click to collapse
Can't you exit bootloader screen by simultaneously pressing power and reset?
Did you disable USB-Connection in activesync? Is important to do.
If update runs till "congratulations" in very short time (update usually takes about 10 minutes - estimated ), it seems like updater didn't see the nk.nbf file, which should be 32.769KB.
Please don't throw bricked phones at me, but- is the file unzipped? (note: i don't mean opened)
And: though d-two has given you the drivers for Win7 (and he's the one you can really trust he's got the right stuff) you may just try
another PC. Many people have trouble when trying to update with Win7. I still use XP.
B-44 said:
Can't you exit bootloader screen by simultaneously pressing power and reset?
Did you disable USB-Connection in activesync? Is important to do.
If update runs till "congratulations" in very short time (update usually takes about 10 minutes - estimated ), it seems like updater didn't see the nk.nbf file, which should be 32.769KB.
Please don't throw bricked phones at me, but- is the file unzipped? (note: i don't mean opened)
And: though d-two has given you the drivers for Win7 (and he's the one you can really trust he's got the right stuff) you may just try
another PC. Many people have trouble when trying to update with Win7. I still use XP.
Click to expand...
Click to collapse
If I press power and reset simultaneously, the screen goes dead for a second, then bootloader comes up again.
Tried disabling USB connection in WMDC (No activesync for Win 7), it changed nothing.
The nk.nbf is EXACTLY 32.769KB, so I don't know why it won't see it. With some versions it sees it but gives me an error 150 (RUU not designed for this device).
If by unzipped you mean extracted, yes, all the files (EnterBL.EXE, nk.nbf, MaUpgradeUt_noID.exe, etc.) are extracted to a folder, it looks the same as in D-Two's tutorial.
Unfortunately I don't have an XP PC. Will using a Vista laptop do any better, or should I use some kind of emulator of XP and update from there? If so, can you link me to one of those?
Sh*t.
Take out the battery for at least three days.
Then retry.
I lately had an VPA3 revived by this.
Always stuck in first step of bootscreen, already wanted to abandon it,
then after some days retried just out of some mood.
Worked.
XP emulator may be a good idea, but i'd have to google it the same way like you.
Because of my Siemens phones i haven't yet left original XP.
B-44 said:
Sh*t.
Take out the battery for at least three days.
Then retry.
I lately had an VPA3 revived by this.
Always stuck in first step of bootscreen, already wanted to abandon it,
then after some days retried just out of some mood.
Worked.
XP emulator may be a good idea, but i'd have to google it the same way like you.
Because of my Siemens phones i haven't yet left original XP.
Click to expand...
Click to collapse
he is not stuck at the 4 color screen he stuck in the bootloader mode..
If the bootloader mode active with software is he not wakeup after 3 days without battery or something else...
the BLENTER.EXE erase at adress 0x40000 the first 4 bytes and this will active the bootloader mode!!!
you must install the driver like in the PDF!!!
and than you can flash it with any rom!!
if you have install the driver correct it must like this...
sorry for my bad english
d-two said:
he is not stuck at the 4 color screen he stuck in the bootloader mode..
If the bootloader mode active with software is he not wakeup after 3 days without battery or something else...
the BLENTER.EXE erase at adress 0x40000 the first 4 bytes and this will active the bootloader mode!!!
you must install the driver like in the PDF!!!
and than you can flash it with any rom!!
if you have install the driver correct it must like this...
sorry for my bad english
Click to expand...
Click to collapse
No problem about your english, mine isn't perfect too
I realized what is the problem. When installing the driver manually, it says that the driver is not signed, and therefore I can't install it. I do everything the same as you did, but I fail at this step. I can't get it to install. Any solutions for this? :\ I'm starting to worry about this.
JiGSaW_HTC said:
No problem about your english, mine isn't perfect too
I realized what is the problem. When installing the driver manually, it says that the driver is not signed, and therefore I can't install it. I do everything the same as you did, but I fail at this step. I can't get it to install. Any solutions for this? :\ I'm starting to worry about this.
Click to expand...
Click to collapse
Reboot your PC and press before windows start "F8" and select the option "Start without driver signature" or something else...
I don't know what is the exactly word spelling in English i use my windows in German :laugh:
d-two said:
Reboot your PC and press before windows start "F8" and select the option "Start without driver signature" or something else...
I don't know what is the exactly word spelling in English i use my windows in German :laugh:
Click to expand...
Click to collapse
Found this option and I could install the driver You sent to me.
But the RUU still doesn't see my device. It acts the same as I was running it without my device.
JiGSaW_HTC said:
Found this option and I could install the driver You sent to me.
But the RUU still doesn't see my device. It acts the same as I was running it without my device.
Click to expand...
Click to collapse
have you use my updater?
d-two said:
have you use my updater?
Click to expand...
Click to collapse
Ignore my previous message. I just needed to reboot the computer. It updates now!! Thank you VERY VERY MUCH!! Finally I can use my PDA again Pressing Thanks button
Hello everyone, i have used this site for root another phones on past but now i can't understand how to fix my problem by myself. Thats why i'm here to kindly ask(beg) for help.
I tryed to root the phone, first i used the Framaroot, i thought it worked but look likes not, i'm getting the Secure booting Error! Couse: boot certification verify.
Ok, looks not a big deal, lots of guys got it and solved their problems with this post. But now is where i ask sorry because i couldn't make it.
I can enter on dowload mode, i tried all the steps on the post and did not worked. I need a light.
When i used the KDZ_FW, i got a message of error on extrating file.
When i tryed make a Recovery Hard Reset, i got the message Secure booting Error! Couse: boot certification verify.
When i try to turn it on by pressing the power + volumerdown = nothing happen.
I have a Optimus G E977, and the software was the E97710d.
Thanks for the attention.
http://forum.xda-developers.com/showpost.php?p=45355871&postcount=1
Question 5. I know it's hard to read before..i see things didn't changed around since i left. I see same lazy people,rushing into things before looking around....pffff....
Maybe U can help me too.
Everything was fine with my OG but problems start when installing CM11. I decided to go back to stock later (I did it) but then couldnt be able to enter recovery or download mode. I tried several methods like re root, unlock again and lately using ROM Manager and trying to install another recover all get screwed up. Only black screen. Trying and trying I could install KDZ firmware
So then I root, unlock boatloader with method one from here: http://forum.xda-developers.com/showthread.php?t=2667398
Ok i dont know if boatloader is unlocked now but i know I cant enter recovery or download mode. Im afraid to use freegee to try to unlock again.
What should I do.
Thanks
kimitza said:
http://forum.xda-developers.com/showpost.php?p=45355871&postcount=1
Question 5. I know it's hard to read before..i see things didn't changed around since i left. I see same lazy people,rushing into things before looking around....pffff....
Click to expand...
Click to collapse
kimitza said:
http://forum.xda-developers.com/showpost.php?p=45355871&postcount=1
Question 5. I know it's hard to read before..i see things didn't changed around since i left. I see same lazy people,rushing into things before looking around....pffff....
Click to expand...
Click to collapse
I appreciate your intention to help, maybe its because i'm a Braziliam guy, with not the best english, that i can't figure how to use the FREEGEE app if i can't start the cellphone.
Thanks again.
OBS: I have used that app too before get this error. And was just becouse tryed to enter on recovery mode that i got that message.
I understand that your celphone cant turn on or enter download mode or recovery?
If thats your situation maybe I can help U (I think)
Fuguets said:
I appreciate your intention to help, maybe its because i'm a Braziliam guy, with not the best english, that i can't figure how to use the FREEGEE app if i can't start the cellphone.
Thanks again.
OBS: I have used that app too before get this error. And was just becouse tryed to enter on recovery mode that i got that message.
Click to expand...
Click to collapse
Well, i'll try to explain all to not get missunderstood.
My situation is, without the USB cable the celphone don't respond to any button press.
With USB cable, by the momment that i plug it, the screen shows the error message.
With the USB cable and in the error message screen, i can press the volume buttons +- and power, after that the phone restart and shows the download mode.
What i know so far is, if i can enter download mode, and here is your words, all is not lost.
Knowing that, all solutions i found on this site doesn't work with me. Or, what is possible, i didn't make it right.
The phone do not enter on recovery mode.
I gess this is all. For now
Thanks for the patience to teach who needs to be teached.
ErnestoD said:
I understand that your celphone cant turn on or enter download mode or recovery?
If thats your situation maybe I can help U (I think)
Click to expand...
Click to collapse
My previous problem was far worst than yours.
I recommend U to uninstall all LG stuff from your PC and follow this guide: http://www.htcmania.com/forumdisplay.php?f=1026
Its in spanish so I think U wont have much problem
I did it yestesrday and save me. Whit it U will install a new KDZ firmware, even if it is bigger than 1GB
Good luck
QUOTE=Fuguets;51799238]Well, i'll try to explain all to not get missunderstood.
My situation is, without the USB cable the celphone don't respond to any button press.
With USB cable, by the momment that i plug it, the screen shows the error message.
With the USB cable and in the error message screen, i can press the volume buttons +- and power, after that the phone restart and shows the download mode.
What i know so far is, if i can enter download mode, and here is your words, all is not lost.
Knowing that, all solutions i found on this site doesn't work with me. Or, what is possible, i didn't make it right.
The phone do not enter on recovery mode.
I gess this is all. For now
Thanks for the patience to teach who needs to be teached.[/QUOTE]
As I see, if i'm looking for the guide you are refering, of install the original rom, is the same one that i already tried and i got message error of extract file.
I deleted all lg stuff from computer, downloaded everything of the guide and the message is the same.
Any more suggestion ?
PS: I prefer english version , at least to read is easy to me.
Edit1:I wonder if the fact of my kdz file be bigger than 1gb causes that ?
Edit2: When i try the guide on this link the step 7 does not show to me, and my phone or some similar does not show on the Usb Controler list to install.
Thanks again
ErnestoD said:
My previous problem was far worst than yours.
I recommend U to uninstall all LG stuff from your PC and follow this guide
Its in spanish so I think U wont have much problem
I did it yestesrday and save me. Whit it U will install a new KDZ firmware, even if it is bigger than 1GB
Good luck
QUOTE=Fuguets;51799238]Well, i'll try to explain all to not get missunderstood.
My situation is, without the USB cable the celphone don't respond to any button press.
With USB cable, by the momment that i plug it, the screen shows the error message.
With the USB cable and in the error message screen, i can press the volume buttons +- and power, after that the phone restart and shows the download mode.
What i know so far is, if i can enter download mode, and here is your words, all is not lost.
Knowing that, all solutions i found on this site doesn't work with me. Or, what is possible, i didn't make it right.
The phone do not enter on recovery mode.
I gess this is all. For now
Thanks for the patience to teach who needs to be teached.
Click to expand...
Click to collapse
[/QUOTE]
I didnt see that on XDA. I used this method with 2 kdz´s, one smaller and another one bigger than 1gb.
Maybe U missed something.
Fuguets said:
As I see, if i'm looking for the guide you are refering, of install the original rom, is the same one that i already tried and i got message error of extract file.
I deleted all lg stuff from computer, downloaded everything of the guide and the message is the same.
Any more suggestion ?
PS: I prefer english version , at least to read is easy to me.
Edit1:I wonder if the fact of my kdz file be bigger than 1gb causes that ?
Edit2: When i try the guide on this link the step 7 does not show to me, and my phone or some similar does not show on the Usb Controler list to install.
Thanks again
Click to expand...
Click to collapse
[/QUOTE]
Now I am really worried about that. I just can't acces the phone by any kind of way.
When i try the Unlock Botloader, it says that didn't found my device.
Now, after restart the computer, it says: The system cannot find the patch specified.
Is there no more options for me ?
The drivers I have downloaded here was automaticly updated from 8.0xx to 10.0xx, I unterstand this is a good thing, am I wrong ?
Could U flash KDZ using the method from htc mania?? (Im using it rigth now with 1.2GB KDZ firmware)
How did U come to that situation?
Fuguets said:
Now I am really worried about that. I just can't acces the phone by any kind of way.
When i try the Unlock Botloader, it says that didn't found my device.
Now, after restart the computer, it says: The system cannot find the patch specified.
Is there no more options for me ?
The drivers I have downloaded here was automaticly updated from 8.0xx to 10.0xx, I unterstand this is a good thing, am I wrong ?
Click to expand...
Click to collapse
I did that, while i use the KDZ one minute after start unpacking the file, it shows the error message and finish the procces. I don't know if is that what you were asking.
When I tried the button Read Phone Information, it tells me Emergency Not Support Batt Level Check.
Is that the problem ?
ErnestoD said:
Could U flash KDZ using the method from htc mania?? (Im using it rigth now with 1.2GB KDZ firmware)
How did U come to that situation?
Click to expand...
Click to collapse
Did U overwrite LGMOBILEAX folder was stated and (step 2). Did U edit hosts file as stated (step 3=
In my case i previously have a black screen, nothing more, but connecting phone to PC while pressing both volum keys aloud PC to recognice the phone.
If U receive extraction error that means that the patch is wrong. Do not press anything more in the program There is no need to
Fuguets said:
I did that, while i use the KDZ one minute after start unpacking the file, it shows the error message and finish the procces. I don't know if is that what you were asking.
When I tried the button Read Phone Information, it tells me Emergency Not Support Batt Level Check.
Is that the problem ?
Click to expand...
Click to collapse
I did not overwrite that folder, maybe we are looking for different guides because if that was something that i supose to do i didn't saw that on the guide.
I did not edit hosts file.
I restarted the computer now again, and now my message is: device not found.
Can you place the link of exacly guide i need to look ? Couse the link you send me before has a various of them.
ErnestoD said:
Did U overwrite LGMOBILEAX folder was stated and (step 2). Did U edit hosts file as stated (step 3=
In my case i previously have a black screen, nothing more, but connecting phone to PC while pressing both volum keys aloud PC to recognice the phone.
If U receive extraction error that means that the patch is wrong. Do not press anything more in the program There is no need to
Click to expand...
Click to collapse
http://www.htcmania.com/showthread.php?t=802175
Remenber to start from zero
Tested on WIN7 64 bits
ErnestoD said:
http://www.htcmania.com/showthread.php?t=802175
Remenber to start from zero
Tested on WIN7 64 bits
Click to expand...
Click to collapse
Helo again, i just finish the proccess now. Again i got the same message, I attached the log file, if you please have a look on that i appreciate.
I don't know, all the problem looks to be batterys fault. I hope not. Thanks.
Edit1: I foun this guide, do you think it could help me ?
But I didn't understand that well, looks like I need to be able to start the OS of the phone, which i can't.
Im sad to hear that , This is beyond my knowledge. It worked for me but...
Fuguets said:
Helo again, i just finish the proccess now. Again i got the same message, I attached the log file, if you please have a look on that i appreciate.
I don't know, all the problem looks to be batterys fault. I hope not. Thanks.
Click to expand...
Click to collapse
ErnestoD said:
Im sad to hear that , This is beyond my knowledge. It worked for me but...
Click to expand...
Click to collapse
What about my edit, where i found that someone said it solve the problem on 15%, do you think it could work ?
I just don't understant well, do I need to be able to start my phone rom ? Or i can do on my situation ?
Hello guys,
I am so happy that I wanted to share this with you. As I still have headache from googling how to flash back your stock rom (which didn't work out because the flash tool gave an error every time at 15%), I can save you a lot of headache with this very very simple fix.
For some people the tool works just fine, but when you have some google bootloader or a newer freegee unlocked one and you want back to stock, lots of people cant follow this thread because of the error at 15%.
The fix is EASY and I found it on the Optimus L9 section, thanks to that guy on XDA.
Follow exactly Davevinci's great thread except for one thing:
http://forum.xda-developers.com/show....php?t=2498102
Step 4 is now:
4.GO TO DOWNLOAD MODE POW+BOTH VOL BUTTON PRESSED+CONNECT USB
But step 4 should be:
- Boot up your phone in any stock based rom, for example SAVVY Rom V5
- Enable USB debugging and connect your phone through USB using the LG PC Suite option (make sure to kill PC suite in tast manager).
Now you should see the driver installation of LGE Android MTP device as usual and then just run the flash tool from the guide. Also de mode DIAG is now the right one. The flashtool will reboot your phone to download mode automatically when it's needed.
Still an error? Don't worry, disable virus scanner and firewall and just reconnect your phone. I got an error one time, during flashing, but I followed the steps the flashtool suggested me and now everything went fine.
Click to expand...
Click to collapse
The link U provide is not working and U didnt upload any log, I didnt see it.
As I read to perform that action u must be able to turn on your phone.
Did U try to flash a smaller then 1gb kdz or try another ones.
As U can see U wont receive to much help in LG forum. There are good guides but on time help is another thing.
Did U try this guide (method 1): http://forum.xda-developers.com/showthread.php?t=2667398
Is your phone properly detected in your PC?
Fuguets said:
What about my edit, where i found that someone said it solve the problem on 15%, do you think it could work ?
I just don't understant well, do I need to be able to start my phone rom ? Or i can do on my situation ?
Click to expand...
Click to collapse
I did not tried with a smaller archive because I can't download it. Among the Brazilian files I only can download the version 10D. I am on phone now but I will send the link that I'm trying asap. I really appreciate your help man. Even that I didn't found the solution yet is nice count with some experience help.
Enviado de meu XT1032 usando Tapatalk
Edit: From this list http://forum.xda-developers.com/showthread.php?t=2093382 , all brazilian links show Access Denied
And from here http://lg-phone-firmware.com/index.php?id_mod=20, only the V10D of Brazil.
I'm looking for the number 16, CLR/CLARO(BRAZIL) which is less than 1GB. Maybe i'm wrong, but when i clic on the name, a page of TNY shows a link of ADFLY that after i clic on close advertisement nothing happen.
About the method 1, I did try that, but sometimes it says "device not found" or "the system cannot find the patch specified". I'll try that from another computer, i let you know if i have some lucky. But the guy of the guide said:
!enable usb debugging
connect as MTP
follow the script"
Maybe its not for me.
Look what happen. (I'm using download mode)
*********************************************
* Tool Unlock BL Optimus G - Update 0414 *
* *
*********************************************
*** Select a number ***
1. UNLOCK BOOTLOADER
Seclect a number : 1
1. [Unlock] Optimus G JB 4.1.2 Selelct
Seclect a number : 1
FreeGee UNLOCK
Thanks to Team Codefire
1. JB 4.1.2
╣Seclect a Number : 1
1. KT
2. SKT
3. LGU+
╣Seclect a number : 1
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
Unlock BL success.
╕Reboot [y]/[n] :
About my phone get propper detected, i guess it is, at least on my devices map it shows "Lg AndroidNet Phone"