I took apart my dash to clean the inside. My camera wasn't working well so I thought it might fix it. Didn't really fix it, the software still freezes.
Anyway, the internal backup battery cables loosened from the connector way too easily... I barely even touched the cables. Now I can't seem to connect them back. It's way too fragile. I was wondering if I can get that part anywhere? The phone won't vibrate now... And I guess if I turn it off it just won't keep the time and date.
Maybe I should just get a new dash :/
You probably took the vibrator for the backup battery The vibration motor is flat and connected via a cable + connector to the board. It is located near the keyboard connector - usually the cable is wrapped around it. The vibrator connector can be plugged back to the socket.
Ha, it was the vibrating motor itself. I thought it's some sort of an internal battery.
I figured out how to connect the wires back. I took out the little plastic connector's legs out and was able to fit in the wires and push those legs back in.
Wasn't simple cause everything is so small, but after a few minutes I got it back working. Phone vibrates again
Related
My charger doesnt fit well and i just came to terms with this but it has got worse the last two weeks. It plugs in and the led lights up but it doesnt charge sometimes, it says it is charging but an hour later and the battery goes down 5% ish. Also it only connects when the phone sits face up and the cord hangs down as in it must sit on the edge of the table for it to charge. I tried my friends Droid cord and it was a snug fit. do i have an insurance claim on my hands?
You can try getting the cable swapped, but honestly I think the amount of hassle you would go through would just not be worth it. If the problem was with your phone then I would 100% definitely get the phone replaced, but if the problem is only with the cable, I'd take the path of least resistance and just buy a new cable out of pocket. They really aren't expensive if you know the right place to get them.
I use this cable here with my Aria and it works great: http://www.monoprice.com/products/p...=10303&cs_id=1030307&p_id=5458&seq=1&format=2
It is only $3.13 shipped (to my address), and it's 2 feet longer than the original cable which I like because I thought the original one was too short. Never had a problem with it charging my Aria. I know it seems too good to be true, but the quality really is just as good as a $20+ cable you'd find at a local store.
I ran into the same problem with an Aria I bought off of Craigslist. It would kind of charge at first, then it gave up altogether. I found that the end that plugged into the phone had been slightly squished by the previous owner. I just went to Staples and bought a Staples branded MicroUSB cable, it's six feet long and works fine. Granted, it wasn't ebay-cheap but I got the problem handled same day, no screwing around. The nice thing about this cable is it's just as flexible as the original, unlike the MicroUSB charge/sync cables that come with Blackberry phones and the extra length makes it a little more versatile.
Don't mean to resurrect an old thread, but I didn't want to start a new one.
My connection is getting worse every day. It is very aggravating. I'll plug in at night time and wake up to find my phone didn't charge at all. I have to put the cable in at a slight angle to get it to connect.
Using adb and just any file transfer on the computer is almost impossible.
I use the original cable, and sometimes my brother's Captivate cable--both are just as bad.
And the AT&T car charger is a joke. So I think it is the phone, not the cables.
i find that the motorola(backflip) usb doesnt fit snug(still charges & transfers fine, a little slower)
May be just a bit too rough with this little phone
Finally had enough of the cable problem, so I decided to figure out whats wrong. Turns out, I ended up pulling out about a cubic centimeter of dust and lint from in the port (way down in there, a quick glance and it didn't look as bad as it really was.)
Works like a charm, now!
Brivette, glad to see you fixed your issue!
For future reference,
The MicroUSB cable that has become the new standard contains 2 prongs on the end of it. This prong is responsible for ensuring it stays locked into the connector.
The newer MicroB connector is rated at a higher use cycle than the old MiniB type, which is why current devices are moving to it as a standard. It is also designed so that the cheaper cable will bear the wear and damage, rather than the device. The usual culprit is the two latch pins at the top of the male connector which tend to wear and bend eventually causing the cord to become "flaky" or fickle (for a lack of a better term). This is usually the cause of most people's woes. However often times the connections from inside the cable may wear and short out, causing the cord to become dysfunctional. Before sending your phone in for a replacement, I highly recommend trying a second cable.
If changing the cord doesn't work, the problem most likely lies with the phone. While it is possible that the PCB mount has come disconnected from the board, it is more often than not likely that the port has become clogged with debris. So before sending your phone in for service, check the port and ensure that the port is clear and clean of obstruction.
This also goes for charging or data transfer. Sometimes issues with data transfer can arise out of a bad cable. This often happens when people wrap their cord too tightly or kink it, which causes signal interference. It also occurs with frequent use and wear and tear, which is normal.
Take good care of your cord, and it'll be there to last you a long time.
A few month's ago I'd ordered a LCD screen replacement for my incredible, and so when I got back from work o immediately took out the LCD from the package and started taking out my old broken. For me it was my first time experience replacing an LCD phone screen, anyways back to what I was going to say was when I unplugged the connector for the screen and the motherboard itself, after attempt to plug the connectors back together; the display connector plugged in perfect while the connector for the motherboard didn't do so well. The white piece that covers the PCB Connector, it tears a little bit off and I'd tried to power on the phone, meanwhile it didn't I tried again and things got worst. So I search online for a PCB Connector and see one, so I decided to and try to rip off the PCB Connector and plan to order the PCB Connector. So the part to attempt ripping off the PCB Connector didn't go so well, and stop there before things got worst. Any suggestions how I can replace that? I can't just leave my phone in my room and have to cover in dust. I need my phone back, how can I fix these? I know this thread seems long but I tries but it details for you guys.
Hi,
Just wondering if anybody else has had any issues with the USB port. The centre of the USB port on my Tab Pro 10.1 has a flat bit that sticks out (like on all USB ports), only the plastic side and the metal side have come apart. When I first got my tablet it was sometimes difficult to plug the cable in, then the other day it wouldn't go in at all. I had to slip a nail file behind the metal bit that was touching the side, and push it back into the middle. I have to plug the cable in at a slight angle so it will go around that, and sometimes have to bend it back.
Obviously it can't stay this way, so I'm going to have to call Amazon and pray I don't get stuck without a tablet for weeks...
(it looks battered but that's just because of the close up, it looks perfectly new when you actually look at it)
Not sure what Amazon will do for you, prob better off calling samsung.
Does it still charge and transfer data? Make sure if ask by either that you send them better pic's
It still charges and transfers data, but only if I push the metal bit back into place regularly so I can plug the cable in. That is not a long term solution as that will eventually completely break the USB port.
Amazon are usually very good with defective devices, at least here in France, and will often just replace the device. Not sure about the tablet though, so I'll find out soon...
I have my phone plugged into the wall, lighter, or pc it will start charging. However, after several minutes it will start connecting and disconnecting itself, even when sitting on a table without any outside interference or touching it. This is with several different cable wires, chargers and even a dock. Anyone know if it's likely to be microUSB or a battery issue? It's unrooted and running stock KitKat.
Mine did the exact same thing, and would wake me up in the middle of the night with the beeping. Eventually, it stopped charging altogether, the night before I was supposed to go on a 400 mile road trip!
My solution was to clean the USB port on the phone. I used a product called DeOxIt and a small metal pick from the garage (I suppose a small paperclip would also work). Power down the phone, and remove the battery. Apply a drop of DeOxIt to the paperclip, and GENTLY scrub back and forth over the USB connector inside the phone (you'll need to get both sides - top & bottom). After that, unplug your charging cord, and apply a drop into the USB connector, and then work it in and out of the phone a dozen times. Let everything dry thoroughly, reassemble, and reboot!
I haven't had the issue since, and it's been almost a full year.
Hi everyone,
A few days ago, this problem started to show on my device.
When I'm charging it, it says "charging", but even the slightest movement can stop the phone from charging.
Sometimes it even toggles *charging*/*not charging* without me moving it at all.
For example, if the battery is on <15%, the phone will vibrate - so when I charge it when it's below 15%, if I touch it, it vibrates every 5 seconds or so.
It's really terrible... I once left the phone to charge for a few hours just to come back and find out it wasn't charging.
I've tried different USB cables, power sockets, chargers, so I guess it has to be a problem with my device.
I'm pretty confident it's a hardware issue, and I bought it around 10 month ago, so warranty should still be up. However, I don't remember anything particular that could damage the charging port, and this started all of a sudden (a day earlier it was charging perfectly).
I'd like to hear some opinions, solutions, and if any of you have had this before.
Thanks,
Barak
It's definitely the charging port, maybe it was faulty from factory, send it in warranty
Get a dress making pin or something tough and really pointy and carefully scratch inside the port. Be careful of the plastic inside. Do not bend it or snap it off. Do not scratch or pick at the pins on the top of the plastic. Only scratch around the plastic.
Shine a torch in and see if you can find any loose debris that you may have dislodged. Keep doing it until you can't get no more fluff etc out of it and try plugging the charger in again.
It should have a nice solid clunk as the plug goes in and seats properly now.
Hey, thanks alot for your replies. @shivadow I've tried cleaning the port like you said , this maybe helped a little but the problem is not solved.
P.S : I noticed that there is a position which is problematic.
When the phone is connected to the charger, if I hold the cable with my hand, and push it upwards (I exert force on the cable in a direction vertical to the screen). This is when it stops charging. Just stating this if it might help you diagnosing something specific.
Anyway I think I'll be sending it back to the lab this week or next week, thanks a lot for your help!
Either a faulty cable, plug or socket. If it happens with other cables it'll be the socket. If you know for a fact that the plug is seating correctly but you still have the problem then either worn pins or worn socket.
So it turns out that when I tried to check whether the charger, or the USB cable is to blame, I tried 2 different cables, but they were both faulty, which made me think the problem is with my HTC.
Now I tried changing phones and still had the same issue, so I tried more usb cables, and voila! Works like a charm
Thanks for the help @shivadow, much appreciated.
Always blame the cable first!