Develop Bugs

Flash error 262 Diamond

Hi,
I updated with success few time ROM usually Duttys 1.7 - 1.8 , i have installed HardSPL 1.4 Olinex yesterday i tried flash Duttys 1.9 its stop on 53 % and show flash error 262 IU 634 after that time i cannot flash any rom the stop on 58 84 % like TOR, PANOSHA, Please help !
Best Regards
Muzzzik77

This is error 262:
Q: During the upgrade, the progress bar is moving. If the error message (ERROR [262] :UPDATE ERROR) appears, what should I do?
A: This may occur when the connection is lost, without power supply, computer host is down, or due to other unexpected cases. You will see that there’s still one progress bar displayed on the device but it is not moving any more. The device cannot get into the Wince screen, so you cannot connect with ActiveSync. This problem usually can be recovered. You just need to follow the instructions in the error message box, reset the device, and run RUU again. RUU will re-flash the whole image again.
Note: You should remove the battery and reset the Mobile Device.
What you can do is reset the device with volume down key pressed. You will enter the bootloader. Check that at the bottom of the screen it says USB and not SERIAL.
If so, unplug the USB cable till it shows USB. Then flash it again. Maybe you should flash a stock HTC ROM first.
Good luck...

Muzzik77 said:
Hi,
I updated with success few time ROM usually Duttys 1.7 - 1.8 , i have installed HardSPL 1.4 Olinex yesterday i tried flash Duttys 1.9 its stop on 53 % and show flash error 262 IU 634 after that time i cannot flash any rom the stop on 58 84 % like TOR, PANOSHA, Please help !
Best Regards
Muzzzik77
Click to expand...
Click to collapse
try to flash an original rom signed like:
RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe
and remove the cover from the back of your device and keep it cooled with something(a vent or something)
is probbably that you have a power management issue on you device
if you got warranty u should take it to the shop with an original rom

i had the same ..
I used Hardspl a few weeks ago.
After 3 retry´s to flash the new WM6.5 HTC ROM,
i installed Hardspl relocker and rebooted it...
It came up like you bought it.. like a fresh install ...
after all the settigns i tried to flash the new rom again and.... bingo

where can i find the hardspl relocker??

Bricked diamond...

Alright i have a telus HTC diamond (CDMA) and iv unlocked it with cmonex bootloader (The CDMA version on PPCGeeks). I dont know wut i touched but now my phone doesnt boot into windows, it just keeps resetting... When i type rtask c into MTTY (I can still get into the bootloader) it says
Calibration
No Card inserted
HTC_SMEM_CE_RADIO_DBG_FLAG: 300
Enter Radio Image
Iv tried flashing the sprint shipped rom with radio but that did not work...
does any1 have any idea of how to fix this?

CashMoney18 said:
Alright i have a telus HTC diamond (CDMA) and iv unlocked it with cmonex bootloader (The CDMA version on PPCGeeks). I dont know wut i touched but now my phone doesnt boot into windows, it just keeps resetting... When i type rtask c into MTTY (I can still get into the bootloader) it says
Calibration
No Card inserted
HTC_SMEM_CE_RADIO_DBG_FLAG: 300
Enter Radio Image
Iv tried flashing the sprint shipped rom with radio but that did not work...
does any1 have any idea of how to fix this?
Click to expand...
Click to collapse
You MUST install HardSPL before doing anything else........also, try a hard reset......

i do have a hardSPL... i have 0.43.CMONEX on the phone right now and i already tried hard reset many times but it does not work...

CashMoney18 said:
i do have a hardSPL... i have 0.43.CMONEX on the phone right now and i already tried hard reset many times but it does not work...
Click to expand...
Click to collapse
try this one....
http://forum.xda-developers.com/attachment.php?attachmentid=37669&d=1177280888
good luck

that will brick my phone 4ever... i have a CDMA Diamond... thats a GSM hardSPL not a CDMA hardSPL... i have the right hardSPL that is not the problem...

CashMoney18 said:
that will brick my phone 4ever... i have a CDMA Diamond... thats a GSM hardSPL not a CDMA hardSPL... i have the right hardSPL that is not the problem...
Click to expand...
Click to collapse
Sorry about that. my mistake.........

When did that first occur ?
After flashing Hard SPL ?
Anything we need to know about that ?
Could be that NAND is broken. Do a check on bad blocks.
Cya,
Viper BJK

No it was not flashing of the hardSPL... it must have happened when i was trying to figure out how to change the esn... only thing i cud think of that i did wrong was I did the QMAT security unlock with HTC on command which was in the QMAT manual... but i dont think that would brick it like this... would it? also how would i do a bad block check on a diamond... could u list the commands in order? i dont want to mess it up even more...
EDIT: Well apparently i do have bad blocks... what to do now? is that the reason why i cant boot into windows?
It also says my device name is a samsung... which i dont think is right...
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 523 (0x20B) is bad block
BLOCK 869 (0x365) is bad block
BLOCK 1696 (0x6A0) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x800
Partition[2], type=0x25, start=0xE40, total=0xE900
Partition[3], type=0x4, start=0xF740, total=0xC340
CE Total Length(with sector info) = 0x7C1BA00
CE CheckSum Length(without sector info) = 0x7BA0000
Click to expand...
Click to collapse

bump... for viper 2 c

1. Ok ... what command did you use using QMAT ?
2. Did you change any bootmethod or anything else with for example debugtool ?
The bad blocks seem to be not the problem.

the commands i used in QMAT were "rseed" and "rpass" "set 16 0"
i also followed these steps after the brick
1. Get mtty
2. Connect to USB, press enter
3. Type task 32, enter <--Donno what is it for
4. Type 28, enter <--format DOC
5. Flash CE Rom only
6. Hard Reset
but that did not work either...
Also could you give me some examples of commands on changing bootmethod as im not sure if i used any... and i did not touch any debug tools...

CashMoney18 said:
the commands i used in QMAT were "rseed" and "rpass" "set 16 0"
i also followed these steps after the brick
1. Get mtty
2. Connect to USB, press enter
3. Type task 32, enter <--Donno what is it for
4. Type 28, enter <--format DOC
5. Flash CE Rom only
6. Hard Reset
but that did not work either...
Also could you give me some examples of commands on changing bootmethod as im not sure if i used any... and i did not touch any debug tools...
Click to expand...
Click to collapse
ok here's some tips/ideas:
try typing "boot" in mtty or qmat
if this doesn't get the OS booting then you can try "set 14 0"
if that's no good, then to read config flags you can use "readconfig" (as you have MFG spl), all values should come back as 0x0, if not, let us know.
for bootmodes you can check your current bootmode in oemsbl after rtask a. you can try setting it to 0 ("setboot 0" command after typing "rtask a") but i dont think that's the issue.
(note, all the other commands i listed are not for rtask, only setboot is.)

alright i tried all the commands and heres the results
When i type just "boot" the device just keeps reseting
When i type "set 14 0" it comes back with a string of
HTCST ÚÈÒHTCE
and doesnt do anything
"readconfig" all the values are 0x0 like they should be i suppose
and when trying "setboot 0" it gives me an invalid cmd error while in rtask...

HTC_SMEM_CE_RADIO_DBG_FLAG: 300
doesn't seem to be 0x0. You are sure that all items in readconfig are 0x0 ?
Ok ... it seems that the bootmode is incorrectly set.
Try to "setboot 0" after "rtask a".
That will only work if your device is security unlocked

Yes im sure that there all 0x0... unless im looking at the wrong thing but HTC_SMEM_CE_RADIO_DBG_FLAG is not in the readconfig...
Also it tells me that setboot 0 is an invalid command... and im pretty sure im security unlocked (SuperCID and the bootloader says security unlocked at the top)... only thing i can think of is maybe the 0.43.CMONEX bootloader does not have the setboot command...
Cmd>rtask a
Enter Radio Bootloader
POWER ON PMIC VREG_USB : SUCCESS!
ECHO ON MODE
setboot 0
Invalid cmd!...
readCID
@CID: 00000000
Click to expand...
Click to collapse
EDIT: Alright so i just found this new command "checkimage" and it came up with
Cmd>checkimage
SPL CRC checksum = 0x40142266 CE CRC checksum = bad=0x300
bad=0x45A
0xA069868D ExtROM CRC checksum = 0x0
Click to expand...
Click to collapse
which is where i believe the HTC_SMEM_CE_RADIO_DBG_FLAG: 300 is coming from... any ideas?

Ahh ok .... way better.
Yes, setboot is only available on MFG Bootloader.
As you can see, the CE OS CRC failed. So you need to flash CE OS again.
Be sure that you flash a valid ROM. Try an original one from HTC.
Maybe you've got a connection problem whilst uploading. Try to flash again using another PC
If that doesn't work out, it seems your nand flash is broken.
Cya,
Viper BJK

alright so i flashed the original sprint shipped rom again buh that did not fix the checkimage error... so any more ideas on how i may fix this
NAND broken as in theres no way of fixing it ?
Also i got a tip from someone aty ppcgeeks to flash the radio via rtask... would that make a diffrence as opposed to flashing normally through the bootloader and RUU?

Err flashing via rtask is possible ... but it's really user-un-friendly and more risky
I guess they thought about rwfactory command ...
I'll rethink the options in the next days and will come back to you.
Cya,
Viper BJK

Alright so heres another update on my progress or not so progress... lol
I flashed the verizon CDMA radio that was just released (For the HTC TOUCHPRO but works on the diamond as well) and now instead of the phone resetting it just keeps vibrating right after the touch diamond text/Red info screen...

I really guess your NAND is broken ....

[HELP] Days with a bricked Diamond

Day2 with a bricked Diamond....
=================================
Background
==========
Happened while trying to flash EnergyROM released 7/22
WinXP, not on any USB Hub, and on Unsigned-Hard-SPL-Diamond-Olinex.
The vol down + back + reset method doesn't go to completion (I have had no issues with BsB roms so far using this method), on the Diamond it shows :
--------------------------
00018003
DIAMING.nbh - FAIL
OS - FAIL
Update Terminate
UPDATE FAIL
--------------------------
If I try to soft reset the screen shows the classic bootloader screen, and the RUUNBH at the top-right:-
-----------------------
Diam100 64M
SPL-1.40.OliNex
MicroP-Diam (LED) v.11
-----------------------
PSOC-Diam STAGE_PVT v0x30
Upgrade ROM code error
Please try again
--------------------------------------------
I am able to re-flash this HardSPL (and in doing so removes the ROM Upgrade Error and enter into Bootloader mode (vol down + reset) successfully.
I am also able to re-flash my Radio (Diamond_Radio_1.00.25.05.nbh).
Any rom however that I then try to flash using CustomRUU/ROMUpdateUtility does not work, it always gets stuck at around 20% with the below error:
---------------------------------------------------------
ERROR 226 : FLASH WRITE
Flash write error happened. Pls check your PDA phone.
---------------------------------------------------------
I read that I am supposed to be trying signed ROMs that work with my HardSPL, and went to this thread to get one, but same thing it is also stuck at 20%.
http://forum.xda-developers.com/showthread.php?t=400411
Have also tried the below MTTY method describe in some of the Kaiser (Yes, pretty desperate, getting stupid) threads:
======================================================================================
1. Download mtty.exe from here: http://taeguk.co.uk/xda
2. Disable activesync (connection settings -> uncheck "allow usb connections")
3. Kill the following two processesto stop active sync; rapimgr.exe and wcescomm.exe (Ctrl+Shift+Esc, select from the list of processes).
4. Connect your Kaiser to PC using USB cable.
5. Open mtty, select USB port and click OK.
6. Hit ENTER twice, you should see the "Cmd>" prompt.
7. Type the command "boot", you should see something like this:
Cmd> boot
InitDisplay: Display_Chip=1
No card inserted
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
======================================================================================
...except that I don't get the above lines after executing the boot command, instead I see:
--------------------------------------------------
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fill RSVD information for block 288 to 321
Storage start sector=0xFF40, total sector=0xB080
Storage start block=1054, total block=706
Total Bad Block in CE: 1
Erase physical block from 1345 to 2032
si backup: Erase physical block from 2032 to 2048
Fixed new dwPSImageSize = 0x5640000
--------------------------------------------------
...and my Diamond boots to the "Touch Diamond" screen with the black backdrop. Can someone help?

try to connect the phone with mtty and type task 29.
this should format your phone.
then connect it with activesync and flash a stockrom onto it.
it that works, try flashing a design rom.

Dude, thanks for your reply... I got the following, this means it failed right?
------------------------------------
Cmd>task 29
Format BINFS start
Fill RSVD information for block 288 to 321
CE start sector=0x14, total sector of CE and TFAT=0x14
CE start start block=321, total block=1727
ERASE block 226 FAIL !!!
Write 0xFF start page=0x5040, total page=0x1AFC0
Format BINFS end
Cmd>

epiphone said:
Dude, thanks for your reply... I got the following, this means it failed right?
------------------------------------
Cmd>task 29
Format BINFS start
Fill RSVD information for block 288 to 321
CE start sector=0x14, total sector of CE and TFAT=0x14
CE start start block=321, total block=1727
ERASE block 226 FAIL !!!
Write 0xFF start page=0x5040, total page=0x1AFC0
Format BINFS end
Cmd>
Click to expand...
Click to collapse
try flashing a stock rom. you can download it from the htc website and see what happens.

Dude....Tried this stock rom (actually I tried before trying what you suggested), it still didn't work; the flashing process still stuck at the same place 26%.
RUU_Diamond_hTC_Asia_HK_WWE_1.34.831.1_52.24.25.08_0.93.25_Ship

found this in another thread :
type (dont copy&paste):
task 28
and press enter
If the result is the following then you are out of luck:
flFormatPhysicalDrive:status=23
DOC_format failed!

Got this:
Cmd>task 28
Format start
Fill RSVD information for block 288 to 321
Storage start sector=0xFF40, total sector=0xB080
Storage start block=1054, total block=706
Total Bad Block in CE: 1
Erase physical block from 1345 to 2032
si backup: Erase physical block from 2032 to 2048
Format end
Cmd>
Trying stock rom again.....

on my old phone i had to type
format BINFS
to format the flash. you could try that.
if the rom flash still does not work.
you seem to have a bad block on your internal memory. i am not sure how to get around that.
a stock rom fills the entire rom space with new information. that might introduce problems as well.
maybe you should also try a design rom (not the energy one, because that is a large rom)
try the bsb or deepshining. they have less information and might not use the memory at block 26.
if that does not help, you will have to find people with more knowledge than me.

Still can't flash the stockrom still stuck at 26% after trying task 28...
I can't get the format BINFS command through:
Cmd>format BINFS
Command error !!!
Thanks for your time anyway dude... appreciate it.

try searching , i also found this
http://forum.xda-developers.com/showthread.php?t=296722

*deleted repeated post

*deleted repeated post

Dude.. no offence but that I thought is for Hermes, not HTC Diamond? Also that thread seems pretty old...?

Bump... anyone can give other suggestions?

disconnecting any USB device
epiphone said:
Still can't flash the stockrom still stuck at 26% after trying task 28...
I can't get the format BINFS command through:
Cmd>format BINFS
Command error !!!
Thanks for your time anyway dude... appreciate it.
Click to expand...
Click to collapse
try disconnecting any USB device the PC, including Pendrive (leave only the diamond connected), then flash the stock rom

epiphone said:
Dude.. no offence but that I thought is for Hermes, not HTC Diamond? Also that thread seems pretty old...?
Click to expand...
Click to collapse
i am sorry that there is not a solution on a silver platter.
so after reading my link things you could try:
the hardspl is made by the same person. maybe he included the task 2a in your spl as well?
apparently fixing a bad block can be done with a hardspl. maybe you can send the guy creating the hardspl a personal message with your problem.
get your magic wand, wave and say "reparo"
throw your phone out the window or send it for repairs.

Dude, thanks for your answer, nothing helped me still...
I have tried to PM the SPL makers, but quite sure they wouldn't have time to respond Eventually i have had to book my Diamond in for repairs, not sure what is the cost/repair.
My problem now is what should I do in future, since I figure I will flash again... don't see what I done wrong that can suddenly cause this to happen in the first place... I have been flashing for about a year now.

epiphone said:
Dude, thanks for your answer, nothing helped me still...
I have tried to PM the SPL makers, but quite sure they wouldn't have time to respond Eventually i have had to book my Diamond in for repairs, not sure what is the cost/repair.
My problem now is what should I do in future, since I figure I will flash again... don't see what I done wrong that can suddenly cause this to happen in the first place... I have been flashing for about a year now.
Click to expand...
Click to collapse
there is never any garantee for flashing.
things you can try are the same as the things you tried to restore your phone.
so format or flash a stock rom, before a custumized rom.
do not try every rom, but just the ones that seem professional.

i know this is old topic but i want to contribute.
just today had sort of same issue, except my device flashed full until the end where RUU replied error and the device got stuck spl with RUUNBH. i did task 29 and the flashed a stock htc rom and that fixed issue. just like that.

Hello Everyone!
I'm having the same issue as OP, but I tried task 29, task 28 55aa, task 28, and neither worked for me. The flash of a single OS stucks at 76% with flash write error (226), I've searched the forum for hours, but none of the same flash error code issues was mine. I can reflash radio, but not the os, my hardspl is olinex 1.93, when I reflash the radio it start and stucks at the Touch Diamond screen with the radio and stuff number on the right side. If I then try to flash a rom (even stock rom from HTC site!) It freezes around 65% with the same error. If I command in mtty task 16 0, then again it freezes on the Touch Diamond screen. Please anyone can help?
UP: Got it resolved!! My internal flash is damaged, coz if I flash a 60Mb rom, it succeedes, if I flash a rom with over 80mb in size, it fails.

HELP PLEASE!!! Diamond stuck in tri-color screen

i have olinex hard spl 1.40 installed previously and the device was running perfectly until today it just restarted in to tri-color screen???!!!! i Have tried:
1. soft reset
2. hard reset (full nand from hard reset option also)
3. stock rom flash 100% ok
but still the device is in bootloader mode. the stock original rom flashes ok 100% but then the device returns back to bootloader screen when it restarts after rom flash. please guys help me. i dont know what to do..

you will need to stick it in to bootloader mode bu holding the down volume key and the back button and resseting your soft reset your phone this will take you in to bootloader mode and you should be fine from there.

already at that mate
The phone is already on bootloader mode. It just will not kick out of the mode.
I tried flashing the stock rom. but it just end up in bootloader mode after successfully flashing the rom. i tried several times to flash the thing but still the same. HELP me please guys!!!!

xiyan2127 said:
The phone is already on bootloader mode. It just will not kick out of the mode.
I tried flashing the stock rom. but it just end up in bootloader mode after successfully flashing the rom. i tried several times to flash the thing but still the same. HELP me please guys!!!!
Click to expand...
Click to collapse
Try hard resetting the phone. Or using mtty to clear your device.

mtty???
band27 said:
Try hard resetting the phone. Or using mtty to clear your device.
Click to expand...
Click to collapse
I am trying to do just that but i dont seem to know.. could you point me in the right direction please thanks for the awesome support.
http://forum.xda-developers.com/showthread.php?t=540290. i have followed this link but i dont think it is working for me...

bootloader
check that the volume down key is not stuck pressed in

xiyan2127 said:
I am trying to do just that but i dont seem to know.. could you point me in the right direction please thanks for the awesome support.
http://forum.xda-developers.com/showthread.php?t=540290. i have followed this link but i dont think it is working for me...
Click to expand...
Click to collapse
Please give details to any errors as it's difficult to know where you went wrong....

what seems to be the problem???
after following all the steps in the post #4 I follow with the rom flashing after successful rom flash the device reboots to the tri-color screen again.

OK Let's Back up a bit...
1)So your device is a Diamond and it has Hard SPL 1.93, yes?
2)When you plug in your device do u see the USB label at the bottom?
3) do you have a DIAMIMG.nbh file in your internal rom?
4) Have u tried other Roms to Flash?

This is what i get
Cmd>task 29
Format BINFS start
Fill RSVD information for block 288 to 321
CE start sector=0x14, total sector of CE and TFAT=0x14
CE start start block=321, total block=1727
Write 0xFF start page=0x5040, total page=0x1AFC0
Format BINFS end
Cmd>

xiyan2127 said:
Cmd>task 29
Format BINFS start
Fill RSVD information for block 288 to 321
CE start sector=0x14, total sector of CE and TFAT=0x14
CE start start block=321, total block=1727
Write 0xFF start page=0x5040, total page=0x1AFC0
Format BINFS end
Cmd>
Click to expand...
Click to collapse
Perfect....nothing wrong with your output. Now the question is ....did you put your DIAMIMG file in the root of your Internal memory ? If yes, the from mtty write task 8 as instructed by mystic genius. At this point you immediately remove the cable and press (Vol. Down & Back Arrow) and volia. Your device will find the DIAMIMG file in your internal storage and begin the flashing automatically via a grey screen. (press pwr button to begin...etc, etc.) After all that do a hard reset and you are done.

thanks for help
i cant put a rom in the internal memory because this happent out of no where i wasnt going to flash any roms. but i have flashed a rom from my system but after successful flash the device restarts to the tri-color screen again, what is happening

what is this?
Cmd>set 14 0
HTCST ÚÈÒHTCE
Cmd>

this is what i did???
Cmd>set 14 0
HTCST ÚÈÒHTCE
Cmd>task 29
Format BINFS start
Fill RSVD information for block 288 to 321
CE start sector=0x14, total sector of CE and TFAT=0x14
CE start start block=321, total block=1727
Write 0xFF start page=0x5040, total page=0x1AFC0
Format BINFS end
Cmd>task 8
after flashing the stock rom still it restarts into thr bootloader?? why is that.. could anyone explain to me. or show me the direction to how it is done. pls help me....

Hey!!!
I found out that if i input the command boot in the mtty console then my device boots to windows.. why is that???

I have a fully working Diamond but while trying to practice the MTTY process i had found myself stuck at bootloader after reboot, just like you. The reason is unknown to me but as i can always bypass this and continue with usual method, i never try to examine deeply.
By now i use MTTY just to format the memory. Then i close it and keep going with the Custom RUU from PC.
After connecting a device put into bootloader mode into the USB, you should see the "Serial" label changing to "USB" label on the coloured screen. If you launch now the Custom RUU, it should start to flash FROM YOUR PC if there's a nbh under same folder.
If you come to %100 flashed at the end, the device must reset. Then you can disconnect and the device should complete the remaining setup steps.
If you do all above without problem but you are still stuck at bootloader, i can only give 4 explanations (out of possible dozens i can't easily imagine...):
1- The nbh is corrupt or incomplete. Try with another ROM.
2- You're not using an appropriate custom RUU so the flashing looks OK but it's not...
2- You have a flash memory failure in your device, beyond the area which receives the ROM. Maybe in SPL area???
3- Your SPL is the problem. Try to change it to another before reflashing the ROM.
Good luck...

htc diamond
salve ragazzi vorrei parlarvi dell mio problemma con htc diamond,ho provato di agiornarlo, in mezzo si e bloccato io al momento ho tolto la batteria e adesso non si acende piu non va nemmeno in bootloader e non si carica nemmeno non da segni di vita ho provato a schiacare tutti i tasti ma non ne vuole sapere aiutatemmmmiiiiiiii....................hellllllllllllllllllllllllp

Hey...
I Had the same Problem.
The Volume down Key has a Bug...
so sometimes it just presses it by it self.
Some kind of Phantom Bug pressing down the Vol Key.
If you Press the VOL UP KEY during Reseting the Device you may can pass Bootloader. It worked with me.
But the Bug of VOL Down key will also bug you useing it.
I dont know if any one else has this Problem?
But if i take out the Batteries vor a day.... it works a good for a while...
CHEERS

perparim said:
salve ragazzi vorrei parlarvi dell mio problemma con htc diamond,ho provato di agiornarlo, in mezzo si e bloccato io al momento ho tolto la batteria e adesso non si acende piu non va nemmeno in bootloader e non si carica nemmeno non da segni di vita ho provato a schiacare tutti i tasti ma non ne vuole sapere aiutatemmmmiiiiiiii....................hellllllllllllllllllllllllp
Click to expand...
Click to collapse
Intanto write in english, 'cause this is an english forum
Did you flash a ROM or the HSPL?

finally able to get out of the bootloader
Paddyj said:
Hey...
I Had the same Problem.
The Volume down Key has a Bug...
so sometimes it just presses it by it self.
Some kind of Phantom Bug pressing down the Vol Key.
If you Press the VOL UP KEY during Reseting the Device you may can pass Bootloader. It worked with me.
But the Bug of VOL Down key will also bug you useing it.
I dont know if any one else has this Problem?
CHEERS
Click to expand...
Click to collapse
Thanks a lot Paddyj . I also had the same problem and tried pressing volume up key during boot. Voila ! it worked and i was able to get out of the bootloader. Thanks again. I thought that i had bricked my diamond.
Even after booting windows the voulme down key seem to be stuck. i dont know how out of blue this happened to my device. I was working fine uptill now. Any solutions to avert any future problems will be highly appreciated. Thanks

[Q] Rom problem pls help!

Hi!
I have problems with my pda.
Before the refresh, the free ram is about 20% - 30% after a HR, so i can't use it.
First was the hspl, installed from the IS, there was no problem. I see it in the boot screen: spl-1.40.olinex
then my next step was sone_2.5_nomanila installed from IS. It was great!
Then next was sone_v.2.1._nomanila_hun From IS.
Than i think i made a mistake.
I found this radio rom: radio_1.15.25.14.nbh and tryed to refresh the radio
and after the instal the pda wont start...
i see the black background with the touch diamond and nothing happens... after 2 minutes its restart.
i have tryed everything...
downloaded 3 stock roms, and all of them stops at 13% with ERROR [226] : FILE WRITE
i can istall the cooked roms bud the wont start. all of them are the same, stops at boot screen and restart. but costumRUU sad the installation was complete.
I changed the hspl many times, tried with 1.40 olinex, 1.93 and so on....
I cant access the IS.
i tried the task 29 in MTTY, here is the log:
Cmd>set 14 0
HTCST ÚČŇHTCE
Cmd>task 29
Format BINFS start
Fill RSVD information for block 288 to 321
CE start sector=0x14, total sector of CE and TFAT=0x14
CE start start block=321, total block=1727
ERASE block 374 FAIL !!!
ERASE block 681 FAIL !!!
ERASE block 746 FAIL !!!
ERASE block 1430 FAIL !!!
Write 0xFF start page=0x5040, total page=0x1AFC0
Format BINFS end
Cmd>
i am trying to refresh the radio rom but all of them are finish with error.
so i cant install stock rom, because install stops at 13%, i can install cooked rom but it wont start, i cant install radio because all version (from Radio_1.00.25.06 to RADIO_1.15.25.14) terminate with error 226 or error 270
i am tired with this, and i need your help please!
(sry for my english :S)

MohaHGA said:
Hi!
I have problems with my pda.
Before the refresh, the free ram is about 20% - 30% after a HR, so i can't use it.
First was the hspl, installed from the IS, there was no problem. I see it in the boot screen: spl-1.40.olinex
then my next step was sone_2.5_nomanila installed from IS. It was great!
Then next was sone_v.2.1._nomanila_hun From IS.
Than i think i made a mistake.
I found this radio rom: radio_1.15.25.14.nbh and tryed to refresh the radio
and after the instal the pda wont start...
i see the black background with the touch diamond and nothing happens... after 2 minutes its restart.
i have tryed everything...
downloaded 3 stock roms, and all of them stops at 13% with ERROR [226] : FILE WRITE
i can istall the cooked roms bud the wont start. all of them are the same, stops at boot screen and restart. but costumRUU sad the installation was complete.
I changed the hspl many times, tried with 1.40 olinex, 1.93 and so on....
I cant access the IS.
i tried the task 29 in MTTY, here is the log:
Cmd>set 14 0
HTCST ÚČŇHTCE
Cmd>task 29
Format BINFS start
Fill RSVD information for block 288 to 321
CE start sector=0x14, total sector of CE and TFAT=0x14
CE start start block=321, total block=1727
ERASE block 374 FAIL !!!
ERASE block 681 FAIL !!!
ERASE block 746 FAIL !!!
ERASE block 1430 FAIL !!!
Write 0xFF start page=0x5040, total page=0x1AFC0
Format BINFS end
Cmd>
i am trying to refresh the radio rom but all of them are finish with error.
so i cant install stock rom, because install stops at 13%, i can install cooked rom but it wont start, i cant install radio because all version (from Radio_1.00.25.06 to RADIO_1.15.25.14) terminate with error 226 or error 270
i am tired with this, and i need your help please!
(sry for my english :S)
Click to expand...
Click to collapse
There are a couple of mistakes you have done. One for sure is you installed HSPL via IS. Of coz it can be done you have shown. But as to the safety of the process i cant agree to.
Secondly you should have tried jump sspl in the first place. This wudnt have been achieved since you flashed via IS.
Thirdly, i m wondering if you tried mtty after your device failed to start. If its the case,
Owing to the first two, i say your device storage partition is really messed up.
So what we will do at this stage is try to revert to your htc stock rom, which shud have the appropriate memory block addresses to revert ur ROM and Radio.
Let us know abt your device details if you can in ur bootloader mode. And where you bought the device.

Thank you for the help!
I tried to install a lot of stock roms, but of of them stops at 13% with ERROR 226.
Itried mtty too...
I bought second hand.
When i am in the bootloader, i see:
DIAM100 MFG 64M
SPL-1.40.OliNex
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x32
Any idea?

MohaHGA said:
Thank you for the help!
I tried to install a lot of stock roms, but of of them stops at 13% with ERROR 226.
Itried mtty too...
I bought second hand.
When i am in the bootloader, i see:
DIAM100 MFG 64M
SPL-1.40.OliNex
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x32
Any idea?
Click to expand...
Click to collapse
Does your device have a front facing camera and can you do videocall.
I assume you bought from someone who is in the same country as you. So whats ur country bro?

Yes it has a face camera, and i can videocall.
I am in Hungary, and i bought it here.

okay. lemme see if i can come up with a stock rom for you.

can you try to see if you can download the stock rom from this link
http://www.htc.com/europe/SupportDownload.aspx?p_id=133&cat=2&dl_id=483
you will need to scroll down and input ur serial number of the device (which can be found under ur battery)
if u you cant download lemme know

I read this post -> http://forum.xda-developers.com/showthread.php?t=862690
hmm... maybe i tried with wrong stock roms?
i was at htc.com at support but i cant download rom from there because i write my S/N to the box, and they say
"Sorry, this software download is not suitable for your device."

MohaHGA said:
I read this post -> http://forum.xda-developers.com/showthread.php?t=862690
hmm... maybe i tried with wrong stock roms?
i was at htc.com at support but i cant download rom from there because i write my S/N to the box, and they say
"Sorry, this software download is not suitable for your device."
Click to expand...
Click to collapse
since you are located in europe you shud try the link i gave which is htc europe.

I tried your link, and its the same...
Sorry, this software download is not suitable for your device.

can you keep cross checking ur serial number with htc website which is likely for ur area.
else check my pm

sry i dont understand it

hello MohaHGA....jus now i came back...lets see if we can solve ur prob...
give me a few minutes...