Hi,
I updated with success few time ROM usually Duttys 1.7 - 1.8 , i have installed HardSPL 1.4 Olinex yesterday i tried flash Duttys 1.9 its stop on 53 % and show flash error 262 IU 634 after that time i cannot flash any rom the stop on 58 84 % like TOR, PANOSHA, Please help !
Best Regards
Muzzzik77
This is error 262:
Q: During the upgrade, the progress bar is moving. If the error message (ERROR [262] :UPDATE ERROR) appears, what should I do?
A: This may occur when the connection is lost, without power supply, computer host is down, or due to other unexpected cases. You will see that there’s still one progress bar displayed on the device but it is not moving any more. The device cannot get into the Wince screen, so you cannot connect with ActiveSync. This problem usually can be recovered. You just need to follow the instructions in the error message box, reset the device, and run RUU again. RUU will re-flash the whole image again.
Note: You should remove the battery and reset the Mobile Device.
What you can do is reset the device with volume down key pressed. You will enter the bootloader. Check that at the bottom of the screen it says USB and not SERIAL.
If so, unplug the USB cable till it shows USB. Then flash it again. Maybe you should flash a stock HTC ROM first.
Good luck...
Muzzik77 said:
Hi,
I updated with success few time ROM usually Duttys 1.7 - 1.8 , i have installed HardSPL 1.4 Olinex yesterday i tried flash Duttys 1.9 its stop on 53 % and show flash error 262 IU 634 after that time i cannot flash any rom the stop on 58 84 % like TOR, PANOSHA, Please help !
Best Regards
Muzzzik77
Click to expand...
Click to collapse
try to flash an original rom signed like:
RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe
and remove the cover from the back of your device and keep it cooled with something(a vent or something)
is probbably that you have a power management issue on you device
if you got warranty u should take it to the shop with an original rom
i had the same ..
I used Hardspl a few weeks ago.
After 3 retry´s to flash the new WM6.5 HTC ROM,
i installed Hardspl relocker and rebooted it...
It came up like you bought it.. like a fresh install ...
after all the settigns i tried to flash the new rom again and.... bingo
where can i find the hardspl relocker??
Related
I tried the Upgrade, but it did never start, so when I tried to get it back to normal, doing a reset, I only get the Bootloader screen, with the USB and v0.60, I tried a Soft and Hard Reset but nonthing, I have tired to re-flash it again, but also nothing, please any help, thanks
I can not even to start the Flash program, I get ERROR : 101
ERROR 101 : CONNECTION ERROR
PLEASE ANY ADVICE IS WELCOME, THANKS
I WAS ABLE TO REFLASH IT, BUT I STILL GET TO BOOTLOADER ONLY
PLEASE HELP
latest ActiveSync installed? Removed battery?
Had this issue Yesterday. Even if You update the ROM, You will still stay in bootloader (for me it was like this). Do another update, this time only the radio (so delete ms_.nbf and nk.nbf from the directory from where You run your upgrade utility). After this (another 20 minutes) You should be able to have result after the cold-reset.
On the bootloader there is a small difference. Upgrading the ROM shows how far he actually is (in percentage), whilst upgrading Radio it does not show You the percentage, only that he is busy.
Ruud
Just try the update without any insert card (sd and sim), and a wonder will happen!
Teja
- connect the JASJAR with your PC using the USB cable. Activesync will NOT start and the XP says does recognize it
- do a HardReset (press the 2 (-) in the keyboard and softrest it all at the same time. Hardreset screen appears (DON'T press 0 or X..)
- start the update program. Please use a good upgrade like the latest from imate ftp://ftp.clubimate.com/JASJAR_WWE_11353_137_10301.zip
- start the update and when it's looking to check the version of the JASJAR softreset it
It should start to reflash it without problems.
I hope it helps...
Firstly I would like to say thanks to this site and the trinityguides.info site for the great work people have being doing and making available to everybody, it is great being able to use my trinity with wm6, keep the good work going!
Now the issue I seem to be hitting the same "error [260] connection" every time I attempt to update anything on my Trinity. I have followed the advice on the trinityguides site regarding being stuck in bootloader mode to no avail, and I can't seem to find anything in the posts on the xda site which will rectify the issue.
Previously I have been able to update to AX3L v2.8.01 version without any problems, but I decided to update to sammy's ultra light, it initially kicks into des' crashproof sspl, but then it can't connect to the pc. even when I manually enter olipro's hard-spl it does the same. I have tried to re-install hard-spl, but can't. Disconnecting the usb option in the activesync settings doesn't do anything either. Does anybody have any suggestions for me please?
I am not even too sure if my trinity should have both Des' crashproof and hard-spl on it at the same time? Could someone advise me on whether this is alright please?
the tech details:
Trinity
AX3L_OS_v2.0.8.2
radio - 1.46.30 (even though it doesn't say this in the device info, or boot screen after soft reset)
Home PC - XP (just in case)
Did you also try flashing it again, the ROM I mean. I have this error also but as soon as I execute the ROM flash again it finds the device and starts flashing:
http://forum.xda-developers.com/showpost.php?p=1449597&postcount=2
I am assuming you mean flash with the new ROM, sammy's in my case?
yes, as described in the link I posted before. As soon as the error occurs, do not touch the phone, leave it, just start the ROM flash procedure again. (execute ROMUpdateUtility.exe)
No, I am in the same situation. The first attempt puts the device in 'ipl-sspl by des' bootloader mode then after about 10 seconds or so the error[260] is displayed on the pc. If I exit the ruu app and attempt again, nothing new happens on the trinity (i.e. it is still in Des bootloader) and the message is displayed again.
the thing is that when it first goes into des bootloader mode, the white strip doesn't have any text in it. If I pull the usb cable out then put it back in, 'serial' is then displayed in the white bar, but I am still in the same situation as before.
What operating system en activesync are you using?
On the PC I am using XP and Activesync 4.5
Check your connection settings to accept USB connections. Also, try using Hard-SPL 1.30 before flashing the ROM again.
deejacker said:
the thing is that when it first goes into des bootloader mode, the white strip doesn't have any text in it. If I pull the usb cable out then put it back in, 'serial' is then displayed in the white bar, but I am still in the same situation as before.
Click to expand...
Click to collapse
In your PC, try another USB connection.
BLOODY HELL!!! It is the simplest things which we often forget to try. Thanks Jotam for pointing out an obvious point, it must have needed a re-plug of the usb cable into another port for the pc to pick up the device again. I will remember that for future updates so I don't make a dumb ass of myself again. Thanks guys/gals.
Vista
Using Vista? if so which version?
Hi I asked this question yesterday, I am a noob :-[ but the only difference is I'm using Vista Ultimate.
Just for others who have the problem.
When you replug into another USB port (Luckly I've got two on my laptop..)
I used the Vista drivers from TrintyGuides and bingo !
now I try and flash a WM6.....English or Italian...maybe French.
Thanks for the help I keep you posted.
Richard
It works
Now to discover the joys of WM6 after only having WM5 for two weeks....
/i am getting the same only rom update 3.14.4.1 now sees the phone..
has the device name changed???
evene exploit no longer sees the phone
sorry, can you be a little more clear.. what ROM are you flashing, and what exactly is happening?
by the way... i thought error 246 was the connection error... am i mixed up? which is 260?
This seems to be on any rom bar the Dopod roms
and it says 260 connection error
Error 260 connection error - the phone is not going in to bootloader mode - and the RUU cannot seem to initiate communication with the phone.
I'm getting this a lot recently trying to flash.
However, Hold the power and camera buttons while resetting with the stylus (keep them buttons held down).
When you get to the bootloader - plug the phone in - wait till you see the USB at the bottom of the bootloader screen - then run the RUU again - it WILL work - every time.
I used to get this error message alot. sometimes the programs you install don't allow you to update even if you force the phone into bootloader mode so you have to hardreset the device and then upgrade.....hope this helps
htc diamond stuck
T-Rob said:
yes, as described in the link I posted before. As soon as the error occurs, do not touch the phone, leave it, just start the ROM flash procedure again. (execute ROMUpdateUtility.exe)
Click to expand...
Click to collapse
hi ,
my htc diamond stack, no respond on the screen i try to do hard reset with tree buttons but its not working, nothing happaned, screen stay home screen with the time and not responding touching the screen at all
please emergensy help
I had a small problem:
I want to upgrade ROM from 1.35.401.3 to 1.93.401.2...
I download the official .exe from HTC:
Diamond-QMR-RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Dia mond_52.29.25.12_1.00.25.05_Ship
using the S/N from the back of my PDA
... it work till 34%, then it appears UPDATE ERROR:284
"ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode."
What do you recommend to do?
I repeated the process 5 or 6 time, the same stop, at 34% and even recovery is useless
Please help...
there are a couple of things you can try...
1st off, put the phone in bootloader mode (hold "volume down" button and press reset with pen) then flash using a windows XP machine with no running services such as Anti Virus/firewall etc.
if not, try hard SPL developers edition, and then flashing it...
Amz
amzchhabra said:
if not, try hard SPL developers edition, and then flashing it...
Click to expand...
Click to collapse
That would be impossible in bootloader mode using the current toolchain.
The Hard SPL uses a soft SPL that has to be loaded into RAM from within Win CE.
This Soft SPL forces the device to think that it's CID unlocked, and letting the actual Hard SPL flash to the device.
Maybe a hard reset would help:
http://www.hardreset.eu/htc_touch_diamond_hard_reset_soft_reset_en.html
Good luck to you friend.
May be the file u have is corruped, try another ROM!!
Which OS did you use to upgrade from?
Have you tried to use a PC with XP (proffesional) with activesync 4.5 installed?
if all fails:
-kill wcecomm.exe on the PC (with taskmanager) (or disable activesync)
-put Diamond into bootloader..
-Run the official RUU again.
(worked for me on other devices too.. )
All is not lost..
gabib77 said:
I had a small problem:
I want to upgrade ROM from to 1.93.401.2...
I download the official .exe from HTC:
Diamond-QMR-RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Dia mond_52.29.25.12_1.00.25.05_Ship
using the S/N from the back of my PDA
... it work till 34%, then it appears UPDATE ERROR:284
"ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode."
What do you recommend to do?
I repeated the process 5 or 6 time, the same stop, at 34% and even recovery is useless
Please help...
Click to expand...
Click to collapse
Hi gabib77.
As long as you can get the coloured bootloader screen all is not lost, you can still flash your Diamond in the bootloader mode, i.e run the rom update from your PC as normal.
I would first suggest you reflash back to the original rom, try here http://forum.xda-developers.com/showthread.php?t=399680, I am not sure what the "QMR" info you stated on the upgrade rom means, but the second link from the HTC Diamond ROM's List is for the WWE version (1.35.401.3 WWE)
If you cannot flash your Diamond in bootloader mode, then try a hard reset first as mentioned on this thread first.
If you all goes ok then go to http://modmydiamond.info/ for more info on flashing.
Good luck.
I solved the problem... my problem happened because I try to upgrade from 1.35.401.3 to 1.93.401.2...
I put the official 1.37.401.2, then I upgraded to 1.93.401.2 WWE and everything is perfect now...
Thanks everyone for the help
Hello!
I connect my diamond to the pc, with USB cable.
I tried update the original (htc.com) 2.03* Rom install my PDA, but fail.
I tried 1.93, 2.25manila, etc. <--Fail
Each reported error!
Error 226 FLASH WRITE.
Only one allowed to install: sone 2.5 nomanila!
I ran the MTTY (it's show SUCCESSFUL) BUT my IS is intact.
I woud like install Max sense beta, copy IS, bootloader... start install, but than 70% ERROR.
I do not know what's wrong, just let you install the 2.5 nomanila.
I wait your answer! THX
lele09 said:
Hello!
I connect my diamond to the pc, with USB cable.
I tried update the original (htc.com) 2.03* Rom install my PDA, but fail.
I tried 1.93, 2.25manila, etc. <--Fail
Each reported error!
Error 226 FLASH WRITE.
Only one allowed to install: sone 2.5 nomanila!
I ran the MTTY (it's show SUCCESSFUL) BUT my IS is intact.
I woud like install Max sense beta, copy IS, bootloader... start install, but than 70% ERROR.
I do not know what's wrong, just let you install the 2.5 nomanila.
I wait your answer! THX
Click to expand...
Click to collapse
You have not provided much info, because I do not see how it is HSPL, etc!
If you have more info soon be able to help you write!
Hi all,
I wanted to put a new ROM on my Touch Diamond p3700, and managed to bust it.
I followed the MTTY guide from here
http://forum.xda-developers.com/showthread.php?t=416211
I got through the steps OK, but at some point, after restarting the device I noticed that it stop booting.
It would display only TOUCH diamond, and that's it. No other red numbers with RGD.
I tried a hard reset. Nothing. I also did a hard reset with a moviNAN format, and nothing. (though I think this might have made matters worse)
I tried a RUU, and it stays at 0% for a couple of minutes and then gives an error on the PC.
I tried an original ROM, but it says Not allowed for this Vendor ID (goes up to 1%).
I tried Hard SPL 1.24 a couple of times but this also stays at 0% for a couple of minutes and then gives an error.
I am totally out of ideas, but I'm only an extreme beginner, so I do hope there will be a solution.
Any help would be greatly appreciated.
Thanks.
try with HSPL 1.93
hspl 1.93
Hi.
Thanks for the reply
I assume you're talking about this
http://forum.xda-developers.com/showpost.php?p=9246383&postcount=2
I downloaded the archive, extracted it.
As I said, the phone doesn't boot, so I can't connect it to activesync,
but I did go to bootloader (red green blue screen), inserted the cable and showed USB.
Reading your steps I saw that I might have missed the hspl step inside the MTTY tut. So basically I did the mtty part without the hspl.
I connected the phone to the PC, it sais USB, I ran ROMUpdateUtility.exe, the grey screen appeared with 0%, stayed like that for 5 minutes and program gives an error that it can't communicate.
hexer4u said:
Hi.
Thanks for the reply
I assume you're talking about this
http://forum.xda-developers.com/showpost.php?p=9246383&postcount=2
I downloaded the archive, extracted it.
As I said, the phone doesn't boot, so I can't connect it to activesync,
but I did go to bootloader (red green blue screen), inserted the cable and showed USB.
Reading your steps I saw that I might have missed the hspl step inside the MTTY tut. So basically I did the mtty part without the hspl.
I connected the phone to the PC, it sais USB, I ran ROMUpdateUtility.exe, the grey screen appeared with 0%, stayed like that for 5 minutes and program gives an error that it can't communicate.
Click to expand...
Click to collapse
there is no HSPL step to perform in mtty mode. go to bootloader and report back the SPL version you have.
there is no reason you shudnt be unable to format. maybe you might need a jumpSPL if ur previous spl is hard spl-ed
In bootloader is says:
DIAM 100 64M
SPL-1.93.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x32
hexer4u said:
In bootloader is says:
DIAM 100 64M
SPL-1.93.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x32
Click to expand...
Click to collapse
you are still having the stock SPL...
lets get you HSPL...give me a few minutes while i come with attachements and instructions
download+unzip to C:\ (recommended)
- connect ur device in bootloader mode
- dont do mtty at this stage
-run the DiamondCustomRUU.exe
report back
ruu err
I get this
Code:
ERROR[262]: UPDATE ERROR
The ROM Update Utility has encountered communication erros during the update porocess.
The program will guide you step-by-step to recover fomr the errors so you can continue witht the update
hexer4u said:
I get this
Code:
ERROR[262]: UPDATE ERROR
The ROM Update Utility has encountered communication erros during the update porocess.
The program will guide you step-by-step to recover fomr the errors so you can continue witht the update
Click to expand...
Click to collapse
did u try flashing this HSPL?
whats ur current location so i can recommend a flash of stock rom.
I'm in Romania. My phone was locked on Vodafone.
What do you mean "flashing this HSPL"? This error I get when running DiamonCustomRUU.exe in the archive you posted. It starts the progress bar on both PC and phone, stays at 0% and after 5 minutes, it gives that error.
okay. download this. and run the diamond-sspl.bat
if it runs successfully and ur screen turns black...then run DiamondCustomRUU.exe again to flash SPL 1.93
if the batch file does not run let me know...
btw i wil be here till we can sort this out
I connected the device in bootloader. Shows USB.
I ran diamond-sspl.bat
and says:
Warning: no device connected.
Waiting for device to connect...
A window pops up, and says if I want to retry. Hitting yes just pops again.
So basically it says that it can't copy whatever it needs on the device because it's not connected. But the device is connected in bootloader and says USB.
okies....lemme make a cross check of the HSPL on my device and report back
in the meantime, do you have your STOCK ROM? the original rom that came with your device.
if you dont, but still know the rom version to download, check here....
http://shipped-roms.com/index.php?category=windows mobile&model=Diamond
in the event we cant proceed any further, atleast we can recover ur device to start up again with batch file...
Try this version of HSPL which allow a temporary SSPL on ur device in order to allow a transition of SPL..
as usual report back. this is the last step...after this if there is no progress we may have to resort to stock rom and then start at step 1.
btw HSPL 1.93 confirmed working on my device.
The same issue. Error 262.
Isn't the problem somewhere in the communication between the PC and device?
When I run ROMUpdateUtility.exe the device does go to the grey screen with progressbar at 0%, but that's about it.
I don't have my original ROM, and I don't know the version,
but I think this should be it
RUU_Diamond_HTC_WWE_EastEurope_2.03.479.2_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship.exe
You can try restarting your PC and then try to confirm any USB conenction problems.
But if on the device it appears USB in the bottom half of the bootloader screen it means the connection is okay.
Now this is a flash (see attachement) i only use as a last resort. If this doesnt flash, consider downloading the rom file you jus mentioned and flash it...
Download the attachment and run the .exe file. Follow the steps...if it works...try flashing any HSPL u have downloaded.
also try this link from htc.
http://www.htc.com/ro/SupportDownload.aspx?p_id=133&cat=2&dl_id=483
input ur device serial (which is under ur battery) and see if u can download. this is more direct approach to download the correct rom file for ur device.
YES!
Fixed it.
I switched USB ports, left the default driver (2007, not 2004 as was said in MTTY), used the ROM I said above and it worked.
Thanks a lot for your assistance.
good!
and if ur up for another try. then start with the attachement HSPLwSSPL
dont do any mtty. jus try to see if u can flash HSPLwSSPL...
but if ur done for the day, i wish u a rest well earned.... hehe...
anyways feel free to drop a PM in my inbox shud u decide...