Develop Bugs

Trying to Upgrade ( Flash ) and now I am stuck in Bootloader

I tried the Upgrade, but it did never start, so when I tried to get it back to normal, doing a reset, I only get the Bootloader screen, with the USB and v0.60, I tried a Soft and Hard Reset but nonthing, I have tired to re-flash it again, but also nothing, please any help, thanks

I can not even to start the Flash program, I get ERROR : 101
ERROR 101 : CONNECTION ERROR
PLEASE ANY ADVICE IS WELCOME, THANKS

I WAS ABLE TO REFLASH IT, BUT I STILL GET TO BOOTLOADER ONLY
PLEASE HELP

latest ActiveSync installed? Removed battery?

Had this issue Yesterday. Even if You update the ROM, You will still stay in bootloader (for me it was like this). Do another update, this time only the radio (so delete ms_.nbf and nk.nbf from the directory from where You run your upgrade utility). After this (another 20 minutes) You should be able to have result after the cold-reset.
On the bootloader there is a small difference. Upgrading the ROM shows how far he actually is (in percentage), whilst upgrading Radio it does not show You the percentage, only that he is busy.
Ruud

Just try the update without any insert card (sd and sim), and a wonder will happen!
Teja

- connect the JASJAR with your PC using the USB cable. Activesync will NOT start and the XP says does recognize it
- do a HardReset (press the 2 (-) in the keyboard and softrest it all at the same time. Hardreset screen appears (DON'T press 0 or X..)
- start the update program. Please use a good upgrade like the latest from imate ftp://ftp.clubimate.com/JASJAR_WWE_11353_137_10301.zip
- start the update and when it's looking to check the version of the JASJAR softreset it
It should start to reflash it without problems.
I hope it helps...

Brick Hermes, stuck at WM6 Screen, help!

Recently tried upgrading my SPV M3100 from WM5 to black WM6. Everything was going fine and I had installed the following
SPL (Bootloader) version 2.10.Olipro (HardSPL v7)
Radio version 1.43.00.00 (optional)
Was updating to ROM version: Windows Mobile 6 LVSW 160607 when USB cable was disconnected before installation ands I am now left with WM6 screen only
Can anyone help?

If you stuck in the wm6 boot screen and have flashed HardSPL 2.10 already you can just enter the bootloader and reflash your ROM again. Why do you use nearly 6 months old ROM (LVSW)?

Did you try to reflash the ROM?
Just switch to the bootloader and run the update again.
If the updater is complaining about "Not able to do so" you might need another ROM, but that method worked to or three times for me.
Cheers,
Jago

tried raflashing but activesync won't pick up phone

you do not need active sync to pick it up. Just enter the bootloader and run RUU.

how do you reflash without activesync?

Read this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick

richard_g_johnston said:
how do you reflash without activesync?
Click to expand...
Click to collapse
Simply - flashing process itself is not done by the Active sync (its icon is grey when flashing). I have tried to flash a ROM this way and it works. You just have to input correct values to the RUU yourself. Bootloader is the tri color screen. You can access it by holding power and ok button while using the stylus to soft reset the device. Hermes will pick up the usb connection.

Please read the WIKI and flash an original WM6/WM5 rom before attempting to flash a cooked rom.. then make sure you know what you are doing before flashing the cooked.

tried both
http://wiki.xda-developers.com/index...Hermes_Unbrick
http://forum.xda-developers.com/showthread.php?t=286755
still no joy
my device
IPL-1.04
SPL-2.10.0lipro
how do u run RUU in bootloader mode?

richard_g_johnston said:
tried both
http://wiki.xda-developers.com/index...Hermes_Unbrick
http://forum.xda-developers.com/showthread.php?t=286755
still no joy
my device
IPL-1.04
SPL-2.10.0lipro
how do u run RUU in bootloader mode?
Click to expand...
Click to collapse
Put your device into bootloader mode.
Connect it via USB to your PC.
Run the RUU on your PC (like if you had Active sync working).
Flash the ROM.
(should work with all cooked ROMs)
Update: I tried it now with the Schaps 4.20 - it is working.

When you run ruu it should create ROMUpgradeUt.exe if it says it fails to find the device just run this. I usually take a copy before clicking to close the error box.

where do u locate RUU.exe
sorry I'm not an expert in this

RUUWrapper.exe should be in the folder with the image you are flashing. Sorry if I confused you saying ruu.

When you download the cooked rom it comes in rar or zip containing 2 files - one with extension .NBH and the second one is RUUWrapper.exe (resource upgrade unit), unpack them to one folder and run RUU.exe Be sure to flash only ROM for your device otherwise you will kill it for good.

tried running RUU but get error 260, i.e. cannot pick up phone on USB

See post 12

yeah, tried running ROMUpgradeUt.exe, but still no joy

markafreeman said:
See post 12
Click to expand...
Click to collapse
If this does not work for you - then you can use flashing from the SD card (no USB needed for this kind of flashing) . But try what markafreeman suggests first.

Lets try some troubleshooting:
Whne you connect your device in the bootloader (red green blue screen) to your pc what does it say?
In the white part of the screen on your device it should say USB - then it will work.
If not you can still try flashing the ROM from the SD card - you will need a card reader though for this kind of flashing.

WM 6.5 for T-Mobile MDA III

Hello,
if got the T-Mobile MDA III with WM6.0.
Now i want to update my ROM with WM 6.5, bit i only become the following error:
Your image has corrupted. please check your update utility.
Can anyone help me???
i hope you can help me.
thx
markus

try to re-download the rom and make sure you run a USPL first if it's your first upgrade. Search the forum if you need help

it dosn´t works
i´ve tried 5 different roms but no one works.
its the second upgrade on the fon.

Try a new update of SPL, files here= http://forum.xda-developers.com/showthread.php?t=311403
Download "ArtemisUSPL.zip"
1. Unzip
2. Connect your phone to computer, make sure activesync is enabled (green icon)
3. Run start_uspl.exe on your computer and wait until process finishes
4. The phone reboot.
When boot is done, you are CID unlock forever normally so you can flash all rom you want.
Then, You can flash now your rom, just run RUU from your rom folder and normally it's good.
If it always don't work, give us all the number show in your 1st screen when the phone boot (IPL, SPL ...)

yes, tell us what numbers you get on your screen
also what error are you getting
and what OS are you on....vista? XP ? Did you get an activesync connection before you tried flashing?
also try putting phone into bootloader mode first and then flashing, sometimes helps. (hold down RECORD/NOTES button when you reset)
once you've got an error number ( eg error 260 ) you can try searching the forum for that error number and see how everyone else has coped with it.

Cant flash, ERROR 246

First of all, hi, i was reading a lot from this forum, and i must say, im impressed. Nice job!
Anyhoo, im running WM 6.1 (Lite) (http://forum.xda-developers.com/showthread.php?t=364031) on my HTC TyTn.
Now id like to flash it into, i dunno, the full version, or 6.5, or something else, but it wont.
I connect it through active sync(on my desktop pc), and i run 'Force Using Safe SSPL', i get the error : ERROR 246. The Update Utility cannot get response from your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone. And also check your PDA Phone.
Click 'Exit' to quit.
I tried to run SPL-2.02/2.10/2.30 and then it goes into bootloader, and at 1% it says 'file corrupted'.
I tried those things on my laptop, too, but still the same problems.
Can anyone help me?
Rgrds

Install NetFrameworks from v1 to v3.5 make first your device is runing a functional rom.... or your rom... then perform the Hardspl v7 by olipro hardspl 2.10 and then try to upgrade some other... the fact here is.... how could you have 6.1 and now you are trying to make hardspl... oh bTW dont use SSPL please you gonna damage your device if it is not ready damaged.

Do i install NetFrameworks on HTC or on my PC?
Why not use SSPL? Which option should i use?

Do i install NetFrameworks on HTC or on my PC?
Why not use SSPL? Which option should i use?

hi,
when i try to perform the Hardspl v7 by olipro hardspl 2.10 i the following error:
Error 206 update problem
http://img97.imageshack.us/img97/107/48319879.png
please help me

nvr, worked it out.

Try this,
1. Make sure you have HSPL 2.10 or New Bootloader
2. Put Your device into bootloader mode (Until there a "SERIAL" in the bottom of ur device), connect it to PC (Now "SERIAL" change to "USB")
3. Run 838Pro_SEA_ENG_WM6_Upgrade_20070712 (official ROM or U can RUN other official ROM can be found on www.htc.com ), don't click "AUTODETECT",
4. Checklist the option button of SPL-2.02/2.10/2.30 New Bootloader and Is it Hard-SPL?, after that just click next2 until flashing started
5. If it didnt work repeat step 1-3 and checklist the option button " Force Using Safe SSPL " then follow all flashing step
6. Run AT&T Strip, link: http://www.4shared.com/file/61372397/e2bf76c0/official_ATT_WM6_striped.html
7. Flash WM6.5 ROM you want
Hope its usefull cause I use this when my hermes couldnt load and every flashing it's stuck on 1%
Good Luck

ksemeks said:
nvr, worked it out.
Click to expand...
Click to collapse
I'm having similar problems too, Please kindly share how you worked it out.

HardSPL + MTTY, an almost bricked HTC Diamond!

I really need some help!
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and I made a mistake as follows;
blanktruth said:
Ok, first of all I did not think that it was this dangerous to use MTTY!.
I followed everything and came to these lines
---------------------
Cmd>task 8
Cmd>
---------------------
But after Cmd>task 8 my device restarted immediately before the second line Cmd> appears and I panicked and disconnected my device and pushed the wrong buttons while "Touch Diamond" logo was on the screen.
Now, nothing happens. I can not start from the beginning because I can not start the bootloader by pushing Vol Down and the small red reset button...
Is there anything else left for me to try? Or should I throw my HTC to garbage?
Click to expand...
Click to collapse
Now, I do not know how, but I brought my HTC to bootloader mode and now I can see it via MTTY. But I mistakenly formatted the Internal Storage while I was trying to bring my HTC to bootloader.
Is there any way to upload the DIAMIMG.nbh file to Internal Storage? Or should I follow a different way to save my HTC Diamond?

i have the same probnlem!! with my diam300
my bootloader show not Diam300 64m but only 64M on the first position in 3color mode... plz help

Connect the Diamond and run the customruu.exe from your desktop, this should work.

how to connect if i used mtty... its clear everything what i have on device storage and in bootloader canot start stock or developed rom...
if i want start hard spl its say invalid model it....

blanktruth said:
I really need some help!
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and I made a mistake as follows;
Now, I do not know how, but I brought my HTC to bootloader mode and now I can see it via MTTY. But I mistakenly formatted the Internal Storage while I was trying to bring my HTC to bootloader.
Is there any way to upload the DIAMIMG.nbh file to Internal Storage? Or should I follow a different way to save my HTC Diamond?
Click to expand...
Click to collapse
The only thing to do now is to flash back a stock ROM or use a custom ROM with the RUU.

Solved!...
Dom1n8tr1x said:
First of, your device is supposed to soft-reset after the "task 8" command and you should have been holding down the "Volume Down" and "Back Buttons" to begin flashing your new ROM. The whole idea of using MTTY is to format your Main Storage and flash a new ROM. Therefor you should have loaded the ROM that you wanted to flash onto your Internal Storage.
Click to expand...
Click to collapse
Thank you for your reply.
Actually I had uploaded the ROM to my internal storage, but during trying to bring my phone to bootloader mode, I formatted the internal storage...
Anyway, what I did now is, first I opened the USB Connection feature from ActiveSync, and then used CustomRUU.exe to Flash the ROM...
Everything is solved now...
Thank you very much all...

ilijan said:
how to connect if i used mtty... its clear everything what i have on device storage and in bootloader canot start stock or developed rom...
if i want start hard spl its say invalid model it....[/QUOT
bootloader is all you need to revive the phone
connect it to usb in bootloader mode and just install an oficial diamond rom from an windows xp pc.
it's easy
Click to expand...
Click to collapse

plz write here step by step guide how you solved

How it was solved...
ilijan said:
plz write here step by step guide how you solved
Click to expand...
Click to collapse
Actually the most crucial part was to bringing phone to boot loader mode. And I think I managed that by pushing the Volume Down and Back (the arrow pointing left) buttons immediately after restarting my phone. And I had to do this after taking out the battery and putting it back after 5 sec.
When I pushed these buttons at the start up the phone tried to install the ROM from my internal storage, but as I explained I had deleted it by mistake. Therefore it could not find the ROM. I disconnected my phone from my PC and the screen started to say something like Retrying USB connection or waiting for USB connection, something like that.
I restarted my PC in Digitally Signed feature disabled by pressing F8 during start-up. Reconnected my phone to PC (the screen of the phone was still blinking as waiting or retrying usb connection). And voila the phone screen changed to boot loader mode...
The rest was easy. I opened the USB connection feature from ActiveSync and used CustomRUU.exe with a ROM to flash my phone...
That is all...

1. plug phone in to computer in bootloader
2. run customruu or stock from rom update on computer
3. wait for rom to flash to device
4.???
5.profit

but my booloader dont show model ID: DIAM300 64M what i had befor
and show me only: 64M
and any flash error with invalid model id, i canot flash, rom, stock rom, or hardspl...
understand me.. im not totaly noob... i used mtty X times... but now have this probles

can somebody help me?
my diamond dont have model id...
before i had in bootloader mode DIAM300 64M model id, but now i havent got... its show only 64M,
every rom flash stopped at 1% cose model id error,
every hard spl falsh finished 100% but after flash when device restart write model id error...
i cant do anithing... can somebody help me?

For everyone facing problems after flashing his/her device, take a look at the link in my sig.
There you can find a guide to restore your diamond.

you dont understand me..
i canto flash any rom any hard spl becous my diamond dont have device ID...
in bootloader dont show DIAM300 64M but only 64M
after all flash say error mobile ID...
i try mtty, hard reseted, soft... and nothing
after start its show me only first stock screan, the red text on the right bottom sight dont start: 1.17.25.14
2.100000
geny d2x
its maybe wrong but i forgot what waz here...
how can change device model ID? form 64M back to my stock DIAM300 64M?

Try another version of Hard-SPL, some people report that 1.40 not fully works.
I suggest you try 1.94 Olinex.

my diamond is death... if somebody know how can heal it... plz write me...
my device ID is missing... so i cant flash any rom, any hard spl, any radio...

try this? http://forum.xda-developers.com/showthread.php?t=409425&highlight=invalid+model+id

im not sure but i dont think one can brick his/her phone after hard spl, thats the reason of hard spl in the first place that u dont brick it. boot loader is always present

Guide
if you are using Windows XP try the following steps:
Connect your device to your PC
In Active Sync > connection settings > check Allow USB connections (which you have un-checked while doing MTTY)
Find a ROM with CustomRUU.exe / diamond wrapper
Now enter into bootloader mode(forget about the device ID)
Go to customRUU.exe and run it
Follow the ROM installation steps
This will help you installing your new ROM.
I had a similar problem and i resolved it by follwoing the above steps.

Guide
if you are using Windows XP try the following steps:
Connect your device to your PCIn Active Sync > connection settings > check
Allow USB connections (which you have un-checked while doing MTTY)
Find a ROM with CustomRUU.exe / diamond wrapper
Now enter into bootloader mode(forget about the device ID)
Go to customRUU.exe and run it
Follow the ROM installation steps
This will help you installing your new ROM.
I had a similar problem and i resolved it by follwoing the above steps.