I cannot stand the installation procedure needed for the screen protectors. Every single time: I use the "provided micro fiber" cloth to remove dirt and lint and the apply. EVERY TIME I am left with tiny lint,, micro specs of air dust etc. between the film and the screen, and a small little bubble here and there. It drives me crazy. Call me obsessive compulsive but it take me about 3 screen protectors until I finally get it right. Anyone aware of any screen protection technology that will help me avoid this outcome?
I don't, but I did read that if you apply it in the bathroom after running hot water and steaming it up real good that it will help that problem a lot. I plan to try that when I get my first screen protector this week.
Sent from my SAMSUNG-SGH-I897 using XDA App
Hard type screen protectors will solve your bubble issues. Martin Fields screen protectors is pretty much impossible to have bubbles stuck inside it.
However it won't solve your dust problem. If anything, it's much easier to see dirt and other imperfections stuck between the screen and a Martin Field protector.
Or you could try one of the crystal screen protectors from boxwave. I had your problem too with my first 2 screen protectors, and it seemed that I couldn't just get them on there without a problem. With this one from boxwave, I just wiped it off with the provided micro-fiber cloth and used the bubble-elimination card to remove any possible bubbles under the screen!
http://www.boxwave.com/
Get the ones from ATT. I have tried Bodyguardz, Zagg, Stealth Guards, and some generic BS from eBay. All of those were the type you apply with the solution (and have that dreaded orange peel look) and you have to wait for it to "cure" and it is extremely easy to get bubbles stuck in them.
The ones from ATT on the other hand, are completely smooth and truly invisible. They are a stiffer material and you do not need application solution. I am very happy with them and for 9.99 you get 3 of them. If you mess one up by getting some lint on it or whatever, you can just wash it with soapy water and spray it down with some water+baby soap and re apply it that way. Very easy to get the air bubbles out that are caused by using the solution. Again, they can be installed with no solution at all and if done carefully, it should look like nothing was ever installed on the phone
http://www.wireless.att.com/cell-ph...038&q_sku=sku4770252&q_manufacturer=&q_model=
I got them from a local store for 7$ since I got a discount. Those above ^^ from BoxWave seem extremely over priced. For 10$ you can't go wrong with the ones from ATT.
I am using clarivue not even a single dust, lint, inside. It's the quick and easy 3 layer type screen protectors.
Here's a tip ... go to the bathroom and turn on hot water on sink or whatever to create humidity that would trap the dust or w/e in the air ... and it makes this easier to apply.
I haven't had a screen protector on my Vibrant in almost 2 months now & even with constantly putting it in my pocket with my keys, dropping it once onto my driveway & even fumbling it into bouncing off a brick wall one time I have yet to scratch my screen. The rest of the phone is dented & scratched but the screen is still beautiful.
Siks said:
I haven't had a screen protector on my Vibrant in almost 2 months now & even with constantly putting it in my pocket with my keys, dropping it once onto my driveway & even fumbling it into bouncing off a brick wall one time I have yet to scratch my screen. The rest of the phone is dented & scratched but the screen is still beautiful.
Click to expand...
Click to collapse
+1
I had my iPod Touch for years, in and out of pockets with keys and pocket-knives and cell phones, dropped countless times, two little kids messing with it all the time, accidentally sliding it face-down across surfaces, and so on. Never used a screen protector, never got a single blemish or scratch. And that was basically plain old arsenic-free glass. The Captivate is made with Corning's high-tech Gorilla Glass.
Sure, either could still scratch or break. But it's like getting a car with an expensive paintjob, and then covering the whole thing in Scotch tape so it won't get scratched. You end up with something that looks god-awful 100% of the time, because you're afraid something might happen to it that would affect how it looks. Pretty much any time someone hands me their smartphone or DS, it is a scratched, smudgy, dusty mess because of some $40 screen cover they have on there. I always try to point out that it seems odd to make your screen look terrible on purpose just because you're afraid of you might make it look terrible on accident. I used one good one once, that you couldn't even tell was there, but the first time I took it on a flight it turned into smears of rainbows.
use a piece of clear packing tape to remove the dust. running the shower helps bring dust down but there will be some lint from the cloth. dont lean over it, a lot of "dust" is dry dead skin or dandruff so if you have dry skin or dry scalp dust will fall on it. also stop being so anal.
Siks said:
I haven't had a screen protector on my Vibrant in almost 2 months now & even with constantly putting it in my pocket with my keys, dropping it once onto my driveway & even fumbling it into bouncing off a brick wall one time I have yet to scratch my screen. The rest of the phone is dented & scratched but the screen is still beautiful.
Click to expand...
Click to collapse
+1
I don't need no stinkin' screen protector. I mean unless I know my phone is going to be dragged across macadam but then a screen protector won't help, will it.
Gorilla Glass... Screen Protector unnecessary... I have always used a screen protector too on previous phones but the screen on this phone is rugged.
I used to be the same way as you guys, "I don't need a screen protector because it's been through everything and still works perfectly!!" Yet, one day I found a scratch on my screen that I have no idea whatsoever where it came from. So, I got this Boxwave ClearTouch Crystal screen protector, and you literally cannot tell it is on there. It feels just like the glass (con for me actually, I prefer a paper kind of feel) and doesn't scratch easily at all. Plus, I installed it in a dusty room and there was no lint or anything else under the screen. It even comes with a thick card to remove bubbles once it has been applied. So, if you're even slighty, .000001% scared of getting lint trapped underneath the screen, go with Boxwave. I vouch for its clarity and ease of installation. Also, my screen is just as sensitive as before, as I've tried BARELY touching the screen and it still would pick up a touch.
And, in the rare event that you did get dust glued to the screen, it is completely washable and rewashable, so it is a little expensive, but well, well worth it.
Oh, and there is no adhesive whatsoever, not even water is needed. Just peel and go.
magnumrt562 said:
Gorilla Glass... Screen Protector unnecessary... I have always used a screen protector too on previous phones but the screen on this phone is rugged.
Click to expand...
Click to collapse
i listened to this
totally terrible advice. not that i care but i have about 20 microscratches and a couple decent sized ones....
it takes time to learn how to put screen protectors on... I have probably put 500 or so on all different types of phones you just wipe it clean tilt it so that you can make sure there are no dust particles... then you pull the backing off of the protector a few inches apply to the designated area and take a credit card and follow the rest of the protector down... works everytime
iamamp3pimp said:
i listened to this
totally terrible advice. not that i care but i have about 20 microscratches and a couple decent sized ones....
Click to expand...
Click to collapse
I second this . there is no such thing as 'unscratchable glass' some very expensive sunglasses use to have that warranty , guess what , they dont anymore ...
although I have to say the argument about HAVING YOUR PHONE LOOK UGLY JUST IN CASE SOME ACCIDENT CAN HAPPEN TO MAKE UGLY made me laugh , I d never have a phone without one my advice :
Just buy a few cheap ones on eBay and master the trick when your bored , after 3 times it should be installed perfectly , I also noticed if you have light scratches already on it , the screen protector hides them so thats a bonus
Ive tried SO many screen protectors. The only one I have been happy with so far (and VERY happy at that) is Realook. They are SUPER clear, thin, and very hard. You do not lose the glassy feel or the crisp vivid look on the screen. Ive put them on a few phones now, a few Vibrants and a Mytouch Slide 3g (my gf didnt even know i had put it on there till i told her). Its $10 for 2 protectors and I HIGHLY recommend them.
http://cgi.ebay.com.sg/REALOOK-AT-T-Samsung-Captivate-AFP-Screen-Protector-2PK-/250674134359
Siks said:
I haven't had a screen protector on my Vibrant in almost 2 months now & even with constantly putting it in my pocket with my keys, dropping it once onto my driveway & even fumbling it into bouncing off a brick wall one time I have yet to scratch my screen. The rest of the phone is dented & scratched but the screen is still beautiful.
Click to expand...
Click to collapse
I have a tiny little chip right in the middle of my screen on my Captivate about a cm underneath the AT&T logo. It has taken less abuse than yours, and it even has a screen protector on it. It looks like the kind of chip you would get if a piece of gravel hit your windshield a little too hard.
Your mileage may vary.
Hydrocharged said:
I used to be the same way as you guys, "I don't need a screen protector because it's been through everything and still works perfectly!!" Yet, one day I found a scratch on my screen that I have no idea whatsoever where it came from. So, I got this Boxwave ClearTouch Crystal screen protector, and you literally cannot tell it is on there. It feels just like the glass (con for me actually, I prefer a paper kind of feel) and doesn't scratch easily at all. Plus, I installed it in a dusty room and there was no lint or anything else under the screen. It even comes with a thick card to remove bubbles once it has been applied. So, if you're even slighty, .000001% scared of getting lint trapped underneath the screen, go with Boxwave. I vouch for its clarity and ease of installation. Also, my screen is just as sensitive as before, as I've tried BARELY touching the screen and it still would pick up a touch.
And, in the rare event that you did get dust glued to the screen, it is completely washable and rewashable, so it is a little expensive, but well, well worth it.
Oh, and there is no adhesive whatsoever, not even water is needed. Just peel and go.
Click to expand...
Click to collapse
Thanks for the info on the Boxwave screen protector, I've been wandering if it's as good as it looks.
In the malls near me now, there are little carts (you know those areas of the mall, where the cart/carny people are) that have people with small steady hands...
Invisible Shield it is called. They give you a lifetime warranty on the cover. They put it on. They will even cover your entire phone if you want (the back of the Captivate I am thinking of getting covered to avoid scratches on the metal back), and if you get a replacement phone for some reason, you only pay a portion of the price (material only) and they put it on again.
They use some sort of silicon liquid (snake oil... was probably just water) to aid in putting it on, and mine is perfect. Had a couple bubbles with the liquid still in it, but true to their word, it evaporated (through the protector) and it was perfect the next morning.
I jumped at this opportunity after totally FAILING at putting on a protector on my Tilt 2 (two packs of 3). On that phone, I took an exacto knife to cut off the excess I was so bad at it. I gladly paid $20 to have someone else do it and give me a warranty on it.
Invisible Shield. Check out your local mall.
Jeepsdaddy said:
I cannot stand the installation procedure needed for the screen protectors. Every single time: I use the "provided micro fiber" cloth to remove dirt and lint and the apply. EVERY TIME I am left with tiny lint,, micro specs of air dust etc. between the film and the screen, and a small little bubble here and there. It drives me crazy. Call me obsessive compulsive but it take me about 3 screen protectors until I finally get it right. Anyone aware of any screen protection technology that will help me avoid this outcome?
Click to expand...
Click to collapse
I think the gorilla glass is pretty resilient. Check out this youtube vid.
http://www.youtube.com/watch?v=6xASJobjD68
Related
Hello All,
I know that I want a PET or other glass-like screen protector. Generally speaking, I never used screen protectors because they never really held up all that well and on top of that they never had the feel or look of the real thing. Now I have a scratch on my screen that is not normally visible, but I know its there.
I have run into a debacle because I know that while I am good at putting on screen protectors, I am no expert and the PET ones are harder to get perfect than the rubbery ones (which I now despise). So, recently I have seen that there are some PET/Silicone/ Electrostaic Hybrid screen protetctors and then there are still the PET with Adhesive.
Does anyone have experience with the electrostatic type and how good are they at staying on and bubbles?
I have no idea what is PET, or the different types. However, if you are talking about the one I got:
http://www.handhelditems.com/crystal-clear-screen-protector-p-135710.html
my experience is that this has great clarity, can get bubbles during applications, and they rarely come off by itself. On the many devices I've used this type of protector on, only one came off. It started in one corner, and over the course of a month with gradual lint build up the screen protector eventually got ruined. I could've washed it and reapplied for that month, but I had a spare so I was lazy. You can reapply the protectors as needed to get the application right. The bubbles that occur aren't the same as the rubbery kind. Air bubbles can easily be pushed out after application. The problem is dust that prevent the protector from adhering to screen, causing a little bubble. If the dust is really small, the bubble goes away over a day. Or, like me, you can live with it. You try getting something the size of an iPad dust free.
Bought Electrostatic - LOVE THESE!
Ok, as a preface I have owned and used screen protectors before.
I had an iPhone before the EVO and used the Griffin Ultraclear hard Protetctors ad the PowerSupportUSA products of every variety on my previous iPod products (iPod Mini 1G, 4G, Nano 1G, 5G, Shuffle 1G, Touch, iPhone) not to mention an invisible shield one or two. I gave up on the films towards the end of my Touch ownership. They always felt horrible and I could never get one absolutely perfect (didn't help that they usually were not perfectly cut).
For the Evo, I tried the InvisibleShield the first day because I remembered just how well the InvisibileShield had held up on my 5G. Well I think that they have changed the formula, or rather that 3M has since then because the smooth feel and smooth look of the original are most definitely gone. The new variety is rubbery (even after days of use) and is not cut well enough to be a perfect fit (it never covered edge to edge). So i skipped it. Well it seems that with this large of a glass screen, you are much more liable to getting scratches (versus using and unprotetcted iPhone/Touch screen) and I got a few ultra hairline ones that are barely if ever visible to the naked eye and just knowing that they are there bothered me. So I needed to think of getting a screen protector.
Seeing as how air moves and its nearly impossible to get a screen protectors on without any bit of dust, I decided on getting the electrostatic variety so that I could rinse if it came off or needed to be reapplied.
I bought These: Electrostatic Screen Protector - Clear Hard
- Hard variety (PET)
- Very Clear
- Silicone Layer (helps the scratches and dents heal themselves and give sturdiness to the PET)
- Electrostatic layer (holds the screen protector onto the phone)
Six pack delivered for $4? I could do much worse.
Well as it turns out, they are PERFECTLY cut and cover every inch of screen and no more. It went on smooth as butter and I got no bubbles or dust or fingerprints or anything (used a credit card to smooth it down). These were by far the easiest I have had. Not only that, but the electrostatic holds on just as strong as the sticky variety and will not get the gunk on the sides sticking to it! I have taken my TPU case on and off a bunch and had no lift whatsoever. As a bonus, THEY SHOW FINGERPRINTS MUCH LESS THAN THE GLASS SCREEN DOES!
So at $0.65 each, they are killer and having a few backups is nice as well as giving one to a friend.
Cheers!
Thanks for that post. I'm expecting my EVOs (I ordered 2) in within the next week. I've been trying hard to find cases and screen protectors without much luck, but I'm going to go ahead and order those screen protectors you mentioned since you recommend them.
Yep i ordered the same ones and love them. i have loved these from the start. they are quite easy to put on and stay on well.
Scotch tape is your friend in getting screen protectors on without a bit of dust
Childofthehorn said:
Hello All,
I know that I want a PET or other glass-like screen protector. Generally speaking, I never used screen protectors because they never really held up all that well and on top of that they never had the feel or look of the real thing. Now I have a scratch on my screen that is not normally visible, but I know its there.
I have run into a debacle because I know that while I am good at putting on screen protectors, I am no expert and the PET ones are harder to get perfect than the rubbery ones (which I now despise). So, recently I have seen that there are some PET/Silicone/ Electrostaic Hybrid screen protetctors and then there are still the PET with Adhesive.
Does anyone have experience with the electrostatic type and how good are they at staying on and bubbles?
Click to expand...
Click to collapse
I have a steinheil ultra crystal protector on my EVO, and its static. As long as you make sure there is no debris under it, it will stay on for a long time with no lifting. I have shown my phone to quite a few people, and not one of them can tell I have a screen protector on it. Even when I point it out to them, they still cant see it. It's very thin and I applied it perfectly so their a no bubbles. Took me about 30 minutes to get it perfect. If you use a piece of scotch tape to pick up debris under it, that works pretty good. This biggest thing is to make sure your edges are perfectly clean. Even the slightest bit of debris under one of the edges of the screen protector, and it wont be long before it starts peeling. I'm very satisfied with my steinheil. Going on 5 weeks now and it looks flawless. Id take a picture but you wouldnt be able to see it anyways. I thought it was a scam spending $13 on a screen protector! I used to order them from china for 50 cents. well, never doing that again! I've only ever used 1 adhesive type screen protector, and it was terrible. the clarity was awful.
OneStepAhead said:
I have a steinheil ultra crystal protector on my EVO, and its static. As long as you make sure there is no debris under it, it will stay on for a long time with no lifting. I have shown my phone to quite a few people, and not one of them can tell I have a screen protector on it. Even when I point it out to them, they still cant see it. It's very thin and I applied it perfectly so their a no bubbles. Took me about 30 minutes to get it perfect. If you use a piece of scotch tape to pick up debris under it, that works pretty good. This biggest thing is to make sure your edges are perfectly clean. Even the slightest bit of debris under one of the edges of the screen protector, and it wont be long before it starts peeling. I'm very satisfied with my steinheil. Going on 5 weeks now and it looks flawless. Id take a picture but you wouldnt be able to see it anyways. I thought it was a scam spending $13 on a screen protector! I used to order them from china for 50 cents. well, never doing that again! I've only ever used 1 adhesive type screen protector, and it was terrible. the clarity was awful.
Click to expand...
Click to collapse
Have not seen these yet. where did you get yours and do you know if they offer an anti-glare
xlrdxrevengex said:
Have not seen these yet. where did you get yours and do you know if they offer an anti-glare
Click to expand...
Click to collapse
Their anti-fingerprint screen protector is also anti-glare per the product description on their website.
http://www.sgpstore.com/product_info.php/cPath/23_33/products_id/1463
remedy22 said:
Their anti-fingerprint screen protector is also anti-glare per the product description on their website.
http://www.sgpstore.com/product_info.php/cPath/23_33/products_id/1463
Click to expand...
Click to collapse
thanks for the link. Can anyone find this brand cheaper
xlrdxrevengex said:
thanks for the link. Can anyone find this brand cheaper
Click to expand...
Click to collapse
I don't think so.
But these are $13 well spent. Believe me.
~fb
I tried to use them, I really did. The first one was a zagg and it wasn't a very good experience. The screen was rubbery and got scratched up within 2 weeks. So I removed it and just left my seidio case on for a few months. No scratches at all. Now I just got an otterbox impact case and came w/ a nicer screen protector. I put it on, but the lint underneath the screen was driving me crazy. I tried cleaning it off and made it even worst! Is anyone else just rockin it with just a case? I'm done w/ screen protectors.
I used my phone for months without a screen protector until the OB Defender(waste) came out.
I do agree with you that the lint and dust is utterly frustrating. you almost need a clean-room with a surgeon to get the damn thing on right. I can't remember who suggested it, but they said if you take your phone into the bathroom after a good, hot shower, the moisture in the air will keep dust from floating around and you'll get a real clean protector.
i will tell you this, like i said, i rocked my phone for months without any protection. then one day i slid it into the same pocket as my car keys and received a nice long scratch along the length of the phone.
I use the otterbox one and I love it. You really can't tell that there is even a screen protector on the phone. You just gotta be very careful when you put it on. I have gotten really good at it, mine is perfect- not a bubble, spec of dust, scratch, etc...
Screen protectors can be a pain in the ass, but with just a LITTLE bit of time, they can be awesome. First off, i use and swear by steinheil screen protectors. They feel exactly like the glass on the phone and not one person including myself has been able to tell the difference between an evo with it on and no screen protector. Second off, its the method of application that makes or breaks screen protectors. The single best way to apply one is in the bathroom. Turn on the shower and let the bathroom get foggy. This drops all the dusk in the air so you have a nice clean environment to work in. also use a good/new lint free cloth to clean while in the bathroom. use a little patience to get it lined up and start on the bottom and slowly move up using the included tool or a credit card. smooth out any remaining tiny bubbles and your in heaven my friend.
Wish I posted here first before applying the screen protector. I'll just have to baby it for now.
If you are going to use one of the ones made with the military grade polymer, bodyguardz is one of the better ones. It doesn't have the orange peel feel to it and they have a dry apply version.
I use steinheil too. The shower method is a little excessive tho. Just get a couple pieces of tape and dab around the whole screen to remove as much lint as you can, apply the protector and if there is still lint under use a strip of tape to life the protector and another piece to remove the lint.
spankmaster said:
Screen protectors can be a pain in the ass, but with just a LITTLE bit of time, they can be awesome. First off, i use and swear by steinheil screen protectors. They feel exactly like the glass on the phone and not one person including myself has been able to tell the difference between an evo with it on and no screen protector. Second off, its the method of application that makes or breaks screen protectors. The single best way to apply one is in the bathroom. Turn on the shower and let the bathroom get foggy. This drops all the dusk in the air so you have a nice clean environment to work in. also use a good/new lint free cloth to clean while in the bathroom. use a little patience to get it lined up and start on the bottom and slowly move up using the included tool or a credit card. smooth out any remaining tiny bubbles and your in heaven my friend.
Click to expand...
Click to collapse
I started using them and love them. IMO one if not the best out.
You just have to take your time. You cant tell mine is on.. I have used the anti fingerprint anf liked it a lot, but im using clear now and love it.... I wont go to the wet apply again.
Sent from my PC36100 using Tapatalk
I hate the glass. I like the plasticy rubbery feel of zagg. My hand can slide and there's no smudges or prints on. Amaxing
A drop of Chuck Norris's semen was placed on the IPhone. We now have the Htc Evo.
Just FYI, I found a screen protector that I swear buy. It feels like glass, like the original screen. I dont know how scratch resistant it is but after a few months I'm still scratch free. Also I put one on my wifes phone. They come in a three pack off Amazon for $7 and some change shipped. It's worth giving a shot. Here's the link- http://www.amazon.com/gp/product/B003T1WI02/ref=oss_product
mob87 said:
I use steinheil too. The shower method is a little excessive tho. Just get a couple pieces of tape and dab around the whole screen to remove as much lint as you can, apply the protector and if there is still lint under use a strip of tape to life the protector and another piece to remove the lint.
Click to expand...
Click to collapse
That's pretty innovative! I'll remember the tape trick next time. Thanks
I like Zagg InvisibleShield on my EVO. I had to order a replacement since I messed mine up with attempting to put on the front of a DecalGirl skin (pain in the butt).
I know I would have a hard time doing it myself so I had Best Buy install the last one and probably do my replacement. Yeah, they charge $8 but both times on my EVO and on my father's new android upgrade were perfect. No air bubbles, no trapped dust, dirt, and grim under the screen protector.
Check my Signature for a great option for screen protectors. They used to only have one type, now you can get a whole lot of options. I love them! I used the shower method too, and it worked great for me. Still on my first one - 4 months and counting.
jedwardmiller said:
Check my Signature for a great option for screen protectors. They used to only have one type, now you can get a whole lot of options. I love them! I used the shower method too, and it worked great for me. Still on my first one - 4 months and counting.
Click to expand...
Click to collapse
Are there scratches on ur screen protector? That's the other thing that drives me crazy.
I personally have to have a screen protector mainly due to my job . I work in the service department of a heavy equippment dealership . Besides being around dust and dirt and parts being ground down there is no telling what my fingers will pick up . I went with no protector at first and thats when I got my first two scratches . Had the invisible shield installed and scratches got covered up . Point of the story is , depending on your field of work and what you are exposing the phone to pretty much determines how well your screen is gonna remain scratch free . One thing that does irritate me to some extent . I had a Blackberry Storm that remained scratch free and never had a screen protector on it .
spankmaster said:
Screen protectors can be a pain in the ass, but with just a LITTLE bit of time, they can be awesome. First off, i use and swear by steinheil screen protectors. They feel exactly like the glass on the phone and not one person including myself has been able to tell the difference between an evo with it on and no screen protector. Second off, its the method of application that makes or breaks screen protectors. The single best way to apply one is in the bathroom. Turn on the shower and let the bathroom get foggy. This drops all the dusk in the air so you have a nice clean environment to work in. also use a good/new lint free cloth to clean while in the bathroom. use a little patience to get it lined up and start on the bottom and slowly move up using the included tool or a credit card. smooth out any remaining tiny bubbles and your in heaven my friend.
Click to expand...
Click to collapse
Going to give my vote to the Steinheil too. First off, I started out with a Zagg but could not stand the rubbery feel. In addition, I also use my EVO as a music player when I work out (I have an armband case that has a plastic cover on it) and every time I pulled the EVO out of the case after the workout, it would pull the Zagg cover off. PAIN IN THE *SS! I got so tired of it happening, the last time I just crumpled up the Zagg and tossed it in the trash. At that point, I was ready to go with a NAKED screen but had to remind myself that I was on my second EVO. The screen on my first got scratched 3 days after I brought it home (Don't even know how... with a 20-month old running around at home, could have been anything).
Now, going back to the Steinheil - I read reviews of it on Amazon and everyone raved. It was somewhat affordable so I thought, why not. After applying it, I have to say it's pretty awesome. Does it feel like glass? Not in my opinion - it feels "silky" but not SMOOTH like glass (does that make sense?) More importantly, it doesn't feel like rubber like the Zagg. And a fringe benefit, it does a great job of keeping off the fingerprints! And how about working out? I've used put in the armband case now 4X and it hasn't come off once. With the Zagg, I've had to reapply it 4 times!
So, my vote is for the Steinheil too... (BTW, they give you two in a case so you can try and find someone to split the costs with you if cost is an issue).
Boxwave screen protectors are the way to go. The crystal ones are awesome
Sent from my PC36100 using XDA App
I buy the cheap ones from China on ebay and they seem to work fine. I usually just buy them in bulk for like $10 and stash them. I replace them every couple of months once they get scratched. I swear by the shower method in the bathroom, always have a clean application.
I initially had a zagg screen protector but it was GARBAGE. I ripped it off after 2 days of having it. I ended up getting a privacy screen protector off eBay for $3.00 and have had it since. I do miss the crisp clarity of the Evo screen but it has proved useful and has worked much better than that zagg crap.
I got a Zagg as soon as I got my Evo. I had used them on other devices (G1, my brief stint with an iphone, my Moment). Some people don't like the orange peel effect, and say it feels tacky, but it doesn't bother me (I don't even notice the orange peel effect). I have had it since August of last year, since the Evo was so hard to come by for the longest time lol. I have no scratches, and no bubbles. No peeling of the sides, except one when I put my Seidio case on initially, but it smoothed back out. I had Best Buy install it for me this go around, and I couldn't be happier. I have had it like I said, since August, with heavy use, and it stays in my pocket. It still looks as good as the day I got it
I was wondering if there are any go to screen proctectors? Any to avoid, like do any cause issues with the touch screen?
Sent from my Galaxy Tab!
I'd avoid the hard plastic static-type. They're difficult to put on without dust. I've been using the ones from clearprotector (.com). 50% off and free ship with the code iwantultra (have it memorized cause I've gotten several). The corners and edges are kind of a ***** to get on, but they work well and come with a lifetime warranty (or so they say...). This is a wet-application so don't use them unless you're willing to take the time to watch the youtube videos to learn how to install, and then takes about 20 minutes to install.
I get mine from www.bestskinsever.com. I've had no problems with them. The screen protector is easy to apply and very durable.
I have Ghost Armor on mine and like it, it is a bit smoother than Zagg or Bestskinsever.
Be warned if you want the full body protection, adding this to the back of my tab caused me to have the newton ring problem. I never had the problem with just the screen protector on, I should I have just stuck with the screen and not the entire thing but I really wanted the matte back on my tab.
Thanks fellas. I have and used to do/use the wet application ones for a while. Then I got tired of them and just went with the cling ones. I think I'll get the wet app and it should last a longgg time. Especially since Im not going to be using the tab every day.
I went with Clarivue on the recommendation of a friend.
It's decent enough, no tackiness or anything like that but it's not the best fitting, could've been a couple of mm wider and taller.
Other than that, whilst I've had a long-standing dislike for them, recently I've found Zagg's InvisibleShield protectors to be pretty decent - they seem to be very well fitted and the tacky feel to them that I remember doesn't seem as noticeable.
Kinda wish I'd gone with them for my Tab
Which would you guys say offers the smoothest screen experiences of all? I don't care about longevity as I only use my tab about once every 2 weeks
Imo the smoothest would be the cling on ones.
Sent from my Galaxy Tab!
I purchased these in July from Amazon. http://www.amazon.com/gp/product/B0058NXPLK
I was never a fan of the "wet" applications, to me it just seemed like too much work and I was never comfortable spraying any type of liquid all over my devices, regardless of how harmless they might be.
But anyway, this is a clear, non-matte protector that is the "static cling" kind of application. Once it goes on properly, you cannot see that is even there. The touch feeling is the same as if you had no protector on. I really feel that those matte ones, while they do reduce sun-glare, a lot of them provide a "tacky" feeling that maybe is fine for a smaller screen such as a phone, but can become very annoying for a larger screen if you do a lot of swiping across the larger surface area of a tablet. But that is a personal thing....I usually don't use my tablet outside in the bright sun anyway, so the matte types are useless for me.
I've had it on since the end of July and it's held up very well. You do have to wipe the smudges off the screen occasionally, but you'd have to do that anyway even with no protector. I'm extremely satisfied with these.
So I've got an Invisible Shield en route for my Tab, will post back when it arrives.
Same here haha.
Sent from my Galaxy Tab!
I just bought the glare-reduction screen protector from BodyGuardz. Has anyone else had any experience with them? I wanted something that would offer a decent amount of protection for the screen (fingerprint and physical pressure), but also not reduce the touch sensitivity at all. (I type with the tip of my nose since I can't use my fingers, and trying to press too hard hurts )
Not sure where you can get it, but here in Singapore there's a brand called DataFlex and their screen protectors seem really good.
I bought SGP steinheil shield ultra optics. I liked it.
Raistlin1 said:
I have Ghost Armor on mine and like it, it is a bit smoother than Zagg or Bestskinsever.
Be warned if you want the full body protection, adding this to the back of my tab caused me to have the newton ring problem. I never had the problem with just the screen protector on, I should I have just stuck with the screen and not the entire thing but I really wanted the matte back on my tab.
Click to expand...
Click to collapse
So this newton ring issue is a major problem. What if I just protect the back and leave the screen open? I have the new logitech keyboard case on the way and the front is protected in the case, but the back is exposed. I planned on protecting the back only. But I wont do anything if it'll case the newton rings.
Newton Ring?
nuprotocol said:
So this newton ring issue is a major problem. What if I just protect the back and leave the screen open? I have the new logitech keyboard case on the way and the front is protected in the case, but the back is exposed. I planned on protecting the back only. But I wont do anything if it'll case the newton rings.
Click to expand...
Click to collapse
Yeah. Same here. Just want a more "grippy" back. How does one produce Newton Rings from the back of the device. Methunked it was a display issue resulting from the interaction of the protector and display glass...kinda by definition...
Hopefully we'll find out soon. I just want to protect the back.
skeeter123 said:
Yeah. Same here. Just want a more "grippy" back. How does one produce Newton Rings from the back of the device. Methunked it was a display issue resulting from the interaction of the protector and display glass...kinda by definition...
Click to expand...
Click to collapse
I blame the install of the rear skin because I had the screen skin installed first and then three weeks later I had the rear done. He turned the tab face down and installed the skin. When he turned it over, bam, Netwon Rings...
I never had them before the front screen protector, during the front screen protector install or after the front protector was on the Tab.
Will it happen to you? I have no idea but from what I have read about the problem it is caused because of the Tab moving/flexing which can be caused by excessive heat and certain handling of the Tab.
thanks!
Raistlin1 said:
I blame the install of the rear skin because I had the screen skin installed first and then three weeks later I had the rear done. He turned the tab face down and installed the skin. When he turned it over, bam, Netwon Rings...
I never had them before the front screen protector, during the front screen protector install or after the front protector was on the Tab.
Will it happen to you? I have no idea but from what I have read about the problem it is caused because of the Tab moving/flexing which can be caused by excessive heat and certain handling of the Tab.
Click to expand...
Click to collapse
Thanks for taking the time to explain the details. Sounds like a warranty kinda thing mebbe. Hope it gets resolved! Mine is on order and I'll watch out for this issue.
Cheers!
slack04 said:
I'd avoid the hard plastic static-type.
Click to expand...
Click to collapse
I bought an anti-glare protector from Cellularbuy on eBay and managed to get it on in one go with no dust at all. The protector fits perfectly and the camera and light sensor holes line up spot on. The anti-glare makes the screen look a little grainy, but I hear that even the Steinhell ones that are many times more expensive have the same problem.
This has been gone over millions of times on each forum here, but here's how I did it:
-Wipe the screen down with a soft cloth and glasses cleaner or isopropyl to get any grease off
-Run the shower in a small bathroom on hot until the room is unbearably steamy
-Put on a hat to keep your hair and head funk from falling on the screen
-Line the protector up on the screen before removing the film and tape it on one side with a few pieces of Scotch tape
-Also make a "handle" out of tape to put on the top of the protector opposite the taped-down end. This will help with alignment
-Go into the bathroom and clean the screen with a good microfiber cloth. Also clean the front and back protective sheets on the film so there's no dust to come off when you start peeling them. The steam should be enough to wet it. Take one final look
-Peel the protector back and lay it down pulling the taped edge taut to keep it lined up
-Smooth any bubbles out with a credit card BEFORE peeling the top sheet off
IF you do have any dust, use a piece of tape on a corner to lift up the protector and another piece of tape to pick up the dust. If the room is steamy enough and you did a good job of wiping the screen this shouldn't happen.
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
I use painters tape after I clean the screen (before applying of course) to make sure no other dust or hairs are on the screen. Use a can of air to blow away crap in your work area also.
Sent from my Galaxy Nexus using xda premium
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Kobe_No_Means_No said:
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Click to expand...
Click to collapse
Will this work with SGP Ultra Crystal screen protector? or are they only the non-water applyable?
Can't speak specifically for the sgp but I've been using the wet application method on all my dry application protectors for some time across at least 5 different phone models with no issues. Much easier to apply accurately than dry
Sent from my SGH-T889 using Tapatalk 2
degeneration said:
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
Click to expand...
Click to collapse
I read some where that you should apply it in a bathroom and before you start get a spray bottle and put water in it. A couple sprays in the air before... No dust works for me
Sent from my SGH-T889 using XDA Premium
Well I just got 2 more cheap protectors in the mail, the first one I tried to get perfect, and each time I tried to get rid of a piece of dust it would get worse. The second one I have one bubble and I gave up. Fine. I have a bubble... oh, and they are cheapo reflectors, and supposed to be matte... so now my screen looks pretty horrible. Sigh. Whatever, my screen is protected. I will get an SGP later and figure something out in the mean time... maybe take them to a tmo store since they did it for me last time and it came out perfect somehow. I think my house is just too dusty, and there's no way to change that. I live in the desert, I have cats, the place is old. Sigh.
omg just did both of the note 2's and it took about 30-40 minutes, ridiculous, but afterwards looks nice till today i had the damn T-Mobile protector on it lol i got tired of seeing T-Mobile =P
Here's the trick for me. I got in the bathroom turn on the shower for a good few minutes. (Hot water) because the humidity in the air will get rid of most of the dust. Then you apply your screen protector by 1st.
Positioning it first without taking off the adhesive side (to know where the edges should be)
2nd.
You must not use a credit card to squegee out bubbles that'll scratch the screen, if you are put a microfiber cloth over the credit card so you'll be pushing down with the cloth not the card
Sent From the Van Down by the River
phreshjoker said:
Here's the trick for me. I got in the bathroom turn on the shower for a good few minutes. (Hot water) because the humidity in the air will get rid of most of the dust. Then you apply your screen protector by 1st.
Positioning it first without taking off the adhesive side (to know where the edges should be)
2nd.
You must not use a credit card to squegee out bubbles that'll scratch the screen, if you are put a microfiber cloth over the credit card so you'll be pushing down with the cloth not the card
Sent From the Van Down by the River
Click to expand...
Click to collapse
Well i did it at my dining table and i regretted doing so because I ended up getting a few particles underneath, but all you need to do at that point is take any type of sticker (mine came with 2 stickers which were called Dust Removal stickers, but its truly a regular sticker lol) so I had to use that several times, but the final result is great
I ended up ordering the SGP Ultra Crystal and also ordered MobC from amazon (http://www.amazon.com/gp/product/B009M7TZYO/ref=oh_details_o00_s00_i00) which ended up coming in first, so I am still waiting for the SGP but honestly i do regret ordering them because the MobC are freakin great, crystal clear, and i have no regrets of putting it on!
Kobe_No_Means_No said:
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Click to expand...
Click to collapse
degeneration said:
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
Click to expand...
Click to collapse
For with app screen protectors...exactly as Kobe mentioned. Couple of drops / 1 part dish washing liquid to 5 parts water (distilled water if your tap water has too much minerals)...just so the solution is slippery enough for the application process. Run your finger nail down the edge of the credit card / tool your going to use to ensure there are no nicks / sharp edges that will damage / crease your wet app screen protector.
Steamed bathroom also helps.
I recommend dry applications for flat surface...wet applications for curved surfaces.
With dry app screen protectors, those clear / ultra clear packs off of eBay usually work well. The only issues I have seen is that the adhesive may get weak over time (if you need to lift protector to remove dust then press down again) and initial cutouts maybe hard to see from pics. Eventually these dry app screen protectors fall to 3/5/? packs per <$1 ???
Position the dry app screen protector then apply / remove film. There will probably be dust, pet hair, etc. Lift up one corner / side / section at a time and slide the shipping tape between the screen protector and screen (sticky side of shipping tape against sticky side of screen protector)...then press dry screen protector down on the shipping tape which will also press against the screen. Carefully lift the corner / section of the screen protector...then flip the shipping tape over and slide back under between the screen protector and screen (sticky side of shipping tape now facing screen) if needed. Usually the particle is on the sticky screen protector side, but sometimes it maybe stuck to the screen side. The idea is to use a shipping tape with strong enough adhesive to remove the particle without ripping off / damaging the screen protector adhesive. Painting tape adhesive maybe too weak in removing any dust / pet hairs...UPS grade shipping tape maybe too strong...I like Staples equivalent shipping / packing tape...it has just enough adhesive strength to remove any dust / pet hairs.
Hope some of this helps.
What works for me:
http://forum.xda-developers.com/showthread.php?t=1988725
Got my spigen... I am probably never buying from anyone else. Well, I dunno, but from the packaging to the application I felt like I was using quality. I thought I had ordered the ultra crystal but I actually went for ultra oleophobic for some reason... and I am crossing my fingers that the surface tension changes after some use (doubt it) but it does do what it says, finger prints do not stick. However the down side is the s pen doesn't feel nice against it (it did feel really nice against the crappy matte protector, felt like a pencil on paper, but I couldn't stand the rainbow effect, maybe I will try a spigen matte in the future). Any way, I used the "hinge" technique I saw somewhere online and it worked pretty well. Got 3 pieces of dust under the screen (1 on the screen, 2 on the bezel) and I used some scotch tape to life the protector and one of the included dust removal stickers to quickly take care of the problems.
the protector is FREAKING INVISIBLE! right now the screen is off and I can see reflections, and I can barely make out where the protector ends.
Thanks for everyone who gave me their tips and tricks, I finally have a screen protector on my note that I am happy with.
Also, for those people going naked, it doesn't affect my screen but I saw I already have 2 minute scratches on my screen. I keep my phone in my pocket on its own, and somehow I managed to scratch the screen already (got on release day). I have wasted a bunch of cash getting a screen protector on that I was happy with, and I might spend more in the future, but at least I know that if anything terrible happens I can replace the little piece of plastic instead of forever having to deal with a scratch.
EDIT: playing around with it some and then wiping it off, I already am fine with how the S pen feels. I think it was actually sticking to whatever they used to apply the outer layer of protection that you remove after applying the protector. A little bit more drag then on the naked glass, but I like that I can now get more of a tactile response of my writing. I am hooked on Spigen.
I do all my screen protectors at the dinning room table in about 2 mins with perfect results every time. I attached a few screenies but they really don't do it justice. It is insanely hard to get a good picture of something clear when using a flash. the specks of dust that are noticable are on top of the protector not underneath. I'm using the spigen oleophobic and love them.
I just thought I should share a valuable lesson: DON'T BUY CHEAP SCREEN PROTECTORS!
I have been fine in the past with cheap screen protectors from eBay. They got the job done, and they were only a dollar or two. And you got six of them.
Anticipating the arrival of my N5, I bought a Spigen Neo-Hybrid case (Which is excellent), and some cheap screen protectors for $2. (12 to be exact)
http://www.ebay.com/itm/231089059032?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
I bought a bunch because that gives ample headroom if you mess up a few times.
I try to install the first one, and it ends up with bubbles near the cutouts for the speaker and camera. Okay, I'll just try another one.
I've gone through six of them, and they all have the same bubble problem near the cutouts.
I ended up buying higher-end screen protectors: http://www.amazon.com/gp/product/B00EV97UD6/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
I'll be sure to report on those when they arrive.
But the lesson is to be cautious with cheap screen protectors.
The xtremeguard screen protectors are really good, and they can be found for under $2.
mprasolov said:
I just thought I should share a valuable lesson: DON'T BUY CHEAP SCREEN PROTECTORS!
I have been fine in the past with cheap screen protectors from eBay. They got the job done, and they were only a dollar or two. And you got six of them.
Anticipating the arrival of my N5, I bought a Spigen Neo-Hybrid case (Which is excellent), and some cheap screen protectors for $2. (12 to be exact)
http://www.ebay.com/itm/231089059032?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
I bought a bunch because that gives ample headroom if you mess up a few times.
I try to install the first one, and it ends up with bubbles near the cutouts for the speaker and camera. Okay, I'll just try another one.
I've gone through six of them, and they all have the same bubble problem near the cutouts.
I ended up buying higher-end screen protectors: http://www.amazon.com/gp/product/B00EV97UD6/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
I'll be sure to report on those when they arrive.
But the lesson is to be cautious with cheap screen protectors.
Click to expand...
Click to collapse
I've got some of the iSmooth protectors and they are quite good...once I properly installed them. Dry apply are a little tricky but there are enough tutorials and videos to help. I also have the Neo Hybrid and I'm quite happy with it.
BigOkie said:
I've got some of the iSmooth protectors and they are quite good...once I properly installed them. Dry apply are a little tricky but there are enough tutorials and videos to help. I also have the Neo Hybrid and I'm quite happy with it.
Click to expand...
Click to collapse
I guess I lucked out with my choice of screen protector!
Not necessarily. I bought these SAMAR crystal clear screen protectors, managed to apply one without getting any dust or air bubbles. It has all the cutouts, the fit is good, and it is quite smooth when swiping, very happy with it so far. To top it all off it is dirt cheap and you get 6 protectors all with cleaning cloths! I've read others on here who have been happy with this brand too. Would definitely recommend.
use a drop of water when u install. it'll help take out bubbles.
also you can reapply these, just rinse in soap water then water, then shake off excess and apply. squeegee out the water - should be next to nothing.
ktamondo said:
The xtremeguard screen protectors are really good, and they can be found for under $2.
Click to expand...
Click to collapse
True. And even with that. I got one first and tested before I got backups.
I use an IQshield screen protector and it's nothing short of pure awesome. No bubbles at all, and it's so smooth and dried hard. It feels like glass.
You get what you pay for. I bought the spiegen Crystal for 10 bucks and they went on perfect and looked perfect and felt pretty good to you cant even tell its on unless you look at the earpiece closely. But there's always better! I just recently bought a Nillkin Glass screen protector with 9h hardness and olephobic with rounded edges and its gonna be getting here in a week or so and that should be way better than a cheap or high quality screen protector!
This sounds silly, but whenever I install a cheap screen protector, I do two things: first, i make sure the side that's going to be applied to the screen is FACE DOWN. Never face it up, under any circumstances. if I do, its before removing from packaging. I even remove the adhesive that protects the protector itself, with the screen protector face down. this doesn't give a chance for dust to sit on the bottom of the screen when facing up. Yes im sure any dust flying around will still find a way to stick, but this reduces the chances. Plus, you make sure you are applying in a clean environment anyway. I usually vaccum the house (or area at least) prior to applying, and give the dust time to settle afterwards.
second, and heres the silly part: I make sure the screen is completely wiped, and blow on the screen itself with DRY LIPS as im applying the screen protector face down. This blows off any dust that may settle between the time you apply the screen, and make sure lips are dry as to not blow moisture onto the screen.
There really isn't any fool proof method for applying screen protectors without dust, but without some sort of clean box with a built in HEPA filtration system, this seems to work well for me 80-90% of the time, versus just applying like normal.
unvaluablespace said:
This sounds silly, but whenever I install a cheap screen protector, I do two things: first, i make sure the side that's going to be applied to the screen is FACE DOWN. Never face it up, under any circumstances. if I do, its before removing from packaging. I even remove the adhesive that protects the protector itself, with the screen protector face down. this doesn't give a chance for dust to sit on the bottom of the screen when facing up. Yes im sure any dust flying around will still find a way to stick, but this reduces the chances. Plus, you make sure you are applying in a clean environment anyway. I usually vaccum the house (or area at least) prior to applying, and give the dust time to settle afterwards.
.
Click to expand...
Click to collapse
You can skip all the surgical-precision vacuuming if you do the application in the bathroom. Turn on the shower, hot as it'll go. Leave it run for 5-10 minutes til the bathroom is steamy. That knocks all the dust out of the air.
Then you can apply your screen protector in peace.
Caelrie said:
You can skip all the surgical-precision vacuuming if you do the application in the bathroom. Turn on the shower, hot as it'll go. Leave it run for 5-10 minutes til the bathroom is steamy. That knocks all the dust out of the air.
Then you can apply your screen protector in peace.
Click to expand...
Click to collapse
but wouldn't that cause moisture in the air? I could see that getting in between the screen during application. I bought a ton of screen protectors like OP though, so I'll have to give this idea a shot lol
The moisture will get out over time. Its just like having windows tinted
Sent from my Nexus 5 using Tapatalk
unvaluablespace said:
but wouldn't that cause moisture in the air? I could see that getting in between the screen during application. I bought a ton of screen protectors like OP though, so I'll have to give this idea a shot lol
Click to expand...
Click to collapse
It doesn't matter. Even dry-applied screen protectors go on better this way, and any moisture completely dries out quickly anyway.
Spend a few hundred dollars on a phone and then buy the cheapest cases and screen protectors you can? Doesn't make sense.
I'll pay the extra $8 for a Spigen screen protector and a quality case that match the quality of my Nexus.
Sent from my Nexus 5 using Tapatalk
Spigen could've tried a bit harder and made all the cutouts. Even the temporary screen protector that comes with the phone has those. I think most screen protectors will be similar at the $1+ range but you can't expect much from ones that cost $0.25.
xtremeguards didn't have bubbles for me. Buying 6 of the same screen protectors and then saying all of them have problems doesn't make sense.
I'm assuming the OP means the bubbles are from the edge of the cutouts not sticking down which is a common issue with cheap screen protectors.
the cutouts are not made well so the screen protector itself is warped at the cutouts for the speakers etc so its not flat and does not stick down creating bubbles there.
Just install in steamy bathroom. The steam prevents dust from floating in the air.
Sent from my Nexus 7 using XDA Premium HD app
I got this Nillkin one: http://dx.com/p/277084. I only had one. Applied by using the "hinge" method. Went perfectly. Cutouts are perfect and bubbles are removed very easy (easier than other screen protectors I've had).
I used a little wet cloth to make my screen wet and to remove dust. At first it feels very rubbery, but after using it for a day or even less, it feels just like the glass!