Develop Bugs

I'm in bootloader screen beacause the notebook power off

Hi,
I've tried to upgrading with 9000_WWE_20202_20307_11500.exe found in this forum, but the notebook power off (bad economic mode also with the AC plugged) at the ExtRam update on 1%, just after the Radio.
But when I tried to re-run the program nothing change, just the bootloader v1.01.
Now the program recognize that there are nothing installed and ask to install all new Roms but after the second screen the utility tell me everytime: "ERROR 114 RADIO ROM UPDATE ERROR"
Somebody can help me?

Since the OS ROM is updated in the last step(to be precise, Step 3), you can easily take your device out of this bootloader mode.
1)open MS activesync on your desktop
2)go to connection settings and disable 'incoming USB connections"
3)run the exe(see the attachment)
your device should be out of bootloader mode.
PS: you can re-run the ROM upgrade again after your device gets back to life

Now my Universal is completly OFF
Hi, thanks a lot for your attention, I trye to follow your instructions but now after the Exit of bootloader, I can't update my Universal.
After read dozens of messages... I try to explain better my situation:
1) the first update was blocked by the power off in my notebook in the beginning on the ExtendedRam (1%)
2) after this I tryed to re-run the update program and this recognize NO ROM on my UNiversal and asking for replace with all new ROM, but a "error 114: Radio Rom update" don't let make the update. (that repeated many time and every time I tryed to reset, cold reset, warm reset... following all the messages that explained many different way to de-block the situation)
3) Now the screen is absolutly black and the PC say me taht the "USB Device Not Recognized"
Can you help-me?
Thanks for all...

I've search and now I've found the way
Thanks for your help, I have come back at bootloader mode and I can put in the wm6 version !
Bye

hi,
I've trie to update my qtek and during the update I've got an error.
And now I'm blocked on the boot loader mode...
I've tried the joined program, I disabled the USB connection,
and the program can't connect to USB...
I don't what can I do.
please help me...

seranares said:
hi,
I've trie to update my qtek and during the update I've got an error.
And now I'm blocked on the boot loader mode...
I've tried the joined program, I disabled the USB connection,
and the program can't connect to USB...
I don't what can I do.
please help me...
Click to expand...
Click to collapse
It's ok, after a reboot of my pda & PC, I can exit the bootloader.
Thks for this program

Frozzen on boot up. In WM6 but cant do anything

I was upgrading my Hermes 8525 with the latest black pro when my computer turned off. The Hermes boots into windows but displays a black back ground. There is no screen interaction and no buttons work. It does not active sync either or I would have reinstalled.
Is there a way to re-install a rom with out being in active sync mode ?
Also windows recognizes a USB devices but it does not recognize it as a Hermes any more
I need some advice and help
thank you,
Brian

tried to reenter the bootloader and reflash ?
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader

Also check out the WIKI site for upgrade problems HERE.
I've also found that have Hard SPL keeps a lot of problems at bay. You can get that HERE

is it bricked ?

i tried to do a beasty wm6 rom update, everything went well, and at the end of the procedure, it ask me to "press 0 to restaure factory setting" for rebooting, i press 0 and then....nothing. Impossible to start the htc, i can only access bootloader mode, but ain't no more recognize by the pc, i tried to plug it to AC power as i thought of a battery prob, and still nothing, no start, and no led telling me that it's recharging...
i ve done some search on the forum, but can't see something similar to this.
anyhelp welcome
regards

Hi,
did you try to downgrade it to WM5? I also had problems with WM6 and after a downgrade to WM5 it worked again.
Cheers
Michael

sorry wrong thread.

well now when i connect it to my pc it says unknown device, so i dunno how to reflash to wm5
im on vista 64, and when i try to install the 64 driver it gave me on error about a corrupted driver...

Hi
I have the same problem,cannot recognize the usb port.
Anyone has an idea??

try changing your cable and if possible try using a xp machine. i have heard of people having problems when flashing with vista (i did it and no problems)
If after you change the cable, and use a differente computer the universal when you put it in bootloader mode and the word SERIAL does not change to USB i would say its pretty much bricked but if you only flashed your device i would say it is still possible to bring it back from death.
try changing your cable (specially if its the one you usually use) im almost sure thats your problem.
also make sure you dont have the sd card or the sim in it that seems to help too.
best regards and best of luck
Erik

luxeomni said:
im on vista 64,
Click to expand...
Click to collapse
Thats your problem! Vista is very shaky at best with flashing via USB on HTC devices.
Reflash to WM5 using the SDCard method.
Psi

this worked for me
follow the directions on this thread it worked for me http://forum.xda-developers.com/showthread.php?t=291723

Hi, all

Hi, I am new on this forum and I hope somebody can help me.
I have an Qtek 9000.
Now, he is dead.
I hope somebody can help me. (Please!!!!!)
My qtek 9000 is jammed. He does nothing more.
Try to reset., failed.
bootloader mode tried. (start-up + light + reset) failed. Only what I see = USB (on the top) and V1.00 on the bottom
Everything, also tried connecting with the PC. failed.
Il has no connection with my PC.
What I must doing now?
Can somebody help me? Thanks

Welcome to forums
Have a deep read here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
Good luck,

Thanks
Jevis

no connection with my PC
orb3000 said:
Welcome to forums
Have a deep read here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
Good luck,
Click to expand...
Click to collapse
Thanks for your advice, I have read it very carefully, but I don't get any response from my PC or device. I use Vista, is that perhaps a problem?
The device stay always on USB (on the top) and V1.00 (on the bottom)
Otherwise, when I started MTTY 1.24, it don't recognized USB, only COM 1, 2, 3.
My PC indicated USB connection, but not the device.
I can't quit the screen from the bootloader.
I am sure, I do something wrong. Please help me!!
Thanks

Vista is your problem, try it on Windows XP

to see USB on mtty, you need to uncheck the "allow USB connections" in activesync options

You can do it in Vista also
read here:
http://forum.xda-developers.com/showthread.php?t=313001&highlight=flashing+vista

THANKS EVERYBODY, IT WORKS !!!!!!
In the morning I have used the PC of my wife (XP) and it didn't work.
Now I have use the PC of my son, and it works!!(strange)
But by the MTTY I used COM1. It was flashing immediately.
I have not tried in vista. Maybe tomorrow.
Thanks for your help. Thanks, thanks.
Jer

Welcome to forum and you just learned a valuable knowledge... almost everyone at first have that problem.. I had same problem... and thanks to all the guyz here who share there knowledge and make this forum great
Enjoy you device...

other problem with my device
I will say it again, I am very pleased with your help,
Only, now I have an other problem. I will upgrade my device too http://www.qtek.nl/_BIN/UNI_DT_WWE_13077_176_10900_Ship.zip
Now it will crash again an is it back in the Bootloader mode.
I see on the top USB and on the bottom V1.00. What can I do?
Is it also possible to install Windows Mobile 6.1 on my device?
My device don't accept it.
Thanx

jevis said:
I will say it again, I am very pleased with your help,
Only, now I have an other problem. I will upgrade my device too http://www.qtek.nl/_BIN/UNI_DT_WWE_13077_176_10900_Ship.zip
Now it will crash again an is it back in the Bootloader mode.
I see on the top USB and on the bottom V1.00. What can I do?
Is it also possible to install Windows Mobile 6.1 on my device?
My device don't accept it.
Thanx
Click to expand...
Click to collapse
Try to use tomal's v8 or 9 both are great ... should not have any problem at all.... .. Try using XP it's easier...
Cheers
Rajiv

Htc Diamond does not leave the home screen and restarts constantly

PLEEEEEAAASE HEELP ME !
I got a rom for my htc diamond and after 100%, the unit continues with the same problem, does not leave the home screen and when I install hard-spl it remains 1:40 olinex not know what else to do, please help me.
PLEEASE , PLEEEASE

Hagaeminon said:
PLEEEEEAAASE HEELP ME !
I got a rom for my htc diamond and after 100%, the unit continues with the same problem, does not leave the home screen and when I install hard-spl it remains 1:40 olinex not know what else to do, please help me.
PLEEASE , PLEEEASE
Click to expand...
Click to collapse
Try MTTY , it should Help ......

MTTY is not necessary to send the Diamimg.nbh to the memory inside the unit?
I already tried but I can not use sync mode of internal memory, the unit is not at the start and restarts, I can only access the boot screen and sync with activesync windows vista.

why don't you try mtty and flash a different rom you run mitty when in bootloader read the mitty thread fully as you need to install drivers if running vista or win7

wapvirus said:
why don't you try mtty and flash a different rom you run mitty when in bootloader read the mitty thread fully as you need to install drivers if running vista or win7
Click to expand...
Click to collapse
the device does not sync with mtty , I tried on xp and mtty does not sync too