When I use my GPRS after a soft reset everything work fine but after it disconnects the first connection and I try again, the "G" icon on the top flashes, BA tries to connect but the beast is not able to connect anymore to GPRS. It gives :"Cannot connect for an unknown reason. bla. bla....". I have to reset the radio in order to make it works again.
ROM: 1.40.00 WWE
Radio 1.13.00
Protocol Version: 1337.42
ExtROM: 1.40.556 WWE
Thanks for any help
Anybody know how to fix this - I have the same problem (same rom & radio)
Thank you
You might want to try updating to a different radio ROM. There is a walk through on how to do this on the Wiki.
My BA does this too, but only in certin areas like around my home. In downtown it works perfect.
i have the same problem
i had tried radio version 2.30.xx 2.19.xx
I think there is no solution, it is just native instability of this and other ROM version(s). Mine is the same. I know people using WM5 ROMs wothout this problem.
Anyway, I put the phone in flight mode, wait some seconds, and turn off flight mode - and then connect again to gprs and it works. This way I´ve been avoiding a soft reset.
Hi Guys
I was using Black 2.0 with SPL 1.40.Olipro (HardSPL_v6) and Radio 1.41.00.10 and this afternoon decided to upgrade to Black 2.5 with SPL 2.10.Olipro
Everything worked well, until i got home, where i noticed no matter how hard i tried wifi/wlan would not detect any networks. Did a few searches but decided to go back to my previous config to see if it still worked or if i did any permanent damage to NAND/EEPROM blocks
First i tried Black 2.0 still with SPL 2.10.Olipro and Radio 1.41.00.10 but to no avail.
Next i downgraded SPL to 1.40.Olipro (HardSPL_V6) still with Black 2.0 and Radio 1.41.00.10 then everything worked!!
Immediately after that Black 2.5 went back on still with 1.40.Olipro and Radio 1.41.00.10, the moment WLAN/Wifi was enabled, a window poped up with a "New network detected" prompt.
Those with WLAN problems please try downgrading your SPL to 1.40.Olipro (HardSPL_v6) as i believe 2.10.Olipro may have some bugs?
Please post feedback for those that have tried.
Cheers!
Have you a link to download Hard-SPL V6 ?
I try with V5 and black 2.0 and no wifi start
Well, I am not sure what is posted below is necessary. I have Black 2.5 and SPL 2.10 Olipro (with Radio 1.41). My WiFi works fine ... and I did no special tweaking (other than to install the cingular settings).
HyperZ said:
Hi Guys
I was using Black 2.0 with SPL 1.40.Olipro (HardSPL_v6) and Radio 1.41.00.10 and this afternoon decided to upgrade to Black 2.5 with SPL 2.10.Olipro
Everything worked well, until i got home, where i noticed no matter how hard i tried wifi/wlan would not detect any networks. Did a few searches but decided to go back to my previous config to see if it still worked or if i did any permanent damage to NAND/EEPROM blocks
First i tried Black 2.0 still with SPL 2.10.Olipro and Radio 1.41.00.10 but to no avail.
Next i downgraded SPL to 1.40.Olipro (HardSPL_V6) still with Black 2.0 and Radio 1.41.00.10 then everything worked!!
Immediately after that Black 2.5 went back on still with 1.40.Olipro and Radio 1.41.00.10, the moment WLAN/Wifi was enabled, a window poped up with a "New network detected" prompt.
Those with WLAN problems please try downgrading your SPL to 1.40.Olipro (HardSPL_v6) as i believe 2.10.Olipro may have some bugs?
Please post feedback for those that have tried.
Cheers!
Click to expand...
Click to collapse
Can connect to router but can't locate webpage
I had flashed the rom to LVSW 23/4/07 version, everything works fine except the wifi. It can connect to the router but it can't load the webpage. It just says locating...
Please help.
ROM: LVSW 4-23 Full, Radio 1.40.30.00, SPL 2.10.Oli, IPL 1.04
I downgraded my spl to the original 1.06 and that didnt fix it
weinson said:
Well, I am not sure what is posted below is necessary. I have Black 2.5 and SPL 2.10 Olipro (with Radio 1.41). My WiFi works fine ... and I did no special tweaking (other than to install the cingular settings).
Click to expand...
Click to collapse
Well after doing a search it looks like there are others that have the same problem as myself. If everything went well for you good on ya! Im sure there are many others out there with successful flashes running Black 2.5 with SPL 2.10. Im just posting what worked for me.
xpbillgates said:
I had flashed the rom to LVSW 23/4/07 version, everything works fine except the wifi. It can connect to the router but it can't load the webpage. It just says locating...
Please help.
ROM: LVSW 4-23 Full, Radio 1.40.30.00, SPL 2.10.Oli, IPL 1.04
Click to expand...
Click to collapse
Are you getting an IP address from the router? Usually its in the format 192.168.x.y
If you have an IP beginning with 169.x.y.z then make sure DHCP server is enabled on your router's config page. Do a search im sure this has been covered here before somewhere in greater detail.
belu said:
Have you a link to download Hard-SPL V6 ?
I try with V5 and black 2.0 and no wifi start
Click to expand...
Click to collapse
Here you go
http://rapidshare.com/files/27700993/Hard-SPL-V6.zip.html
It would be nice is someone made a sticky thread with links to all the threads with this WLAN problem after flashing a rom "hint hint"
I've tried everything, including using SNIFI and SOCKET WIFI softwares to connect to my existing netgear router(WEP enable) after upgrade to WM6 Black 2.5 and Radio 1.40 but unable to detect the network . After several hours, the only solution that work is: Turn on WIFI, DELETE existing connection, and add new connection (with WEP key)- and everything works !!!! . Hope this help
pl55 said:
I've tried everything, including using SNIFI and SOCKET WIFI softwares to connect to my existing netgear router(WEP enable) after upgrade to WM6 Black 2.5 and Radio 1.40 but unable to detect the network . After several hours, the only solution that work is: Turn on WIFI, DELETE existing connection, and add new connection (with WEP key)- and everything works !!!! . Hope this help
Click to expand...
Click to collapse
So you were able to turn on your wifi but couldn't connect?
.... I am unable to turn on my wifi at all.
I am having no trouble at all with WiFi, see signature for setup details.
Had 1.41 radio first, then upgraded Black 2.5, then SPL 2.10, no reasoning for order that I did it in, just did it as the upgrades were available.
anybody knows how to configure wifi in this version?
Lurch3559 said:
I am having no trouble at all with WiFi, see signature for setup details.
Had 1.41 radio first, then upgraded Black 2.5, then SPL 2.10, no reasoning for order that I did it in, just did it as the upgrades were available.
Click to expand...
Click to collapse
Although i dont think order matters, but i did the following which didnt work for me
1. Radio 1.41
2. SPL 2.10
3. Black 2.5
Maybe i should try SPL 2.10 last now that everything is working
Btw did anyone notice a slight decrease in speed/response from Black 2.0 to Black 2.5?
Firstly, thanks.
I have checked it, I can get IP from the router.
I did a Textbook upgraded based on "Mr Vanx" upgrade guide to Black 2.5/1.41.00.10/2.10.Olipro (HardSPL v7)
every thing works perfectly except I can connect to my Netgear wireless router, it detects it and ask for the key, but will not connect.
Not with WPA-WSK or WEP, I have tried everything (removing settings, upgrading router firmware changing from G to B, Hard Reset and not a sausage, it was worked perfectly before the upgrade.
Wififofum2 detects in but failes to recognise the type of security.
I am going to try putting the retail imate back on
I'm on Black 2.5, 1.40 and Wifi turns on, does not detect the network... even with a manual CONNECT through connections
Let it sit a while, with wifi on, 10 minutes maybe, then it decides to pop up Network Detected... truly weird..
Same NO Wifi Issue here too
Running all latest ROMS (see my sig.)
When I turned Wifi, it appears from the device to be working, but it did NOT pick up any signal at all. But...
I DID get Wifi to finally come on, I believe, by turning OFF my Cellular signal in the Connections app, and then turning on Wifi. I think it took a couple of mins to popup, saying my ssid was found at that point.
If anyone finds a real solution, please post!
Hi guys,
I've been reading the forum long time and this is my first post.
My phone is Softbank X01HK and I am currently running Black 2.5 with the buzzing cap, SPL-2.10-Oilpro and Radio 1.38.00.11. My phone works well on Wifi, HSDPA, GPRS-EDGE and GRPS. I have 2 phone numbers with 2 different provider in Hong Kong, Hutchison 3-HK and Peoples.
I used to have SPL-1.40-Oilpro and until yesterday I flashed to SPL-2.10-Oilpro. Surprisingly but weird, I have found my 3G reception at home gets 1 to 2 bar better right after I have SPL-2.10-Oilpro installed. It is so weird cuz I thought the boot loader has nothing to do with the 3G reception, also, everything else still works without any noticeable different.
I was planned to upgrade my Radio Rom to 1.40, but I think I'll stick with 1.38.00.11 for while.
Hope this help
pl55 said:
I've tried everything, including using SNIFI and SOCKET WIFI softwares to connect to my existing netgear router(WEP enable) after upgrade to WM6 Black 2.5 and Radio 1.40 but unable to detect the network . After several hours, the only solution that work is: Turn on WIFI, DELETE existing connection, and add new connection (with WEP key)- and everything works !!!! . Hope this help
Click to expand...
Click to collapse
cheers!!! this one works for me.
Hi everybody,
i tested a lot of radio rom so far and i still have an issue.
Sometimes during the boot the 'no gsm' message appears and i need to reset the device to let it works.
Other times during the day it looses the signal and freeze.
Actually i'm using the schaps 4.00 and rom 1.47.0.10.
I use a 3 and a wind sim as backup.
Any ideas? Something corrupted or the device has some problems?
Thanks
Acr
the same thing happens to me except with the 1.54 radio, most other radios that i have tried say that i don't have a sim in or unknown sim status and ask me for a pin.
Hi,
the same with 1.54 radios. Well.. a little less..
So i suppose it's something dealing with the radio and not the device itself.
Any other experience guys?
Hi,I have an xda orbit (O2 uk) and I ran the USPL super CID on it which went thru fine. I then did an OS upgrade from the official O2 website to WM6. However my phone wouldnt make calls or accept calls. The signal bars were initially low which made me suspect the radio not being optimum. Tried to upgrade the radio from 3.06.90 to 3.08 or 3.19 but it kept on giving an error 270 - file corruption,tried flashing to another rom and still the same error.I then tried to re -USPL it and even that wont take... Can someone please help me out with this as I am at my wits end to a solution...Thanx a lot
still sweating....
ok...update so far...repeated the flash over and over again, Hard reset and moved the enable and cert rapi to the xda and ran them there first after taking out the sd card. finally it took after a few more atempts. I then ran artemis 20273 rom which flashed easily....HOWEVER even though the signal bars are still up I cant call out or receive calls. Dialling out ,the call disconnects immediately even before it rings (like 0.5secs after i hit the send key). If I call the phone I get a message that calls are not currently being connected to that number! (i know the sim cards working as its my main number) Anyways run uspl again and flash radio to 3.18...goes thru easily but still no calls in and out. Is there anyone with an idea as to the problem or solution.
Since I flashed 6.1 (did superwipe yes + flashed new radio) wcdma,gsm netorks are unresponsive, calls are ok... wifi is limited to 800Kb/s... Everything except this and common 720p video problem, is ok.
To understand if this is caused by redio or kernel, i reverted back to 11m2 radio with ril. , no change... tried LordmodNC 2.1 still the same...
And something strange; when on mobile network (not wifi) i can use internet connection only by default browser, nothing else can get online
Please help
ozguroge said:
Since I flashed 6.1 (did superwipe yes + flashed new radio) wcdma,gsm netorks are unresponsive, calls are ok... wifi is limited to 800Kb/s... Everything except this and common 720p video problem, is ok.
To understand if this is caused by redio or kernel, i reverted back to 11m2 radio with ril. , no change... tried LordmodNC 2.1 still the same...
And something strange; when on mobile network (not wifi) i can use internet connectiononly by default browser, nothing else can get online
Please help
Click to expand...
Click to collapse
try to flash the rom again after one more superwipe.......
Superwiped, flashed again... Still no change
everything is smooth and stable.
Wifi and gsm still the same as 5.6.2
I changed my sim card (AVEA, another operator) it was able to connect normally wcdma and gsm... Put back my vodafone sim card which i normally use, and it is working now!?
About wifi, i rebooted my wifi router, and its working now too...
So in short words, both my router and GSM network failed at the same time?!? really weird coincindence... ?!?!
no issues for me, new radio and ROM have improved my 3G and Wifi connection
how does it works on arhd 6.1.5?