[Q] Cradle / dock that accomodates EVO with case? - EVO 4G Accessories

Hi all,
I am looking for a desktop cradle / dock that accommodates EVO with case. Any suggestions? I searched a lot but couldn't find one.
Regards,
KS

Depends partly on which case you're using. A universal mount which works by clamping onto the outer edges of the phone with foam-rubber fingers won't much care what it's holding. They're available as windshield mounts, vent mounts (for those keen on finding out just how delicate those vent vanes used to be, before being ripped out by a vent mount) and dash mounts.
If you're rich, and paid enough to get a Seidio wideass battery, their new mount is built to hold it with the fat case on it, but they'll knife you fifty bucks for it.
If you use the kind of case that hugs the phone from the back, you can either glue a mounting lug onto it which mates to a dash mount, or do the same to a spare case.

Seidio Innodock Jr. Desktop Cradle for HTC EVO 4G
http://www.amazon.com/Seidio-Innodock-Desktop-Cradle-Black/dp/B003QXN9ME
Works perfectly with my Seidio innocase!!

imex99 said:
Seidio Innodock Jr. Desktop Cradle for HTC EVO 4G
http://www.amazon.com/Seidio-Innodock-Desktop-Cradle-Black/dp/B003QXN9ME
Works perfectly with my Seidio innocase!!
Click to expand...
Click to collapse
I have this dock and it is a good dock. It will accomodate either cased or non cased EVO's. It also slightly lays your EVO back so as to not be in a 90° angle and can be leaned forward so as to see the screen better while laying in bed and then released and it sits back again. It's pretty tiiite.

AcIdC0R3 said:
I have this dock and it is a good dock. It will accomodate either cased or non cased EVO's. It also slightly lays your EVO back so as to not be in a 90° angle and can be leaned forward so as to see the screen better while laying in bed and then released and it sits back again. It's pretty tiiite.
Click to expand...
Click to collapse
Thanks you all for the response. It doesn't have a great feedback on Amazon but I will give it a try.

Related

ProClip Evo Mount Now Available

http://www.proclipusa.com/brodit-de...t)/holder-with-tilt-swivel--511176-18252.aspx
http://www.proclipusa.com/brodit-de...-cigarette-lighter-adapter--512176-18252.aspx
http://www.proclipusa.com/brodit-de...ord-for-fixed-installation--513176-18252.aspx
http://www.proclipusa.com/default.a...d=&parent_category=4&d_pcat=13722&d_cat=18252
For those wanting a quality car mount, here it is. ProClip stuff is awesome. Its pricey but it works.
Completely worth it if you go with the fixed install.
I just ordered mine, I've always loved proclip.
Ordered!
I've been waiting for this bad boy to come out.
I wish that they would sell the basic holder without the swivel. I think that the entire mounting system looks much better without it. Oh well I'll just throw it in a box like I did for my G1 swivel mount.
I have a N1 ProClip holder somewhere around here. I need to see if I can figure out a way to mate it to a quality suction cup mount. If so, Ill get the Evo one.
do u guys know if the non-adjustable one works w/ the innocase II case? doesn't look like it, but figured i would ask....
this can be in landscape mode no problem huh? i should mention and it stays in landscape mode without any movement?
i bet this would work nice with an otterbox too...
hmmmmm
any videos anyone?
I dont think it swivels without leaving it loose.
I was thinking about it, but it us too expensive,i might just try a cheapo vent mount one to start
Sent from my HTC Evo 4G using XDA app
An alternative to Brodit/ProClip?
I'm sure this will work:
http://cgi.ebay.com/Car-Dash-Air-ve...80550909556?pt=PDA_Accessories#ht_1166wt_1137
Yeah, it's for an HD2 but it may work..the Evo is just a fraction of a millimeter thicker, but essentially the same dimensions. The holder is wide open so all the buttons are exposed including a hole in the back of the holder for the speaker/camera. Even if I have to mod the holder a little once I have it, for $7 and free shipping and it fits on a standard Nuvi mount, which I got rid of anyway now that I have the phone's better Navigator....I'll take a chance with it before spending over $50 for a product that does the same thing. Just my two cents.
It should be here in a couple of days, as I ordered it about 5 days ago....I'll let you all know how it works out.
Cheers
i guess im out of luck since im using the sedio rugger holster.
shad0w77 said:
do u guys know if the non-adjustable one works w/ the innocase II case? doesn't look like it, but figured i would ask....
Click to expand...
Click to collapse
the proclip one does not, but the slipgrip holder does. I took one of my old TP2 proclip mounts' ball joints and adapted to the slipgrip, its somewhere in the post where the slipgrip is reviewed in this forum
Mayonesa said:
i guess im out of luck since im using the sedio rugger holster.
Click to expand...
Click to collapse
Use the ProClip iPhone holder that they also suggest for EVO's with cases.

Looking for a windshield mount for my truck

I know there a few threads about windshield mounts but none of them have what I'm looking for. I am looking for a windshield mount for my 2000 Ram 1500. I want it to mount on the BOTTOM on the windshield and come to the edge of the dash so it will need to be fairly long. I switch between the Seidio Innocase II surface and the Seidio 3500mah extended battery so I need something that will accommodate both of those. I also need it to switch between portrait and landscape. The Kensington windshield mount for the Iphone looks like it would be great but it doesn't look like it will allow me to use my extended battery.
What have you guys found that might work for what I need?
ive been using this...
Scosche IUHW7 Windshield Vent Mount Kit.
its inexpensive it sitcks... it turns and fits all kinds of stuff
I think I got it for 12 bucks at walmart
bacidath said:
ive been using this...
Scosche IUHW7 Windshield Vent Mount Kit.
its inexpensive it sitcks... it turns and fits all kinds of stuff
Click to expand...
Click to collapse
I might have to see if my local walmart has that. Thanks.
http://www.seidioonline.com/product-p/ck17hev4c04.htm
it is not long but with a little modification it will work.
it also holds thee innocaseII and the extended battery one.
will car dock the phone
Ram Mounts are good in trucks
http://www.ram-mount.com/
Mountek MT5000
I bought this after finding a thread about it on another forum. Best accessory ever. Extremely quick and easy to install, rotates portrait/landscape ... can't complain about anything. It uses your CD slot - you just put it in the opening and clamp it down.
It's actually started to become a problem because I'm constantly distracted while driving by my cellphone now. It's just right there up in my face, gorgeous and begging to be played with.
Can't post the link since I'm new here ... but you can Google it easily.
I like the Clingo mount so much, I am going to mod the Sedio Active Innocase I have to make it work with it (smooth.velvty doesn't stick to Clingo).
sanyi83 said:
Ram Mounts are good in trucks
http://www.ram-mount.com/
Click to expand...
Click to collapse
I've used Ram Mounts in my Jeep, good stuff!
Sent from my Desire HD using XDA App
I've got a cheap Arkon universal mount I use in my car. Works great with my ballistics case or naked.
Dunno how long it is but I have am ikd z car and its mounted to the bottom of my windshield and comes to the dash edge. Probably 6in or more. It was tricky too cause my car has a high rake angle and I wanted it mounted so it wouldn't show Tue mount at all in videos. It does block half the camera but it clamps hard enough that you can scoot it up and get the camera free.
Sent from my (insert daily ROM name here) Evo 4g
When in its case, mine fits in my Garmin windshield mount
Sent from my PC36100 using XDA App
Why not just get the seidio innotraveler? It will fit both the extended battery and innocase power their website. I have it and love it, it actually extends pretty far.
Sent from my hand with XDA Premium installed
Because the seidio one is $50! Thats crazy for a windshield mount. I found one at bestbuy yesterday its by rocketfish and made for the iphone but it works with our phone to. It doesn't come to the edge of the dash but it will work.

Proclip mount shipping - works with extended battery!

Good news for all you Proclip fans,
I just recieved mine today and it works with the Samsung Extended battery just as well as the standard battery. There is a 1/2 in space behind the phone that should allow for even the most extreme extended batteries to fit as long as the battery cover does not extend beyond where the original battery cover fits (like if it wraps around the side of the phone it will not fit).
I ordered Proclip part number 513331 (Hard wired install).
Proclip doesn't disappoint either, this mount is just as awesome as the one for my old DINC. Nice and sturdy.
I'll post some pics later when I get it installed.
As is typical with proclip mounts, the mount is designed based on the physical dimensions of the phone (specifically the sides of the phone) so cases that change those dimensions will cause the phone to not fit in the grooves correctly.
Pix of the proclip in action
Grabbed a couple of pics for anyone interested.
Looks good, I had the incredible one too, but imo it was a little to hard to get in and out. Unfortunately since I already chipped my phone, I'm too scared to go naked with this phone. Plus their price is just too high for me.
Sent from my Galaxy Nexus using xda premium
T-Keith said:
Looks good, I had the incredible one too, but imo it was a little to hard to get in and out. Unfortunately since I already chipped my phone, I'm too scared to go naked with this phone. Plus their price is just too high for me.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
I wont argue that they are spendy - I already had the base part but it's like $100 for both pieces for newbies.
But I do get something that no other mount has been able to offer me - this one is wired into the car, I can use only one hand to put my phone in it, and it doesn't fall or move when I press too hard. Considering the Verizon one is $40 and a POS it seemed worth the extra.
But yea if you have a case it's not so good.
does you phone fall if you turn the screen for navigation ?
I just ordered Proclip's adjustable mount 875214. Hopefully it will work well with my diztronic case. It grips near the bottom of the phone so it shouldn't interfere with any of the buttons or ports. I'll update after it arrives with the results!
roachdabug said:
I just ordered Proclip's adjustable mount 875214. Hopefully it will work well with my diztronic case. It grips near the bottom of the phone so it shouldn't interfere with any of the buttons or ports. I'll update after it arrives with the results!
Click to expand...
Click to collapse
Should be good, as it is adjustable. I wish they made the sides of the powered mount adjustable...
juju2lose said:
does you phone fall if you turn the screen for navigation ?
Click to expand...
Click to collapse
Nope, it stays in there really well.
roachdabug said:
I just ordered Proclip's adjustable mount 875214. Hopefully it will work well with my diztronic case. It grips near the bottom of the phone so it shouldn't interfere with any of the buttons or ports. I'll update after it arrives with the results!
Click to expand...
Click to collapse
Well for those who aren't aware, these Proclip holders come in 2 pieces: The first is a custom-fit bracket for your particular vehicle, and the other is the actual phone holder.
So let me start with the holder. The one I got is adjustable and holds my Galaxy Nexus with Diztronic case extremely well. It's snug but not difficult to remove, and leaves plenty of room behind the phone for the craziest of extended batteries. A+
Then there's the mounting bracket... I selected 853616 for my '07 Impreza. It hooked in behind the panel just fine and it is made of the same plastic as the holder which was nicer than I expected.
Unfortunately, it goes downhill from here: This particular bracket is a bad fit. All the angles are off, and as a result the adhesive backed sections do not contact the vehicle properly. Even if they did, the adhesive is so weak that I'm not sure it would stick. I'm going to have to pull it all apart and go to work with some thick double-sided adhesive tape of my own in order to deal with the gaps and get it installed properly. Not cool, especially considering the whole kit ended up costing me about $60. Now, there's lots of different brackets for lots of different cars out there, so your mileage may vary.
At any rate, it does a much better job holding the phone than my cupholder did.
Got mine a couple of days ago.
As has been noted, they come in two pieces. The piece that holds the phone is very, very nice and will definitely work with any reasonable extended battery. It's very snug, but not too snug, and the fit is perfect. I got one of the powered versions and it's fantastic.
The car mount piece, for me, is of similar quality. The fit is near stock and the thing is damn near impossible to remove.
As a unit, the two pieces are rock solid.
Highly recommended. I wouldn't hold out for the Samsung three pin holder. I had that same holder (minus the three pins, obviously) for my Nexus S - and this one is far, far, far better.
roachdabug said:
Well for those who aren't aware, these Proclip holders come in 2 pieces: The first is a custom-fit bracket for your particular vehicle, and the other is the actual phone holder.
So let me start with the holder. The one I got is adjustable and holds my Galaxy Nexus with Diztronic case extremely well. It's snug but not difficult to remove, and leaves plenty of room behind the phone for the craziest of extended batteries. A+
Then there's the mounting bracket... I selected 853616 for my '07 Impreza. It hooked in behind the panel just fine and it is made of the same plastic as the holder which was nicer than I expected.
Unfortunately, it goes downhill from here: This particular bracket is a bad fit. All the angles are off, and as a result the adhesive backed sections do not contact the vehicle properly. Even if they did, the adhesive is so weak that I'm not sure it would stick. I'm going to have to pull it all apart and go to work with some thick double-sided adhesive tape of my own in order to deal with the gaps and get it installed properly. Not cool, especially considering the whole kit ended up costing me about $60. Now, there's lots of different brackets for lots of different cars out there, so your mileage may vary.
At any rate, it does a much better job holding the phone than my cupholder did.
Click to expand...
Click to collapse
How snug of a fit is it? I have Verizon galaxy nexus with extended battery and Diztronic case. Does it take quite a bit of pressure to put it in the holder? Also, is the headphone jack open at the bottom?
Sent from my Galaxy Nexus
roachdabug said:
the adhesive backed sections do not contact the vehicle properly. Even if they did, the adhesive is so weak that I'm not sure it would stick. I'm going to have to pull it all apart and go to work with some thick double-sided adhesive tape of my own in order to deal with the gaps and get it installed properly.
Click to expand...
Click to collapse
That's what I had to do for my wife's Civic. She got the car mount that affixes to the center console and that one piece of double sided tape just wasn't cutting it. I used a heat gun to remove the factory tape and then liberally applied tape to all parts contacting the console. It's been holding steady for over a year.
Proclip should probably give people more sticky tape - but I think the reason they only use a single piece is because they tout that the proclip doesn't damage the car and it could be argued that uber liberal amounts of double-sided sticky tape could potentially damage some surfaces. In the civic it’s all plastic so it’s NBD to use a heat gun and remove any residue, but if was a BMW with an oak dash then I could see people complaining.
dgwood12 said:
How snug of a fit is it? I have Verizon galaxy nexus with extended battery and Diztronic case. Does it take quite a bit of pressure to put it in the holder? Also, is the headphone jack open at the bottom?
Sent from my Galaxy Nexus
Click to expand...
Click to collapse
I don't think any case would work with the proclip because it is a very snug fit and yes it takes a fair amount of pressure to put it in. Not so much that it will move the dock but certainly enough to keep the phone from coming out accidentally.
The only reason the extended battery works is because there is nearly a 1 inch opening behind the phone and the battery cover does not extend to the edge.
Yes the headphone jack is open but you would need a connector that is straight. A 90 degree connector would not work.

S3 Suction car mount by Garmin!!

By pure chance I found out that my SIII with its slimline cover fitted works perfectly in my Garmin Nuvi 205 dash mount.
Secure and easy to mount, almost as if it was made for the S3.
The Garmin Part Number
Item 010-10936-00 Suction cup with bracket (Nuvi 2xx series)
Cost is around $10 - %15
Cover is a Cygnet BlackFrost Matte slim case (around $20)
I love finding a really good cost effective solution for my toys!!
Video Clip. Please excuse poor sound quality, had to dig out my old Olympus compact to make this,
Thanks, looking forward to the video.
good to know since Garmin has quality mounts.
Does it actually clip in? Is it firm?
If you remove the case, hows the fit?
Fits snugly, clips into the mount as if it was made for it,
Doesn't work without the cover though, phone is just to small,
Would be possible rather easily I might add to put some shrink tubing on the arms of the mount and build it up a little to hold the phone naked!
I wonder if it would fit with a tpu case. Your case seems pretty slim
ZaJules said:
By pure chance I found out that my SIII with its slimline cover fitted works perfectly in my Garmin Nuvi 205 dash mount.
Secure and easy to mount, almost as if it was made for the S3.
The Garmin Part Number
Item 010-10936-00 Suction cup with bracket (Nuvi 2xx series)
Cost is around $10 - %15
Cover is a Cygnet BlackFrost Matte slim case (around $20)
I love finding a really good cost effective solution for my toys!!
Click to expand...
Click to collapse
Thanks for the find. Do you think it would be able to fit the S3 with an Otterbox Commuter case on? My phone's approximately 7.7mm wide with the case on.
Cheers
Might fit but it would be tight, the rounded edges of the Cygnett case allows it to clip into the holder the otter box might be to square
Sent from my ASUS Transformer Pad TF300TG using Tapatalk 2
my garmin gps always falls off from the windshield now..the suction cup doesn't hold..don't know how i'd feel putting my phone there..
am i suppose to wash it with soap or something to make it work again?
kl25 said:
my garmin gps always falls off from the windshield now..the suction cup doesn't hold..don't know how i'd feel putting my phone there..
am i suppose to wash it with soap or something to make it work again?
Click to expand...
Click to collapse
You should get a replacement one...They are super cheap on eBay. I have one that is over 7 years old (*back when standalone GPS units were +$300!) and it still works great.
kl25 said:
my garmin gps always falls off from the windshield now..the suction cup doesn't hold..don't know how i'd feel putting my phone there..
am i suppose to wash it with soap or something to make it work again?
Click to expand...
Click to collapse
I fix that with alcohol. But then I fix everything with alcohol.
universal mount
I got this car mount from amazon.com
Search for Kropsson Aero universal mount.
the design of the mount was a great plus.
Feature wise, defiantly recommend.
proud a-clown said:
I fix that with alcohol. But then I fix everything with alcohol.
Click to expand...
Click to collapse
:laugh::good:
couldn't have said it better myself!!!!
I can confirm this mount works great with the rock quicksand case. Easy to put in and take out and holds rock solid. Before the case showed up I had used a couple pieces of heat shrink tubing held on with electrical tape and it worked awesome with the naked galaxy s3.
I like this style of mount because you can position the phone with it gripping the middle, top or bottom to fine tune where the screen is in relation to your windshield.
I went with this one though, instead of one of the $5 options: (replace spaces with ., I don't have enough posts to post links) www amazon com/gp/product/B0042PJ8NY/ref=oh_details_o00_s00_i00[/url]
It's the actual oem garmin mount instead of a knockoff, and judging by the reviews the difference is the mount that holds the ball is made of metal, so it won't break. It came with one of the 3m PE Foam adhesive backed discs for mounting to the dashboard as well. Highly recommended.
I just tried it. PERFECT fit with my diztronic TPU case. Thanks OP!

Flip Cover + Car Mount?

I currently use a back cover and a simple car mount on my N5, but would prefer to use a flip cover. But my last faux leather flip cover was destroyed by the car mount.
So I'd like to know if there's a car mount that is flip cover friendly, or a flip cover that's car mount proof. It also needs a way to keep the cover open somehow. Thanks
the_rebel said:
I currently use a back cover and a simple car mount on my N5, but would prefer to use a flip cover. But my last faux leather flip cover was destroyed by the car mount.
So I'd like to know if there's a car mount that is flip cover friendly, or a flip cover that's car mount proof. It also needs a way to keep the cover open somehow. Thanks
Click to expand...
Click to collapse
I personally haven't seen one, but I thought about it when I got those clamp mounts where it clicks with enough pressure on the sides and the phone is clamped by rubber inserts. I tried it with my Seidio Ledger flip case and can be used if you flip the case landscape where the flap would fall open with gravity. I would not suggest folding it back fearing that the case may get damaged at the hinge or front flap.
Here's a car mount I reviewed, but you can use anything that are like the montar mount I reviewed.
http://forum.xda-developers.com/goo...i-review-winnergear-montar-universal-t2627658
Thank you for the review and pointing me towards it. I'd have guessed that the slight curve on the arms of the car mount would push the flip cover towards the screen, partly hiding it - but the pics you have posted tell me that's not the case.
Have you used the cover and mount for long? Did the cover suffer any damage from repeated mounting?
the_rebel said:
Thank you for the review and pointing me towards it. I'd have guessed that the slight curve on the arms of the car mount would push the flip cover towards the screen, partly hiding it - but the pics you have posted tell me that's not the case.
Have you used the cover and mount for long? Did the cover suffer any damage from repeated mounting?
Click to expand...
Click to collapse
Tell you the truth, the flip case is really not condusive to car mounts. I really didn't fee all that comfortable using it with the car mount for a long amount of time. Getting it out and in is a pain in the butt lol. But maybe something like a spring loaded one that can release may work better than this one.
Exactly! And those fears aren't baseless. Like I said, my earlier flip case was destroyed this way.
Anyway, I found a really cheap car mount, unlike anything I've seen before and ordered it right away, it holds the phone vertically instead of horizontally and attaches to the steering wheel, so flip cover should be alright, though I'll have to see how it affects the charging port....
Anyway, its less than $1.5 so I don't mind trying it out. Link
the_rebel said:
Exactly! And those fears aren't baseless. Like I said, my earlier flip case was destroyed this way.
Anyway, I found a really cheap car mount, unlike anything I've seen before and ordered it right away, it holds the phone vertically instead of horizontally and attaches to the steering wheel, so flip cover should be alright, though I'll have to see how it affects the charging port....
Anyway, its less than $1.5 so I don't mind trying it out. Link
Click to expand...
Click to collapse
Cool...hmm..tension mount. Interesting. Let me know how it turns out! Yea, for that price, I would experiment too lol.

Categories

Resources