radio upgrade - 8525, TyTN, MDA Vario II, JasJam ROM Development

hi all when I try to upgrade my radio ROM through activesync it says connection error. Then I get stuck in the bootloader, so I try doing it trough storage card then it only gets about 1/6 of the way, and freezes, I have left it overnight and no progress. So then I have to flash a full ROM to get it start up, but I really need a new radio because mine doesn't give me any signal for about a mile were I live
thanks in advance

If you're running xp right click the activesync icon in your taskbar.
Then go to connection settings deselect all options except for the show status icon in the taskbar option. Enable them after the update.
Put your device in bootloader mode manually (Press the ok and power button together while restting from down ) hold the two buttons until the bootloader screen appears, attach your device to the PC then run RUUWrapper.exe.
Hope I could help .

Related

WM6.0 of Hx2000 series (BUGS & Solutions)

Okay, lots of hx2000 users already flashed their roms, now facing the bugs:
# A2DP not working, please try this software. It might work for your IPAQ hx2000 series.
Attached Bluetooth Audio Router. Please give me reports if it works.
# Battery Drained Issue: Have you ever left your Pocket PC in your bag for the night and the next morning discovered that the handheld’s battery was flat?
ActiveSync
1) Go to Start> Program> ActiveSync> Menu> Add Server Source, under Server address put 1.1.1.1.
2) Tap Next (bottom right)
3) You’ll get three boxes to fill in: Username, Password, Domain. Fill in xxx in all, tap Next, Finish, Menu, Schedule
4)Peak times> change to manually
5) Off-peak times> change to manually
6) On top right click Ok
7) On bottom right click Menu> Options, on bottom middle click Delete, when you get the warning, click Yes.
You're all done. If you follow this fix correctly (as was originally stated above, it will almost always (as it would appear by others posts( fix the battery drain issue.
Messaging Accounts (Outlook Mobile)
Open up the messaging application. Tap Menu > Tools > Options > select the email account you wish to change, then tap Next > Next > Next > Options button. Remove the checkmark in the box next to "Connect and check for messages every xxx minutes." Then tap Next > Next > Finish.
Notifications
Tap Settings > Personal tab > Sounds & Notifications icon. Select the Notifications tab, and then tap the down arrow next to the Event dialogue box. Select the “Reminders” event and make sure "Repeat" is not checked.
Today Timeout
tap Start > Settings > Today icon > Items tab. Remove the checkmark next to “Today timeout” to disable the feature
HP Protect Tools
Do not use this, except you work for FBI and has lots of secret data.
Running Applications
Tap the Running Programs tab, select the application you wish to close, and tap the Stop button (or you can tap the Stop All button to close all running applications). Be sure all applications closed before turning off your IPAQ.
Power Setting
Pocket PC devices that are running Windows Mobile turn on at midnight to search for appointments for the coming day. Reminders are set and the Today view is updated with the day's events, thus on Battery power, turn off device if not used for 1 minute, Backlight on battery power: 30 seconds.
You can adjust whatsoever you want, the rule is turn off device > turn off backlight.
TODAY Plug-ins:
Better you uninstalled all today plug-ins thrid party progs.
Installed programs on SD/CF running in memory sometimes not respond after you turn on from automatic battery turn off.
It takes between 3-5 seconds to get response and/or sometimes program automatically closed by itself.
Solution: installed the programs in DEVICE.
Tips: Remove any unnecessary files in memory storage, so you will have more ROM memory storage.
After I turn on the device(2490b) from automatic battery turn off every time the backlight on battery power change to 10 seconds, no matter which setting I was choose. Until the device power off(auto or manually) the setting works, but after power on the setting change to 10 seconds again. Have anyone else this issue? Any solution?
dancer_69 said:
After I turn on the device(2490b) from automatic battery turn off every time the backlight on battery power change to 10 seconds, no matter which setting I was choose. Until the device power off(auto or manually) the setting works, but after power on the setting change to 10 seconds again. Have anyone else this issue? Any solution?
Click to expand...
Click to collapse
Uhmm strange, try to do clean reset whether the symptom disappear.
BT phone manager that you missed in wm6.0
extracted from WM5.0
Dear All,
Please pay attention that after making changes, installing new software or doing your usual software settings it is advisable to power off your device before soft-resetting.
Example, I recently setup my Inbox mail accounts and soft resetted my device in a usual way. After a soft reset I found out that none of my accounts was actually kept. So, I did setup again, powered off my device and soft-resetted it. After soft-reset all mail accounts were saved and were workable
To limit CPU Usage
1.Do the Activesync Fake server trick then turn all schedule to manual
To prevent Compaction
1.As much as possible free your program memory and install all programs in the SD of CF (if possible)
2.Move all cache to SD or CF (memmaid or SKtools can do this)
Registry: ActiveSync Manually
The above Activesync fix will also fix the problem many are having with not being able to turn on their WM6 unit.
JUST TO MAKE SURE ACTIVESYNC IS MANUALLY ACTIVATED:
You can also check the following registry entry:
[HKEY_LOCAL_MACHINE\System\ActiveSync\Engines\{176F 4FFD-F20C-4bd4-BDD7-01D0726C567B}\Settings] SyncAfterTimeWhenCradled (x)
Where x is one of the following:
0=Manually synchronize
5=5 minutes. Default value.
15=15 minutes
30=30 minutes
60=60 minutes
120=2 hours
240=4 hours
Here is real fix for A2DP problem on any custom hx2000 firmwares (e.g. 3.50, 3.52, WM6).
Download this cab file: Udillak_A2DP_Fix_for_hx2000_custom_firmwares.cab
Install it, make softreset and relax with working sound and controls of your bluetooth headphones.
Hello,
Since I've installed WM6 on my hx2790b it's great for everything but the PIM...
It's impossible to add a contact, an appointment, etc... It tells me "An unexpected error has occurred in this program." And it's impossible to synchronize the PIM with my PC
Any idea ?
Try to flash rom again, but you must do clean reset before (holding 1+power+3+ and stylus-reset). After successful update, u must do a clean reser again (on screen "formatting ps").
Synchronizing with PC, you must use the latest ActiveSync 4.5.
MightyBob said:
Hello,
Since I've installed WM6 on my hx2790b it's great for everything but the PIM...
It's impossible to add a contact, an appointment, etc... It tells me "An unexpected error has occurred in this program." And it's impossible to synchronize the PIM with my PC
Any idea ?
Click to expand...
Click to collapse
Calibrating your Battery
Read this:
http://h41206.www4.hp.com/webapps/IV3/adddoc.iv?locale=en_us&type=rep&prodSeriesId=349051&target=/NL_HW_IPG_iPAQ_common_EN_01_E/Resets/AllipaqsPoweIssuesBatteryCalibration.html&node=prodITRC/NL_HW_IPG_iPAQ_common_EN_01_E/N1|4|2|3&prodTypeId=215348&serverId=1
Calibrating your Battery
Power issues you may experience with your iPAQ over time:
* Unit fails to Power On
* Unit fails to charge 100% only holding 50% of the charge
Important: If you experience problems with power on your unit the fault may not be with the main battery. Swap testing the battery with a known good working battery may show the same fault. Calibrating your unit by running the 'Battery Calibration' test may resolve 'Power Related Issues'. You must follow the tests below exactly for good results.
1. Charge the unit for 30 minutes (No More, No Less) only powered by AC Adapter and 22-pin connector and not connected to the PC/Cradle (make sure the unit is switched/powered off).
2. Remove the power and full 'Hardware Reset' and then 'Soft Reset'.
3. Charge the unit again for 4 hours connected to ac power only. By following the procedure exactly as outlined in the steps above this will enable full calibration of the battery with the unit (make sure the unit remains switched/powered off during this charge period).
Note: After a software reset the power Leds (Light Emitting Diodes) should now be on and the battery should be showing 100%. If the unit still fails on power do the following checks:
*Test the AC Adapter at another location/power source.
*Swap test The AC Adapter if possible.
THIS WILL HELP BATTERY DRAINED ISSUE of WM6.0 in some HX2000 series; USING SKTOOL or MEMMAID:
1. KILL BioDtect in Windows Startup
2. Set Credant Manager in StartupService as MANUAL and STOP.
3. Set Standby into 24 Hr in Power Setting
4. Soft reset
5. DO NOT EVER EVER RECHARGE YOUR IPAQ USING USB in the CRADLE!!! RECHARGE YOUR IPAQ USING CABLE POWER SUPPLY ADAPTOR!!!
Bricked My Ipaq! hx2795... HELP!!
Hi,
I just got an Ipaq hx2795 and I upgraded to WM6, and it worked perfectly!. However, I saw a supposedly upgraded version of WM6 and i tried to install it, and too hastily I think. I did it without first removing my SD and CF cards. the upgrade said it went through ok on the PC, but it froze on the PPC, about halfway. ever since then, I've only been able to bring up the pda in pre-BL mode. Whenever I attempt to re-load any ROM (WM5 or WM6), I get the error message that the language of my current ROM is unknown and hence, the upgrade cannot go through. To further complicate my problem, I was trying to recover it about 3 nights ago and accidentally left the pda on all night in pre-BL mode. Now I think the battery is dead and I do not know how to charge it. Is there any resource or anyone that can help me with this problem? Is there a way to load the rom and Ignore the language setting on the Ipaq? What should I do now? HELP!!
Please let me know ASAP and Thanks!!
reggae,
You didn't follow step by step the flashing ROM procedure....please read it carefully...as written at: http://forum.xda-developers.com/showthread.php?t=329079
BEFORE FLASHING ROM: MAKE SURE IPAQ HAS BATTERY POWER ABOVE 80%
AFTER FLASHING ROM YOU MUST: CLEAN RESET AGAIN (FORMAT P.S.) and SOFT reset.
GOOD LUCK!
abbaml said:
reggae,
You didn't follow step by step the flashing ROM procedure....please read it carefully...as written at: http://forum.xda-developers.com/showthread.php?t=329079
BEFORE FLASHING ROM: MAKE SURE IPAQ HAS BATTERY POWER ABOVE 80%
AFTER FLASHING ROM YOU MUST: CLEAN RESET AGAIN (FORMAT P.S.) and SOFT reset.
GOOD LUCK!
Click to expand...
Click to collapse
Thanks for the assistance, however the flash keeps on saying that my pda's language is "unknown" and hence stops the upgrade as a result. What do i do about this?
Thanks
WM6 hx2795 and WiFi
Hello everyone,
I just came across this forum today, and was very happy to. I flashed my rom from wm5 to wm6 and definitely like wm6 more.
Now for my bug. I'm using an hx2795. Wi-Fi worked in wm5, now after I flashed the WiFi manager will connect to a AP then says 'Driver not loaded.' and disconnect. I saw Anavas' post in the "i will pay..." thread and said that wifi was working on his. So, I'm guessing it's possible to have wifi on this model. I'm hoping he/she or someone else can help me out? It's just strange that it seems to start working (can shortly do SiteSurvey as well sometimes)...
As can be guessed the driver update from HP doesn't work (incorrect revision error).
Resetting makes it works for a short time, but then I get the 'Driver not loaded' thing.
/* EDIT
* This only appears to happen when in the cradle. I took it out and it didn't give me anymore problems...weird, maybe something to do with connecting through usb vs wi-fi conflict?
*/
Thanks a bunch.
CE OS 5.2.1437 (Build 17944.0.3.1)
hi,
I checked with my hx2795 and I don't have any problem connecting WiFi so far,
I can able to connect it from my home and the office.
I even checked with the cradle, I have no problem,
Have you done a hard reset once you flashed the ROM, or did you install any other driver / software ?
I used my ppc at school all day today, and plugged it in cradle just now. I can't repeat the error, so I have no idea how, but it's working just fine. So....solution was to do nothing and let it go away, haha.
Ipaq Hx 2190 Wm6 Pdaviet Installed Ok
I Have Installed Wm6 Pdaviet Rom On My Hx2190 And All Worked Faster And Better.
No Problems To Install From Hp Rom 1.00.01h, Just Update In Pre-bootloader Mode In Windows Xp Sp2 Os. After Flashing No Need To Make Hard Reset, The System Starts Normaly.No Problems It Batery.
-put device into WHITE bootloader mode and again run the 1.0h rom setup. When you arrive at the screen that asks "update" or "cancel",
1. rename the wm5.xxx.nbf original from HP to wm5.xxx.nbf.old
2. rename the new wm6.xx.nbf from the 4pda.rar/pdaviet file to whatever your wm5-wm5.xxxx.nbf.
3.Flashing begin wait until finish. AC power must be conect. voila!!!
Normal Bootloader Mode:
contacts + mail + reset -let go and press calendar to activate
White Screen Bootloader Mode:
contacts + itask + reset -let go and press calendar to activate
Format P.S. (hold down until activated)(screen will say formating p.s. when activated):
contacts + messaging + power + reset
OR (I had to use this to format the p.s. after the PDAVIET rom upgrade)
calender + power + messaging + reset, release reset - release all
*ROM 4pda.ru
http://4pda.ru/forum/index.php?showtopic=52176 (site)
http://rapidshare.com/files/53282580/WM06.rar.html (rom)
*ROM Pdaviet (Better then 4pda)
http://pdaviet.net/showthread.php?t=13245 (site)
1/2 http://tom-love.net/ROM/HP/WM6.0_5.0...2000.part1.rar (rom)
2/2 http://rapidshare.com/files/60450793...part2.rar.html (rom)
Great Job. Thanks From Portugal.

LG KS20 black screen

Hi,
this afternoon i was trying to flash the ROM of my LG KS20 when i read the combination to enter in the engineering menù. So i looked a bit through the different menus until i click on "Backlight On-Off" option in the "LCD Test" menu.
At this point, the screen on my LG turned off and now i can see that phone still working but the screen remains always black. For example if I click the power button on the right of PDA, the 2 button turn their light on but the screen remains black.The same is when i push the button of photograph machine...if I wait a few second and push again the button the PDA take a photograph because the flash work and i can hear the sound of shutter.
I try to hard reset the PDA, but all remains the same....what can I do???
Please help me
Thans a lot
Maybe you could try to install a software called "My Mobiler" (http://www.mymobiler.com - it's freeware). With this software you could access your KS20 through your PC and try to revert the settings in the LCD Menu?
thanks a lot....last night I found MyMobiler searching somethings for view the device screen on my desktop. After I installed it on my PDA (with some little problem to give the ok for the installation on PDA), I can see the device desktop and so I do the same procedure to restore the backlight.
So now all works fine.
Thanks
Have the same problem
but i not lucky... can't press ok on the black screen, can you publish screen with instalation on PDA to try locate the OK??
really thanks
On your screen, you should see the standard view of the installation process.
So, when you launch the install from your pc, you have to immagine the screen of the acknoledge of the install. try to push in the left corner at the bottom a couple of time, then you shoud see the today screen on your pc.
Same problem
I have the same problem, but I need to enter my pin, but I'm not able to enter it because I can't see anything...
And I change the USB settings in the engineering menu so I cannot connect with ActiveSync :S
Any idea?
Thanks a lot.

Screenlock invisible after upgrading to lollipop

Hello
I tried updating using Sony PC Companion application after it had finished, i turned it on and waited for the upgrading processes it took a long time and my phone's back became hot *really hot* then after it had finished upgrading it stuck with a blank screen and didn't take me to the home screen i can go to the camera if i pressed the capturing button , i can turn it off/restart it take screenshots or record the screen but i cannot go to the home screen and access other applications i can't even go to settings or notifications all i can see is the notifications and the back button i can't click at notifications and i cannot enter a pattern/password this so hopeless
sometimes it shows me the message * InitialBootSetup isn't responding * but even though nothing changes it stays at the same way
infos you might need
My phone is not rooted , it doesn't have a sim card/sd card, usb debugging is disabled and it was locked with pattern lock before upgrading
i tried using android device manager changed the password but still no big changes just got the ability to access emergency calls
the worse thing is that i didn't back it up before upgrading :crying:
Hello?
I thought I was alone.
This happened to me when I upgraded my Z1C to Lollipop too. All I did was:
1 Turn the phone off.
2 Connect it to the computer.
3 Open Sony PC Companion
4 Go to Support Zone (That's the first tiled option in PC companion).
5 Select Phone/Tablet Software Update.
It will go through the same process it went through at the initial stages of the update process. When it asks you to unplug the phone, go right ahead and you're good from there.
May flashing System (Lollipop) again will fix that!?
I wasn't able to re-update it because it requires me to unlock the phone
and i couldn't do so because i wasn't able to see the pattern lock to unlock it
sadly i had to repair my phone through the repair option in Sony PC Companion app
this resulted in overwriting everything and losing my data ..
I'm having the same problem (new, un-rooted phone) but any time I try to repair my phone using PC Companion I get an error message about a failure in sony update engine (error number 302). tried 3 different computers and running as an administrator with w7 or xp compatibility mode but i got the same error every time.
what can I do?
EDIT:
flashing a new firmware using flashtool solved the problem.

Note 7 does not boot anymore after Samsung update without warning

hey all,
maybe someone can help make my note 7 boot again
after getting an update yesterday on my note 7 i saw it in message 15 sec to go even i unchecked automatic update it was updated automaticly,
it showed up some sec with that note7 white screen and hangs now with that message in left upper corner in the image here (Kernel Rev. Check Fail Device:1 Binary:0)
tryed all button combination but no success no way to power it down also . Today the display was total black if i charge it the message only appers again
hope ther is away to get it back to get my data
thankyou
Have you tied holding Power key and the Volume down key simultaneously for more than 7 seconds? It should make a restart or power off. When phone restarts try pressing HOME + VOLUME DOWN + POWER you should boot to download mode, then try flashing latest firmware with Odin or use Smart Switch. IF you can't get to dl mode I don't know any other way to fix the phone
thy mk)
i tried Volume down key simultaneously for more than 7 second then the red message dissapears for some seconds and comes back
in that download screen i can go btw it is not rooted or smth just original phone
but that mean to loose all Data at the end? and maybe garanty?
jojo34 said:
thy mk)
i tried Volume down key simultaneously for more than 7 second then the red message dissapears for some seconds and comes back
in that download screen i can go btw it is not rooted or smth just original phone
but that mean to loose all Data at the end? and maybe garanty?
Click to expand...
Click to collapse
Try smart switch program on you PC. And use emergency firmware restore. But it will wipe you data i believe.
thy very much mk
i managed to set it back fresh )
lost data but can be sure it is emty now so i can send it back )
next time i do faster backup i promise hehe

Update firmware with NetOdin

Hi all,
I noticed that the BSA4 update has been released everywhere except Australia. I've been able to get my hands on the firmware files but do not know how to get the watch to connect with NetOdin.
Has anyone been able to do this? I've seen videos of it for the Gear S2 and Gear S3 but there is no way to "restart" the device, only "power off".
Any help would be greatly appreciated.
cheers,
Hieu.
Actually nevermind I managed to get it working on my own..
Nice going!
so where you get firmware....and how did you do it...give us a rundown
Hi, have you succeeded? Can you give us a tutorial so that everyone can enjoy it?
Sure guys. Will put something together later today after work. Getting my hands on the firmware took a bit of searching but managed to find it on a Russian forum.
Will provide a run down of the process and links to the firmware (note: only know where to download the firmware for the 46mm and 42mm Bluetooth version, not the LTE).
0. This process will factory reset your Watch, so make sure you've backed up everything you need!
1. Hold down the Home button for 6-10 seconds until the message " Rebooting ... "
2. Quickly press Home three times until the Reboot Menu appears. (The menu is available for about 10 seconds, after which the clock goes back to "Rebooting ...")
3. The menu selection is made by long holding Home button. To go into Download (wireless mode) press the home button until "Download (Wireless)" is highlighted, then hold down the Home button.
4. Download mode will load in WPS mode. Press Home twice to change the mode to the AP.
5. Connect to the access point that appears (for example, SM-R800-a2a5) (ODIN for some reason does not see the device if several networks are connected.)
6. Run NetOdin3 and then set the firmware files for BL, AP and CSC, then click Start (Copying/flashing of firmware takes about 20 minutes).
7. After the files are downloaded, the Watch will reboot. Again, hold Home and highlight & select Recovery in the Reboot menu.
8. The "Setting Up" screen and "Resetting" screen should appear and after that the Watch will reboot and boot as usual.
N.B. It is advisable to check whether you have disabled the function "find my watch" or make sure you remember the password to your Samsung Account
Files can be found here for R800 and R810 (46mm and 42mm Bluetooth / Non-LTE G.Watches) and NetOdin3 for Tizen:
R800XXU1BSA4
R810XXU1BSA4
NetOdin3 for Tizen
thanks a lot........but watch not showing in netodin as in the showing connection on the pc.....how do i connect
edwardob said:
thanks a lot........but watch not showing in netodin as in the showing connection on the pc.....how do i connect
Click to expand...
Click to collapse
Did you connect to the access point of your watch via the wifi settings on your PC?
Huey85 said:
Did you connect to the access point of your watch via the wifi settings on your PC?
Click to expand...
Click to collapse
it did eventually thanks a lot..
by the way where you pick up those files
edwardob said:
it did eventually thanks a lot..
by the way where you pick up those files
Click to expand...
Click to collapse
from 4pda - it's a russian website that discusses smartphones, smartwatches and so forth.
keep an eye on it for future purposes.
Huey85 said:
0. This process will factory reset your Watch, so make sure you've backed up everything you need!
1. Hold down the Home button for 6-10 seconds until the message " Rebooting ... "
2. Quickly press Home three times until the Reboot Menu appears. (The menu is available for about 10 seconds, after which the clock goes back to "Rebooting ...")
3. The menu selection is made by long holding Home button. To go into Download (wireless mode) press the home button until "Download (Wireless)" is highlighted, then hold down the Home button.
4. Download mode will load in WPS mode. Press Home twice to change the mode to the AP.
5. Connect to the access point that appears (for example, SM-R800-a2a5) (ODIN for some reason does not see the device if several networks are connected.)
6. Run NetOdin3 and then set the firmware files for BL, AP and CSC, then click Start (Copying/flashing of firmware takes about 20 minutes).
7. After the files are downloaded, the Watch will reboot. Again, hold Home and highlight & select Recovery in the Reboot menu.
8. The "Setting Up" screen and "Resetting" screen should appear and after that the Watch will reboot and boot as usual.
N.B. It is advisable to check whether you have disabled the function "find my watch" or make sure you remember the password to your Samsung Account
Files can be found here for R800 and R810 (46mm and 42mm Bluetooth / Non-LTE G.Watches) and NetOdin3 for Tizen:
R800XXU1BSA4
R810XXU1BSA4
NetOdin3 for Tizen
Click to expand...
Click to collapse
Thanks, I have a problem, when I connect my computer to my watch, my watch directly says "connection fail: Connection timed out (110).
Do you have any suggestions please? the computer still connected to the watch
fabiere said:
Thanks, I have a problem, when I connect my computer to my watch, my watch directly says "connection fail: Connection timed out (110).
Do you have any suggestions please? the computer still connected to the watch
Click to expand...
Click to collapse
just start again.....it timed out which means maybe you where to slow
fabiere said:
Thanks, I have a problem, when I connect my computer to my watch, my watch directly says "connection fail: Connection timed out (110).
Do you have any suggestions please? the computer still connected to the watch
Click to expand...
Click to collapse
Restart both devices and try again is what I'd recommend. And disconnect from your home wifi that you're usually connected to on your PC first before trying to connect to your Watch's access point.
edwardob said:
just start again.....it timed out which means maybe you where to slow
Click to expand...
Click to collapse
It says that 5 seconds after being connected to network, via WPS or AP it's the same... 5 seconds ? Too slow ?...
Huey85 said:
Restart both devices and try again is what I'd recommend. And disconnect from your home wifi that you're usually connected to on your PC first before trying to connect to your Watch's access point.
Click to expand...
Click to collapse
I've deleted all data about my home wifi in my computer, and it's the same problem, and if i connect via wps, it is exactly the same, any developper option to activate before ? like Android devices ?
Here is netOdin since Gear S2.. S3...
With infos + Videos...
https://forum.xda-developers.com/showpost.php?p=73503787&postcount=150
Maybe it helps for better understanding...
Best Regards
fabiere said:
It says that 5 seconds after being connected to network, via WPS or AP it's the same... 5 seconds ? Too slow ?...
I've deleted all data about my home wifi in my computer, and it's the same problem, and if i connect via wps, it is exactly the same, any developper option to activate before ? like Android devices ?
Click to expand...
Click to collapse
I find connecting via AP is more stable than WPS. Give that a try.
Huey85 said:
I find connecting via AP is more stable than WPS. Give that a try.
Click to expand...
Click to collapse
Tested via AP, error after 5 seconds
Tested via WPS, error after 5 seconds
That is the problem, nothing to activate like developper options or other ?
fabiere said:
Tested via AP, error after 5 seconds
Tested via WPS, error after 5 seconds
That is the problem, nothing to activate like developper options or other ?
Click to expand...
Click to collapse
Nothing. You don't need to activate anything in developer menu. Have you tried on another computer?
My connection is always stable on AP connection mode.
Huey85 said:
Nothing. You don't need to activate anything in developer menu. Have you tried on another computer?
My connection is always stable on AP connection mode.
Click to expand...
Click to collapse
Don't have another computer, that's why i've tested via WPS
Will test later to fectory reset, maybe an internal bug

Categories

Resources