Related
My Pda 2k device i tryed to upgrade it from 2003 SE to 2k5 after pressing update the device restarted gived me a gray screen and typed on it seril and at the buttom v2.02 now i cant open the device each time i reset or heard rest this is the only screen appears to me i cant even connect to activsync please i need your help what to do to get my device back, this error message i recived (usb device not recognized aslo active sync didnt recognize it)
i need to add a point the device is not working on the USP connection as it have a problem only serial port to connect with the pc
i'm so new here please help me
not to worry.. you can perform a hard reset of your 2k3 version "power+reset" to get you back to at least a working device.. I have been through this and have had this happen to me as well.. try entering bootloader again "power+record+reset" and dock it fairly quickly and it should change to USB on the screen and PC recognize it... also for anyone reading this.. I would highly recommend plugging your cradle into a 5v power supply as I can only imagine most of the bricked BAs are probably due to a computer freezing and/or the PC shutting down power to the USB port only for a fraction of a second and hosing the flash up.
THx Man i will try i hop this will work :lol:
I tried to upgrade my rom but the process crashed. The utility mtty doesn't work because when I connect the universal, boatloader mode by the cable, to the pc, it says "USB not recognized" (sometimes when I connect the computer is frozen till I disconnect the cable of the universal)
Please, I tried to have some solutions in the forum but all the posts indicates is needed previously the usb connection.
Do you know if should be possible to run the flash of the rom in other way, for example using a serial cable connected into the miniusb of the universal, because the boatloader screen says "Serie, v.1.01"
I apprecite what you can say please, I'm really in a hole.
Try this...
Try taking out the battery for a few minutes (10-30mins) and reboot your PC then repeat upgrade process. Hope that helps. Good luck!!!
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
Click to expand...
Click to collapse
In my case it still happening in other computers. Conclussion: some piece of the software in the universal has been lost. The screen shows "Serial" that means on some way that is opened to comunication but not USB.
My questions are:
- should be possible to put some starting software in SD and do the universal boot on it.
- do you know how to connect to the computer COM! port from the usb miniport of the Universal.
I appreciate, I was not planning to replace now the Universal...
beginner said:
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
Now works.... I still thinking windows is so stupid software made for distroy our mind ....
Solved after install drivers for a converter usb -rs232 ( I was looking for the way to connect from rs232 the universal)
I'm happy again and I promise don't try to change rom again (at least for a while)
If some person is interested in what brand of software/hardware I installed, send me a mail...
Thanks hearing me ...
Click to expand...
Click to collapse
Click to expand...
Click to collapse
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
zedino said:
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
Click to expand...
Click to collapse
I want to say that is running after doing some things and obviously some of it solved my problems. I made:
- unistall last version of activesync and go back to version 4.0
- delete all the applications using ports usb.
due the connection still not running (windows message: device not recognized) and because in the screen of universal I saw: "COMM1" I tried to connect from computer port rs232. By that I purchased some special cable, name: hama brand, rs232 serial, 9 pin - usb.
As you can imagine all the steps I followed were followed by the typical restart of windows. In this sense is important to say that the universal, after connect, need to do a soft reset each time (again windows....)
Other comment is that I unmark the option to connect by usb in activesync and mark the connection by com1.
and after all was done, connecting by usb the unniversal, kill wcescomm, windows said "NEw usb device, sync device". I started mtty and now appears the USB option, great! same time the screen in universal changed from comm1 to usb, more great....
and that's all.
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
zedino said:
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
Click to expand...
Click to collapse
I think my english wording was not fine. I mean I solved my problem after install the sofware -drivers- of the rs232 connector, but connecting to the universal by usb as on standard way I was syncronizing previous the crack with activesync.
OK, where to get this driver?
thanx
?????????? NOTHING ?????????????
zedino said:
OK, where to get this driver?
thanx
Click to expand...
Click to collapse
Try here.
http://www.hama.de/portal/type*3/action*1026/searchMode*1/q*039703
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
shrubbery said:
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
Click to expand...
Click to collapse
not works, probably is this device lost forever, i have restarted device and PC almost hundred times, still the same result, uni stuck in Bootloader screen top of page "Serial" bottom of page "v1.00"
nothing changed, even if i connect to USB port
if someone have some solution to this s*it pls let me know
thanx
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
no, my problem persist, hundred times i tried to recover friends device using upgrade by original shipped ROM but the device is not recognized by system so there is allways connection error, so this kind of reliving this UNI is not usable
anyway, thanx for raply and suggestion
ZeD
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
If you're stuck in bootloader mode only, visit www.buzzdev.netand look for ExitBootloader utility written by the great Buzz. Just follow his instructions or scroll thru' Universal's forum here and there for problems relating to "stuck in bootloader"
hope this helps
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
i had the same problem with the QTEK of my principal after I upgraded his ROMs.
(after the hard reset, the pocket remained in bootloader mode).
you can solve this problem in a very simple way:
you have to launch the bootloader installation (BL1.01_RUU_UNI_V.1.2.EXE) from the PC (still connected with the PPC through USB) while the PPC is in bootloader mode (on your display you see "USB > Serial 1.01" or something like that).
then you do a SOFT reset and the pocket boot normally.
very simple.
i hope to be helpful to someone.
zedino said:
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
Click to expand...
Click to collapse
I had some problem. After uninstall all usb applications in the pc and install the software for cable usb -rs 232, doing some softreset in the pda connected, it turned the screen message "Com" by "Usb"
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Try this it shld work
hdubli said:
This is based on my experience with two UNis..one Exec and other JASJAR..both had same problem...this is how I solved :
-Put yr device in bootloader Mode
-Disable USB in Active Sync
-Now connect woth USB cable and open mtty utility
-Select the "WESUSB... " port
-You shall see a blank white screen..press Enter to get "USB>"
-Then type ( as BUzz has informed) set 14 0
(here I wud like to inform that after doing the above I did not get success so I typed set 14 10,then set 14 9 for two three times)
-Then I ran the ROM Upgrade directly(After enbabling the USB)
-I then followed the procedure as informed on the COngratulations Screen that is hold the two "-" buttons and soft reset and then pressed 0
-I got them back to normal..
I hope this helps to all my friends...Pls feel free..pls do not trouble our Buzz..he might be busy in inventing something more to our devices
Click to expand...
Click to collapse
Guru Meditation said:
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Just noticed your user name, I was a big Amiga fan a few years back, still fire up Amiga forever occasionally on my PC when I feel the need.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Click to expand...
Click to collapse
Try it with a different USB cable or in a different USB port (don't go through a hub and if you've been using a laptop then try it on a desktop PC since some laptops have hubs built into them). If that doesn't work then you're out of luck as your Universal isn't detecting that you've connected to your PC and its time to send it in for repair.
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
i am stuck on the same problem and wondering the forum for almost 3 days now with no luck.... please help my device is in boot loader mood but not turning the serial to USB ......... please HELP.......
solution
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Please follow the steps:
1. Plug in ur usb cable in bootloader mode while it is showing 'serial' and version 'x.xx'.
2. Soft reset by pressing Backlight+power+reset pin WHILE KEEPING THE USB CABLE CONNECTED
3. your phone will now reboot into 'usb' mode. Don't remove the usb cable yet.
4. Remove the Memory card while keeping the usb cable still connected and VOILA,your pc starts recognising your phone as Microsoft usb sync.
5. Do whatever you want to do now (upgrade)
Hope it solves the problem now.
Press thanks if it does.
Something else to try
Having had a few issues with my G3 Uni, I've been through my fare share of Uni bootloader issues. When I find that I can't get the 'serial' to go to 'USB', I normally find it's because I haven't taken the memory card or the SIM card out (usually the memory card).
Make sure your memory card is out, then try to enter the bootloader and see if this cures it. If it does, then use mtty and the command 'set 14 0'
This tells it to reboot on reset. if you were to use 'set 14 1' it would go back to the bootloader on reset.
my Htc hd2 t-mobile won't recognize usb on boot-loader mode
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
kaleb2954 said:
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
Click to expand...
Click to collapse
you have the wrong forum friends! This Htc Universal section
to update Android on HTC HD2, you can use the Clock Work Mod Recovery !! for more details should refer to this thread http://forum.xda-developers.com/showthread.php?t=1021837
I-MATE JASJAR hung
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
bechir2013 said:
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
the first point...
A lot easier than to root this device
Hi, my univversal is dead in bootloader at serial mode and when I connect it to my PC with usb cable it recognize it as an Unknown devices and my phone still stand in serial mode!
I was trried all the method I found like:
I went to device manager of my PC an re-install my usb--didnt work
shut down usb and active synch (with task manager) and ry mtty program-- dident work
I change my usb cable and change te mini usb gate of my phone!-- didnt work
Plz help me!!!!!!!!
god_love_power said:
Hi, my univversal is dead in bootloader at serial mode and when I connect it to my PC with usb cable it recognize it as an Unknown devices and my phone still stand in serial mode!
I was trried all the method I found like:
I went to device manager of my PC an re-install my usb--didnt work
shut down usb and active synch (with task manager) and ry mtty program-- dident work
I change my usb cable and change te mini usb gate of my phone!-- didnt work
Plz help me!!!!!!!!
Click to expand...
Click to collapse
Hi welcome to the forum.... try following
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
(try method 2)
and try to change the computer usb ports...try different usb ports of the computer and try flashing to tomals 8.5 or 8.7 ...
Cheers
Rajiv
Thank you rajivshahi for your answer and attention.
I had try all the methods that I find in hole of internet!!
also I tried your suggstted method. I was connect my phone with ans without SIM and memory to each USB port of my (and another) PCs, I changed my USB cable for several times, I also tried Uni_bootloader program and MTTY but they didn't work (because there is no USB connetion with my UNI and my PC)
I just keep crying!!!!!!
Have you tested doing Doc format?
Hope it helps,
If the device is not recognised by PC at the same time as Serial not changing to USB, I would think your USB port is no longer attached as it should and can cause the problem you described. From time to time USB port might still feel and look secure on mainboard, it will even charge the device, however, when it comes to AS and USB connection to PC, it will not connect properly.
That, or your PC USB or motherboard are malfunctioning. Try other USB devices in the same ports.
My PC's USB ports are work properly because as you told enigma1nz, I had test them with another devices
For the DOC format method: there is no USB port for connecting with MTTY!
Soooooo amazing!
(thanks for all your answers)
So, it means there is no way for me
hey,
have you disabled (unckeck) USB connection for ActiveSync/WMDC at PC?
do it now or USB port will not be available for mtty.
also please make sure that you installed XP sync driver under vista incase you're trying from vista.
follow the same -
1. unckeck USB connection for as/wmdc at pc
2. reset the device by pressing reset button
3. set bl mode (if not there already)
4. connect usb cable
5. start mtty ...
Hi Tomal, first I have to say: Thank you for your amazing roms. they are so fast, nice and stable. I'm one of the biiiig fan of your roms.
seconed: yes I was disabled the USB connection and also kill ir from task manager. but my Uni is still deeaaaaaaad
somehow I have a feeling that something is wrong with the usb port in device. may be connection is broken or something...
Hi everyone,
finally I had to send my Universal to doctor! , he says that I can load your device from SD card, and boot up it, (flashing card)
!!
I was wondered! what is flashing card! (load from SD card without any PC!)
Do any one have some information about this method!!!!
enigma1nz said:
If the device is not recognised by PC at the same time as Serial not changing to USB, I would think your USB port is no longer attached as it should and can cause the problem you described.
Click to expand...
Click to collapse
tomal said:
somehow I have a feeling that something is wrong with the usb port in device. may be connection is broken or something...
Click to expand...
Click to collapse
Yep, it does look like your device's USB being a culprit.
god_love_power said:
Hi everyone,
finally I had to send my Universal to doctor! , he says that I can load your device from SD card, and boot up it, (flashing card)
!!
I was wondered! what is flashing card! (load from SD card without any PC!)
Do any one have some information about this method!!!!
Click to expand...
Click to collapse
I believe this is the thread you are looking for
http://forum.xda-developers.com/showthread.php?t=393370
Thanks a lot enigma1nz, i think that i need but can you (or any one) explane it, step by setp for me PLEASEE !:
1. Download the tool and unrar somewhere in your pc.
2. Decode the rom image (nk.nbf) using HTC64 tool and put it (nk.nba) under the "SD_Flash" directory.
3. Run the "SDFlash_G3.cmd" and follow instruction on the screen.
SD_Flash?????
Decode the rom image (nk.nbf)???????!!
this method is for 3G, my device is 4G
This is the solution
god_love_power said:
this method is for 3G, my device is 4G
Click to expand...
Click to collapse
my dear frnd few days back i was also suffered from that problem...
And problem was with mini usb in universal.
it was disconnected with there tracks from inside.
So just open ur g4 device and resold mini usb.
trust me this is the problem.
Thanks yuvraj, how can I do it? Is there any manual for it?
can you help
You can find the manual in the Wiki, just do a search
I could'nt creat golden disk (flash from sd) cos that is for G3 devices, I just think that can we install another OS like linux on SD that is boot himself up?!
or i just have to change my universal mainboard!!!!?
Finally I beleve that my Uni is dead and I have to say goodbye to it
I'm going to buy HTC Advantage X7510, but there is one question:
Can I upgrade its WM 6.1 to 6.5 ?
Can any one help with this?
My Diamond has developed the short battery life/over heating problem, along with the USB connection having failed.
So I put the ROM back to the standard T-Mobile one via Wi-Fi to return for warranty repair.
However, I forgot to change the SPL back, so they are refusing to sort it.
My next thought was to get HTC to repair it, but thought I'd best stick the T-Mobile SPL back for good measure.
But the update failed (tried more than once) and I'm stuck on the bootloader with "Upgrade ROM Code Error, Please Try Again" and only "Serial" showing as a connection option, no USB (yes with a cable connected to a PC).
Is there anyway at all I can get to Internal Storage to try another update?
Thank you.
hello,
i had a similar problem. after flashin a buggy rom the diamond made a reboot and hang at the initializing screen. i tried a garanty repait but htc saw the spl and denys my garanty. so i started to ask google for help.
i got the device in bootloader mode, showing "serial". but i got no active sync connection. but after any tries i got the firmware update tool into "usb" mode and was able to flash. now my diamond is still alive.
maybe you have to play a bit to get it workin..
wish you luck..!
Try with another usb cable, computer. And explane me this
So I put the ROM back to the standard T-Mobile one via Wi-Fi to return for warranty repair.
Click to expand...
Click to collapse
How you can flash rom via wi-fi :S
I've tried 3 PCs and as many USB cables, it appears to be a hardware fault tied in with the overheating...
And sorry, I didn't explain very well regarding the Wi-Fi.
I simply used that as a file transfer method as I couldn't connect via USB. Saved the SPL as diamimg.nbh and did the Vol- + Back reset.
Understand now. Maybe usb connector is damaged by overheating or something else. I can't help you anything because diamond don't have microsd card - can't flash via microsd method