Related
Ok this is the situation:
yesterday my phone started malfunctioning, my screen was flickering going to white then back to color, when i turned it off using the power button it dies and needs a reset to turn back on. i contacted imate and they said to reinstall the ROM i started to do so but it kinda got stuck and said there was a different language rom (even though it was what i put on it a month ago) anyway i disconnected it and now i am stuck with the bootloader screen (says serial v2.06 and when i connect it to the hub it changes to USB v2.06) i canceled the active syncs usb connection but when i tried to reinstall the rom it just gets stuck and gives me an error 201 cant get data from device, also when this happens the device gets stuck on USB even if i take it off the hub (it is supposed to change back to serial) and if i dont reset it windows says the device malfunctioned and doesnt communicate with it. Please help
Try using the usb lead direct to the usb port, sometimes the hub will make it fail.
I cant cause this imate just came with the hub and it specifically states that it has to be connected to the hub AND the hub has to be connected to the power supply
please help
it is fixable
hi my friend, i had the same problem with my t mobile mda 3. it is fixable . the problem simly is that your rom is erased and you need to get another one by upgrading it. that's all and i recommend using cradle if you have one. i upgraded mine to 1.40 i mate rom.
tell me if you need more help,
next time back up your phone beforehand
I tried to upgrade my rom but the process crashed. The utility mtty doesn't work because when I connect the universal, boatloader mode by the cable, to the pc, it says "USB not recognized" (sometimes when I connect the computer is frozen till I disconnect the cable of the universal)
Please, I tried to have some solutions in the forum but all the posts indicates is needed previously the usb connection.
Do you know if should be possible to run the flash of the rom in other way, for example using a serial cable connected into the miniusb of the universal, because the boatloader screen says "Serie, v.1.01"
I apprecite what you can say please, I'm really in a hole.
Try this...
Try taking out the battery for a few minutes (10-30mins) and reboot your PC then repeat upgrade process. Hope that helps. Good luck!!!
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
Click to expand...
Click to collapse
In my case it still happening in other computers. Conclussion: some piece of the software in the universal has been lost. The screen shows "Serial" that means on some way that is opened to comunication but not USB.
My questions are:
- should be possible to put some starting software in SD and do the universal boot on it.
- do you know how to connect to the computer COM! port from the usb miniport of the Universal.
I appreciate, I was not planning to replace now the Universal...
beginner said:
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
Now works.... I still thinking windows is so stupid software made for distroy our mind ....
Solved after install drivers for a converter usb -rs232 ( I was looking for the way to connect from rs232 the universal)
I'm happy again and I promise don't try to change rom again (at least for a while)
If some person is interested in what brand of software/hardware I installed, send me a mail...
Thanks hearing me ...
Click to expand...
Click to collapse
Click to expand...
Click to collapse
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
zedino said:
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
Click to expand...
Click to collapse
I want to say that is running after doing some things and obviously some of it solved my problems. I made:
- unistall last version of activesync and go back to version 4.0
- delete all the applications using ports usb.
due the connection still not running (windows message: device not recognized) and because in the screen of universal I saw: "COMM1" I tried to connect from computer port rs232. By that I purchased some special cable, name: hama brand, rs232 serial, 9 pin - usb.
As you can imagine all the steps I followed were followed by the typical restart of windows. In this sense is important to say that the universal, after connect, need to do a soft reset each time (again windows....)
Other comment is that I unmark the option to connect by usb in activesync and mark the connection by com1.
and after all was done, connecting by usb the unniversal, kill wcescomm, windows said "NEw usb device, sync device". I started mtty and now appears the USB option, great! same time the screen in universal changed from comm1 to usb, more great....
and that's all.
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
zedino said:
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
Click to expand...
Click to collapse
I think my english wording was not fine. I mean I solved my problem after install the sofware -drivers- of the rs232 connector, but connecting to the universal by usb as on standard way I was syncronizing previous the crack with activesync.
OK, where to get this driver?
thanx
?????????? NOTHING ?????????????
zedino said:
OK, where to get this driver?
thanx
Click to expand...
Click to collapse
Try here.
http://www.hama.de/portal/type*3/action*1026/searchMode*1/q*039703
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
shrubbery said:
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
Click to expand...
Click to collapse
not works, probably is this device lost forever, i have restarted device and PC almost hundred times, still the same result, uni stuck in Bootloader screen top of page "Serial" bottom of page "v1.00"
nothing changed, even if i connect to USB port
if someone have some solution to this s*it pls let me know
thanx
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
no, my problem persist, hundred times i tried to recover friends device using upgrade by original shipped ROM but the device is not recognized by system so there is allways connection error, so this kind of reliving this UNI is not usable
anyway, thanx for raply and suggestion
ZeD
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
If you're stuck in bootloader mode only, visit www.buzzdev.netand look for ExitBootloader utility written by the great Buzz. Just follow his instructions or scroll thru' Universal's forum here and there for problems relating to "stuck in bootloader"
hope this helps
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
i had the same problem with the QTEK of my principal after I upgraded his ROMs.
(after the hard reset, the pocket remained in bootloader mode).
you can solve this problem in a very simple way:
you have to launch the bootloader installation (BL1.01_RUU_UNI_V.1.2.EXE) from the PC (still connected with the PPC through USB) while the PPC is in bootloader mode (on your display you see "USB > Serial 1.01" or something like that).
then you do a SOFT reset and the pocket boot normally.
very simple.
i hope to be helpful to someone.
zedino said:
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
Click to expand...
Click to collapse
I had some problem. After uninstall all usb applications in the pc and install the software for cable usb -rs 232, doing some softreset in the pda connected, it turned the screen message "Com" by "Usb"
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Try this it shld work
hdubli said:
This is based on my experience with two UNis..one Exec and other JASJAR..both had same problem...this is how I solved :
-Put yr device in bootloader Mode
-Disable USB in Active Sync
-Now connect woth USB cable and open mtty utility
-Select the "WESUSB... " port
-You shall see a blank white screen..press Enter to get "USB>"
-Then type ( as BUzz has informed) set 14 0
(here I wud like to inform that after doing the above I did not get success so I typed set 14 10,then set 14 9 for two three times)
-Then I ran the ROM Upgrade directly(After enbabling the USB)
-I then followed the procedure as informed on the COngratulations Screen that is hold the two "-" buttons and soft reset and then pressed 0
-I got them back to normal..
I hope this helps to all my friends...Pls feel free..pls do not trouble our Buzz..he might be busy in inventing something more to our devices
Click to expand...
Click to collapse
Guru Meditation said:
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Just noticed your user name, I was a big Amiga fan a few years back, still fire up Amiga forever occasionally on my PC when I feel the need.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Click to expand...
Click to collapse
Try it with a different USB cable or in a different USB port (don't go through a hub and if you've been using a laptop then try it on a desktop PC since some laptops have hubs built into them). If that doesn't work then you're out of luck as your Universal isn't detecting that you've connected to your PC and its time to send it in for repair.
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
i am stuck on the same problem and wondering the forum for almost 3 days now with no luck.... please help my device is in boot loader mood but not turning the serial to USB ......... please HELP.......
solution
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Please follow the steps:
1. Plug in ur usb cable in bootloader mode while it is showing 'serial' and version 'x.xx'.
2. Soft reset by pressing Backlight+power+reset pin WHILE KEEPING THE USB CABLE CONNECTED
3. your phone will now reboot into 'usb' mode. Don't remove the usb cable yet.
4. Remove the Memory card while keeping the usb cable still connected and VOILA,your pc starts recognising your phone as Microsoft usb sync.
5. Do whatever you want to do now (upgrade)
Hope it solves the problem now.
Press thanks if it does.
Something else to try
Having had a few issues with my G3 Uni, I've been through my fare share of Uni bootloader issues. When I find that I can't get the 'serial' to go to 'USB', I normally find it's because I haven't taken the memory card or the SIM card out (usually the memory card).
Make sure your memory card is out, then try to enter the bootloader and see if this cures it. If it does, then use mtty and the command 'set 14 0'
This tells it to reboot on reset. if you were to use 'set 14 1' it would go back to the bootloader on reset.
my Htc hd2 t-mobile won't recognize usb on boot-loader mode
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
kaleb2954 said:
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
Click to expand...
Click to collapse
you have the wrong forum friends! This Htc Universal section
to update Android on HTC HD2, you can use the Clock Work Mod Recovery !! for more details should refer to this thread http://forum.xda-developers.com/showthread.php?t=1021837
I-MATE JASJAR hung
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
bechir2013 said:
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
the first point...
A lot easier than to root this device
Title explains most of the problem, my phone wont connect to my pc using active sync. If I plug it in, the device shows it is charging, but I cant get anything else, no disk drive, no active sync, no internet sharing. I thought at first it was a USB problem on the phone, but it charges fine on all chargers and even charges on the PC.
so question is, what can I do to make it work and I need to change the spl to .82 (tmobile stock) so i can do a warranty exchange. Any one know if I can flash SPL from sd card like I can on Android devices.
Currently I have spl .79 , the stock winmo 6.5 tmobile rom and latest tmobile radio.
palosjr said:
Title explains most of the problem, my phone wont connect to my pc using active sync. If I plug it in, the device shows it is charging, but I cant get anything else, no disk drive, no active sync, no internet sharing. I thought at first it was a USB problem on the phone, but it charges fine on all chargers and even charges on the PC.
so question is, what can I do to make it work and I need to change the spl to .82 (tmobile stock) so i can do a warranty exchange. Any one know if I can flash SPL from sd card like I can on Android devices.
Currently I have spl .79 , the stock winmo 6.5 tmobile rom and latest tmobile radio.
Click to expand...
Click to collapse
Before you go to extremes, have you you tried changing the USB to PC settings? Try this:
Uncheck the box that says "Enable faster data syncronization", unplug, replug. No dice?
bug666 said:
Before you go to extremes, have you you tried changing the USB to PC settings? Try this:
Uncheck the box that says "Enable faster data syncronization", unplug, replug. No dice?
Click to expand...
Click to collapse
yea, no luck. Ive done a system restore on my PC and all. My PC has been freaking out lately and I am in safe mode right as a matter of fact removing some junk and what not. It will detect the phone, but then when it is installing drivers for it, it ALWAYS fails. no matter what USB port. I have even tried other computers and no luck with that either. I am pretty sure its the USB port on the phone.
so it leads me to my question, can i flash to the .82 SPL from my sdcard or am i pretty much just SOL
Ironic......
I have a similiar but different problem.
I need to do a warranty exchange because my touch screen has stopped working. Unfortunately the last time I used my phone I used internet sharing so now whenever I attach via usb it comes up as internet sharing and it will not let me change it to Activesync. I need to put the stock rom back on the phone so I can send it back. I'm stumped......
phoneoftheday said:
I have a similiar but different problem.
I need to do a warranty exchange because my touch screen has stopped working. Unfortunately the last time I used my phone I used internet sharing so now whenever I attach via usb it comes up as internet sharing and it will not let me change it to Activesync. I need to put the stock rom back on the phone so I can send it back. I'm stumped......
Click to expand...
Click to collapse
All you need to do is boot into the bootloader (turn off the device, then press power while holding [Volume down]), plug the device into your computer, and flash as usual. Just make sure you put back the appropriate stock SPL (which can be found in the HardSPL thread) after you flash back to the stock ROM, if the stock ROM you're flashing doesn't include it. You can verify that you have a stock SPL by looking at the bootloader, since a stock SPL will not say OliNex anywhere.
palosjr: AFAIK, there's no way to flash an SPL via SD card on the Rhodium, or most HTC Windows Mobile devices for that matter. I would highly recommend finding another computer, like one at your local library, to flash the SPL with.
DaveTheTytnIIGuy said:
palosjr: AFAIK, there's no way to flash an SPL via SD card on the Rhodium, or most HTC Windows Mobile devices for that matter. I would highly recommend finding another computer, like one at your local library, to flash the SPL with.
Click to expand...
Click to collapse
It wont be detected by any computer. It only charges. For some reason it wont detect as a USB device, it always fails to load the drivers. I am going tomorrow to a DrCellPhone place to have them see what they can do with it, if it is the USB its 25 to get it replaced with a new warranty.
funny, I have exactly the same problem with the same device, everything is working (charge the battery, headphones via mini usb, ...) but I can not sync with my pc. I hoped that I need a special HTC usb cable for that?!
But I assume, that I have this problem due to the fact that I charged the battery with 5V and 2 Ampere ... maybe that has broken one connector?
DaveTheTytnIIGuy said:
All you need to do is boot into the bootloader (turn off the device, then press power while holding [Volume down]), plug the device into your computer, and flash as usual. Just make sure you put back the appropriate stock SPL (which can be found in the HardSPL thread) after you flash back to the stock ROM, if the stock ROM you're flashing doesn't include it. You can verify that you have a stock SPL by looking at the bootloader, since a stock SPL will not say OliNex anywhere.
palosjr: AFAIK, there's no way to flash an SPL via SD card on the Rhodium, or most HTC Windows Mobile devices for that matter. I would highly recommend finding another computer, like one at your local library, to flash the SPL with.
Click to expand...
Click to collapse
Thanks. This worked perfectly!!
Ok, from browsing the forum and the net in general this problem appears all too common. Some definitve advice please??
The scenario-
1/ Sync has been happening with WMDC with no issues since i got it. SUddenly it stopped a month ago.
2/ Phone is still charging.
3/ Have tried several different cables
4/ All settings on phone correct
5/ Have hard reset phone several times
6/ Have uninstalled WMDC several times
Are there any other options??? I want to put the new ROM on but obviously am unable to at the minute. Incidently this inability to syncronise seems to have coincided with a major decline in battery standby time (which hasnt been rectifed even with 2 replacement batteries of different makes).
Are there any definitive answers for this issue??
- Did you try another computer?
- Did you try deleting the usb drivers on your pc?
If you want to flash another rom, you can just go into the bootloader, then plugin your usb cable and flash the same way as you would when using WMDC. Or flash true your sd card
If you go into the bootloader en plugin your usb, you can check if your usb on your phone is still working.
Thanks. Did the first two already. USB isnt recognised from bootloader, so that doesnt sound good.
This phone has an Orange Windows 6.1 ROM. Will i be able to flash the new HTC Rom via micro sd without Hard SPL???
Hardware failure. I guess a new USB connector (or just needs soldering, but this is not recommended) would be required.
I think i have to accept that, and its out of warranty.
Does the genuine HTC ROM need hard spl fashing to my Orange Rom machine from Micro SD??
In bootloader im ending up with a not-allow message.
Is there instruction on forum for hard spl from SD on touch pro 2? Cant seem to find anything via search.
Ok, found the official HTC Orange WM 6.5 upgrade and downloaded.
According to everything ive read, if i simply extract the RUU_signed file and rename RHODIMG.nbh; then place on my FAT32 formated Micro SD root; then put the phone to bootloader: it should work.
It doesnt.
Cany anyone help here or am i doomed to using the original Orange WM 6.1 Rom until i can afford a new phone??