Related
Hello everyone.
I have just bought my Hermes (AT&T 8525) after one year of planing so. It came with WM5. I downloaded some of the ROMSs, radio and bootloaders commented here. I tried reading all the vast infromation in this forum and the wiki, but still having a problem.
THE PROBLEM IS AS FOLLOW:
When I start the flashing process, using HTC_TyTN_WWE_3[1].54.255.3_6275_1.48.00.10_108.exe or RUU_Hermes_CINGULAR_WWE_3.1.57.502.1_6275_1.48.00.00_108
... everything goes well, until the progress bar appears in my PC. When it appears, ActiveSync in my PC closes and my Hermes goes to stand by (the lcd goes off) so I cannot complete the installation process.
The phone works pretty well and I'm really amazed for all its capabilities. But still, I'm stucked with wm5.
Why do you think this happened?
PS: I flashed the radio (1.51.00.10) and bootloader (HARD SPL v7). My ROM version is 2.15.502.3. I use "ActiveStink" to sync my files without problems.
Any advice will be more than welcome!!
I'm no expert but that appears to be normal behaviour!
ActiveSync is only used at the start of the process. After a few files have been transfered, Activesync is closed and a different link is established. If you just leave it for a short while longer, a progress bar should appear on the Hermes too.
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
todd_jg said:
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
Click to expand...
Click to collapse
I'm having the same problem - always have. The message tells me that I'm disconnected and that I should check my USB connect etc. I left that box up there for about 15 minutes. Now I've closed the box and have waited several minutes with no activity. This is pretty aggravating. Thanks for any help.
try turning off your antivirus aplication. thats work for me flashing my tytn to wm6.
I've done everything.... I guess
Hi...
Yes, I consulted the www.mrvanx.org, excellent tutorials.
I flashed without problem the radio and bootloader. The progress bar started to "progress" and everything was fine. The only problem I have is flashing the WM6.
I don't remember where, but I readed that flashing the bootloader "Hard SLP v7" causes my HTC not to accept any Oficial WM6 ROM. The article said that I only had the chance to flash a coocked or modified ROMs. Is this true?
If not... what else can it be? I also closed all my applicacations including the antivirus, goback, disabled the internet connection, the logictec mouse center, etc. and nothing, the same as Chicoh happens to me.
"Error 260: Connection... check the USB cable bla bla bla."
Should I restart in safe mode to do the flashing?
Should I try to install a modified ROM?
Have in mind I've tried three different official ROMs: WWE, Cingular and spanish.
Thanks to all the comunity!!!
Saludos desde México!!
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
liquidsilver said:
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
Click to expand...
Click to collapse
I'm trying that as we speak. I have a good feeling about this. I'm a little concerned that I didn't think of it though. Makes perfect sense - Skip the middle man.
UPDATE: Crap. No luck. Thanks all the same though. I'm not giving up.
What OS are you using, xp or vista? My vista 'top had the same problem wouldnt flash for the longest time and i had to use my xp.
However, it does work now. Not entirely sure why.
Now I had success!!!
Hello my friends.
It seems that the article I readed days ago detailing that after flashing the Hard SPL v7, I could only install a modified ROM, not an official one from HTC or Cingular.
I downloaded Black Satin and installed it without any troubles. The entire process lasted only 3 minutes!!!
I wanted to have an official ROM, don't ask me why, and never tried the "other" ROMs that are actually excellent!!! some apps that were on WM5 are not in WM6, which is kind of sad, but if there's something that I love of WM Smartphones is that I can download and install whatever I want or develop it if it doesn't exist!!!
By the way, I use Windows XP Pro.
Thanks for all the support!!!
PS: Before flashing the Hard SPL v7, I tried installing the cingular WM6, but didn't make it. That's why I readed almost all the pages and threads here in xda-developers and found that flashing a new bootloader was a very good idea. The rest of the story is known by you.
Hey guys I know this is not the unlocking thread but I tried posting on the thread made by "coke" with no response. So I thought I'd do it here. So here's the story
I have a Sprint Vogue and I was really getting tired of the slow HTC WM 6.1 and all the buttons that I could not modify on the cube (which is useless cuz I dont use any of the them). So I decided to try out a new rom with 6.1 and touchflo 2D.
I went to the ppcgeeks forum to unlock the phone, followed the instructions, read and reread the posts. Finally decided to give it a go. Everything went smoothly until the last step (exitbl) of coke 2.31. It kept telling me to disable USB on activesync and then the program would just shut down! ?? And yes I did disable the USB option for the activesync before that step. I looked under the device information and realized that nothing has changed interms of the ROM. So I tried it again and again (4 times). Then I just reinstalled the HTC 6.1 rom with the 3.42.30 radio... So any ideas on why this may be happening? I promise I followed all the steps
My second question is, in your opinions, what is the most reliable, stable and fast Touch 6.1 rom? Let me know if you have an opinion.
Thanks so much in advance, any help would be appreciated.
I had what sound like the same problem yesterday.
my post is over at ppcgeeks.
"I disconnected but I did not see the phone exit bootloader mode and reset itself.
....
What should I do from here?
Reboot phone, soft reset, hard reset? - go have fun?
....
I did a couple soft resets and have been playing around with it,
I guess I upgraded right... but it was weird there at the end, instructions not the clearest to me, i guess."
mine seems to be working fine, except the weather thing.
shows
in the About section my phone reads
WM 6.1 Pro
CE OS 5.2.21041
Device Information reads
ROM version 1.05.Alltel
Radio version 3.42.30
PRL Version 30008
PRI version 2.02_011
I was kinda scared to do another hard reset b/c I had already changed a bunch of settings.
Sorry if this doesn't help you too much,
but it is nice to know I'm not the only one with this issue
.
Hmm sounds like a similar problem. But I thought it wasn't unlocked unless we saw 2.31.coke somewhere in the device information.
As far as I know, hard reset did not hurt the phone. I tried installing that unlocker 4 times then went with the original HTC rom and it still turned out just like before. It installed the rom fine
Yeah I am still concerned about how it wont go through the exitbl step...
moonwoo said:
Hey guys I know this is not the unlocking thread but I tried posting on the thread made by "coke" with no response. So I thought I'd do it here. So here's the story
I have a Sprint Vogue and I was really getting tired of the slow HTC WM 6.1 and all the buttons that I could not modify on the cube (which is useless cuz I dont use any of the them). So I decided to try out a new rom with 6.1 and touchflo 2D.
I went to the ppcgeeks forum to unlock the phone, followed the instructions, read and reread the posts. Finally decided to give it a go. Everything went smoothly until the last step (exitbl) of coke 2.31. It kept telling me to disable USB on activesync and then the program would just shut down! ?? And yes I did disable the USB option for the activesync before that step. I looked under the device information and realized that nothing has changed interms of the ROM. So I tried it again and again (4 times). Then I just reinstalled the HTC 6.1 rom with the 3.42.30 radio... So any ideas on why this may be happening? I promise I followed all the steps
My second question is, in your opinions, what is the most reliable, stable and fast Touch 6.1 rom? Let me know if you have an opinion.
Thanks so much in advance, any help would be appreciated.
Click to expand...
Click to collapse
Yeah, the directions can be a bit confusing over there on that thread
Basically here are the steps
Download the 2.31 unlocker
Download the ROM you want to use (my personal preference is this one for a TF2D style or this one for a WinMO 6.5 style interface that has TF2D included to switch back and for - both very stable, fast and clean and the thread is very active for help (especially if your on Verizon or Bell which can have issues)
from there, use WinRAR to extract each file into separate folders
then Put your phone in bootloader mode (press and hold power+camera+stylus in reset until 3-color screen comes up)
At this point at the bottom of the screen it will say Serial, plug it into the USB cable or cradle and it should change to USB
Start the exe in the 2.31 and follow the directions (you may get some errors about sleep4.exe just click on OK as it keeps occuring its a XP/Windows7 64 bit issue if that is what your using)
At the point where it tell you to disconect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
once complete, reboot, allow it to do its thing then reboot and go back into bootloader again during reboot you should see coke 2.31 in the upper left if so your ready to go
plug it into your USB/Cradle again and then go into the ROM folder you extracted the ROM into
Once the screen on your phone says USB again go to the folder and double click on the RomUpdateUtility.exe file and follow the directions again, it may take some time so be paitent
once the phone flashes and reboots, let it run and do its thing to the and reboot itself then (and here is an important step for stability) once it starts up do a hard reset (red+green+stylus in reset hole) hit the enter button (center of D-Pad) it will reflash the phone and then red key (send) when prompted
then go thought the setup again, this time you can actually set things up as your keeping them this time and once things are done and your at the start screen on your phone power off (not reset) the phone and then start it up again - seems doing it this way takes care of alot of little issues that will come up before they can happen
Depending on your carrier be sure to have one of the DCD Carrier Cabs as well especially for the 6.5 ROM as it is a generic ROM and some have reported needing to run the DCD Carrier Cab for the service they use to get on the internet and use GPS and the like
Hope that clears up things a bit LOL
Detroit Doug
Doug, when I go into the bootloader it DOES say SPL-2.31.Coke. Does that mean that it is all set? Also this time, it still asked me to disable active sync at this time (at the exitbl step) do you have to run that step to complete the unlock?
This is what my bootloader image says
VOGU100 NFG
SPL-2.31.CoKe
CPLD-3
Let me know if I need to run the exitbl or if I am set to load the rom. Thanks so much for your help!
moonwoo said:
Doug, when I go into the bootloader it DOES say SPL-2.31.Coke. Does that mean that it is all set? Also this time, it still asked me to disable active sync at this time (at the exitbl step) do you have to run that step to complete the unlock?
This is what my bootloader image says
VOGU100 NFG
SPL-2.31.CoKe
CPLD-3
Let me know if I need to run the exitbl or if I am set to load the rom. Thanks so much for your help!
Click to expand...
Click to collapse
Your all set to flash if in bootloader it says as your phone does SPL-2.31.CoKe
you all unlocked and ready to go ... just put your phone in bootloader mode then connect the phone to your PC "serial" will change to "USB" and then run the RomUpdateUtility.exe file and follow along with the bouncing ball, do the watusi, wipe hands on pants - whatever helps you pass the time
but follow the steps as outlined above with the hard-resets and power-offs and the like, believe me its better to solve the issues before they occur than wait and have to start over
Detroit Doug
Doug, it worked like a charm. I did not know that the last step of the unlocker was not required. I installed 6.1 with Touchflo 2D. Looks and feels .. wow. it's the coolest thing I've seen. I've followed all your step including a hard reset before I started using it. So far the speed is impressive.
Couple more questions for you since you are an expert at this.
1. If I reload the factory default ROM, will it reset everything back to normal and can I keep reverting back and forth between different ROMs without any consequences?
2. It (the NFSFAN's 6.1 rom) seems to use less Storage memory (137 free vs HTC's ~100 free) but much more Program memory (59 free vs. ~80 in HTC's) than the HTC default. Any ideas or concerns about this?
All in all thanks so much! Hopefully as I learn more and more I will be able to contribute things too. You are right. This is so cool and highly addictive!!
Take care~ BTW I am in Lansing Go State!
moonwoo said:
Doug, it worked like a charm. I did not know that the last step of the unlocker was not required. I installed 6.1 with Touchflo 2D. Looks and feels .. wow. it's the coolest thing I've seen. I've followed all your step including a hard reset before I started using it. So far the speed is impressive.
Couple more questions for you since you are an expert at this.
1. If I reload the factory default ROM, will it reset everything back to normal and can I keep reverting back and forth between different ROMs without any consequences?
2. It (the NFSFAN's 6.1 rom) seems to use less Storage memory (137 free vs HTC's ~100 free) but much more Program memory (59 free vs. ~80 in HTC's) than the HTC default. Any ideas or concerns about this?
All in all thanks so much! Hopefully as I learn more and more I will be able to contribute things too. You are right. This is so cool and highly addictive!!
Take care~ BTW I am in Lansing Go State!
Click to expand...
Click to collapse
Glad it worked, and Ill try to answer you concerns
1 -Now that it is unlocked go ahead and swap ROMs all you want to, the tricky part is the stock ROM, flashing back to stock can and will revert your radio (if youve upgraded it) and ca cause issues with the unlocker, but a simple run of the unlocker 2.31 again can correct it
2 - NFSFAN like other Chefs have ways of moving data/programs around when they cook up these ROMs utilizing whatever kitchen program they personally prefer that being the case how they data/programs get pushed about can create the speediness you now see in your phone by freeing up the RAM for apps and the like and pushing programs off to the side optimizing how the device should have been setup from the start
As for that, Ive been using his ROMs as well as some others for quite some time and have had little to no issues with how he places the progs and data so I wouldnt worry about it
Yeah, Live in Las Vegas now - but Michigan will ALWAYS be home Go Red Wings !!!!
Detroit Doug
Thanks Doug, for all your information. Your answers were great! Hopefully I wont need too much more help in the future. i'm learning~
Don't mean to go off on a little tangent, but I find this post really helpful and was wondering if you, Doug, or someone else could provide a link to this 2.31 unlocker or whatever it is. Thanks in advance.
hibbiejibbie3 said:
Don't mean to go off on a little tangent, but I find this post really helpful and was wondering if you, Doug, or someone else could provide a link to this 2.31 unlocker or whatever it is. Thanks in advance.
Click to expand...
Click to collapse
http://forum.ppcgeeks.com/showthread.php?t=20370
Detroit Doug
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Reddog80p said:
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Click to expand...
Click to collapse
Check your PM over at PPCGeeks
Detroit Doug
Reddog80p said:
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Click to expand...
Click to collapse
From Detroit_Doug
At the point where it tell you to disconnect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
Maybe wait longer if you can,
I reckon some pc take longer to fully recognize[process] the disconnect and reconnect procedure.
example: disconnect > wait 20-30 seconds > reconnect > wait 20-30 seconds > then continue
I had that same issue and waiting longer during this process helped
.
I can't even get to that point. With active sync on as soon as I start the unlocker RUU it gets the info from my phone and shows the current rom 3.14.605.1 ....I click update and it shows 2.31 unlocker I hit next and then the install status bar comes up on my desktop and my phone goes into bootloader mode and the active sync connection drops and I get the 262 connection error. If I start the RUU with my phone in bootloader usb mode already it does not detect my current rom and I click next. click next to 2.31 unlocker, and it goes through the same steps and I get the same error. Is there anything I have to do to my phone prior to running the RUU. My phone is a verizon xv6900 running wm 6.1 rom 3.14.605.1 with radio 3.37.78
I have the same problem with my new sprint touch. I get error 262 at 0%, did they change something in these new phone that won't allow us to unlock?
Rom is 3.03.651.4
radio 3.42.30
I think I got it, what I did was not to extract the vogue_unlocker_MFG_2.31.exe file but to run it. I had activesync set up and connected, then just ran the unlocker, don't extract it. It will shut off activesnyc and put my phone in to the 3 color screen, form there, just follow the directions. Also I didn't have to run the exitbl step as my phone auttomatically exit and restarted.
I ended up having to re-run the .041 unlocker and then the 2.31 unlocker and it ended up working for me. I'm not sure why I had to because I Had the same bootloader info prior to running the 2.31 unlocker in the first place. The 6.5 rom and gps rom has been working flawlessly for a week now, the only thing I had to do was call up VZW (*8889) the guy answered "account investigations" LOL I told him I had to hard reset and my phone wouldn't authenticate and he asked me to call back from another line. I told him that I had no landline and he said thats fine I can override it just call back right away whenever you get to another phone. That was on friday and I have not called back but I've been able to text, make and receive calls so I don't think I will unless I have to.
gooney said:
I think I got it, what I did was not to extract the vogue_unlocker_MFG_2.31.exe file but to run it. I had activesync set up and connected, then just ran the unlocker, don't extract it. It will shut off activesnyc and put my phone in to the 3 color screen, form there, just follow the directions. Also I didn't have to run the exitbl step as my phone auttomatically exit and restarted.
Click to expand...
Click to collapse
thank you! i did that and it worked for me.
yeah, it says right in the directions over there to just run the exe it will create a temp folder and run the RUU itself from there
Extracting it and running it will always cause issues
also - Ignore the sleep4.exe or whatever if you encounter it - it is a legacy exe that is called that isnt used anymore, wont affect the unlocking just hit OK through it
Detroit Doug
Hey there,
After lots of problems with my P3300 (see this thread), I've decided to flash it to see if that helps. I'm not too bothered about getting the GSM working again as I have another phone, but I'd like to be able to run all apps again.
So... I'd like some advice please.
What would be the best ROM for me to use if I just want to use the phone as a GPS device, portable wifi web browser and notepad?
Basically something pretty stripped down with as good battery life as possible.
Is there any advantage with going for WM6 over WM5?
Bear in mind I've never done this before and am currently reading up on all of it.
From what I've read so far I'll have to do the CID unlock first (currently have WM5 in french installed and would like an english ROM)? I think it may be unlocked already but am not sure. Is there a way to check? Do I risk anything if I run USPL even though the phone is already unlocked?
Thanks in advance for any advice!
You can check if your phone is CID unlocked if the SPL number which comes up while booting during the big white HTC screen says 1.11.0000. If it says anything other than that then it's not unlocked.
Best stripped rom for me is Sheen's clean base version 3. Check it out, it's on the first page of the thread.
alternatively, if u want fast and stripped, go for yues extraclean (see my signature)
greetz
ferfecir Clean
This is the best clean rom which is a modified version of Yues clean with 30mb free ram.
http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir
mta33 said:
This is the best clean rom which is a modified version of Yues clean with 30mb free ram.
http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir
Click to expand...
Click to collapse
Pagepool 4 MB
RAM 32 MB
ROM 69 MB
Thanks for the replies. My SPL says 1.12.0000 so I guess I need to do the CID unlock.
Ferfecir Build 20931 looks like the most promising from those.
Can anyone please point me to a good tutorial for flashing the ROM via activesync? I'd rather not have to format the memory card if I can avoid it and my soft reset button is broken. (I have serached but had no luck)
Thanks!
download uspl from here http://forum.xda-developers.com/showthread.php?t=311403
and any rom you want...
unpack the uspl
plug the cable in the device and establish a usb connection
run the "start_uspl.exe" be patient...after being prompted to click some "next buttons" follow the procedure...and i mean it...follow the procedure...that with 50% battery,no programs running on the pc,no unplugging the cable and so on...
and you will have the uspl flashed
go to boot loader...The bootloader is invoked by pressing down the Power and Voicedialer buttons simultaneously, and using the stylus at the same time to press the RESET button at the left side. Continue pressing the two buttons for a few seconds after pressing and releasing the reset button until the bootloader screen appears.
if uspl says 1.11.000 then you are good to go
now you can flash any rom (cooked for artemis) and any artemis radio (i recommend you the 3.34.90.) onto your artemis
simply download,extract,run the rom update utility (RUU) ,follow the procedure and watch the show...
if you ever get an error during flash or anywhere else in the rom update utility...refer to this page and troubleshoot your troubles http://wiki.xda-developers.com/index.php?pagename=RUU_Errors
if you get an error saying invalid file size or something like that (you will get it if you try eg this rom..http://forum.xda-developers.com/showthread.php?t=465291)
go to this thread http://forum.xda-developers.com/showthread.php?t=521406 download the file and flash it if it is an ordinary rom...just run the RUU
afterwards just check it in the bootloader if it says 1.11.cmon it is ok....and you will be able to flash virtually any rom cooked for artemis onto yours
i must be damn crazy to post this thing...because it is all there in the wiki and the forum stickies,believe it or not
Thank you very much for the detailed instructions.
Just two more questions!
My reset button is broken. Can I just turn the phone off and back on to check if I have 1.11.0000 instead of using the bootloader?
And the RUU is this one? http://code.google.com/p/htc-flasher/downloads/list (only file I have for the new Ferfecir ROM is a .nbh, is that all I need?)
Thanks again.
this is a very open-ended question.
Everyone on here will have their own favourite rom....if there was 1 definate fits-all "best" rom ...everyone would be using it..but there isnt and we are all using the rom that suits us best
some people want their phone to be more like an iPod and so the multimedia aspect is a priority along with decent graphics and animated menus
some people want the PDA functionality most so they want a really stripped-down fast rom that is reliable and handles email well
everyone wants to use it their own way....thats why this site exists.
The guys who make these ROMS are the guys who say "this is good, but i want it to be more like THIS."
Follow farukb's (excellent) instructions....unlock your device properly....if you get any problems, search for the answer before asking for help....chances are hundreds of people will have had the same problem and hundreds of people will have already given the answer...and then ....just look around the site. See which roms are available that fit YOUR needs, and flash it....if you dont like it, try another.
I'm trying 6.5 roms at the moment and love it....i've flashed it probably once a week with a new ROM each time a new version is released and have seen the OS evolve....right now i'd say PDhee's Mega 6.5 M2D rom is the best of the bunch providing you're not planning on installing LOTS of exra programs.
that's the beauty of these things, if you dont like the ROM, just try another. Sometimes the ROM won't work quite right (especially if flashing ROMs between different cooks) so just try flashing it again to make sure it resets everythin correctly. If it's still not right, try a different ROM.
farukb said:
i must be damn crazy to post this thing...because it is all there in the wiki and the forum stickies,believe it or not
Click to expand...
Click to collapse
yeah, unfortunately (and it seems to have increased over the last year or so) nost people on here are noobs who can't be bothered to read through some threads or use the search and we just get the same questions asked constantly.
I dont minds helping people....providing they've looked for the answer themselves first.
every time a new rom is released there will be people asking what error 260 or 270 means?, do they need to USPL? etc etc
it's easier to ask someone else to take time out of their day to aswer your question than just type "error 260" into the search box and find out for yourself. They dont consider that people are having to answer these questions 10 times a week, in their own time, for no thanks, just to have the same question asked the next day. Purely becuase they couldn't be bothered to see if anyone else has asked that question before.
sorry...rant over....i love you all
seebasso said:
Thank you very much for the detailed instructions.
Just two more questions!
My reset button is broken. Can I just turn the phone off and back on to check if I have 1.11.0000 instead of using the bootloader?
And the RUU is this one? http://code.google.com/p/htc-flasher/downloads/list (only file I have for the new Ferfecir ROM is a .nbh, is that all I need?)
Thanks again.
Click to expand...
Click to collapse
no
you need to use the reset button (stick the stylus in the reset hole) .
Reset is like turning your computer off and on again
Power button is like turning the monitor off....it doesnt stop programs running and it doesnt properly reboot the device.
Your only alternative is taking the batter out i think (just like pulling the plug out will also reboot your computer).
If you havent already run USPL, then you probably WILL need to do it.
i dont know the specific ROM you're talking about, but just an NBH file will NOT work. You need the EXE file to run it.
Just download any suitable ROM off this site and it will have the whole package....if you're downloading from another site you'll have to ak that other site for help
my reset button doesn't work. i took the phone apart to change the touchscreen and must have misaligned something when putting it back together. sticking the stylus in the hole doesn't do anything anymore. will take the battery out instead, thanks.
regarding the rom, it is one i downloaded from here: http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir
the rar file downloaded from 4share (http://www.4shared.com/file/112067347/72728603/ARTEIMG-Ferfecir_-_20931_en_gncel_hali.html) only contains the nbh, no exe.
and for the record, i've spent all afternoon/evening researching this, searching this forum and the wiki etc! i appreciate it's annoying answering the same noob questions over and over again but i thought my thread was specific enough to warrant it and am grateful for all the replies.
seebasso said:
regarding the rom, it is one i downloaded from here: http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir
the rar file downloaded from 4share (http://www.4shared.com/file/112067347/72728603/ARTEIMG-Ferfecir_-_20931_en_gncel_hali.html) only contains the nbh, no exe.
and for the record, i've spent all afternoon/evening researching this, searching this forum .....
Click to expand...
Click to collapse
...yeah, and if you read ferfercirs description fully, you will come past "sd-card-flashing" which is the way to flash the *.nbh -part of your rom in a way without needing an activesync connecton
greetz
i did read that bit
but as mentioned a couple of times in this thread already, my reset button is not operational so i cannot use bootloader (afaik). so i assumed there was another way.
but i guess i'll find a rom that comes an an exe and save myself some trouble
no need to keep searching,
u can simple take the provided *.nbh file that came without an exe, rename it to ruu_signed.nbh, exchange the existing RUU from a complete installer-routine and off u go, provided u have used uspl first
greetz
ok thank you once again, i'll try it tonight.
one final question! do i need to have a sim card inserted while running USPL or does it not matter?
It is recommended to remove both your SIM card and your MicroSD card during any type of flashing, whether it be USPL or ROM. Even my reset button is not working anymore, my phone got dropped in water and I had to give it for repairs. After motherboard change they assembled it slightly wrong I guess, and it doesn't work. But I can still get into bootloader by just pressing the Voice record and power buttons together for 10 seconds. Try that.
Secondly, I hate to be plugging myself here, but I have just cooked a clean 6.1 ROM myself, with the latest build of 6.1 that is 21054. you might want to check that out, it comes with the full package and not just the nbh
here it is - (http://forum.xda-developers.com/showthread.php?t=551728)
Again, sorry, but Im giving you an option thats all
thormdac said:
no need to keep searching,
u can simple take the provided *.nbh file that came without an exe, rename it to ruu_signed.nbh, exchange the existing RUU from a complete installer-routine and off u go, provided u have used uspl first
greetz
Click to expand...
Click to collapse
ok i need help again sorry! i tried this but i got an error after 5% saying the .nbh was an invalid size
i used the ROMUpdateUtility.exe from Arte_WM65_23009_M2D_Mega_beta1 ROM (i removed Arte_WM65_23009_Mega_b1.nbh from the folder and replaced it with Ferfecir's .nbh which I had renamed to ruu_signed.nbh)
What did I do wrong?
I ended up flashing with Arte_WM65_23009_Mega_b1.nbh and it worked great but that ROM is too much for me and I want Ferfecir's simpler one.
Thanks
You need to flash the newer USPL which allows nbh files of a smaller size to be flashed.
thanks! it worked. everything working perfectly and my gsm works again too. woohoo.
would have been nice if someone would have warned us "rookies" about AlexSS ROM being a Beta Test and that it would expire on it's own and throw a screen up that reads "this concludes the beta test of this software, yada, yada,yada". problem is when you try to flash another rom you can't because it won't activesync. still playing with it. have done soft/hard resets but seems by the time you install the certificate allow and run sda unlock, that damn message pops up again, cutting off the activesync. now i do have 1 question. when in bootloader mode will the phone activesync? in the sticky's it's said to hit the camera button.as in 1. there's 2, the Alt/Fn and sym buttons for the camera app. i will also try the CID unlock. any suggestions ? what am i doing wrong ?
If you have a problem with a ROM use the ROM thread don't start new...
Get into bootloader and flash stock ROM, then choose another ROM, i'm sure that if you read the thread a user already noted this.
Thread closed.
Morning,
I have tried countless times to upgrade my ROM, Custom RUU, task29, etc.... Everything ends exactly the same; Screen on the phone shows the multi color background with "USB" at the bottom of the page, then both my laptop and the phone show a status bar that never moves off of 0%. I let it sit for a while, then I get some form or another of a communication error. It wants me to perform a "Recovery" but that never works either. I always have the same results.
When I try to use the HardSPL file, I get an error that states "Windows cannot access the specefic device, path or file. You may not have the appropriate permissions to access them." It does not matter how I try it or "Run as Administrator" it still does not work.
When I connect my phone to the laptop, Activesync kicks in and establishes a connection, when the screen goes multi color with "USB" at the bottom, I hear the laptop ding as it does when a USB device is disconnected. I don't hear any dings as if it were reconnecting. I have tried this on 2 different Win7 machines and get the same results.
I would love to flash the ROM on this thing as it is over bloated with apps that I don't want/need/care to have! I know this phone has the potential to be very a very cool phone, so I am begging for help on this one.
I have succefully flashed the ROM on my old HTC Fuze phone with no issue at all. I have to wonder when I see the threads for doing this is over 2 years old if that has anything to do with it.
If anyone could please assist me in getting this sorted so I can open my phone up to new and different possibilities, that would be great!
Thanks
Joe
B 80
R 4.48.25.89
G 61.39tc.25.30h
D 1.59.67150
1. So your only problem is that you can't hardspl. Then why do you say that nothing from this site works?
2. Ask hardspl questions in the hardspl thread.
3. Try entering bootloader and then plugin your usb and perform a hardspl.
For further help, you should really ask in the hardspl thread
Lennyz1988 said:
1. So your only problem is that you can't hardspl. Then why do you say that nothing from this site works?
Click to expand...
Click to collapse
Yeah, the OP is really only having problems with HardSPL, and nothing else (not being able to run Task29 or a flash a custom ROM is due to not being HardSPLed). Why flame the entire website, and the thousands of ROMs, CABs, and other stuff that people dedicate their time and hard work to accomplish?
If you are using Windows 7, you should not be using Active Sync, you should be using Windows Mobile Device Center.
http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
This may be the problem. But HardSPL on Windows 7 is a known issue if you read the HardSPL thread. It works for some W7 user, and not for others. If this continues to be the case, your best bet is to find a XP machine and HardSPL from there. Other things, like flashing a custom ROM should work fine on your W7 machine (using WMDC).