Related
Hello everyone.
I have just bought my Hermes (AT&T 8525) after one year of planing so. It came with WM5. I downloaded some of the ROMSs, radio and bootloaders commented here. I tried reading all the vast infromation in this forum and the wiki, but still having a problem.
THE PROBLEM IS AS FOLLOW:
When I start the flashing process, using HTC_TyTN_WWE_3[1].54.255.3_6275_1.48.00.10_108.exe or RUU_Hermes_CINGULAR_WWE_3.1.57.502.1_6275_1.48.00.00_108
... everything goes well, until the progress bar appears in my PC. When it appears, ActiveSync in my PC closes and my Hermes goes to stand by (the lcd goes off) so I cannot complete the installation process.
The phone works pretty well and I'm really amazed for all its capabilities. But still, I'm stucked with wm5.
Why do you think this happened?
PS: I flashed the radio (1.51.00.10) and bootloader (HARD SPL v7). My ROM version is 2.15.502.3. I use "ActiveStink" to sync my files without problems.
Any advice will be more than welcome!!
I'm no expert but that appears to be normal behaviour!
ActiveSync is only used at the start of the process. After a few files have been transfered, Activesync is closed and a different link is established. If you just leave it for a short while longer, a progress bar should appear on the Hermes too.
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
todd_jg said:
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
Click to expand...
Click to collapse
I'm having the same problem - always have. The message tells me that I'm disconnected and that I should check my USB connect etc. I left that box up there for about 15 minutes. Now I've closed the box and have waited several minutes with no activity. This is pretty aggravating. Thanks for any help.
try turning off your antivirus aplication. thats work for me flashing my tytn to wm6.
I've done everything.... I guess
Hi...
Yes, I consulted the www.mrvanx.org, excellent tutorials.
I flashed without problem the radio and bootloader. The progress bar started to "progress" and everything was fine. The only problem I have is flashing the WM6.
I don't remember where, but I readed that flashing the bootloader "Hard SLP v7" causes my HTC not to accept any Oficial WM6 ROM. The article said that I only had the chance to flash a coocked or modified ROMs. Is this true?
If not... what else can it be? I also closed all my applicacations including the antivirus, goback, disabled the internet connection, the logictec mouse center, etc. and nothing, the same as Chicoh happens to me.
"Error 260: Connection... check the USB cable bla bla bla."
Should I restart in safe mode to do the flashing?
Should I try to install a modified ROM?
Have in mind I've tried three different official ROMs: WWE, Cingular and spanish.
Thanks to all the comunity!!!
Saludos desde México!!
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
liquidsilver said:
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
Click to expand...
Click to collapse
I'm trying that as we speak. I have a good feeling about this. I'm a little concerned that I didn't think of it though. Makes perfect sense - Skip the middle man.
UPDATE: Crap. No luck. Thanks all the same though. I'm not giving up.
What OS are you using, xp or vista? My vista 'top had the same problem wouldnt flash for the longest time and i had to use my xp.
However, it does work now. Not entirely sure why.
Now I had success!!!
Hello my friends.
It seems that the article I readed days ago detailing that after flashing the Hard SPL v7, I could only install a modified ROM, not an official one from HTC or Cingular.
I downloaded Black Satin and installed it without any troubles. The entire process lasted only 3 minutes!!!
I wanted to have an official ROM, don't ask me why, and never tried the "other" ROMs that are actually excellent!!! some apps that were on WM5 are not in WM6, which is kind of sad, but if there's something that I love of WM Smartphones is that I can download and install whatever I want or develop it if it doesn't exist!!!
By the way, I use Windows XP Pro.
Thanks for all the support!!!
PS: Before flashing the Hard SPL v7, I tried installing the cingular WM6, but didn't make it. That's why I readed almost all the pages and threads here in xda-developers and found that flashing a new bootloader was a very good idea. The rest of the story is known by you.
Hey guys I know this is not the unlocking thread but I tried posting on the thread made by "coke" with no response. So I thought I'd do it here. So here's the story
I have a Sprint Vogue and I was really getting tired of the slow HTC WM 6.1 and all the buttons that I could not modify on the cube (which is useless cuz I dont use any of the them). So I decided to try out a new rom with 6.1 and touchflo 2D.
I went to the ppcgeeks forum to unlock the phone, followed the instructions, read and reread the posts. Finally decided to give it a go. Everything went smoothly until the last step (exitbl) of coke 2.31. It kept telling me to disable USB on activesync and then the program would just shut down! ?? And yes I did disable the USB option for the activesync before that step. I looked under the device information and realized that nothing has changed interms of the ROM. So I tried it again and again (4 times). Then I just reinstalled the HTC 6.1 rom with the 3.42.30 radio... So any ideas on why this may be happening? I promise I followed all the steps
My second question is, in your opinions, what is the most reliable, stable and fast Touch 6.1 rom? Let me know if you have an opinion.
Thanks so much in advance, any help would be appreciated.
I had what sound like the same problem yesterday.
my post is over at ppcgeeks.
"I disconnected but I did not see the phone exit bootloader mode and reset itself.
....
What should I do from here?
Reboot phone, soft reset, hard reset? - go have fun?
....
I did a couple soft resets and have been playing around with it,
I guess I upgraded right... but it was weird there at the end, instructions not the clearest to me, i guess."
mine seems to be working fine, except the weather thing.
shows
in the About section my phone reads
WM 6.1 Pro
CE OS 5.2.21041
Device Information reads
ROM version 1.05.Alltel
Radio version 3.42.30
PRL Version 30008
PRI version 2.02_011
I was kinda scared to do another hard reset b/c I had already changed a bunch of settings.
Sorry if this doesn't help you too much,
but it is nice to know I'm not the only one with this issue
.
Hmm sounds like a similar problem. But I thought it wasn't unlocked unless we saw 2.31.coke somewhere in the device information.
As far as I know, hard reset did not hurt the phone. I tried installing that unlocker 4 times then went with the original HTC rom and it still turned out just like before. It installed the rom fine
Yeah I am still concerned about how it wont go through the exitbl step...
moonwoo said:
Hey guys I know this is not the unlocking thread but I tried posting on the thread made by "coke" with no response. So I thought I'd do it here. So here's the story
I have a Sprint Vogue and I was really getting tired of the slow HTC WM 6.1 and all the buttons that I could not modify on the cube (which is useless cuz I dont use any of the them). So I decided to try out a new rom with 6.1 and touchflo 2D.
I went to the ppcgeeks forum to unlock the phone, followed the instructions, read and reread the posts. Finally decided to give it a go. Everything went smoothly until the last step (exitbl) of coke 2.31. It kept telling me to disable USB on activesync and then the program would just shut down! ?? And yes I did disable the USB option for the activesync before that step. I looked under the device information and realized that nothing has changed interms of the ROM. So I tried it again and again (4 times). Then I just reinstalled the HTC 6.1 rom with the 3.42.30 radio... So any ideas on why this may be happening? I promise I followed all the steps
My second question is, in your opinions, what is the most reliable, stable and fast Touch 6.1 rom? Let me know if you have an opinion.
Thanks so much in advance, any help would be appreciated.
Click to expand...
Click to collapse
Yeah, the directions can be a bit confusing over there on that thread
Basically here are the steps
Download the 2.31 unlocker
Download the ROM you want to use (my personal preference is this one for a TF2D style or this one for a WinMO 6.5 style interface that has TF2D included to switch back and for - both very stable, fast and clean and the thread is very active for help (especially if your on Verizon or Bell which can have issues)
from there, use WinRAR to extract each file into separate folders
then Put your phone in bootloader mode (press and hold power+camera+stylus in reset until 3-color screen comes up)
At this point at the bottom of the screen it will say Serial, plug it into the USB cable or cradle and it should change to USB
Start the exe in the 2.31 and follow the directions (you may get some errors about sleep4.exe just click on OK as it keeps occuring its a XP/Windows7 64 bit issue if that is what your using)
At the point where it tell you to disconect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
once complete, reboot, allow it to do its thing then reboot and go back into bootloader again during reboot you should see coke 2.31 in the upper left if so your ready to go
plug it into your USB/Cradle again and then go into the ROM folder you extracted the ROM into
Once the screen on your phone says USB again go to the folder and double click on the RomUpdateUtility.exe file and follow the directions again, it may take some time so be paitent
once the phone flashes and reboots, let it run and do its thing to the and reboot itself then (and here is an important step for stability) once it starts up do a hard reset (red+green+stylus in reset hole) hit the enter button (center of D-Pad) it will reflash the phone and then red key (send) when prompted
then go thought the setup again, this time you can actually set things up as your keeping them this time and once things are done and your at the start screen on your phone power off (not reset) the phone and then start it up again - seems doing it this way takes care of alot of little issues that will come up before they can happen
Depending on your carrier be sure to have one of the DCD Carrier Cabs as well especially for the 6.5 ROM as it is a generic ROM and some have reported needing to run the DCD Carrier Cab for the service they use to get on the internet and use GPS and the like
Hope that clears up things a bit LOL
Detroit Doug
Doug, when I go into the bootloader it DOES say SPL-2.31.Coke. Does that mean that it is all set? Also this time, it still asked me to disable active sync at this time (at the exitbl step) do you have to run that step to complete the unlock?
This is what my bootloader image says
VOGU100 NFG
SPL-2.31.CoKe
CPLD-3
Let me know if I need to run the exitbl or if I am set to load the rom. Thanks so much for your help!
moonwoo said:
Doug, when I go into the bootloader it DOES say SPL-2.31.Coke. Does that mean that it is all set? Also this time, it still asked me to disable active sync at this time (at the exitbl step) do you have to run that step to complete the unlock?
This is what my bootloader image says
VOGU100 NFG
SPL-2.31.CoKe
CPLD-3
Let me know if I need to run the exitbl or if I am set to load the rom. Thanks so much for your help!
Click to expand...
Click to collapse
Your all set to flash if in bootloader it says as your phone does SPL-2.31.CoKe
you all unlocked and ready to go ... just put your phone in bootloader mode then connect the phone to your PC "serial" will change to "USB" and then run the RomUpdateUtility.exe file and follow along with the bouncing ball, do the watusi, wipe hands on pants - whatever helps you pass the time
but follow the steps as outlined above with the hard-resets and power-offs and the like, believe me its better to solve the issues before they occur than wait and have to start over
Detroit Doug
Doug, it worked like a charm. I did not know that the last step of the unlocker was not required. I installed 6.1 with Touchflo 2D. Looks and feels .. wow. it's the coolest thing I've seen. I've followed all your step including a hard reset before I started using it. So far the speed is impressive.
Couple more questions for you since you are an expert at this.
1. If I reload the factory default ROM, will it reset everything back to normal and can I keep reverting back and forth between different ROMs without any consequences?
2. It (the NFSFAN's 6.1 rom) seems to use less Storage memory (137 free vs HTC's ~100 free) but much more Program memory (59 free vs. ~80 in HTC's) than the HTC default. Any ideas or concerns about this?
All in all thanks so much! Hopefully as I learn more and more I will be able to contribute things too. You are right. This is so cool and highly addictive!!
Take care~ BTW I am in Lansing Go State!
moonwoo said:
Doug, it worked like a charm. I did not know that the last step of the unlocker was not required. I installed 6.1 with Touchflo 2D. Looks and feels .. wow. it's the coolest thing I've seen. I've followed all your step including a hard reset before I started using it. So far the speed is impressive.
Couple more questions for you since you are an expert at this.
1. If I reload the factory default ROM, will it reset everything back to normal and can I keep reverting back and forth between different ROMs without any consequences?
2. It (the NFSFAN's 6.1 rom) seems to use less Storage memory (137 free vs HTC's ~100 free) but much more Program memory (59 free vs. ~80 in HTC's) than the HTC default. Any ideas or concerns about this?
All in all thanks so much! Hopefully as I learn more and more I will be able to contribute things too. You are right. This is so cool and highly addictive!!
Take care~ BTW I am in Lansing Go State!
Click to expand...
Click to collapse
Glad it worked, and Ill try to answer you concerns
1 -Now that it is unlocked go ahead and swap ROMs all you want to, the tricky part is the stock ROM, flashing back to stock can and will revert your radio (if youve upgraded it) and ca cause issues with the unlocker, but a simple run of the unlocker 2.31 again can correct it
2 - NFSFAN like other Chefs have ways of moving data/programs around when they cook up these ROMs utilizing whatever kitchen program they personally prefer that being the case how they data/programs get pushed about can create the speediness you now see in your phone by freeing up the RAM for apps and the like and pushing programs off to the side optimizing how the device should have been setup from the start
As for that, Ive been using his ROMs as well as some others for quite some time and have had little to no issues with how he places the progs and data so I wouldnt worry about it
Yeah, Live in Las Vegas now - but Michigan will ALWAYS be home Go Red Wings !!!!
Detroit Doug
Thanks Doug, for all your information. Your answers were great! Hopefully I wont need too much more help in the future. i'm learning~
Don't mean to go off on a little tangent, but I find this post really helpful and was wondering if you, Doug, or someone else could provide a link to this 2.31 unlocker or whatever it is. Thanks in advance.
hibbiejibbie3 said:
Don't mean to go off on a little tangent, but I find this post really helpful and was wondering if you, Doug, or someone else could provide a link to this 2.31 unlocker or whatever it is. Thanks in advance.
Click to expand...
Click to collapse
http://forum.ppcgeeks.com/showthread.php?t=20370
Detroit Doug
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Reddog80p said:
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Click to expand...
Click to collapse
Check your PM over at PPCGeeks
Detroit Doug
Reddog80p said:
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Click to expand...
Click to collapse
From Detroit_Doug
At the point where it tell you to disconnect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
Maybe wait longer if you can,
I reckon some pc take longer to fully recognize[process] the disconnect and reconnect procedure.
example: disconnect > wait 20-30 seconds > reconnect > wait 20-30 seconds > then continue
I had that same issue and waiting longer during this process helped
.
I can't even get to that point. With active sync on as soon as I start the unlocker RUU it gets the info from my phone and shows the current rom 3.14.605.1 ....I click update and it shows 2.31 unlocker I hit next and then the install status bar comes up on my desktop and my phone goes into bootloader mode and the active sync connection drops and I get the 262 connection error. If I start the RUU with my phone in bootloader usb mode already it does not detect my current rom and I click next. click next to 2.31 unlocker, and it goes through the same steps and I get the same error. Is there anything I have to do to my phone prior to running the RUU. My phone is a verizon xv6900 running wm 6.1 rom 3.14.605.1 with radio 3.37.78
I have the same problem with my new sprint touch. I get error 262 at 0%, did they change something in these new phone that won't allow us to unlock?
Rom is 3.03.651.4
radio 3.42.30
I think I got it, what I did was not to extract the vogue_unlocker_MFG_2.31.exe file but to run it. I had activesync set up and connected, then just ran the unlocker, don't extract it. It will shut off activesnyc and put my phone in to the 3 color screen, form there, just follow the directions. Also I didn't have to run the exitbl step as my phone auttomatically exit and restarted.
I ended up having to re-run the .041 unlocker and then the 2.31 unlocker and it ended up working for me. I'm not sure why I had to because I Had the same bootloader info prior to running the 2.31 unlocker in the first place. The 6.5 rom and gps rom has been working flawlessly for a week now, the only thing I had to do was call up VZW (*8889) the guy answered "account investigations" LOL I told him I had to hard reset and my phone wouldn't authenticate and he asked me to call back from another line. I told him that I had no landline and he said thats fine I can override it just call back right away whenever you get to another phone. That was on friday and I have not called back but I've been able to text, make and receive calls so I don't think I will unless I have to.
gooney said:
I think I got it, what I did was not to extract the vogue_unlocker_MFG_2.31.exe file but to run it. I had activesync set up and connected, then just ran the unlocker, don't extract it. It will shut off activesnyc and put my phone in to the 3 color screen, form there, just follow the directions. Also I didn't have to run the exitbl step as my phone auttomatically exit and restarted.
Click to expand...
Click to collapse
thank you! i did that and it worked for me.
yeah, it says right in the directions over there to just run the exe it will create a temp folder and run the RUU itself from there
Extracting it and running it will always cause issues
also - Ignore the sleep4.exe or whatever if you encounter it - it is a legacy exe that is called that isnt used anymore, wont affect the unlocking just hit OK through it
Detroit Doug
I put the applock on, i reboot, i double click the exe to run the dos thing, i allow my fone to run spl something, i click centre button, it says run the ruu ex, I do, and active sync disconnects before I can do anything else...Error 260...i can wait an hr an nothing happens. I've soft-reset, hard-reset, followed and understood and read every instruction but I just cannot get it to upgrade. The phones unlocked, the apps are unlocked. I've tried it without redoing the applock exe. I'm stuck. Any advice before I call it a day and keep my greedy wanting nature under control. All help much appreciated.
Bimbledwadle said:
I put the applock on, i reboot, i double click the exe to run the dos thing, i allow my fone to run spl something, i click centre button, it says run the ruu ex, I do, and active sync disconnects before I can do anything else...Error 260...i can wait an hr an nothing happens. I've soft-reset, hard-reset, followed and understood and read every instruction but I just cannot get it to upgrade. The phones unlocked, the apps are unlocked. I've tried it without redoing the applock exe. I'm stuck. Any advice before I call it a day and keep my greedy wanting nature under control. All help much appreciated.
Click to expand...
Click to collapse
I will recommend you to grab a cup of coffee or tea and read here: http://forum.xda-developers.com/showthread.php?t=537151 you definitely solve this problem if you follow the step by step guides.
gmaniac2008 ....cup of decaf tea, an i'll be back
Bimbledwadle said:
gmaniac2008 ....cup of decaf tea, an i'll be back
Click to expand...
Click to collapse
.....let us know if you still have some problems after you read the STICKY, I'll be glad to help you
I tried with two of them but I cannot stop my activesync just disconnecting right when it tells me its going to start the update, then I get the error 260...you are not connected. then no matter how long I leave it it doesn't start. ive followed all the instructions to every detail. Im now completely bog-eyed n I cant concentrate anymore, so im leavin it till the morrow. THankx very...ill be back
active-sync problem
well, ive followed every single instance from all the options available and everything goes fine until it gets to the actual updating point and then active-sync cuts off,10 seconds later i get error 260 saying im not connected. Ive left it all alone to see if it will update as the usb cable is still attached but no. I havent had this problem with any other phone update or unlock or debranding. Ive noticed on google that others have the same problem and they were told to leave it running and it will continue to update but on all the options ive left it overnight and it hasnt updated and neither has theirs. All help stops after everyone else has done what ive done, its too near xmas to drown my sorrows but, thanks for help n have a lovely xmas n new year
When you press the center button and the screen turns white do you hear the chime windows make when a USB device is disconnected?
Bimbledwadle said:
well, ive followed every single instance from all the options available and everything goes fine until it gets to the actual updating point and then active-sync cuts off,10 seconds later i get error 260 saying im not connected. Ive left it all alone to see if it will update as the usb cable is still attached but no. I havent had this problem with any other phone update or unlock or debranding. Ive noticed on google that others have the same problem and they were told to leave it running and it will continue to update but on all the options ive left it overnight and it hasnt updated and neither has theirs. All help stops after everyone else has done what ive done, its too near xmas to drown my sorrows but, thanks for help n have a lovely xmas n new year
Click to expand...
Click to collapse
Well, actually when you flash your activesync shut offs but your USB connection stills active, so that's normal.
Did you sda unlock your phone before you flashed?. You should do this every time you flash (well that's why I do), also make sure you remove your sd card; because these can cause error messages while you flash.
Other option can be try another PC or reinstall activesync, sometimes my laptop gets crazy and I get multiple errors when I flash, but when I use my desktop flashing goes smooth
yes I sda unlocked every time....i only have a lappy....i remove my sd card...i will uninstall n reinstall active sync.....I'll check out if any of my daughters' friends have desktops to see if I can do it that way. I shall try all that over xmas n new year n ill let you know how I get on. Many Thanx....
Bimbledwadle said:
yes I sda unlocked every time....i only have a lappy....i remove my sd card...i will uninstall n reinstall active sync.....I'll check out if any of my daughters' friends have desktops to see if I can do it that way. I shall try all that over xmas n new year n ill let you know how I get on. Many Thanx....
Click to expand...
Click to collapse
Ok, I forgot to mention; if you have another USB cable try it also.
Hope that helps ..Merry Christmas and happy new year
im running Windows Mobile Device Center 6.1 for vista as it says active-synce 4.2/4.5 only works with xp. Could this be a problem ? Is this why I'm havin trouble with flashing the roms or am I red-herring myself ?
Bimbledwadle said:
im running Windows Mobile Device Center 6.1 for vista as it says active-synce 4.2/4.5 only works with xp. Could this be a problem ? Is this why I'm havin trouble with flashing the roms or am I red-herring myself ?
Click to expand...
Click to collapse
is there no update on this situation? because i am currently attempting to flash a rom for my friends dash and i am having the same connection error problems. and she has a windows vista laptop. i am not sure if that is what the problem is. convinced its not the cord. during the update process it just disconnects once it gets to about 3 percent.
cediesaid said:
is there no update on this situation? because i am currently attempting to flash a rom for my friends dash and i am having the same connection error problems. and she has a windows vista laptop. i am not sure if that is what the problem is. convinced its not the cord. during the update process it just disconnects once it gets to about 3 percent.
Click to expand...
Click to collapse
3% error solution. Also, make sure you access your PC as an administrator and disable any firewall
Please save sarcasm when responding. I have been reading and would onlt ask for help a last option.
My phone - HTC Pro 2 (I bought it from a authorized t-mobile store)
Need help with - ugrading it to 6.5 or any cooked version that will work
History - my phone is already unlocked as I had unlock kings do it. I tested it and I can put any sim it and it works fine.
Problem - every time I try and install a new rom on it I get one the follwing errors or issues: My usb connection stop when the install starts and the process times out, or I get a host of errors messeges from invild device to wrong version.
I need very simple instructions on what I need to do upgrade my os and then later migrate to some of the really roms I have seen on this site.
Please help.
Did you hardSPL? If not go here: HardSPL
Nothing
I DL'ed the fle and followed directions (auto option). Nothing happened.
bigdaddy67 said:
I DL'ed the fle and followed directions (auto option). Nothing happened.
Click to expand...
Click to collapse
When you read those 11 steps in the HSPL thread, where is it, where you say: nothing happends?
As it stands, you will only be able to install an official T-Mobile ROM if it is a T-Mobile-branded phone.
So installing HardSPL will let you flash whatever ROM you want, any of the official ones (including, say, HTC official 6.5), or one of the fine cooked ones from this forum.
If you are having trouble with HardSPL, you really need to post on that in the HardSPL sticky.
no matter what I do, the connection always times out. It seems my phone will not allow anything rom software to be installed. Where can I find enableapnew.cab? The rom software told me i needed that.
@bigdaddy67
This sounds like a USB issue, try this:
1. Power off your TP2
2. Press and HOLD the volume down button, press and HOLD power button until you see the multi-coloured screen (bootloader mode)
3. Connect your TP2 to your computer via USB
4. You should now see the letters USB at the bottom of the TP2 screen
5. If you DO, run hardSPL
If you DON'T, try a different USB cable and/or port on your computer.
If none of the above helps, take a screen shot of your bootloader screen and post it.
How to get a screenshot:
1. Go to http://www.mymobiler.com and download/install the software.
2. Open it and take a screen shot
3. Post it here.
We are here to help, but need some additional details!!!
Russ
bigdaddy67 said:
no matter what I do, the connection always times out. It seems my phone will not allow anything rom software to be installed. Where can I find enableapnew.cab? The rom software told me i needed that.
Click to expand...
Click to collapse
normally I would tell you to go search but you seem to be in a pickle so here...
Russ
bigdaddy67 said:
Please save sarcasm when responding. I have been reading and would onlt ask for help a last option.
My phone - HTC Pro 2 (I bought it from a authorized t-mobile store)
Need help with - ugrading it to 6.5 or any cooked version that will work
History - my phone is already unlocked as I had unlock kings do it. I tested it and I can put any sim it and it works fine.
Problem - every time I try and install a new rom on it I get one the follwing errors or issues: My usb connection stop when the install starts and the process times out, or I get a host of errors messeges from invild device to wrong version.
I need very simple instructions on what I need to do upgrade my os and then later migrate to some of the really roms I have seen on this site.
Please help.
Click to expand...
Click to collapse
Welcome to forums
Hope this guide help you:
http://forum.xda-developers.com/showthread.php?t=550540
And don´t forget to vote!
bigdaddy67 said:
no matter what I do, the connection always times out. It seems my phone will not allow anything rom software to be installed. Where can I find enableapnew.cab? The rom software told me i needed that.
Click to expand...
Click to collapse
Also, which OS are you running on your PC? If its Windows XP, make sure you download Active Sync and install/run it. If you run Vista / 7, make sure you run the Mobile Device Center.
moved you're thread out of rom dev section, best of luck sir.
Update -
My OS is win xp and copied and installed the cab on my device. then I re-powered hold down the volume and got that tri-color screen with the usb connected. Started the HardSP app and have been waiting for 15 minutes as nothing seems to be working.
Did I miss something?
Got error 262
Ok I finally got an 262 error. I am not what I missed. Dl'ed the cab re-powered holding down vol key started HardSp app.
Help.
Stil need help
I am at home and my pc is vista. Can someone pls help get over this hurdle?
Please Please Please
I haven't been able to unlock my touch. I am using 2.31 unlocker, I run the RUU.exe and get up to the point where the phone shows the gray screen with the %bar. But it stays at 0% and after a few minutes a get Error 262.
I have already re-flashed to my stock ROM, but same results.
Touch (Sprint)
ROM: 3.03.651.4
Radio: 3.42.30
WinMo 6.1
Update:
I have tried on Windows 7 Pro 32-bit, and on Windows XP Pro 32-bit. Same results....
Try this...
I'm sure the thread will be locked and you'll be told to ask in the FAQ's thread or something, but I hate when that's the only thing you get... not helpful enough! So maybe I can sneak in before the lock.
I had this problem a week ago, and for whatever reason, the only thing that worked for me was: 1st, flashing to the latest stock ROM (which you already have), then turning on the phone and letting it connect to Windows Mobile Device Center (Win7) or ActiveSync (WinXP) (do the whole 'connect without configuring device thing) then run the actual unlocker BAT file (Vogue_unlocker.bat) in the 2.31 unlocker.
Trying to manually run the EXE didn't want to work - letting the BAT file do it's thing through activesync actually worked for me.
Maybe it'll help... I hope so! Good luck!
NuAngel
NuAngel said:
I'm sure the thread will be locked and you'll be told to ask in the FAQ's thread or something, but I hate when that's the only thing you get... not helpful enough! So maybe I can sneak in before the lock.
I had this problem a week ago, and for whatever reason, the only thing that worked for me was: 1st, flashing to the latest stock ROM (which you already have), then turning on the phone and letting it connect to Windows Mobile Device Center (Win7) or ActiveSync (WinXP) (do the whole 'connect without configuring device thing) then run the actual unlocker BAT file (Vogue_unlocker.bat) in the 2.31 unlocker.
Trying to manually run the EXE didn't want to work - letting the BAT file do it's thing through activesync actually worked for me.
Maybe it'll help... I hope so! Good luck!
NuAngel
Click to expand...
Click to collapse
Oh come on Nu!
Unlike most other mods, I don't simply lock the thread. I lock it and/or transfer it to the Q&A thread where I answer the question myself. Please don't say these things. I try to keep the Vogue apart from the usual MO in several other fora.
I do it for 2 reasons:
a. To keep clutter to a minimum
b. To have a nice db with solutions to many issues that people may have with their Vogues. Trust me that the Search Engine of this site works much better when you look through a single thread than when you look for threads.
@caquito07,
I am transferring your question over to the Flashing Guide Sticky thread. Please follow up over there.
@Nu,
One last thing... thanks for stepping in
Thread closed.