Hey guys I know this is not the unlocking thread but I tried posting on the thread made by "coke" with no response. So I thought I'd do it here. So here's the story
I have a Sprint Vogue and I was really getting tired of the slow HTC WM 6.1 and all the buttons that I could not modify on the cube (which is useless cuz I dont use any of the them). So I decided to try out a new rom with 6.1 and touchflo 2D.
I went to the ppcgeeks forum to unlock the phone, followed the instructions, read and reread the posts. Finally decided to give it a go. Everything went smoothly until the last step (exitbl) of coke 2.31. It kept telling me to disable USB on activesync and then the program would just shut down! ?? And yes I did disable the USB option for the activesync before that step. I looked under the device information and realized that nothing has changed interms of the ROM. So I tried it again and again (4 times). Then I just reinstalled the HTC 6.1 rom with the 3.42.30 radio... So any ideas on why this may be happening? I promise I followed all the steps
My second question is, in your opinions, what is the most reliable, stable and fast Touch 6.1 rom? Let me know if you have an opinion.
Thanks so much in advance, any help would be appreciated.
I had what sound like the same problem yesterday.
my post is over at ppcgeeks.
"I disconnected but I did not see the phone exit bootloader mode and reset itself.
....
What should I do from here?
Reboot phone, soft reset, hard reset? - go have fun?
....
I did a couple soft resets and have been playing around with it,
I guess I upgraded right... but it was weird there at the end, instructions not the clearest to me, i guess."
mine seems to be working fine, except the weather thing.
shows
in the About section my phone reads
WM 6.1 Pro
CE OS 5.2.21041
Device Information reads
ROM version 1.05.Alltel
Radio version 3.42.30
PRL Version 30008
PRI version 2.02_011
I was kinda scared to do another hard reset b/c I had already changed a bunch of settings.
Sorry if this doesn't help you too much,
but it is nice to know I'm not the only one with this issue
.
Hmm sounds like a similar problem. But I thought it wasn't unlocked unless we saw 2.31.coke somewhere in the device information.
As far as I know, hard reset did not hurt the phone. I tried installing that unlocker 4 times then went with the original HTC rom and it still turned out just like before. It installed the rom fine
Yeah I am still concerned about how it wont go through the exitbl step...
moonwoo said:
Hey guys I know this is not the unlocking thread but I tried posting on the thread made by "coke" with no response. So I thought I'd do it here. So here's the story
I have a Sprint Vogue and I was really getting tired of the slow HTC WM 6.1 and all the buttons that I could not modify on the cube (which is useless cuz I dont use any of the them). So I decided to try out a new rom with 6.1 and touchflo 2D.
I went to the ppcgeeks forum to unlock the phone, followed the instructions, read and reread the posts. Finally decided to give it a go. Everything went smoothly until the last step (exitbl) of coke 2.31. It kept telling me to disable USB on activesync and then the program would just shut down! ?? And yes I did disable the USB option for the activesync before that step. I looked under the device information and realized that nothing has changed interms of the ROM. So I tried it again and again (4 times). Then I just reinstalled the HTC 6.1 rom with the 3.42.30 radio... So any ideas on why this may be happening? I promise I followed all the steps
My second question is, in your opinions, what is the most reliable, stable and fast Touch 6.1 rom? Let me know if you have an opinion.
Thanks so much in advance, any help would be appreciated.
Click to expand...
Click to collapse
Yeah, the directions can be a bit confusing over there on that thread
Basically here are the steps
Download the 2.31 unlocker
Download the ROM you want to use (my personal preference is this one for a TF2D style or this one for a WinMO 6.5 style interface that has TF2D included to switch back and for - both very stable, fast and clean and the thread is very active for help (especially if your on Verizon or Bell which can have issues)
from there, use WinRAR to extract each file into separate folders
then Put your phone in bootloader mode (press and hold power+camera+stylus in reset until 3-color screen comes up)
At this point at the bottom of the screen it will say Serial, plug it into the USB cable or cradle and it should change to USB
Start the exe in the 2.31 and follow the directions (you may get some errors about sleep4.exe just click on OK as it keeps occuring its a XP/Windows7 64 bit issue if that is what your using)
At the point where it tell you to disconect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
once complete, reboot, allow it to do its thing then reboot and go back into bootloader again during reboot you should see coke 2.31 in the upper left if so your ready to go
plug it into your USB/Cradle again and then go into the ROM folder you extracted the ROM into
Once the screen on your phone says USB again go to the folder and double click on the RomUpdateUtility.exe file and follow the directions again, it may take some time so be paitent
once the phone flashes and reboots, let it run and do its thing to the and reboot itself then (and here is an important step for stability) once it starts up do a hard reset (red+green+stylus in reset hole) hit the enter button (center of D-Pad) it will reflash the phone and then red key (send) when prompted
then go thought the setup again, this time you can actually set things up as your keeping them this time and once things are done and your at the start screen on your phone power off (not reset) the phone and then start it up again - seems doing it this way takes care of alot of little issues that will come up before they can happen
Depending on your carrier be sure to have one of the DCD Carrier Cabs as well especially for the 6.5 ROM as it is a generic ROM and some have reported needing to run the DCD Carrier Cab for the service they use to get on the internet and use GPS and the like
Hope that clears up things a bit LOL
Detroit Doug
Doug, when I go into the bootloader it DOES say SPL-2.31.Coke. Does that mean that it is all set? Also this time, it still asked me to disable active sync at this time (at the exitbl step) do you have to run that step to complete the unlock?
This is what my bootloader image says
VOGU100 NFG
SPL-2.31.CoKe
CPLD-3
Let me know if I need to run the exitbl or if I am set to load the rom. Thanks so much for your help!
moonwoo said:
Doug, when I go into the bootloader it DOES say SPL-2.31.Coke. Does that mean that it is all set? Also this time, it still asked me to disable active sync at this time (at the exitbl step) do you have to run that step to complete the unlock?
This is what my bootloader image says
VOGU100 NFG
SPL-2.31.CoKe
CPLD-3
Let me know if I need to run the exitbl or if I am set to load the rom. Thanks so much for your help!
Click to expand...
Click to collapse
Your all set to flash if in bootloader it says as your phone does SPL-2.31.CoKe
you all unlocked and ready to go ... just put your phone in bootloader mode then connect the phone to your PC "serial" will change to "USB" and then run the RomUpdateUtility.exe file and follow along with the bouncing ball, do the watusi, wipe hands on pants - whatever helps you pass the time
but follow the steps as outlined above with the hard-resets and power-offs and the like, believe me its better to solve the issues before they occur than wait and have to start over
Detroit Doug
Doug, it worked like a charm. I did not know that the last step of the unlocker was not required. I installed 6.1 with Touchflo 2D. Looks and feels .. wow. it's the coolest thing I've seen. I've followed all your step including a hard reset before I started using it. So far the speed is impressive.
Couple more questions for you since you are an expert at this.
1. If I reload the factory default ROM, will it reset everything back to normal and can I keep reverting back and forth between different ROMs without any consequences?
2. It (the NFSFAN's 6.1 rom) seems to use less Storage memory (137 free vs HTC's ~100 free) but much more Program memory (59 free vs. ~80 in HTC's) than the HTC default. Any ideas or concerns about this?
All in all thanks so much! Hopefully as I learn more and more I will be able to contribute things too. You are right. This is so cool and highly addictive!!
Take care~ BTW I am in Lansing Go State!
moonwoo said:
Doug, it worked like a charm. I did not know that the last step of the unlocker was not required. I installed 6.1 with Touchflo 2D. Looks and feels .. wow. it's the coolest thing I've seen. I've followed all your step including a hard reset before I started using it. So far the speed is impressive.
Couple more questions for you since you are an expert at this.
1. If I reload the factory default ROM, will it reset everything back to normal and can I keep reverting back and forth between different ROMs without any consequences?
2. It (the NFSFAN's 6.1 rom) seems to use less Storage memory (137 free vs HTC's ~100 free) but much more Program memory (59 free vs. ~80 in HTC's) than the HTC default. Any ideas or concerns about this?
All in all thanks so much! Hopefully as I learn more and more I will be able to contribute things too. You are right. This is so cool and highly addictive!!
Take care~ BTW I am in Lansing Go State!
Click to expand...
Click to collapse
Glad it worked, and Ill try to answer you concerns
1 -Now that it is unlocked go ahead and swap ROMs all you want to, the tricky part is the stock ROM, flashing back to stock can and will revert your radio (if youve upgraded it) and ca cause issues with the unlocker, but a simple run of the unlocker 2.31 again can correct it
2 - NFSFAN like other Chefs have ways of moving data/programs around when they cook up these ROMs utilizing whatever kitchen program they personally prefer that being the case how they data/programs get pushed about can create the speediness you now see in your phone by freeing up the RAM for apps and the like and pushing programs off to the side optimizing how the device should have been setup from the start
As for that, Ive been using his ROMs as well as some others for quite some time and have had little to no issues with how he places the progs and data so I wouldnt worry about it
Yeah, Live in Las Vegas now - but Michigan will ALWAYS be home Go Red Wings !!!!
Detroit Doug
Thanks Doug, for all your information. Your answers were great! Hopefully I wont need too much more help in the future. i'm learning~
Don't mean to go off on a little tangent, but I find this post really helpful and was wondering if you, Doug, or someone else could provide a link to this 2.31 unlocker or whatever it is. Thanks in advance.
hibbiejibbie3 said:
Don't mean to go off on a little tangent, but I find this post really helpful and was wondering if you, Doug, or someone else could provide a link to this 2.31 unlocker or whatever it is. Thanks in advance.
Click to expand...
Click to collapse
http://forum.ppcgeeks.com/showthread.php?t=20370
Detroit Doug
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Reddog80p said:
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Click to expand...
Click to collapse
Check your PM over at PPCGeeks
Detroit Doug
Reddog80p said:
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Click to expand...
Click to collapse
From Detroit_Doug
At the point where it tell you to disconnect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
Maybe wait longer if you can,
I reckon some pc take longer to fully recognize[process] the disconnect and reconnect procedure.
example: disconnect > wait 20-30 seconds > reconnect > wait 20-30 seconds > then continue
I had that same issue and waiting longer during this process helped
.
I can't even get to that point. With active sync on as soon as I start the unlocker RUU it gets the info from my phone and shows the current rom 3.14.605.1 ....I click update and it shows 2.31 unlocker I hit next and then the install status bar comes up on my desktop and my phone goes into bootloader mode and the active sync connection drops and I get the 262 connection error. If I start the RUU with my phone in bootloader usb mode already it does not detect my current rom and I click next. click next to 2.31 unlocker, and it goes through the same steps and I get the same error. Is there anything I have to do to my phone prior to running the RUU. My phone is a verizon xv6900 running wm 6.1 rom 3.14.605.1 with radio 3.37.78
I have the same problem with my new sprint touch. I get error 262 at 0%, did they change something in these new phone that won't allow us to unlock?
Rom is 3.03.651.4
radio 3.42.30
I think I got it, what I did was not to extract the vogue_unlocker_MFG_2.31.exe file but to run it. I had activesync set up and connected, then just ran the unlocker, don't extract it. It will shut off activesnyc and put my phone in to the 3 color screen, form there, just follow the directions. Also I didn't have to run the exitbl step as my phone auttomatically exit and restarted.
I ended up having to re-run the .041 unlocker and then the 2.31 unlocker and it ended up working for me. I'm not sure why I had to because I Had the same bootloader info prior to running the 2.31 unlocker in the first place. The 6.5 rom and gps rom has been working flawlessly for a week now, the only thing I had to do was call up VZW (*8889) the guy answered "account investigations" LOL I told him I had to hard reset and my phone wouldn't authenticate and he asked me to call back from another line. I told him that I had no landline and he said thats fine I can override it just call back right away whenever you get to another phone. That was on friday and I have not called back but I've been able to text, make and receive calls so I don't think I will unless I have to.
gooney said:
I think I got it, what I did was not to extract the vogue_unlocker_MFG_2.31.exe file but to run it. I had activesync set up and connected, then just ran the unlocker, don't extract it. It will shut off activesnyc and put my phone in to the 3 color screen, form there, just follow the directions. Also I didn't have to run the exitbl step as my phone auttomatically exit and restarted.
Click to expand...
Click to collapse
thank you! i did that and it worked for me.
yeah, it says right in the directions over there to just run the exe it will create a temp folder and run the RUU itself from there
Extracting it and running it will always cause issues
also - Ignore the sleep4.exe or whatever if you encounter it - it is a legacy exe that is called that isnt used anymore, wont affect the unlocking just hit OK through it
Detroit Doug
Related
PLEASE ASSIST: I'VE RECENTLY UPGRADED MY CINGULAR/ATT 8525 HERMES UNIT TO WINMOB6 AND NOW CAN'T GET PAST THE INITIAL WINDOWS MOBILE SCREEN WHERE IT SAYS "TAP THE SCREEN TO SET UP YOUR WINDOWS MOBILE BASED DEVICE." (THE TOUCHSCREEN SEEMS TO BE DISABLED) ALSO, NOW ACTIVESYNC WILL NOT CONNECT TO THE DEVICE. I'M AT A LOSS AS TO WHAT ELSE TO DO (TRIED HARD RESET SEVERAL TIMES WITH SAME RESULT). IF SOMEONE COULD POINT ME IN THE RIGHT DIRECTION - I'D SURE APPRECIATE IT.
ETUMON said:
PLEASE ASSIST: I'VE RECENTLY UPGRADED MY CINGULAR/ATT 8525 HERMES UNIT TO WINMOB6 AND NOW CAN'T GET PAST THE INITIAL WINDOWS MOBILE SCREEN WHERE IT SAYS "TAP THE SCREEN TO SET UP YOUR WINDOWS MOBILE BASED DEVICE." (THE TOUCHSCREEN SEEMS TO BE DISABLED) ALSO, NOW ACTIVESYNC WILL NOT CONNECT TO THE DEVICE. I'M AT A LOSS AS TO WHAT ELSE TO DO (TRIED HARD RESET SEVERAL TIMES WITH SAME RESULT). IF SOMEONE COULD POINT ME IN THE RIGHT DIRECTION - I'D SURE APPRECIATE IT.
Click to expand...
Click to collapse
hmm no need to scream.
Push the OK on left and power on right, and stick stylus in all at the same time. Re run the exe file while it is plugged in to active sync, and see. Which WM6 did you use?
Sorry I'm new at this. I used WM6.1. Which exe file do you want me to re-run. ActiveSync is offline....I can't get it to connect to the unit. Thanks for your assistance.
ETUMON said:
Sorry I'm new at this. I used WM6.1. Which exe file do you want me to re-run. ActiveSync is offline....I can't get it to connect to the unit. Thanks for your assistance.
Click to expand...
Click to collapse
Ok, since you're on ATT I suggest you follow my instruction above, get into tricolour screen (bootloader), and download this
from the post above you will get the shipped ATT rom. Don't worry if activesync is saying is not connected, just run the file. You will then get back to a WM6.
The phone originally came with WM5 and I was upgrading to mess around with the thing. I'm at the tricoloured screen and now downloading the files from RapidShare. Will this get me back to WM5 or to the upgrade. If there is a way, I like to try the HardSPL flash I've been reading about today - will this work on either WM version? Txs & Rgds.
ETUMON said:
The phone originally came with WM5 and I was upgrading to mess around with the thing. I'm at the tricoloured screen and now downloading the files from RapidShare. Will this get me back to WM5 or to the upgrade. If there is a way, I like to try the HardSPL flash I've been reading about today - will this work on either WM version? Txs & Rgds.
Click to expand...
Click to collapse
After you have flashed this WM6.0 you really need to flash hard SPL first, I thought you would have done that already.
Really please read this first before you brick your phone.
No that's the thing. I'm just finding out how I went about this all wrong and maybe shouldn't have been messing this in the first place. Anyhow, my bootloader screen reads like this:
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
ETUMON said:
No that's the thing. I'm just finding out how I went about this all wrong and maybe shouldn't have been messing this in the first place. Anyhow, my bootloader screen reads like this:
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
Click to expand...
Click to collapse
Well follow mrvanx guide, that's all I had to get on with few months ago.
Many thanks for the advice. So just to be clear I should first run the file I downloaded from RapidShare to get me back to a working WM version, then follow mrvanx guide to flash Hard SPL or viceversa...
ETUMON said:
Many thanks for the advice. So just to be clear I should first run the file I downloaded from RapidShare to get me back to a working WM version, then follow mrvanx guide to flash Hard SPL or viceversa...
Click to expand...
Click to collapse
I have not tried to hardspl a non working phone sorry so I have no experience with that. Give it a go first, and report back.
Still Stuck
zocster said:
I have not tried to hardspl a non working phone sorry so I have no experience with that. Give it a go first, and report back.
Click to expand...
Click to collapse
Nope, didn't work. Here's the report:
ERROR [260]: UPDATE ERROR
The update utility cannot connect to your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA phone.
Check the following:
1. The PDA Phone is connected to the USB cradle/cable.
2. The USB cradle/cable is connected to the PC.
Is there another way to establish comunication with the PDA other than through ActiveSync? Somekind of emulator box or binary software???
ETUMON said:
Nope, didn't work. Here's the report:
ERROR [260]: UPDATE ERROR
The update utility cannot connect to your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA phone.
Check the following:
1. The PDA Phone is connected to the USB cradle/cable.
2. The USB cradle/cable is connected to the PC.
Is there another way to establish comunication with the PDA other than through ActiveSync? Somekind of emulator box or binary software???
Click to expand...
Click to collapse
hmm weird, so have you got .net framework installed on your PC? try it again one more time while in bootloader, plug the phone to USB as long as you can hear the 'ding' sound you should be OK. I have 'bricked' my phone a few times and this always work. What are you trying to flash? the hardspl or the ROM?
Yes, today I upgraded to .net framework 3.5 when ActiveSync failed Microsoft Error took me to their website and offered me the option. I had been running 2.x .net framework and never had a problem would also use same ActiveSync with my old Axim X30.
Yes, I can hear the 'ding' sound and I was trying to run the file RUUWrapper.exe (Hermes ROM Upgrade w/ the option Force using SSPL).
well that shows the other way around doesn't work, so you need to get your phone to a working WM6 state, how is your download going from rapidshare? get it to boot loader mode again and flash that exe file.
Just completed that route - I ran the PDA Phone ROM Update Utility 3.12.3.7 - the process took about 10 minutes to go through 100%, then it restarted and stayed at the Window Mobile screen for little over minute (crossing my fingers), but then just showed the same message "Tap the screen to set up your Window Mobile based device." Please let me know if you have other avenues to try – It’s close to 4am here in Miami, but I'm not sleeping. I’m really glad you are able to assist with this mess – thanks a lot!
ETUMON said:
Just completed that route - I ran the PDA Phone ROM Update Utility 3.12.3.7 - the process took about 10 minutes to go through 100%, then it restarted and stayed at the Window Mobile screen for little over minute (crossing my fingers), but then just showed the same message "Tap the screen to set up your Window Mobile based device." Please let me know if you have other avenues to try – It’s close to 4am here in Miami, but I'm not sleeping. I’m really glad you are able to assist with this mess – thanks a lot!
Click to expand...
Click to collapse
so did you follow it through? and it didn't fix it? you have some bad blocks?
Unfortunately, you need to have some sleep, and read these when you wake up
http://forum.xda-developers.com/showthread.php?t=296722
http://forum.xda-developers.com/showthread.php?t=369434
zocster said:
so did you follow it through? and it didn't fix it? you have some bad blocks?
Unfortunately, you need to have some sleep, and read these when you wake up
http://forum.xda-developers.com/showthread.php?t=296722
http://forum.xda-developers.com/showthread.php?t=369434
Click to expand...
Click to collapse
what does bad blocks mean?
Okay, looks like I've got a Type 2c Brick Situation in my hands.... I think I will take your advice and get some rest and tackle this again later on. I really appreciate your assistance - will you be around again later?
Okay good day, I'm back on the trail. Found shipped ROM on WIKI for HERMES in the following thread - http://forum.xda-developers.com/showthread.php?t=277664
Downloading now...According to pof(moderator) it's a "new rom from the still unreleased Cingular 8525: HTC Hermes (HERM100) branded from U.S. Operator Cingular"
My only question then would be that this appears to be made for WM5 and I performed the WM6 upgrade which is what got me into this mess in the first place - so will there be any conflicts or issues I should now about? I'm about to go ahead with it - if anyone is out there and thinks otherwise, please advise soonest. Thx & rgds, Ed
ETUMON said:
Okay good day, I'm back on the trail. Found shipped ROM on WIKI for HERMES in the following thread - http://forum.xda-developers.com/showthread.php?t=277664
Downloading now...According to pof(moderator) it's a "new rom from the still unreleased Cingular 8525: HTC Hermes (HERM100) branded from U.S. Operator Cingular"
My only question then would be that this appears to be made for WM5 and I performed the WM6 upgrade which is what got me into this mess in the first place - so will there be any conflicts or issues I should now about? I'm about to go ahead with it - if anyone is out there and thinks otherwise, please advise soonest. Thx & rgds, Ed
Click to expand...
Click to collapse
Sounds good man!! Flash it!! oem WM6 roms usually fix allot of issues.. Don't be scared everyone else is busy flashing WM6.1 roms all the time now!
Thanks for the words of support <joshkoss>! Just attempted several times to flash the Shipped ROM I found from <pof> (PDA Phone ROM Update Utility - R:31300 D:51000 U:31101 P:0) and keep getting ‘ERROR[260]: UPDATE ERROR’ message. While instead I went back again to flashing the ROM that <zocster> suggested last night (PDA Phone ROM Update Utility 3.12.3.7) and it does go through the entire 10 minute process until it shows 100% completion both on the PDA and on the PC and then tells me congratulations….etc. I even flashed it twice back-to-back as I read to do in one of the threads – but just keep getting back to the dreaded Window Mobile screen with the same message "Tap the screen to set up your Window Mobile based device."
My next question is this: Why does the PDA Phone ROM Update Utility 3.12.3.7 connect to the PDA, but the PDA Phone ROM Update Utility - R:31300 D:51000 U:31101 P:0 (which I read is the Shipped ROM that I need to get the PDA back to) gives me an error message. Obviously, there is a connection since I’m able to get a 100% completion on the other ROM??? Please kindly advise…..
i have a custom rom with a 3.42 radio and wm 6.1
if i upgrade my phone to windows mobile 6.5 will i still have my custom rom or would it be all new just like when you flash a new rom?
jljohnson919 said:
i have a custom rom with a 3.42 radio and wm 6.1
if i upgrade my phone to windows mobile 6.5 will i still have my custom rom or would it be all new just like when you flash a new rom?
Click to expand...
Click to collapse
The only way you would be able to upgrade to WinMO 6.5 would be to flash the phone just like when you flash a custom ROM now
WinMO 6.5 is not an installable app/upgrade like upgrading an application on your phone its the operating system itself
Right now and there are very few ROMS out there for WinMO 6.5 and none for the Vogue at all (Im assuming you have a Vogue as this is where you posted) soon there will be one as there are people working on it currently but what is there is EXTREMELY buggy and almost non-functional for the fact its on a phone and a phone should be able to be used after all LOL
Keep with the Custom ROMS for now and wait, the desire for it has been spoken and the Chefs are a cookin LOL
Detroit Doug
NFSFan has confirmed that those WM 6.5 ROMS are FAKE. Even if they were real, there would be no point of using them...
The builds are fake indeed. However they do contain a few components of 6.5. None which are worth upgrading for.
NFSFAN said:
The builds are fake indeed. However they do contain a few components of 6.5. None which are worth upgrading for.
Click to expand...
Click to collapse
Really? What components do they have? Anything from a new today screen or Internet Explorer (like rumored)?
Kinetic scroll (give up TouchFLO and Manila2D), new IE build that supports kinetic scroll. The today screens being posted are fake. They are actually from a smartphone, called HTC Juno. Some asian dude took it out of the Juno, resized the images, and re-arranged the tabs to make it look like the new today screen.
flashing on Vouge
I know this may sound tedious but i have no idea on how to flash any ROM onto my Vouge. Can someone please help. I would love to try out several ROMs and see which one would work best for me.
Thanks in advance
Hey, here is one really good one
Detroit_Doug said:
Basically here are the steps
Download the 2.31 unlocker
Download the ROM you want to use (my personal preference is this one for a TF2D style or this one for a WinMO 6.5 style interface that has TF2D included to switch back and for - both very stable, fast and clean and the thread is very active for help (especially if your on Verizon or Bell which can have issues)
from there, use WinRAR to extract each file into separate folders
then Put your phone in bootloader mode (press and hold power+camera+stylus in reset until 3-color screen comes up)
At this point at the bottom of the screen it will say Serial, plug it into the USB cable or cradle and it should change to USB
Start the exe in the 2.31 and follow the directions (you may get some errors about sleep4.exe just click on OK as it keeps occuring its a XP/Windows7 64 bit issue if that is what your using)
At the point where it tell you to disconect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
once complete, reboot, allow it to do its thing then reboot and go back into bootloader again during reboot you should see coke 2.31 in the upper left if so your ready to go
plug it into your USB/Cradle again and then go into the ROM folder you extracted the ROM into
Once the screen on your phone says USB again go to the folder and double click on the RomUpdateUtility.exe file and follow the directions again, it may take some time so be paitent
once the phone flashes and reboots, let it run and do its thing to the and reboot itself then (and here is an important step for stability) once it starts up do a hard reset (red+green+stylus in reset hole) hit the enter button (center of D-Pad) it will reflash the phone and then red key (send) when prompted
then go thought the setup again, this time you can actually set things up as your keeping them this time and once things are done and your at the start screen on your phone power off (not reset) the phone and then start it up again - seems doing it this way takes care of alot of little issues that will come up before they can happen
Depending on your carrier be sure to have one of the DCD Carrier Cabs as well especially for the 6.5 ROM as it is a generic ROM and some have reported needing to run the DCD Carrier Cab for the service they use to get on the internet and use GPS and the like
Detroit Doug
Click to expand...
Click to collapse
thanks
Everything is working smoothly and better than I thought it would have (i flashed the 6.5 ROM). Thanks to you Detroit Doug or I don't think I would have been able to do it without your instructions. I however do have one more question....i'm having issues syncing the device with my PC now. Any idea on what that could be???
re: Thanks
I've done several resets but to no avail am i able to connect via active sync???
OK maybe i lied about everything working properly and wonderful....so on top of not being able to connect to my PC via activesync I also am not able to connect to the internet on my device, i've downloaded and installed the NFSFAN Sprint GPS Registry but still its a no go... Did i do something wrong completely????? still
I fixed the internet problem!!!!!!!!!!!!!!!!!!!!
....somehow magically i'm now able to connect via activesync. I guess the device just needed time to adjust. Thanks for the help, and i do apologize for the numerous newbie questions.
ehepps said:
....somehow magically i'm now able to connect via activesync. I guess the device just needed time to adjust. Thanks for the help, and i do apologize for the numerous newbie questions.
Click to expand...
Click to collapse
ok so i didnt notice this thread. so whats your secret? howd you get it to work?
mbaseball, I just replied to your thread.
MMS
I flashed the rom perfectly and im lovin every thing bout it but one thing, i cant send or recieve picture mail. Is there a way 2 fix that or sumthin. That takes alot of funny away from the rom. help me please. does there happen to be a 6.5 rom wit picture mail?
Best Windows Mobile 6.5 upgrade for Vogue (Bell)?
hi
I 've been reading this thread, and am just wondering whats' the best download so far for upgrading to Windows Mobile 6.5, for HTC Touch - I think this is the vogue...for Bell Mobility?
If you could please provide a download link.
Thank you all for your help
Thank you
Karim
kchaggani said:
hi
I 've been reading this thread, and am just wondering whats' the best download so far for upgrading to Windows Mobile 6.5, for HTC Touch - I think this is the vogue...for Bell Mobility?
If you could please provide a download link.
Thank you all for your help
Thank you
Karim
Click to expand...
Click to collapse
The best is NFSFAN's Windows Mobile 6.5 ROM. You can find it on another thread in this forum right here:
http://forum.xda-developers.com/showthread.php?t=432487
Don’t even bother with anything else. I am running this. It is fast, stable and very close to the stock WM 6.5 (I have downloaded the device emulator image from Microsoft’s website for software development purposes). The extras that are in there are useful.
The Fish
i dont want to be a pain in the ass can someone link me a tutorial on how to flash roms im very intrested into flashing to a 6.5 rom will read up myself just cant find a stright up tutorial tyia guys btw have a sprint htc touch
ohthebaby said:
i dont want to be a pain in the ass can someone link me a tutorial on how to flash roms im very intrested into flashing to a 6.5 rom will read up myself just cant find a stright up tutorial tyia guys btw have a sprint htc touch
Click to expand...
Click to collapse
OK, as I have a Sprint Touch as well... Here goes...
First go HERE and READ the hell outta it until you have it step by step (BTW use the 2.31 unlocker regardless about the GPS thing)
OK, now that youve read that (happy dance time)
Download the 2.31 Unlocker and a WinMO 6.5 ROM personally I suggest this ONE as it is one I use
And make sure to download the DCD Sprint Carrier cab and copy it to your SD card as you may need this after the flashing is done (will get back to this tasty morsel later)
OK, now you have an Unlocker and a ROM - now what, hmmmm
Use WinRAR and extract both the files into separate folders
Press and hold the Power button+Camera Button and Stylus in the reset hole until the 3 color screen comes up and it says serial, now plug in your cable and it should change to USB
can you taste the rainbow and it is over the land of USB?? great, now go into the Unlocker folder you created and doubleclick on the RomUpdateUtility.exe (going to be called RUU.exe from this point on)
Follow the steps on the desktop monitor (you might get some errors about sleep4.exe - dont worry about it, just keep hitting enter and it will go away after the 4th or so time
At some point the program is going to tell you to disconnect the phone, sounds scarey doesnt it, losing the connection and all - dont be, be a brave little soldier and disconnect it and count to 10, cant do that, get some help in getting there, its really that important LOL once you (or your friend) gets to 10 plug it back in, does it say USB again? good!! happy dance AFTER you hit a key on the keyboard per the on screen directions
its going to eventually reboot, let it and it will be unlocked, let it start up and do its thing, when its done - go ahead and go back into bootloader mode again (remember power+camera+stylus twister move you did earlier, its back to that again) with the cable disconnected and it had better say SERIAL again.. now go ahead and plug in the cable and it should change to USB
Now go into the ROM folder and double click the RUU.exe here ... and follow the directions that come up on the screen...
Once its done and the phone reboots, wait... wait some more.. still keep waiting.. no not yet ... stop touching it.. it wont help pacing.. just be patient... oh look an Orange screen, ok here comes some fun
Follow the drections to go through the setup, dont worry about it being to accurate and all as it is about to be erased anyway... let the autorun happen once windows starts and it will reboot on its own again - yes it really IS a smartphone isnt it LOL
OK, as it is booting up again when there is a black screen - press and hold the red button+green button+stylus in reset hole (known as a Hard reset) until the screen turns gray - follow the directions again (save you some time "press the Enter key" thats the big silver button in the center of the buttons LOL) and when the progress bar moves all the way to the right, press the end key (the green one)
Again, it will restart (told you it was smart) and now go ahead and do the setup and customizations and do them right this time as your hanging onto them this time (sounds weird but if you dont hard reset after flashing it flying monkeys will swoop in and take your phone and your little dog toto too)
OK, now remember that DCD Sprint Carrier Cab, you do, fantastic .. so to the storage card where you copied it to - you didnt forget that step did you??? good I knew my faith in you would pay off, tap on it and run it - it will install all the Sprint goodies to make your life easy, and your sex life better and even improve that certain area of a .. wait sorry wrong channel again.... just go ahead and tap it, run it and reboot
now you have a Sprint 6.5 Custom ROM
Enjoy
Detroit Doug
dude f****** grt lol wow thats a tutorial and a half ty ima try it now
Detroit_Doug,
In NFS Fan's v 6.5 ROM, which GPS registry cab should I use for MetroPCS?
Also, is it true that MMS is not supported on this ROM version?
Will this update my radio to the latest version (Radio version 3.42.30) so that GPS is enabled? I was having GPS issues on the latest Sprint stock ROM after flashing to Metro.
awesome, thank you! heheh, flying monkeys.
anithinks said:
Detroit_Doug,
In NFS Fan's v 6.5 ROM, which GPS registry cab should I use for MetroPCS?
Also, is it true that MMS is not supported on this ROM version?
Will this update my radio to the latest version (Radio version 3.42.30) so that GPS is enabled? I was having GPS issues on the latest Sprint stock ROM after flashing to Metro.
Click to expand...
Click to collapse
Yes MMS IS supported on the ROM, but per some steps and depending on your Provider, well that can be the tricky part as they can be a PITA at times
As far as MetroPCS - I really dont know, I personally go to the thread of MFSFANs ROM and do a search through it for MetroPCS (there are a few of you trying to take over the world - I aint skeered though) but there is some info there, I just cant remember every carrier and every issues for every phone - I have my own plans on taking over the world as well you know (are ya skeered???) come on pinky, time to put my plan into action
Detroit Doug
EDIT: Here is the link for MetroPCS - its for the Titan, but ask the person that started the thread - the cab shouldnt matter as it is provisioning data and the like - again ask the posted on the thread, I dont know anything about it - simple search found this as well
http://forum.xda-developers.com/showthread.php?p=3609082#post3609082
could you find the one for USCC & what does the cab do?
Viper Matrix Wireless said:
could you find the one for USCC & what does the cab do?
Click to expand...
Click to collapse
If your referring to "what does a carrier cab do" it installs various settings and progs and provisioning data to help you connect to your network for phone, data, internet, GPS, aGPS, etc
As far as finding it - search can be your friend - I dont even know if there is one for USCC or MetroPCS - find whatever carrier is similar/compatible and use it
Detroit Doug
EDIT - amazing a search for USCC Carrier CAB found lots of posts - 5th post through and the preview gave the link you need directly
http://sites.google.com/site/victorbush/htc-6800-1/epst-data-settings
Good afternoon everyone.
So I took a leap and tried to flash my alltel htc vogue to wm 6.5. I'll give the basics of what i did. so here we go.
1. I CID unlocked the phone using the vogue unlocker tool. the spl is currently looks like this
VOGU100
SPL-0.41.CoKe
CPLD-3.
now after that, i ran the following RUU update NagROM V3.13 Touch. Everything looks to go great and the phone will work ( aside from the internet because I don't know the number to set up the connection, and the camera doesn't seem to work but i'm ok with that ) until you unplug the usb cable from the phone. 3-5 seconds after you unplug it, it reboots and stays in a boot loop until you plug the usb cable back in. I'm pretty much at a loss here, so any assistance would be greatly appreciated. if anyone feels so inclined to add me to their msn or shoot me an email, it's [email protected]. And yes i've searched all over the site for assistance before posting.
Update: i think it has something to do with my bootloader, at least that's what i gather from other posts around the internet. how do i fix this? taking it back to the original bootloader or what?
reb0rn1 said:
Good afternoon everyone.
So I took a leap and tried to flash my alltel htc vogue to wm 6.5. I'll give the basics of what i did. so here we go.
1. I CID unlocked the phone using the vogue unlocker tool. the spl is currently looks like this
VOGU100
SPL-0.41.CoKe
CPLD-3.
now after that, i ran the following RUU update NagROM V3.13 Touch. Everything looks to go great and the phone will work ( aside from the internet because I don't know the number to set up the connection, and the camera doesn't seem to work but i'm ok with that ) until you unplug the usb cable from the phone. 3-5 seconds after you unplug it, it reboots and stays in a boot loop until you plug the usb cable back in. I'm pretty much at a loss here, so any assistance would be greatly appreciated. if anyone feels so inclined to add me to their msn or shoot me an email, it's [email protected]. And yes i've searched all over the site for assistance before posting.
Click to expand...
Click to collapse
I'm not sure if this is the only problem, but I think you used the wrong unlocker. You need 2.31 since Nag's ROM is gps capable. See this post for more background and the correct unlocker:
http://forum.ppcgeeks.com/showthread.php?t=20370
Hope this helps!
well since using nag's i've tried another ROM, T2_V2.2 (based on Mega M2d Test2 and SYS 23016.updated 10.14.09), that one i really like, and i dunno if my phone supports gps or not, maybe that could be why it reboots when i unhook the usb cable? if that's the case how do i, a) reverse the bootloader change, b) go back to an original rom and start from scratch?
uh oh.
you used the wrong unlocker. i did that same thing too.
http://forum.ppcgeeks.com/showthread.php?t=91101&page=4
USE THAT the post is there. ali3nfr3ak should be helping you. and after you sort it out. USE THE 2.31 UNLOCKER!.
Please save sarcasm when responding. I have been reading and would onlt ask for help a last option.
My phone - HTC Pro 2 (I bought it from a authorized t-mobile store)
Need help with - ugrading it to 6.5 or any cooked version that will work
History - my phone is already unlocked as I had unlock kings do it. I tested it and I can put any sim it and it works fine.
Problem - every time I try and install a new rom on it I get one the follwing errors or issues: My usb connection stop when the install starts and the process times out, or I get a host of errors messeges from invild device to wrong version.
I need very simple instructions on what I need to do upgrade my os and then later migrate to some of the really roms I have seen on this site.
Please help.
Did you hardSPL? If not go here: HardSPL
Nothing
I DL'ed the fle and followed directions (auto option). Nothing happened.
bigdaddy67 said:
I DL'ed the fle and followed directions (auto option). Nothing happened.
Click to expand...
Click to collapse
When you read those 11 steps in the HSPL thread, where is it, where you say: nothing happends?
As it stands, you will only be able to install an official T-Mobile ROM if it is a T-Mobile-branded phone.
So installing HardSPL will let you flash whatever ROM you want, any of the official ones (including, say, HTC official 6.5), or one of the fine cooked ones from this forum.
If you are having trouble with HardSPL, you really need to post on that in the HardSPL sticky.
no matter what I do, the connection always times out. It seems my phone will not allow anything rom software to be installed. Where can I find enableapnew.cab? The rom software told me i needed that.
@bigdaddy67
This sounds like a USB issue, try this:
1. Power off your TP2
2. Press and HOLD the volume down button, press and HOLD power button until you see the multi-coloured screen (bootloader mode)
3. Connect your TP2 to your computer via USB
4. You should now see the letters USB at the bottom of the TP2 screen
5. If you DO, run hardSPL
If you DON'T, try a different USB cable and/or port on your computer.
If none of the above helps, take a screen shot of your bootloader screen and post it.
How to get a screenshot:
1. Go to http://www.mymobiler.com and download/install the software.
2. Open it and take a screen shot
3. Post it here.
We are here to help, but need some additional details!!!
Russ
bigdaddy67 said:
no matter what I do, the connection always times out. It seems my phone will not allow anything rom software to be installed. Where can I find enableapnew.cab? The rom software told me i needed that.
Click to expand...
Click to collapse
normally I would tell you to go search but you seem to be in a pickle so here...
Russ
bigdaddy67 said:
Please save sarcasm when responding. I have been reading and would onlt ask for help a last option.
My phone - HTC Pro 2 (I bought it from a authorized t-mobile store)
Need help with - ugrading it to 6.5 or any cooked version that will work
History - my phone is already unlocked as I had unlock kings do it. I tested it and I can put any sim it and it works fine.
Problem - every time I try and install a new rom on it I get one the follwing errors or issues: My usb connection stop when the install starts and the process times out, or I get a host of errors messeges from invild device to wrong version.
I need very simple instructions on what I need to do upgrade my os and then later migrate to some of the really roms I have seen on this site.
Please help.
Click to expand...
Click to collapse
Welcome to forums
Hope this guide help you:
http://forum.xda-developers.com/showthread.php?t=550540
And don´t forget to vote!
bigdaddy67 said:
no matter what I do, the connection always times out. It seems my phone will not allow anything rom software to be installed. Where can I find enableapnew.cab? The rom software told me i needed that.
Click to expand...
Click to collapse
Also, which OS are you running on your PC? If its Windows XP, make sure you download Active Sync and install/run it. If you run Vista / 7, make sure you run the Mobile Device Center.
moved you're thread out of rom dev section, best of luck sir.
Update -
My OS is win xp and copied and installed the cab on my device. then I re-powered hold down the volume and got that tri-color screen with the usb connected. Started the HardSP app and have been waiting for 15 minutes as nothing seems to be working.
Did I miss something?
Got error 262
Ok I finally got an 262 error. I am not what I missed. Dl'ed the cab re-powered holding down vol key started HardSp app.
Help.
Stil need help
I am at home and my pc is vista. Can someone pls help get over this hurdle?
Please Please Please