Related
PLEASE HELP ME
I tried to upgrade my xda exec rom from the O2 updates website, the process went smoothly until my pc told me to do the cold reboot on the phone. However after doing this reboot my screen looks like it has crashed and just a coloured mess fills the screen. my pc cannot see the phone now. is it possible to put the original software on the rom and if so how do i do it?
PLEASE HELP, ANYONE.... I feel like O2 have given dodgy info on their downloads
I have a same problem like u. I try to upgrade rom to version v1.30.162 on http://www.my-xda.com/xdaExecSoftware.jsp, but afer that my exec stuck on bootloader and can't recognize USB port only serial port. And i try to send back my exec to O2 and ask what happen to my phone, customer service said that i upgrade using uncompatible ROM for Exec, but i think i use an original ROM from O2.
Put the device into bootloader by pressing and holding the backlight key, power key and reset button at the same time for 3 seconds. If you see serial in the display, hook it up to the PC. The display will change to read usb. Windows will whinge and ***** that the usb device is not recognised, ignore this, it is normal. Take this opportunity to flash a decent ROM, not the crap standard ones. If you do want to use a standard ROM, download them from the FTP. I have downloaded corrupt ROMs from O2 in the past.
@Willows, try using a different USB port, sounds daft but happened quite often on the Alpine. You never know......
Just to add to Pug's answer. If your next question is how to upgrade, follow this thread: http://forum.xda-developers.com/showthread.php?t=269118
cktlcmd said:
Just to add to Pug's answer. If your next question is how to upgrade, follow this thread: http://forum.xda-developers.com/showthread.php?t=269118
Click to expand...
Click to collapse
Watching my back when I'm drink surfing now?
There's always something you forget isn't there.
Thank you.
pug said:
Watching my back when I'm drink surfing now?
There's always something you forget isn't there.
Thank you.
Click to expand...
Click to collapse
All the stuff I am learning from WM5 I read from here just lurking around. Just returning them to others. I should be thanking you too. So thank you.
where can i get the upgrade
hi, can anyone supply me with a link to get an O2 xda exec rom upgrade as i downloaded and installed the version from the O2 site and it caused my phone to go into meltdown.
Please help
Thanks in advance.
IT WORKS But....
pug said:
Put the device into bootloader by pressing and holding the backlight key, power key and reset button at the same time for 3 seconds. If you see serial in the display, hook it up to the PC. The display will change to read usb. Windows will whinge and ***** that the usb device is not recognised, ignore this, it is normal. Take this opportunity to flash a decent ROM, not the crap standard ones. If you do want to use a standard ROM, download them from the FTP. I have downloaded corrupt ROMs from O2 in the past.
@Willows, try using a different USB port, sounds daft but happened quite often on the Alpine. You never know......
Click to expand...
Click to collapse
I did what you said and my phone is up and running again, however I have a new problem now.
I have TomTom 5 on my xda exec with an BT GPS Bluetooth sat ariel. Before hand the device worked perfectly but now TomTom cannot see the device, I have re-installed all the software and set up my Com ports and enabled Bluetooth.
Has anyone got any ideas?
scousegitt said:
hi, can anyone supply me with a link to get an O2 xda exec rom upgrade as i downloaded and installed the version from the O2 site and it caused my phone to go into meltdown.
Please help
Thanks in advance.
Click to expand...
Click to collapse
Just re-flash it, it's the only way to be sure:
ftp://xda:[email protected]/Uploads/Universal/Shipped_ROMs/Xda_Exec_Upgrade_v1.30.162.exe
Make a backup of your contacts first though.....
EDIT:
Forgot to mention, when using BT GPS, do not set up the COM ports with secure connections, the UNI doesn't like it.
Still no joy
pug said:
Just re-flash it, it's the only way to be sure:
ftp://xda:[email protected]/Uploads/Universal/Shipped_ROMs/Xda_Exec_Upgrade_v1.30.162.exe
Make a backup of your contacts first though.....
EDIT:
Forgot to mention, when using BT GPS, do not set up the COM ports with secure connections, the UNI doesn't like it.
Click to expand...
Click to collapse
I have re-flashed again and installed tomtom 5 but still can't get the xda to communicate with the BT GPS FGPXBT02 the bluetooth is connected and the com ports set up with no security but tomtom still reports no GPS device found. Could anythin else be wrong?
Tom Tom 5 will not work under WM5. Go to ToTom site, and there is a 5.2 upgrade, which works fine
i dont know what's wrong, ive owned this dash since march. updated to wm6 when it came out, then stopped giving a hoot after finding out that SNappunlock wont work on my dash.
i noticed people here found a very nice dash rom that i want to flash to so badly, but i learned that this requires appunlock in order to get the CID bypass to work
after searching around for wm5 (took about an hour) so i can flash back just so i can appunlock, then flash to the better rom. i found it! all thanks to BGNiko
you think i'm done with my problems, right? well i go to flash to wm5, and during the flashing session, the screen brings me to that RGB before the rom change happens, but no go! it tells me my usb cable isnt hooked up even though it is. ive had no problems re-flashing to the wm6, so the cable isnt the problem.
anyone ever have problems reverting to wm5? is there a solution?
thanks in advance
ps: i have us tmobile
uhh... did you try again?
i had the same thing happen to me. tried again, same thing (same message that you got). restarted the computer, tried again... presto. worked fine.
so long as the flash process doesn't start, your phone should be fine. it's just a matter of getting the computer to talk to the phone. it might be as simple as a computer restart... or trying a differnt usb port or something.
well, took your advise.. didnt work, but thats because i have vista (go figure). did it on my other comp and it worked
though i'm still faced with the appunlock problem
appunlock didnt work, and every time i go to execute sda unlock it tells me that its "not a certified windows CE edition"? or something to that matter
any help would be greatly appreciated
edit: wow, so i am an idiot. i thought the apps had to be excecuted from the phone.
anyway, did the uspl cid unlock. turned my screen white instead of black, but i'll take it
PLEASE ASSIST: I'VE RECENTLY UPGRADED MY CINGULAR/ATT 8525 HERMES UNIT TO WINMOB6 AND NOW CAN'T GET PAST THE INITIAL WINDOWS MOBILE SCREEN WHERE IT SAYS "TAP THE SCREEN TO SET UP YOUR WINDOWS MOBILE BASED DEVICE." (THE TOUCHSCREEN SEEMS TO BE DISABLED) ALSO, NOW ACTIVESYNC WILL NOT CONNECT TO THE DEVICE. I'M AT A LOSS AS TO WHAT ELSE TO DO (TRIED HARD RESET SEVERAL TIMES WITH SAME RESULT). IF SOMEONE COULD POINT ME IN THE RIGHT DIRECTION - I'D SURE APPRECIATE IT.
ETUMON said:
PLEASE ASSIST: I'VE RECENTLY UPGRADED MY CINGULAR/ATT 8525 HERMES UNIT TO WINMOB6 AND NOW CAN'T GET PAST THE INITIAL WINDOWS MOBILE SCREEN WHERE IT SAYS "TAP THE SCREEN TO SET UP YOUR WINDOWS MOBILE BASED DEVICE." (THE TOUCHSCREEN SEEMS TO BE DISABLED) ALSO, NOW ACTIVESYNC WILL NOT CONNECT TO THE DEVICE. I'M AT A LOSS AS TO WHAT ELSE TO DO (TRIED HARD RESET SEVERAL TIMES WITH SAME RESULT). IF SOMEONE COULD POINT ME IN THE RIGHT DIRECTION - I'D SURE APPRECIATE IT.
Click to expand...
Click to collapse
hmm no need to scream.
Push the OK on left and power on right, and stick stylus in all at the same time. Re run the exe file while it is plugged in to active sync, and see. Which WM6 did you use?
Sorry I'm new at this. I used WM6.1. Which exe file do you want me to re-run. ActiveSync is offline....I can't get it to connect to the unit. Thanks for your assistance.
ETUMON said:
Sorry I'm new at this. I used WM6.1. Which exe file do you want me to re-run. ActiveSync is offline....I can't get it to connect to the unit. Thanks for your assistance.
Click to expand...
Click to collapse
Ok, since you're on ATT I suggest you follow my instruction above, get into tricolour screen (bootloader), and download this
from the post above you will get the shipped ATT rom. Don't worry if activesync is saying is not connected, just run the file. You will then get back to a WM6.
The phone originally came with WM5 and I was upgrading to mess around with the thing. I'm at the tricoloured screen and now downloading the files from RapidShare. Will this get me back to WM5 or to the upgrade. If there is a way, I like to try the HardSPL flash I've been reading about today - will this work on either WM version? Txs & Rgds.
ETUMON said:
The phone originally came with WM5 and I was upgrading to mess around with the thing. I'm at the tricoloured screen and now downloading the files from RapidShare. Will this get me back to WM5 or to the upgrade. If there is a way, I like to try the HardSPL flash I've been reading about today - will this work on either WM version? Txs & Rgds.
Click to expand...
Click to collapse
After you have flashed this WM6.0 you really need to flash hard SPL first, I thought you would have done that already.
Really please read this first before you brick your phone.
No that's the thing. I'm just finding out how I went about this all wrong and maybe shouldn't have been messing this in the first place. Anyhow, my bootloader screen reads like this:
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
ETUMON said:
No that's the thing. I'm just finding out how I went about this all wrong and maybe shouldn't have been messing this in the first place. Anyhow, my bootloader screen reads like this:
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
Click to expand...
Click to collapse
Well follow mrvanx guide, that's all I had to get on with few months ago.
Many thanks for the advice. So just to be clear I should first run the file I downloaded from RapidShare to get me back to a working WM version, then follow mrvanx guide to flash Hard SPL or viceversa...
ETUMON said:
Many thanks for the advice. So just to be clear I should first run the file I downloaded from RapidShare to get me back to a working WM version, then follow mrvanx guide to flash Hard SPL or viceversa...
Click to expand...
Click to collapse
I have not tried to hardspl a non working phone sorry so I have no experience with that. Give it a go first, and report back.
Still Stuck
zocster said:
I have not tried to hardspl a non working phone sorry so I have no experience with that. Give it a go first, and report back.
Click to expand...
Click to collapse
Nope, didn't work. Here's the report:
ERROR [260]: UPDATE ERROR
The update utility cannot connect to your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA phone.
Check the following:
1. The PDA Phone is connected to the USB cradle/cable.
2. The USB cradle/cable is connected to the PC.
Is there another way to establish comunication with the PDA other than through ActiveSync? Somekind of emulator box or binary software???
ETUMON said:
Nope, didn't work. Here's the report:
ERROR [260]: UPDATE ERROR
The update utility cannot connect to your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA phone.
Check the following:
1. The PDA Phone is connected to the USB cradle/cable.
2. The USB cradle/cable is connected to the PC.
Is there another way to establish comunication with the PDA other than through ActiveSync? Somekind of emulator box or binary software???
Click to expand...
Click to collapse
hmm weird, so have you got .net framework installed on your PC? try it again one more time while in bootloader, plug the phone to USB as long as you can hear the 'ding' sound you should be OK. I have 'bricked' my phone a few times and this always work. What are you trying to flash? the hardspl or the ROM?
Yes, today I upgraded to .net framework 3.5 when ActiveSync failed Microsoft Error took me to their website and offered me the option. I had been running 2.x .net framework and never had a problem would also use same ActiveSync with my old Axim X30.
Yes, I can hear the 'ding' sound and I was trying to run the file RUUWrapper.exe (Hermes ROM Upgrade w/ the option Force using SSPL).
well that shows the other way around doesn't work, so you need to get your phone to a working WM6 state, how is your download going from rapidshare? get it to boot loader mode again and flash that exe file.
Just completed that route - I ran the PDA Phone ROM Update Utility 3.12.3.7 - the process took about 10 minutes to go through 100%, then it restarted and stayed at the Window Mobile screen for little over minute (crossing my fingers), but then just showed the same message "Tap the screen to set up your Window Mobile based device." Please let me know if you have other avenues to try – It’s close to 4am here in Miami, but I'm not sleeping. I’m really glad you are able to assist with this mess – thanks a lot!
ETUMON said:
Just completed that route - I ran the PDA Phone ROM Update Utility 3.12.3.7 - the process took about 10 minutes to go through 100%, then it restarted and stayed at the Window Mobile screen for little over minute (crossing my fingers), but then just showed the same message "Tap the screen to set up your Window Mobile based device." Please let me know if you have other avenues to try – It’s close to 4am here in Miami, but I'm not sleeping. I’m really glad you are able to assist with this mess – thanks a lot!
Click to expand...
Click to collapse
so did you follow it through? and it didn't fix it? you have some bad blocks?
Unfortunately, you need to have some sleep, and read these when you wake up
http://forum.xda-developers.com/showthread.php?t=296722
http://forum.xda-developers.com/showthread.php?t=369434
zocster said:
so did you follow it through? and it didn't fix it? you have some bad blocks?
Unfortunately, you need to have some sleep, and read these when you wake up
http://forum.xda-developers.com/showthread.php?t=296722
http://forum.xda-developers.com/showthread.php?t=369434
Click to expand...
Click to collapse
what does bad blocks mean?
Okay, looks like I've got a Type 2c Brick Situation in my hands.... I think I will take your advice and get some rest and tackle this again later on. I really appreciate your assistance - will you be around again later?
Okay good day, I'm back on the trail. Found shipped ROM on WIKI for HERMES in the following thread - http://forum.xda-developers.com/showthread.php?t=277664
Downloading now...According to pof(moderator) it's a "new rom from the still unreleased Cingular 8525: HTC Hermes (HERM100) branded from U.S. Operator Cingular"
My only question then would be that this appears to be made for WM5 and I performed the WM6 upgrade which is what got me into this mess in the first place - so will there be any conflicts or issues I should now about? I'm about to go ahead with it - if anyone is out there and thinks otherwise, please advise soonest. Thx & rgds, Ed
ETUMON said:
Okay good day, I'm back on the trail. Found shipped ROM on WIKI for HERMES in the following thread - http://forum.xda-developers.com/showthread.php?t=277664
Downloading now...According to pof(moderator) it's a "new rom from the still unreleased Cingular 8525: HTC Hermes (HERM100) branded from U.S. Operator Cingular"
My only question then would be that this appears to be made for WM5 and I performed the WM6 upgrade which is what got me into this mess in the first place - so will there be any conflicts or issues I should now about? I'm about to go ahead with it - if anyone is out there and thinks otherwise, please advise soonest. Thx & rgds, Ed
Click to expand...
Click to collapse
Sounds good man!! Flash it!! oem WM6 roms usually fix allot of issues.. Don't be scared everyone else is busy flashing WM6.1 roms all the time now!
Thanks for the words of support <joshkoss>! Just attempted several times to flash the Shipped ROM I found from <pof> (PDA Phone ROM Update Utility - R:31300 D:51000 U:31101 P:0) and keep getting ‘ERROR[260]: UPDATE ERROR’ message. While instead I went back again to flashing the ROM that <zocster> suggested last night (PDA Phone ROM Update Utility 3.12.3.7) and it does go through the entire 10 minute process until it shows 100% completion both on the PDA and on the PC and then tells me congratulations….etc. I even flashed it twice back-to-back as I read to do in one of the threads – but just keep getting back to the dreaded Window Mobile screen with the same message "Tap the screen to set up your Window Mobile based device."
My next question is this: Why does the PDA Phone ROM Update Utility 3.12.3.7 connect to the PDA, but the PDA Phone ROM Update Utility - R:31300 D:51000 U:31101 P:0 (which I read is the Shipped ROM that I need to get the PDA back to) gives me an error message. Obviously, there is a connection since I’m able to get a 100% completion on the other ROM??? Please kindly advise…..
i have a custom rom with a 3.42 radio and wm 6.1
if i upgrade my phone to windows mobile 6.5 will i still have my custom rom or would it be all new just like when you flash a new rom?
jljohnson919 said:
i have a custom rom with a 3.42 radio and wm 6.1
if i upgrade my phone to windows mobile 6.5 will i still have my custom rom or would it be all new just like when you flash a new rom?
Click to expand...
Click to collapse
The only way you would be able to upgrade to WinMO 6.5 would be to flash the phone just like when you flash a custom ROM now
WinMO 6.5 is not an installable app/upgrade like upgrading an application on your phone its the operating system itself
Right now and there are very few ROMS out there for WinMO 6.5 and none for the Vogue at all (Im assuming you have a Vogue as this is where you posted) soon there will be one as there are people working on it currently but what is there is EXTREMELY buggy and almost non-functional for the fact its on a phone and a phone should be able to be used after all LOL
Keep with the Custom ROMS for now and wait, the desire for it has been spoken and the Chefs are a cookin LOL
Detroit Doug
NFSFan has confirmed that those WM 6.5 ROMS are FAKE. Even if they were real, there would be no point of using them...
The builds are fake indeed. However they do contain a few components of 6.5. None which are worth upgrading for.
NFSFAN said:
The builds are fake indeed. However they do contain a few components of 6.5. None which are worth upgrading for.
Click to expand...
Click to collapse
Really? What components do they have? Anything from a new today screen or Internet Explorer (like rumored)?
Kinetic scroll (give up TouchFLO and Manila2D), new IE build that supports kinetic scroll. The today screens being posted are fake. They are actually from a smartphone, called HTC Juno. Some asian dude took it out of the Juno, resized the images, and re-arranged the tabs to make it look like the new today screen.
flashing on Vouge
I know this may sound tedious but i have no idea on how to flash any ROM onto my Vouge. Can someone please help. I would love to try out several ROMs and see which one would work best for me.
Thanks in advance
Hey, here is one really good one
Detroit_Doug said:
Basically here are the steps
Download the 2.31 unlocker
Download the ROM you want to use (my personal preference is this one for a TF2D style or this one for a WinMO 6.5 style interface that has TF2D included to switch back and for - both very stable, fast and clean and the thread is very active for help (especially if your on Verizon or Bell which can have issues)
from there, use WinRAR to extract each file into separate folders
then Put your phone in bootloader mode (press and hold power+camera+stylus in reset until 3-color screen comes up)
At this point at the bottom of the screen it will say Serial, plug it into the USB cable or cradle and it should change to USB
Start the exe in the 2.31 and follow the directions (you may get some errors about sleep4.exe just click on OK as it keeps occuring its a XP/Windows7 64 bit issue if that is what your using)
At the point where it tell you to disconect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
once complete, reboot, allow it to do its thing then reboot and go back into bootloader again during reboot you should see coke 2.31 in the upper left if so your ready to go
plug it into your USB/Cradle again and then go into the ROM folder you extracted the ROM into
Once the screen on your phone says USB again go to the folder and double click on the RomUpdateUtility.exe file and follow the directions again, it may take some time so be paitent
once the phone flashes and reboots, let it run and do its thing to the and reboot itself then (and here is an important step for stability) once it starts up do a hard reset (red+green+stylus in reset hole) hit the enter button (center of D-Pad) it will reflash the phone and then red key (send) when prompted
then go thought the setup again, this time you can actually set things up as your keeping them this time and once things are done and your at the start screen on your phone power off (not reset) the phone and then start it up again - seems doing it this way takes care of alot of little issues that will come up before they can happen
Depending on your carrier be sure to have one of the DCD Carrier Cabs as well especially for the 6.5 ROM as it is a generic ROM and some have reported needing to run the DCD Carrier Cab for the service they use to get on the internet and use GPS and the like
Detroit Doug
Click to expand...
Click to collapse
thanks
Everything is working smoothly and better than I thought it would have (i flashed the 6.5 ROM). Thanks to you Detroit Doug or I don't think I would have been able to do it without your instructions. I however do have one more question....i'm having issues syncing the device with my PC now. Any idea on what that could be???
re: Thanks
I've done several resets but to no avail am i able to connect via active sync???
OK maybe i lied about everything working properly and wonderful....so on top of not being able to connect to my PC via activesync I also am not able to connect to the internet on my device, i've downloaded and installed the NFSFAN Sprint GPS Registry but still its a no go... Did i do something wrong completely????? still
I fixed the internet problem!!!!!!!!!!!!!!!!!!!!
....somehow magically i'm now able to connect via activesync. I guess the device just needed time to adjust. Thanks for the help, and i do apologize for the numerous newbie questions.
ehepps said:
....somehow magically i'm now able to connect via activesync. I guess the device just needed time to adjust. Thanks for the help, and i do apologize for the numerous newbie questions.
Click to expand...
Click to collapse
ok so i didnt notice this thread. so whats your secret? howd you get it to work?
mbaseball, I just replied to your thread.
MMS
I flashed the rom perfectly and im lovin every thing bout it but one thing, i cant send or recieve picture mail. Is there a way 2 fix that or sumthin. That takes alot of funny away from the rom. help me please. does there happen to be a 6.5 rom wit picture mail?
Best Windows Mobile 6.5 upgrade for Vogue (Bell)?
hi
I 've been reading this thread, and am just wondering whats' the best download so far for upgrading to Windows Mobile 6.5, for HTC Touch - I think this is the vogue...for Bell Mobility?
If you could please provide a download link.
Thank you all for your help
Thank you
Karim
kchaggani said:
hi
I 've been reading this thread, and am just wondering whats' the best download so far for upgrading to Windows Mobile 6.5, for HTC Touch - I think this is the vogue...for Bell Mobility?
If you could please provide a download link.
Thank you all for your help
Thank you
Karim
Click to expand...
Click to collapse
The best is NFSFAN's Windows Mobile 6.5 ROM. You can find it on another thread in this forum right here:
http://forum.xda-developers.com/showthread.php?t=432487
Don’t even bother with anything else. I am running this. It is fast, stable and very close to the stock WM 6.5 (I have downloaded the device emulator image from Microsoft’s website for software development purposes). The extras that are in there are useful.
The Fish
Hey guys I know this is not the unlocking thread but I tried posting on the thread made by "coke" with no response. So I thought I'd do it here. So here's the story
I have a Sprint Vogue and I was really getting tired of the slow HTC WM 6.1 and all the buttons that I could not modify on the cube (which is useless cuz I dont use any of the them). So I decided to try out a new rom with 6.1 and touchflo 2D.
I went to the ppcgeeks forum to unlock the phone, followed the instructions, read and reread the posts. Finally decided to give it a go. Everything went smoothly until the last step (exitbl) of coke 2.31. It kept telling me to disable USB on activesync and then the program would just shut down! ?? And yes I did disable the USB option for the activesync before that step. I looked under the device information and realized that nothing has changed interms of the ROM. So I tried it again and again (4 times). Then I just reinstalled the HTC 6.1 rom with the 3.42.30 radio... So any ideas on why this may be happening? I promise I followed all the steps
My second question is, in your opinions, what is the most reliable, stable and fast Touch 6.1 rom? Let me know if you have an opinion.
Thanks so much in advance, any help would be appreciated.
I had what sound like the same problem yesterday.
my post is over at ppcgeeks.
"I disconnected but I did not see the phone exit bootloader mode and reset itself.
....
What should I do from here?
Reboot phone, soft reset, hard reset? - go have fun?
....
I did a couple soft resets and have been playing around with it,
I guess I upgraded right... but it was weird there at the end, instructions not the clearest to me, i guess."
mine seems to be working fine, except the weather thing.
shows
in the About section my phone reads
WM 6.1 Pro
CE OS 5.2.21041
Device Information reads
ROM version 1.05.Alltel
Radio version 3.42.30
PRL Version 30008
PRI version 2.02_011
I was kinda scared to do another hard reset b/c I had already changed a bunch of settings.
Sorry if this doesn't help you too much,
but it is nice to know I'm not the only one with this issue
.
Hmm sounds like a similar problem. But I thought it wasn't unlocked unless we saw 2.31.coke somewhere in the device information.
As far as I know, hard reset did not hurt the phone. I tried installing that unlocker 4 times then went with the original HTC rom and it still turned out just like before. It installed the rom fine
Yeah I am still concerned about how it wont go through the exitbl step...
moonwoo said:
Hey guys I know this is not the unlocking thread but I tried posting on the thread made by "coke" with no response. So I thought I'd do it here. So here's the story
I have a Sprint Vogue and I was really getting tired of the slow HTC WM 6.1 and all the buttons that I could not modify on the cube (which is useless cuz I dont use any of the them). So I decided to try out a new rom with 6.1 and touchflo 2D.
I went to the ppcgeeks forum to unlock the phone, followed the instructions, read and reread the posts. Finally decided to give it a go. Everything went smoothly until the last step (exitbl) of coke 2.31. It kept telling me to disable USB on activesync and then the program would just shut down! ?? And yes I did disable the USB option for the activesync before that step. I looked under the device information and realized that nothing has changed interms of the ROM. So I tried it again and again (4 times). Then I just reinstalled the HTC 6.1 rom with the 3.42.30 radio... So any ideas on why this may be happening? I promise I followed all the steps
My second question is, in your opinions, what is the most reliable, stable and fast Touch 6.1 rom? Let me know if you have an opinion.
Thanks so much in advance, any help would be appreciated.
Click to expand...
Click to collapse
Yeah, the directions can be a bit confusing over there on that thread
Basically here are the steps
Download the 2.31 unlocker
Download the ROM you want to use (my personal preference is this one for a TF2D style or this one for a WinMO 6.5 style interface that has TF2D included to switch back and for - both very stable, fast and clean and the thread is very active for help (especially if your on Verizon or Bell which can have issues)
from there, use WinRAR to extract each file into separate folders
then Put your phone in bootloader mode (press and hold power+camera+stylus in reset until 3-color screen comes up)
At this point at the bottom of the screen it will say Serial, plug it into the USB cable or cradle and it should change to USB
Start the exe in the 2.31 and follow the directions (you may get some errors about sleep4.exe just click on OK as it keeps occuring its a XP/Windows7 64 bit issue if that is what your using)
At the point where it tell you to disconect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
once complete, reboot, allow it to do its thing then reboot and go back into bootloader again during reboot you should see coke 2.31 in the upper left if so your ready to go
plug it into your USB/Cradle again and then go into the ROM folder you extracted the ROM into
Once the screen on your phone says USB again go to the folder and double click on the RomUpdateUtility.exe file and follow the directions again, it may take some time so be paitent
once the phone flashes and reboots, let it run and do its thing to the and reboot itself then (and here is an important step for stability) once it starts up do a hard reset (red+green+stylus in reset hole) hit the enter button (center of D-Pad) it will reflash the phone and then red key (send) when prompted
then go thought the setup again, this time you can actually set things up as your keeping them this time and once things are done and your at the start screen on your phone power off (not reset) the phone and then start it up again - seems doing it this way takes care of alot of little issues that will come up before they can happen
Depending on your carrier be sure to have one of the DCD Carrier Cabs as well especially for the 6.5 ROM as it is a generic ROM and some have reported needing to run the DCD Carrier Cab for the service they use to get on the internet and use GPS and the like
Hope that clears up things a bit LOL
Detroit Doug
Doug, when I go into the bootloader it DOES say SPL-2.31.Coke. Does that mean that it is all set? Also this time, it still asked me to disable active sync at this time (at the exitbl step) do you have to run that step to complete the unlock?
This is what my bootloader image says
VOGU100 NFG
SPL-2.31.CoKe
CPLD-3
Let me know if I need to run the exitbl or if I am set to load the rom. Thanks so much for your help!
moonwoo said:
Doug, when I go into the bootloader it DOES say SPL-2.31.Coke. Does that mean that it is all set? Also this time, it still asked me to disable active sync at this time (at the exitbl step) do you have to run that step to complete the unlock?
This is what my bootloader image says
VOGU100 NFG
SPL-2.31.CoKe
CPLD-3
Let me know if I need to run the exitbl or if I am set to load the rom. Thanks so much for your help!
Click to expand...
Click to collapse
Your all set to flash if in bootloader it says as your phone does SPL-2.31.CoKe
you all unlocked and ready to go ... just put your phone in bootloader mode then connect the phone to your PC "serial" will change to "USB" and then run the RomUpdateUtility.exe file and follow along with the bouncing ball, do the watusi, wipe hands on pants - whatever helps you pass the time
but follow the steps as outlined above with the hard-resets and power-offs and the like, believe me its better to solve the issues before they occur than wait and have to start over
Detroit Doug
Doug, it worked like a charm. I did not know that the last step of the unlocker was not required. I installed 6.1 with Touchflo 2D. Looks and feels .. wow. it's the coolest thing I've seen. I've followed all your step including a hard reset before I started using it. So far the speed is impressive.
Couple more questions for you since you are an expert at this.
1. If I reload the factory default ROM, will it reset everything back to normal and can I keep reverting back and forth between different ROMs without any consequences?
2. It (the NFSFAN's 6.1 rom) seems to use less Storage memory (137 free vs HTC's ~100 free) but much more Program memory (59 free vs. ~80 in HTC's) than the HTC default. Any ideas or concerns about this?
All in all thanks so much! Hopefully as I learn more and more I will be able to contribute things too. You are right. This is so cool and highly addictive!!
Take care~ BTW I am in Lansing Go State!
moonwoo said:
Doug, it worked like a charm. I did not know that the last step of the unlocker was not required. I installed 6.1 with Touchflo 2D. Looks and feels .. wow. it's the coolest thing I've seen. I've followed all your step including a hard reset before I started using it. So far the speed is impressive.
Couple more questions for you since you are an expert at this.
1. If I reload the factory default ROM, will it reset everything back to normal and can I keep reverting back and forth between different ROMs without any consequences?
2. It (the NFSFAN's 6.1 rom) seems to use less Storage memory (137 free vs HTC's ~100 free) but much more Program memory (59 free vs. ~80 in HTC's) than the HTC default. Any ideas or concerns about this?
All in all thanks so much! Hopefully as I learn more and more I will be able to contribute things too. You are right. This is so cool and highly addictive!!
Take care~ BTW I am in Lansing Go State!
Click to expand...
Click to collapse
Glad it worked, and Ill try to answer you concerns
1 -Now that it is unlocked go ahead and swap ROMs all you want to, the tricky part is the stock ROM, flashing back to stock can and will revert your radio (if youve upgraded it) and ca cause issues with the unlocker, but a simple run of the unlocker 2.31 again can correct it
2 - NFSFAN like other Chefs have ways of moving data/programs around when they cook up these ROMs utilizing whatever kitchen program they personally prefer that being the case how they data/programs get pushed about can create the speediness you now see in your phone by freeing up the RAM for apps and the like and pushing programs off to the side optimizing how the device should have been setup from the start
As for that, Ive been using his ROMs as well as some others for quite some time and have had little to no issues with how he places the progs and data so I wouldnt worry about it
Yeah, Live in Las Vegas now - but Michigan will ALWAYS be home Go Red Wings !!!!
Detroit Doug
Thanks Doug, for all your information. Your answers were great! Hopefully I wont need too much more help in the future. i'm learning~
Don't mean to go off on a little tangent, but I find this post really helpful and was wondering if you, Doug, or someone else could provide a link to this 2.31 unlocker or whatever it is. Thanks in advance.
hibbiejibbie3 said:
Don't mean to go off on a little tangent, but I find this post really helpful and was wondering if you, Doug, or someone else could provide a link to this 2.31 unlocker or whatever it is. Thanks in advance.
Click to expand...
Click to collapse
http://forum.ppcgeeks.com/showthread.php?t=20370
Detroit Doug
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Reddog80p said:
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Click to expand...
Click to collapse
Check your PM over at PPCGeeks
Detroit Doug
Reddog80p said:
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Click to expand...
Click to collapse
From Detroit_Doug
At the point where it tell you to disconnect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
Maybe wait longer if you can,
I reckon some pc take longer to fully recognize[process] the disconnect and reconnect procedure.
example: disconnect > wait 20-30 seconds > reconnect > wait 20-30 seconds > then continue
I had that same issue and waiting longer during this process helped
.
I can't even get to that point. With active sync on as soon as I start the unlocker RUU it gets the info from my phone and shows the current rom 3.14.605.1 ....I click update and it shows 2.31 unlocker I hit next and then the install status bar comes up on my desktop and my phone goes into bootloader mode and the active sync connection drops and I get the 262 connection error. If I start the RUU with my phone in bootloader usb mode already it does not detect my current rom and I click next. click next to 2.31 unlocker, and it goes through the same steps and I get the same error. Is there anything I have to do to my phone prior to running the RUU. My phone is a verizon xv6900 running wm 6.1 rom 3.14.605.1 with radio 3.37.78
I have the same problem with my new sprint touch. I get error 262 at 0%, did they change something in these new phone that won't allow us to unlock?
Rom is 3.03.651.4
radio 3.42.30
I think I got it, what I did was not to extract the vogue_unlocker_MFG_2.31.exe file but to run it. I had activesync set up and connected, then just ran the unlocker, don't extract it. It will shut off activesnyc and put my phone in to the 3 color screen, form there, just follow the directions. Also I didn't have to run the exitbl step as my phone auttomatically exit and restarted.
I ended up having to re-run the .041 unlocker and then the 2.31 unlocker and it ended up working for me. I'm not sure why I had to because I Had the same bootloader info prior to running the 2.31 unlocker in the first place. The 6.5 rom and gps rom has been working flawlessly for a week now, the only thing I had to do was call up VZW (*8889) the guy answered "account investigations" LOL I told him I had to hard reset and my phone wouldn't authenticate and he asked me to call back from another line. I told him that I had no landline and he said thats fine I can override it just call back right away whenever you get to another phone. That was on friday and I have not called back but I've been able to text, make and receive calls so I don't think I will unless I have to.
gooney said:
I think I got it, what I did was not to extract the vogue_unlocker_MFG_2.31.exe file but to run it. I had activesync set up and connected, then just ran the unlocker, don't extract it. It will shut off activesnyc and put my phone in to the 3 color screen, form there, just follow the directions. Also I didn't have to run the exitbl step as my phone auttomatically exit and restarted.
Click to expand...
Click to collapse
thank you! i did that and it worked for me.
yeah, it says right in the directions over there to just run the exe it will create a temp folder and run the RUU itself from there
Extracting it and running it will always cause issues
also - Ignore the sleep4.exe or whatever if you encounter it - it is a legacy exe that is called that isnt used anymore, wont affect the unlocking just hit OK through it
Detroit Doug