Hi ,
i am facing some troubles with bootloader
just freezing on Loading screen , nothing happend
and i tried FORMAT
is there any solution ?
plz i really need help
i cant unlock or flash roms
Ok have you done the Hardspl? What are you doing step by step? I am sure you can be helped but we need more info. Are you flashing by sd card or active sync?
actually i am tring to HardSpl but i failed till now
every time i try the to Hardspl, i face the error 260 because of my bootloader freeze on the Loading page
and when i get to the boot loader in general not hardspl also after the tricolor screen, facing the Loading page and freez .
so till now my device is locked .
thx
really guys i need help plz
Did you read post 2 of the hard spl thread? There you can find something about error 260. And why do you need to get into the bootloader when you didn't even have hardspl on you're phone?
actually yes i read the second post and tried everything but couldnt have the hardspl
when i want to run the hardspl my device get into the bootloader and freez
Related
Hi guys. I have installed loads of ROMs onto my trusty hermes yet today, when trying to flash DuttyThroys Ultra Ultra Lite rom this happened: i downloaded ROM and installed it, it seemed to install fine, got to 100% and then came up with error message stating that Image File was corrupt. Now my hermes is stuck on the multicoloured bootloader screen?!?!?!? I have SPL 2.10. Hard SPL V7 HERM 100 IPL 1.04 (Dont know which of these is relevant to anythin?) .I have read the WIKI on repairing bricks but for my problem it says to reflash any nbh without radio. How is this possible if i cant get my pc to connect to my hermes???
Tried the method of turning off usb connection in active sync, removing battery, reconnecting to usb and running mitty (command SET 14 0) but nothing happens. Mitty says CMD error and active sync doesnt reopen the connection like the guide says! Man i hate this cuz i have now become one of those annoying noobs who has bricked their phone and hassles everyone for help!!!!
Have also tried to flash from sd card but nothing happens, flicks to white screen with LOADING... on it for 2 secons then flicks back to that wonderful multicoloured screen of joy!
Any help will be appreciated guys, cant live without my hermes!!!
Welcome to the fuc... nightmare world of the brick,i'mma in your same situation,now my Tytn is a piece of white stone,and it seems there's no reason to bring it back to live!
I can't stay without my Tytn i do a lot of things with it,Skype,SIP calls,Mail,Messenger,Memo,Internet......i'm in totally despair!!!
you should be able to just reflash a known good rom.
hfam95 said:
you should be able to just reflash a known good rom.
Click to expand...
Click to collapse
Brilliant story! both compelling and rich. But i have already explained that my pc doesnt recognise my hermes so how do you RECOMMEND i flash??
IT could be interesting to make the minimal effort to go and read the wiki.
anyway:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Better than just cry.
MarcWhittle said:
Brilliant story! both compelling and rich. But i have already explained that my pc doesnt recognise my hermes so how do you RECOMMEND i flash??
Click to expand...
Click to collapse
With the microsd card...
right, its looking good. managed to begin flashing (bar has stopped for ages but having read this is normal im not so scared!) using the SD method. Where my device wasnt superCID i had to use the matching ROM (Orange) to my CID (which incidently i dont know, just downloaded both Orange ROMs).
While im waiting ill try and help you TETSUO! (Im a noob so probably cant!)
Is your device SuperCID??? tell me as much as you can about your device SPL etc
dude, if u read my post u would have seen that i have tried SD method once (sing Black 3.5 not ORANGE ROM), im not crying and im grateful for any help but when i get advice such as 'flash a rom' im gonna be pissed!
And i have read ALL the page on unbricking!!!
It worked!!
One more question, as i have installed a stock Orange ROM do i now need to reinstall HardSPL v7??
Are you on a Win XP or a Vista PC?
XP dude, sorry should have said! and thanks
i went into bootloader, still says 2.10 olipro but when i try to update to new ROM (Black X RC)and pick autodetect it says it says unknown version, use SSPL. it never used to say this so i assume i need to install HardSPL 7 again???
with the tri colour sceen, when you plug the usb cable in does it go from serial to USB ?
what OS have you got ?
just my 2 cents hope it helps.
dude, i have got past that problem and have managed to install an Orange ROM onto it. i only need to know ow whether to install HardSPL v7 again!
sorry slooooooooooooooooow typing
good question hope there an answer,
MarcWhittle said:
dude, i have got past that problem and have managed to install an Orange ROM onto it. i only need to know ow whether to install HardSPL v7 again!
Click to expand...
Click to collapse
just saw your post if ur device is hardspl you just need to supercid your device, If your spl is still showing hardspl and its coming as a error that normally happens to me as well just manually click spl 2.10 and tick (is it hardspl?}
To recap, i have now managed to flash a stock Orange ROM from SD card ( i think the reason it didnt work first time with SD is because device isnt SuperCID and i was trying to flash Black RC, soon as i used Orange ROM (my device is M3100) it worked. I am now back to a fully operational device. I wish to go back to Black but when i AutoDetect what bootloader i have it recommeds SSPL method. Before all my problems it would always automatically pick 2.10?? Does this mean i need to install HardSPL v7 again??
it was HardSPL v7 before all these problems, but im a noob so dont know if it still is?? would installing Orange ROM from SD Card remove HardSPL?? Bootloader still shows SPL as 2.10 oli
MarcWhittle said:
it was HardSPL v7 before all these problems, but im a noob so dont know if it still is?? would installing Orange ROM from SD Card remove HardSPL?? Bootloader still shows SPL as 2.10 oli
Click to expand...
Click to collapse
If you only flash the orange os.nb only then your hardspl wouldnt have changed so its safe to flash your device just manually choose.
If you want to flash hardspl again then do it on a precaution method
Mark,
First of all well done for getting yourself out of a hole. It seems quite difficult to ask for help these days without being shot to pieces even when you have first tried to help yourself by doing all the right things, which is more than can be said for some who come on here asking for help. So well done again.
Re your question, I would reflash Hard SPL anyway to be sure; however before you do that go to the Mr Vanx's guide on hard SPL (forgot the link but type in www.mrvanx.org and you should be taken there) and follow his instructions.
Good luck.
WB
I'm a bit confused here I have managed to flash my o2 orbit from the factory o2 wm6 to wm6 premium plus rom, everything worked fine. Then I tried to flash to black & blue 4.3, I got a 302 error, I went through the recovery process and the same happened again. I managed to get the factory rom from the o2 website and it flashes fine every time but whenever I try to flash with any other rom even the premium plus which worked before, I get the 302 error, do I need to CID Unlock it? I'm stuck, Any help would be much appreciated.
lj-_- said:
I'm a bit confused here I have managed to flash my o2 orbit from the factory o2 wm6 to wm6 premium plus rom, everything worked fine. Then I tried to flash to black & blue 4.3, I got a 302 error, I went through the recovery process and the same happened again. I managed to get the factory rom from the o2 website and it flashes fine every time but whenever I try to flash with any other rom even the premium plus which worked before, I get the 302 error, do I need to CID Unlock it? I'm stuck, Any help would be much appreciated.
Click to expand...
Click to collapse
You must run USPL to flash other ROM than your original. If you flash other roms than supplied with your device, you must CID unlock your bootloader and then will be everything fine.
This is why I am confused, how come the wm6 premium plus rom worked first time and now it dosn't . I use the uspl utility first like I did the first time, the spl then changes to 1.11.0000, then I do the rom update. I didn't do a cid unlock the first time but it worked. My brother has the same o2 xda and has also updated to the wm6 premium plus rom from the factory rom, but never did a cid unlock either.
Yes it is a bit strange, but you have to try use the uspl tool again and again, in some version of uspl i hade succes on 5. try. Or look for other version of USPL, maybe you have the old one.
True, I'll try another uspl. How can I tell if it's a new one? I take it I'm doing the procedure correctly ( Run USPL once, then reset, then install rom) ? or run uspl more than once ?
No, run just once, if succesfull the device will reboot, wait untill the activesync will connect to your device and than run romupdate.When possible after the reboot turn to fly mode and wait till activesync will be syncronised with the device and this time run the update.
Thanks for the help mate, I'll keep on trying that
about uspl
hey wat is uspl and from where u can download this utility for wizard ! i m having the same 302 error while flashing a crossbow rom , active sync dont detect my fone now its been bricked n stuked on bootloader screen ! plz help
z0d1ak said:
hey wat is uspl and from where u can download this utility for wizard ! i m having the same 302 error while flashing a crossbow rom , active sync dont detect my fone now its been bricked n stuked on bootloader screen ! plz help
Click to expand...
Click to collapse
Try to search the forum, you will find the uspl tool. If you see the color screen, you can flash just your original rom version.
hi all ,
my 1st post so hope this is not a silly post .
i have been reading the posts here for 2 weeks and today i got a Vario 2 from ebay , its a great phone i really like it .
i have check the boot loader and it says it has herm300 IPL 1.04 SPL 2.10.01ipro at the botom of the loader screen it says serial , so i guess from that there is no need for me to load Hard SPl as i already have it ?
when i try to load a new rom ( i have tried 5 different ones ) and i use the autodetect method it says unknown version select safe sspl ,should i select the safe sspl or the spl 2.10 ( 4th option down )
sorry to ask its just that as i have only had the phone 3 hours i dont want to trash it just yet
thanks in advance Andy
Dont use the auto-detect one. Just use the option for 2.0 or greated SPL and start flashing. If not you can always use the SD card method. Look in to wiki for more information.
you should really reinstall newest olipro
if you r in boot loader mode auto detect will not work will only work if activesyncd
I would start with the newest at$t rom before flashing a new rom especially a big storage rom
then update radio the DR uses 1.47 I like 1.54.3 myself
then flash away if you have any issues with a rom post in that roms thread instead of starting a new thread.
nate
hi , just wanted to say thanks to both of you for your help and advice , i am in activesync mode so i guess it should detect the SPL ?? i think i will try to re load the hard SPL and then see if it can be detected before i load any roms ? is that the correct thing to do ? will post noob questions in the other forum in future , thanks andy
ive first flashed it whit the olinex 1,34 RUU_Signed.nbh i think its called then i try to flash whit the bsb6 that i want as as my new rom but when it has resetet the device and starting the updating of rom, it freezes at 0%
is there somekind of unlock i still need ? ive read about some hardspl wich i tried but .. it runs thourg the first thing, then the bootloader thing it get to 15% then my device freezes ... what do i do ??
neondyret said:
ive first flashed it whit the olinex 1,34 RUU_Signed.nbh i think its called then i try to flash whit the bsb6 that i want as as my new rom but when it has resetet the device and starting the updating of rom, it freezes at 0%
is there somekind of unlock i still need ? ive read about some hardspl wich i tried but .. it runs thourg the first thing, then the bootloader thing it get to 15% then my device freezes ... what do i do ??
Click to expand...
Click to collapse
Try flashing Olinex 1,39 instead of 1,34. That should solve your problem.
Cheers.
cant find
can you link to the 1.39? cant seem to find it :S
I take it you have read this sticky
http://forum.xda-developers.com/showthread.php?t=416211
Grab hard spl 1.93 from my signature and let me know how it goes...
Hi all , I was just trying to flash my radio from 1.13 to 1.16 .... The progress bar goes to 100% and then theres an error coimng up that FLASH WRITE ERROR and my diamond reboots to bootloader mode and displys the message " Upgrade ROM code error . Please try again... Any help ....
Is it not because you are trying to flash a radio that isn't compatible with your device?
Have you Security unlocked your phone?
Did you follow the tutorial? It said you need to install hardspl first. If not, then there's your problem.
http://forum.xda-developers.com/showthread.php?t=416211
Follow this to the letter.
This can happen if the radio isn't compatible with your device or is security locked. Try a different radio that isn't security locked and you should be good, don't worry you haven't bricked the phone!