Develop Bugs

Trouble with Dopod WM6..

can't seem to get this upgrade to work. the updater stops at about 28 percent for me with an error (286? i think) and after that i'm stuck in bootloader. Every time after that, the updater wont even start.. (a different error).
i can flash successfully a cooked ROM, but can't get the official one to work. Could it be a conflict with Des' crash-proof SPL? That's the only thing i can think of at this point..

To me said invalid device id, and got stuck on the boot loader

try back to any old offical ROM
and then copy SSPL to PDA and run it on PDA
when bootloader appear, run WM6 offical updater
I got same problem too and get fix
good luck

update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?

It installs a new bootloader that can't be hacked by the previous hacks I think.... I'm stuck in it too...
SPL-3.03.0000

racerx_ said:
update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?
Click to expand...
Click to collapse
Hi racerx,
I've encountered the same problem as your, stuck at 28% ERROR [286] while flashing, and couldn't go over it even after recovery process following the instruction.
Could you please explain a bit more details about how to go back to Olipro's hard-spl and enter into bootloader?
Thanks, eager to flash the new ROM...

Well I was able to get out of it by running Pof's CID RUU Unlocker, however, it errors after 7%, and resets. It gets past the bootloader, however, it hardreset the phone...eh.

IT happened to me too - Update Error.
So should i go back to Official WM5 then update to WM6 (i had AX3L installed before and i just had to reflash back to AX3L coz of the error from WM6).
Kinda scared me.....LoL

well, to start with i had Des' Crash-Proof SPL on my phone... so after the updater hung at 28%, i remained in Des' bootloader. I then ran the RUU for pdaviet's ROM, which flashed successfully. After that was on and my trinity was up and running, i flashed Olipro's hard-spl. Then manually put it in bootloader again, and flashed the official ROM.
Let me say this, though. At this point, i think you should be content to get your device out of bootloader mode. This Dopod WM6 doesn't have so much to be desired in it compared to cooked ROM's on this forum, plus your bootloader will be stuck at version 3.xxxx which i don't know if anyone is sure how to deal with yet. I'm regretting flashing mine to official version. Should have waited for a chef to pack it up for me.
what does your bootloader say?

You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.

yeah saw your post on the other thread.. thanks for the tip! talk about a stressful morning haha..
i was waiting for this ROM cause my activesync has mysteriously stopped working for a couple of weeks. so i was going to flash and take it to the service center. The miracle of it, was after my device hung and i reflashed pdaviet's rom, my activesync mysteriously works now even though i reflashed a million times before trying to get it going haha..

new spl is needed for flashing new radio rom with cid locked device.
So that's why RUU reflashes SPL at first.
U could simply reflash HArd spl back by using sspl

mUn, when can we expect your much anticipated "Indigo" rom using this offical WM6 base??

Genius! thanks for the tip mun...
all i can say is one word....
INDIGOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO!!

I also got Invalid vendor ID when I tried to flash for the first time. But it flashed just fine after I put it into bootloader mode. Give it a try..

Flashed my mine in a breeze from LSVW version 27/05/07.

myppcsg said:
Flashed my mine in a breeze from LSVW version 27/05/07.
Click to expand...
Click to collapse
still same problem
can you post the RUU files plz

mxlaser said:
You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.
Click to expand...
Click to collapse
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....

geoffreyhan said:
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....
Click to expand...
Click to collapse
hehe i did that many time this day maybe hmmm 5 or 6 and im still doing that

try to use another version of RUU (the older one)
ps. plz don't post messages about indigo in other tgreads ) if u want to ask - so ask in mine thread.
I'll flash official rom today and then will make some conclusion ) but i thibk that indigo will be based on oficial release

My First Brick..... :eek:

Hi guys. I have installed loads of ROMs onto my trusty hermes yet today, when trying to flash DuttyThroys Ultra Ultra Lite rom this happened: i downloaded ROM and installed it, it seemed to install fine, got to 100% and then came up with error message stating that Image File was corrupt. Now my hermes is stuck on the multicoloured bootloader screen?!?!?!? I have SPL 2.10. Hard SPL V7 HERM 100 IPL 1.04 (Dont know which of these is relevant to anythin?) .I have read the WIKI on repairing bricks but for my problem it says to reflash any nbh without radio. How is this possible if i cant get my pc to connect to my hermes???
Tried the method of turning off usb connection in active sync, removing battery, reconnecting to usb and running mitty (command SET 14 0) but nothing happens. Mitty says CMD error and active sync doesnt reopen the connection like the guide says! Man i hate this cuz i have now become one of those annoying noobs who has bricked their phone and hassles everyone for help!!!!
Have also tried to flash from sd card but nothing happens, flicks to white screen with LOADING... on it for 2 secons then flicks back to that wonderful multicoloured screen of joy!
Any help will be appreciated guys, cant live without my hermes!!!

Welcome to the fuc... nightmare world of the brick,i'mma in your same situation,now my Tytn is a piece of white stone,and it seems there's no reason to bring it back to live!
I can't stay without my Tytn i do a lot of things with it,Skype,SIP calls,Mail,Messenger,Memo,Internet......i'm in totally despair!!!

you should be able to just reflash a known good rom.

hfam95 said:
you should be able to just reflash a known good rom.
Click to expand...
Click to collapse
Brilliant story! both compelling and rich. But i have already explained that my pc doesnt recognise my hermes so how do you RECOMMEND i flash??

IT could be interesting to make the minimal effort to go and read the wiki.
anyway:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Better than just cry.

MarcWhittle said:
Brilliant story! both compelling and rich. But i have already explained that my pc doesnt recognise my hermes so how do you RECOMMEND i flash??
Click to expand...
Click to collapse
With the microsd card...

right, its looking good. managed to begin flashing (bar has stopped for ages but having read this is normal im not so scared!) using the SD method. Where my device wasnt superCID i had to use the matching ROM (Orange) to my CID (which incidently i dont know, just downloaded both Orange ROMs).
While im waiting ill try and help you TETSUO! (Im a noob so probably cant!)
Is your device SuperCID??? tell me as much as you can about your device SPL etc

dude, if u read my post u would have seen that i have tried SD method once (sing Black 3.5 not ORANGE ROM), im not crying and im grateful for any help but when i get advice such as 'flash a rom' im gonna be pissed!

And i have read ALL the page on unbricking!!!

It worked!!
One more question, as i have installed a stock Orange ROM do i now need to reinstall HardSPL v7??

Are you on a Win XP or a Vista PC?

XP dude, sorry should have said! and thanks
i went into bootloader, still says 2.10 olipro but when i try to update to new ROM (Black X RC)and pick autodetect it says it says unknown version, use SSPL. it never used to say this so i assume i need to install HardSPL 7 again???

with the tri colour sceen, when you plug the usb cable in does it go from serial to USB ?
what OS have you got ?
just my 2 cents hope it helps.

dude, i have got past that problem and have managed to install an Orange ROM onto it. i only need to know ow whether to install HardSPL v7 again!

sorry slooooooooooooooooow typing
good question hope there an answer,

MarcWhittle said:
dude, i have got past that problem and have managed to install an Orange ROM onto it. i only need to know ow whether to install HardSPL v7 again!
Click to expand...
Click to collapse
just saw your post if ur device is hardspl you just need to supercid your device, If your spl is still showing hardspl and its coming as a error that normally happens to me as well just manually click spl 2.10 and tick (is it hardspl?}

To recap, i have now managed to flash a stock Orange ROM from SD card ( i think the reason it didnt work first time with SD is because device isnt SuperCID and i was trying to flash Black RC, soon as i used Orange ROM (my device is M3100) it worked. I am now back to a fully operational device. I wish to go back to Black but when i AutoDetect what bootloader i have it recommeds SSPL method. Before all my problems it would always automatically pick 2.10?? Does this mean i need to install HardSPL v7 again??

it was HardSPL v7 before all these problems, but im a noob so dont know if it still is?? would installing Orange ROM from SD Card remove HardSPL?? Bootloader still shows SPL as 2.10 oli

MarcWhittle said:
it was HardSPL v7 before all these problems, but im a noob so dont know if it still is?? would installing Orange ROM from SD Card remove HardSPL?? Bootloader still shows SPL as 2.10 oli
Click to expand...
Click to collapse
If you only flash the orange os.nb only then your hardspl wouldnt have changed so its safe to flash your device just manually choose.
If you want to flash hardspl again then do it on a precaution method

Mark,
First of all well done for getting yourself out of a hole. It seems quite difficult to ask for help these days without being shot to pieces even when you have first tried to help yourself by doing all the right things, which is more than can be said for some who come on here asking for help. So well done again.
Re your question, I would reflash Hard SPL anyway to be sure; however before you do that go to the Mr Vanx's guide on hard SPL (forgot the link but type in www.mrvanx.org and you should be taken there) and follow his instructions.
Good luck.
WB

Custom ROM, Unlocker?

Okay so I read this..
"a. unlock your phone ( ImCoKeMaN's Vogue unlocker found here : http://forum.ppcgeeks.com/showthread.php?t=20370)
b. upgrade your radio (most recomend the Bell ROM for that, if your not with Bell do not let the customizations run)
c. Load a custom ROM (Most Vogue users rightfuly recomend NFSFans ROMS for good reasons)"
I see that I need to unlock my phone, I'm with Telus and can somebody tell me in that thread what unlocker I'm so post to download. Also once I've unlocked my phone, how do I upgrade radio and how do I load custom rom? Also when the rom is loaded when I turn my phone on from then on it will look like the custom rom?

I'm in the exact same boat. Can someone please tell us the steps (in order) on how to
1. unlock the telus HTC touch (I think it's that .coke program).
2. Upgrade the radio -- where do you find the info on how to do that?
3. Do you have to do that stuff to activate GPS BEFORE or AFTER upgrading the ROM?
Thanks in advance

Im with Telus also using NFSFans Custom Rom
Download the new rom update at
http://www.htc.com/us/
Run the Rom updater on PC with your phone on active sync
its gonna take like 10-15 mins to finish (let it reboot and customize your mobile)
once its finished you should now have Window's mobile 6.1 with radio 2.31
Then run the vogue unlocker
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker_MFG_2.31.exe by ImCokeMan
Your phone should be unlocked now!
(That's all i did on mine anyways)
(Bricked my phone too trying to make my own rom lolol
You can also use that unlocker to unbricked your phone)
GL!

[Q] NOOB HERE Please HELP!!

Im new to flashing on win mobile based phones and i just needed to know a few things
1.Do i hard reset after the upgrade has completed auto customization or in the middle of boot up process?
2.I used the sim and cid unlocker v3 and it automatically flashed SPL 1.40 OLIPro, can i upgrade to HARDsplv7 without losing Super CID and unlocked sim attributes?
3.Im using a windows vista comp and i realize every time i revert to cingular stock rom i cannot upgrade i get errors, does it work if i run the wrapper in compatibility mode?
Im Using a Cingular 8525 Thanks for the help

here's what i knew;
1- i think you should do the hard reset thing when you see the screen calibration applet, i used to do it by that.... but for 2 and 3.....nothing much i could help.....got few ideas in mind but wont say it....i dont really want to trash your valuable hermes....i suppose you should wait for a better man to help you....regards

DroidFreek said:
Im new to flashing on win mobile based phones and i just needed to know a few things
1.Do i hard reset after the upgrade has completed auto customization or in the middle of boot up process?
2.I used the sim and cid unlocker v3 and it automatically flashed SPL 1.40 OLIPro, can i upgrade to HARDsplv7 without losing Super CID and unlocked sim attributes?
3.Im using a windows vista comp and i realize every time i revert to cingular stock rom i cannot upgrade i get errors, does it work if i run the wrapper in compatibility mode?
Im Using a Cingular 8525 Thanks for the help
Click to expand...
Click to collapse
Answers:
1.- This is my way to flash and is prettie fast
-Flash stripped att stock rom, it boots, and fast put it into Bootloader when you see red words
-Flash your new custom rom, and fast do hardreset when you see the red words
2.- Yes you can... sorry... you MUST!!! to change to V7 just flash it as any other rom
3.- The main suggestion is to run the wrapper in XP i never tried before compatibilitie with XP execution on Vista, but you can try or... put a JAVA emulator machine in your vista... and run a virtual XP machine and do upgrades in the virtual JAVA machine

[Q] Flashing Original Stock Rom

Hi Guys I need your help.
I have a tilt 2 that I hard SPLed and installed Energy Titanium.
I wanted to put the original Stock att rom back in it since most of the roms I've put into it is still under development and missing a lot of stuff.
So i dled "Stock_SPL_Restore_087.zip".
I Task29 it first.
Then I got customRUU.exe with the RUU_Signed.nbh (from the Stock_SPL_Restore_087.zip) and put it into a folder. Then ran customRUU.exe from the bootloader.
Now on the bootloader screen I see SPL-0.87.0000
When I let it boot It just goes to a white screen with " ATT and World Phone" on it, and after a few seconds it reboots by itself again.
So my questions are:
Can I reflash HardSPL from the bootloader?
Can I still load a stock or any other rom to it?
Is this what it means to be bricked?
How to fix this issue?
I did read the FAQs
And yes I do get the 260 error.
Thank you for all your help!

Wow noone knows? : (
Can anyone help?

You should have flashed the stock ROM BEFORE the SPL. You could try extracting the NBH from the stock ROM and flashing that from the bootloader. I'm not guaranteeing anything, though. You should have followed the directions.