[Q] Flashing Original Stock Rom - Touch Pro2, Tilt 2 Windows Mobile General

Hi Guys I need your help.
I have a tilt 2 that I hard SPLed and installed Energy Titanium.
I wanted to put the original Stock att rom back in it since most of the roms I've put into it is still under development and missing a lot of stuff.
So i dled "Stock_SPL_Restore_087.zip".
I Task29 it first.
Then I got customRUU.exe with the RUU_Signed.nbh (from the Stock_SPL_Restore_087.zip) and put it into a folder. Then ran customRUU.exe from the bootloader.
Now on the bootloader screen I see SPL-0.87.0000
When I let it boot It just goes to a white screen with " ATT and World Phone" on it, and after a few seconds it reboots by itself again.
So my questions are:
Can I reflash HardSPL from the bootloader?
Can I still load a stock or any other rom to it?
Is this what it means to be bricked?
How to fix this issue?
I did read the FAQs
And yes I do get the 260 error.
Thank you for all your help!

Wow noone knows? : (
Can anyone help?

You should have flashed the stock ROM BEFORE the SPL. You could try extracting the NBH from the stock ROM and flashing that from the bootloader. I'm not guaranteeing anything, though. You should have followed the directions.

Related

Trouble with Dopod WM6..

can't seem to get this upgrade to work. the updater stops at about 28 percent for me with an error (286? i think) and after that i'm stuck in bootloader. Every time after that, the updater wont even start.. (a different error).
i can flash successfully a cooked ROM, but can't get the official one to work. Could it be a conflict with Des' crash-proof SPL? That's the only thing i can think of at this point..
To me said invalid device id, and got stuck on the boot loader
try back to any old offical ROM
and then copy SSPL to PDA and run it on PDA
when bootloader appear, run WM6 offical updater
I got same problem too and get fix
good luck
update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?
It installs a new bootloader that can't be hacked by the previous hacks I think.... I'm stuck in it too...
SPL-3.03.0000
racerx_ said:
update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?
Click to expand...
Click to collapse
Hi racerx,
I've encountered the same problem as your, stuck at 28% ERROR [286] while flashing, and couldn't go over it even after recovery process following the instruction.
Could you please explain a bit more details about how to go back to Olipro's hard-spl and enter into bootloader?
Thanks, eager to flash the new ROM...
Well I was able to get out of it by running Pof's CID RUU Unlocker, however, it errors after 7%, and resets. It gets past the bootloader, however, it hardreset the phone...eh.
IT happened to me too - Update Error.
So should i go back to Official WM5 then update to WM6 (i had AX3L installed before and i just had to reflash back to AX3L coz of the error from WM6).
Kinda scared me.....LoL
well, to start with i had Des' Crash-Proof SPL on my phone... so after the updater hung at 28%, i remained in Des' bootloader. I then ran the RUU for pdaviet's ROM, which flashed successfully. After that was on and my trinity was up and running, i flashed Olipro's hard-spl. Then manually put it in bootloader again, and flashed the official ROM.
Let me say this, though. At this point, i think you should be content to get your device out of bootloader mode. This Dopod WM6 doesn't have so much to be desired in it compared to cooked ROM's on this forum, plus your bootloader will be stuck at version 3.xxxx which i don't know if anyone is sure how to deal with yet. I'm regretting flashing mine to official version. Should have waited for a chef to pack it up for me.
what does your bootloader say?
You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.
yeah saw your post on the other thread.. thanks for the tip! talk about a stressful morning haha..
i was waiting for this ROM cause my activesync has mysteriously stopped working for a couple of weeks. so i was going to flash and take it to the service center. The miracle of it, was after my device hung and i reflashed pdaviet's rom, my activesync mysteriously works now even though i reflashed a million times before trying to get it going haha..
new spl is needed for flashing new radio rom with cid locked device.
So that's why RUU reflashes SPL at first.
U could simply reflash HArd spl back by using sspl
mUn, when can we expect your much anticipated "Indigo" rom using this offical WM6 base??
Genius! thanks for the tip mun...
all i can say is one word....
INDIGOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO!!
I also got Invalid vendor ID when I tried to flash for the first time. But it flashed just fine after I put it into bootloader mode. Give it a try..
Flashed my mine in a breeze from LSVW version 27/05/07.
myppcsg said:
Flashed my mine in a breeze from LSVW version 27/05/07.
Click to expand...
Click to collapse
still same problem
can you post the RUU files plz
mxlaser said:
You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.
Click to expand...
Click to collapse
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....
geoffreyhan said:
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....
Click to expand...
Click to collapse
hehe i did that many time this day maybe hmmm 5 or 6 and im still doing that
try to use another version of RUU (the older one)
ps. plz don't post messages about indigo in other tgreads ) if u want to ask - so ask in mine thread.
I'll flash official rom today and then will make some conclusion ) but i thibk that indigo will be based on oficial release

Vogue Stuck at HTC Screen

Hey Guys,
I was trying to flash ToO's Cricket Rom to an HTC Sprint Vogue and after the process was finished it is stuck on the "HTC Smart Mobility" screen. I used an unlocker by cokeman before flashing I I think I need to re-lock the handset to flash it back to the original sprint ROM. However I need the older sprint rom and not the new one with GPS. When I put the phone in bootloader mode this is what it says:
It says:
VOGU100
SPL-0.41 Coke
CPLD-3
Where can I get the older ROM for the sprint vogue?
Update:
I am not able to load the original Sprint ROM. It errors out everytime at about 29%
Planetneo said:
Hey Guys,
I was trying to flash ToO's Cricket Rom to an HTC Sprint Vogue and after the process was finished it is stuck on the "HTC Smart Mobility" screen. I used an unlocker by cokeman before flashing I I think I need to re-lock the handset to flash it back to the original sprint ROM. However I need the older sprint rom and not the new one with GPS. When I put the phone in bootloader mode this is what it says:
It says:
VOGU100
SPL-0.41 Coke
CPLD-3
Where can I get the older ROM for the sprint vogue?
Update:
I am not able to load the original Sprint ROM. It errors out everytime at about 29%
Click to expand...
Click to collapse
Check PPCGeeks, there is a thread with factory ROM's.
Try doing this check your registry under HKEY_LOCAL_MACHINE\Software\Arcosoft\ArcSoft MMS UA\Config\mm1\MMSCsettings\make sure you only have one entry: Cricket MMS if you have another named Default or Sample, delete them and then try again; if it fails Delete all, soft re-boot and then install your ROM. Good luck.
Planetneo said:
Hey Guys,
I was trying to flash ToO's Cricket Rom to an HTC Sprint Vogue and after the process was finished it is stuck on the "HTC Smart Mobility" screen. I used an unlocker by cokeman before flashing I I think I need to re-lock the handset to flash it back to the original sprint ROM. However I need the older sprint rom and not the new one with GPS. When I put the phone in bootloader mode this is what it says:
It says:
VOGU100
SPL-0.41 Coke
CPLD-3
Where can I get the older ROM for the sprint vogue?
Update:
I am not able to load the original Sprint ROM. It errors out everytime at about 29%
Click to expand...
Click to collapse
I'm a little confused on the issue. If you want to flash roms with GPS you need to be unlocked with Imcokes 2.31 not 0.41 unlocker. Once unlocked you can flash to the stock roms. I flash back to Sprints stock GPS rom all the time. Be careful of flashing from a GPS rom back to a non GPS rom. This could cause some issues.
If you are trying to relock your phone thats a different issue.
EDIT: After rereading. Did you try flashing from a non gps rom to a gps rom or vice versa? Your phone looks to be unlocked with a non-gps unlocker. Is the cricket rom GPS?
When flashing a custom ROM your Vogue needs to be unlock with 2.31 (GPS) or .40 (non GPS). Not too sure about cricket but would assume if you have a radio version of 3.xx.xx would be GPS. Hopefully you have not bricked your Vogue.
You may find more help at ppcgeeks.com or ppchaven.com.
You may have to resort flashing your ROM in the bootloader mode,
SAME PROBLEM with Vogue
I think I have the same problem as the one who started this thread. here is what I did:
I unlocked a Vogue with the non-gps unlocker (SPL-0.41.Coke)
then I loaded a GPS rom onto the phone (OMJ 3.09)
and now it is stuck at the HTC Screen.
I then tried to flash a stock ROM to the phone, but as descreibed above it will not fully load- it stops at 29 percent- tried it a couple times.
I then tried the OMJ 3.09 again and it still stuck in HTC Screen, and says "No radio.'
I am trying to figure out what to do. I was told by someone to load a GPS radio into it and see if it boots. I have the radio to install but not sure if thats best bet.
I was told by someone else to install nongps radio and then install a nongps rom.
One concern I have is that I will brick my phone that way (if i try to downgrade to a nongps radio after installing a gps rom...but im not sure that the gps rom actually installed a gps radio or not cuz my phone was only .41 unlocked)
Also, I cant seem to install a stock rom because it stops at 29 percent.
Any ideas?
Thanks
found answer
to anyone else with this problem- I just installed this rom: http://forum.xda-developers.com/showthread.php?t=357762
and all was well including radio.
Just thought that I would post what happened to my phone and the steps that eventually recovered it in case it helps somebody else:
My phone was stuck with "No Radio" on the boot loader screen and the SPL as "SPL-2.31.CoKe", but none of the 3.x ROMs would flash properly that I tried. So here are the steps that eventually recovered it (mostly...):
1.) I installed the ROM above from the tri-color screen (power+camera+reset). I still had no radio, but it was letting me past this and booting up to WM.
2.) I then re-flashed the 2.31.CoKe boot loader (not sure if this step is necessary but listing what worked...)
3.) I tried to install RUU_Vogue_VZW_WWE_3.14.605.1_Radio_3.37.78_Ship.exe but it failed at 10% restarting to RUUNBH screen and the installer gave me Error [290]: Invalid Command
4.) I then tried to install the latest sprint ROM straight from the HTC site:_Touch by HTC (Sprint)_RUU_PPST_Vogue_SPRINT_WWE_3.03.651.4_2_Radio_3.42.30_AM_NV_2.04_Ship this looked like it was going to fail at the same part the Verizon rom did as it rebooted at 10% to RUUNBH screen, but the Sprint installer did something (I heard the computer lose and gain connection multiple times) and eventually it went right back and continued on from 11% and finished successfully.
5.) Rebooted and I had a radio now! Rather then risking trying to install the Verizon ROM again I went straight to the custom ROM I had originally started out with: NFSFAN 6.5 V6 which is working fine for me, except the GPS which is what started out my adventure of the last 3 days...
Just a note: for all flashes except the final one I simply waited till it was at the "Tap the screen..." stage till flashing. I never let any ROM but the final one run it's customization.

Urgent! My diamond has hardware problem and need to fallback to stock ROM and SPL.

Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810
Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help
Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.
If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included
Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.
You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Here you go....I did a search
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4
band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...
kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.
f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that
f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??
R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??

Is it possible to upgrade rom from bootloader mode?

Well, I tried to build rom from my backup of the original rom shipped with my device.
Now I've got to check it somehow to see if its good.
I havent hard-spl my device yet, but im going to do it now.
I couldnt find direct answer, but what happens if I try to flash bad image?
Im going to use the hardspl 1.93 olinex unsigned.
If the Image I created isn't working properly, I'll be able to flash my device with another rom for bootloader mode?
If so, how?
(of course, Im assuming bootloader mode will be accessable even though I flashed bad image?)
thanks
yes..i have flash my device a few time from the bootloader screen..its appear "usb" and than your pc see the device..start RUU and flash it againt
butevery time you flash..is possible to brick the device..becarefull
put in the storage card the file .nbh and rename it in "DIAMIMG.nbh" than press volume down and backspace+tasto reset..hold the buttons and flash without pc...this is the faster way (less 1minutes)
ps i never brick any phone..and flash a few time a week with new release and mine
hi there Soikiro,
sorry for being a bit noob at this, but would greatly appreciate if you could explain if it is changing the spl that will brick the phone, or flashing the rom that may brick the phone?
And if the phone is brick, can I reflash it back to default?
Thanks for your help!
Three may be more possibility for bricking the device during changing of spl. So be careful and choose correct one for your device. You may play with the rom. But be careful of spl.{sorry for my bad english}

[TUT] HOW-TO restore Diamond to stock for warranty

Due to a hardware problem in my Diamond I needed to restore it to manufacturer default. I didn't find a guide to this and since I've done the research anyway I thought I'd put together this little tutorial as the information was somewhat scattered around the forum. I hope this guide will be of use for the community.
My phone was originally branded and sim-locked by 3. After I was through with it, it was SIM-unlocked, security unlocked and had HSPL, custom ROM and a radio ported from another device. The steps below is what I did to restore it to stock. All steps might not be neccessary for you. This procedure might also work for other devices than the Diamond, but of course you need other versions of SPL, ROM etc.
1. Backup everything on your phone to your computer - use activesync, PIMbackup etc and make a copy of your Internal Storage.
2. Make a hard reset (hold vol down + enter and soft reset) and chose to format moviNAND. This step is only neccessary if you want to wipe your Internal Storage before you send the device in for repair, but I recommend it.
3. Go to www.htc.com and download the latest stock ROM (includes stock radio and SPL). You find it under Support and you enter your s/n to get the correct stock ROM for your device, complete with branding for your operator. You can also find stock ROMS here: http://forum.xda-developers.com/showthread.php?t=471699
4. Flash the stock ROM. Now you have stock ROM and Radio on your device. Stock SPL will not be installed until you've replaced HSPL with an older stock SPL and flashed ROM again.
5. Get RUU-SSPL and stock SPL from HERE:
http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39. I used the stock 1.93 SPL. Some instructions and info about restoring stock SPL is in the linked post by cmonex and due credit goes to her. I will repeat some of that info to keep this guide step-by-step. EDIT: Stock SPL 2.03 can be found here: http://forum.xda-developers.com/showpost.php?p=3359191&postcount=390
6. Put the .nbh file from the SPL you downloaded into the same folder as the extracted contents of RUU-SSPL-withoutNBH.zip and run the RUU. This flashes an old stock SPL.
7. Flash your stock ROM from step 3 again. This step is neccessary to get the correct stock SPL on your device, eg. the one that corresponds with the stock ROM you've downloaded in step 3. It was not installed in step 4, because then you still had HSPL. In step 6 you've installed a stock SPL and now the correct stock SPL will flash along with the stock ROM. After this step I got SPL 2.03 on my Diamond.
8. Remove the Security Unlock from your device using the instructions and Security Relocker by Olinex from this post by cmonex: http://forum.xda-developers.com/showpost.php?p=3299516&postcount=492
Now, my Diamond is still SIM-unlocked. I have not managed to find any info about how to restore the SIM-lock, but it is hopefully not neccessary for warranty. As far as I can tell, the unlock doesn't show anywhere, but of course all they need to do is to try a SIM-card from another operator...
If anyone has info about how to restore SIM-lock, then I'll update this guide with that info.
good job...
moderator make this "sticky"
3dward87 said:
good job...
moderator make this "sticky"
Click to expand...
Click to collapse
I second that, it contains links to stock ROMs, that'll hopefully stop a million topics about it lol.
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Da9L said:
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Click to expand...
Click to collapse
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
where can i read more information about jumpspl, how it works and everything?
eranyanay said:
where can i read more information about jumpspl, how it works and everything?
Click to expand...
Click to collapse
Look in the Xda-wiki, search and google, and not just in the Diamond section.
sticky please
this needs to be a sticky topic.
losdrivare said:
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
Click to expand...
Click to collapse
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Da9L said:
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Click to expand...
Click to collapse
Sorry to hear it and I'm afraid I'm out of ideas. After all, my little tutorial is primarily aimed at those whose Diamonds have working screens...
On another note, my Diamond came back from warranty repair and the repair shop had not noticed anything that would void my warranty. In the meantime I got myself a Topaz and now I've sold my Diamond, but I'll be checking this thread from time to time.
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
donsalari said:
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
Click to expand...
Click to collapse
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
losdrivare said:
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
Click to expand...
Click to collapse
Very true!!! Ok cool... Flashing back to stock!!
Thanks..
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Da9L said:
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Click to expand...
Click to collapse
Another idea: maybe you can find some a VNC program that also works the "other way" with windows mobile, so that you can get a window on your PC with the screen of your device?
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
herpez said:
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Click to expand...
Click to collapse
k3nnyboiboi said:
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
Click to expand...
Click to collapse
If you manage to install ANY stock SPL and then flash the correct ROM for your country and operator then you automatically get the correct SPL too, since stock ROMs include SPL. If you go to htc.com and type in your s/n then you automatically get the latest ROM for your device and operator.
k3nnyboiboi said:
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
Click to expand...
Click to collapse
I only link to the SPLs provided by olipro and cmonex in the hard-SPL thread. If you need closer info about SPLs I suggest you ask there. I only tried to revert back to stock SPL 1.93 myself and it worked just like described in first post.
Thanks Op
Managed to restore it no problem, but took ages

Categories

Resources