Related
Ok I've flashed close to a dozen times using various great ROMS everyone has provided and never had a problem. Today I realized that ATT/HTC released their official ROM yesterday and I thought I would give it a try. I followed their instructions but it did not work.
My phone looked as though it was updating and it got stuck at 11%. Followed the instructions to recover and it still did not work. Now my phone is stuck at the Triple Color Bar screen and I cannot do anything.
Did I brick my phone?
Can I use some of the options to try to unbrick in the xda wiki?
Thank you in advance.
- Monty
Have you tried flashing a different rom or using a different pc to flash with?
i managed to revive mine from that state the key is getting the usb to let you update again dont plug in the cable until after the ruu is looking for the connection might take a couple tries but that worked for me.
Hi
Try this:
1) Turn your phone off completely
2) Hold the side OK button and the power button, at the same time push the reset button at the bottom with your stylus.
3) this should get you into the bootloader (the three colour screen)(dont be lazy and just let it load into the bootloader, actually run the key sequence ive just mentioned!)
4) on your PC run the update, i would reccomend the latest official update for your handset, BUT, do the following:
a) Make sure you have WinRAR installed
b) Right click on the update file you have just downloaded
c) 'Extract' the update file to the folder it makes
d) within that folder should be ANOTHER executable file that has the same icon as the original update
e) Extract this file again
f) open the folder it makes and within that there should be a RUUSIGNED.NBH and also the RUU utility itself
5) Run the update utility in the second folder
6) once the utility has loaded, plug your phone in (the text will change from 'SERIAL' to 'USB')
7) proceed with the update and see what happens
hope that helps
good luck.
MontyV77 said:
Ok I've flashed close to a dozen times using various great ROMS everyone has provided and never had a problem. Today I realized that ATT/HTC released their official ROM yesterday and I thought I would give it a try. I followed their instructions but it did not work.
My phone looked as though it was updating and it got stuck at 11%. Followed the instructions to recover and it still did not work. Now my phone is stuck at the Triple Color Bar screen and I cannot do anything.
Did I brick my phone?
Can I use some of the options to try to unbrick in the xda wiki?
Thank you in advance.
- Monty
Click to expand...
Click to collapse
You should not update using the Oficial ROM release Update because you put in the boot loader from here (Hard-SPL-V7) and it will try over righting the entire rom if you do and is probably what messed up your update attempt. Use Dutty's NBH tool and just decompile the NBH of the official rom, then recompile the windows, splash screens and radio into a new NBH then flash using the RUUwrapper from this site to flash the phone.
TooSharp said:
Have you tried flashing a different rom or using a different pc to flash with?
Click to expand...
Click to collapse
Yes I've tried two different Official ATT ROMs and on different computers but same problem. Actually the only one that will attempt to start loading are the ATT ROMs and none of the cooked ROMs here are loading. Maybe that has something to do with the way they are packaged.
Jefem24 said:
i managed to revive mine from that state the key is getting the usb to let you update again dont plug in the cable until after the ruu is looking for the connection might take a couple tries but that worked for me.
Click to expand...
Click to collapse
Yeah I've done this now over a dozen times since yesterday and still no luck.
duke_stix said:
Hi
Try this:
1) Turn your phone off completely
2) Hold the side OK button and the power button, at the same time push the reset button at the bottom with your stylus.
3) this should get you into the bootloader (the three colour screen)(dont be lazy and just let it load into the bootloader, actually run the key sequence ive just mentioned!)
4) on your PC run the update, i would reccomend the latest official update for your handset, BUT, do the following:
a) Make sure you have WinRAR installed
b) Right click on the update file you have just downloaded
c) 'Extract' the update file to the folder it makes
d) within that folder should be ANOTHER executable file that has the same icon as the original update
e) Extract this file again
f) open the folder it makes and within that there should be a RUUSIGNED.NBH and also the RUU utility itself
5) Run the update utility in the second folder
6) once the utility has loaded, plug your phone in (the text will change from 'SERIAL' to 'USB')
7) proceed with the update and see what happens
hope that helps
good luck.
Click to expand...
Click to collapse
This looked the most promising maybe because it felt like I was doing something and I was using the ATT ROM again to update, and it actually started updating again. But it stopped at 11% again and gave me the 262 error.
Below pulled from readme.txt file.
"ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode."
Click to expand...
Click to collapse
Tried to soft-reset and reinstall but same problem.
Scrambler001 said:
You should not update using the Oficial ROM release Update because you put in the boot loader from here (Hard-SPL-V7) and it will try over righting the entire rom if you do and is probably what messed up your update attempt. Use Dutty's NBH tool and just decompile the NBH of the official rom, then recompile the windows, splash screens and radio into a new NBH then flash using the RUUwrapper from this site to flash the phone.
Click to expand...
Click to collapse
Haven't yet tried this because I am having a hard time getting details on this. I've been searching looking for "duttythroy nbh tool", "nbh tool", "dutty nbh tool", and "dutty's nbh tool" and I can't find it.
If this helps anyone this is what I have on my tri-color screen:
HERM100
IPL - 1.04
HERM100
SPL - 2.03
Click to expand...
Click to collapse
You can also try to flash from the SD card:
- format a SD card with FAT32
- extract the .NBH file from the rom image you like (for your device of course)
- rename the .NBH to HERMIMG.NBH and copy it to your SD card
- put SD card in phone and start it in bootloader (hold OK button on left side and POWER button at same time and stick with stylus in RESET on bottom)
- confirm flashing on screen
- flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes.
This also works for normal (non preproduction) devices but keep in mind that if the CID does not match the flashing might not work. - this was taken from one old thread
- notes - you should backup everything on your SD card to your PC (because except for HERMIMG.NBH it should be blank)
- you can not get USB related error because it loads from a card
- if you flash official ROM you flash it with everything - radio ROM, Windows and bootloader
I am not really sure about bootloader you should have but for official upgrade official bootloader should be ok (it is first thing to be flashed - so I think you have bootloader from ATT ROM already.
Hope it can help somehow...
hey, what is your spl version?
it should say on your bootloader mode
and then read this http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
that really helps a lot, it has the solution and stuff. hope you unbrick your phone! all i did was download the update and it reloaded to wm5 update on my 8525 then after that, i went for olipro's 2.10 so i dont unbrick it anymore =) then flash all you want!
oh yea the factory update for my 8525 that unbricked my phone was this http://www.htcamerica.net/support/8525/software-downloads.html
try loading that in your phone =)
Ok that was the oddest thing but it worked. I've been trying to possibly unzip some of the packages by way of what duke_stix instructed. My last ROM was Schaps most recent 4.0. I unzipped what he had and ran the RUU file. What was funny though is that it started updating up to 3% then gave me the 260 error but this time my phone restarted and booted back up. I don't know what happen but it works now. If this is suppose to go in as a fix I don't know what happen.
Thank you everyone for all your help. I want to reflash my ROM but I will wait until I see this working for a while.
- Monty
asianr0cker said:
...i went for olipro's 2.10 so i dont unbrick it anymore =) then flash all you want!
Click to expand...
Click to collapse
How do I change my SPL to 2.10 now?
Here is nice tutorial how to flash HardSPL v7 (a.k.a. bootloader 2.10 Olipro). Glad to see you are out of brickland
KarhU said:
Here is nice tutorial how to flash HardSPL v7 (a.k.a. bootloader 2.10 Olipro). Glad to see you are out of brickland
Click to expand...
Click to collapse
Thank you just finished flashing it. Thanks again to all that helped.
MontyV77 said:
How do I change my SPL to 2.10 now?
Click to expand...
Click to collapse
See mrvanx.org
... Edit: That's what you get for waiting 10 minutes before posting. Doh!
Thank You So Much !
I did all pricedures and it worked perfectly. You are the best dude!
duke_stix said:
Hi
Try this:
1) Turn your phone off completely
2) Hold the side OK button and the power button, at the same time push the reset button at the bottom with your stylus.
3) this should get you into the bootloader (the three colour screen)(dont be lazy and just let it load into the bootloader, actually run the key sequence ive just mentioned!)
4) on your PC run the update, i would reccomend the latest official update for your handset, BUT, do the following:
a) Make sure you have WinRAR installed
b) Right click on the update file you have just downloaded
c) 'Extract' the update file to the folder it makes
d) within that folder should be ANOTHER executable file that has the same icon as the original update
e) Extract this file again
f) open the folder it makes and within that there should be a RUUSIGNED.NBH and also the RUU utility itself
5) Run the update utility in the second folder
6) once the utility has loaded, plug your phone in (the text will change from 'SERIAL' to 'USB')
7) proceed with the update and see what happens
hope that helps
good luck.
Click to expand...
Click to collapse
if its an official rom you may need to hard sol it first as i had the same problem updating to original after a chefs special
blowfeld said:
if its an official rom you may need to hard sol it first as i had the same problem updating to original after a chefs special
Click to expand...
Click to collapse
what is a hard sol and how do I do it? I wanna go back to the OEM Official ROM to see if it fixes my no service phone problems.
Ok, I've tried everything that was posted in this thread and nothing worked so far.
My last setup before trying to reinstall the Radio is:
AT&T 8525 (location - Hawaii)
Black Majik's WM6
Herm Radio 1.43.00.00
Hard SPL-V7
The OS has been working great until this previous Monday. Also just in case if this is any relevant, Hawaii has just recently upgraded and turned on it's 3G network just a couple of weeks ago. They are still tweaking the whole thing to make sure all is well. Unfortunately it seems that something they did this past Monday seemed to really screw up the 8525's.
The reason I'm trying to reinstall my radio is because I happened to go to the phone settings, and saw that there was no Radio version on the screen. Thought this might also add to the problem.
Well where I'm at now is that I'm stuck at the Tri-Color loader screen. I've read the Wiki regarding fixing a bricked phone. Doesn't seem to help.
So I'm now stuck and need expertise of more knowledgeable members who might have been in the same situation as me.
Please, really need help as this is a company phone and I've got to get it working cause I don't wanna have to pay for it.
Hey, currently i have kavana rom installed from a long time ago and it seem like when i turned it on this morning the whole rom is messed up.. my two left and right soft key doesn't work and i can't even go to settings or anything.. I try to flash it back to its original tmobile rom but it doesn't work... anyone have any suggestion? i haven't used this phone for a long time and i need to lend it to my uncle so i need a answer asap. thanks!
btw... it keep saying the image file is corrupted!
stuck on HTC screen!!!
i tried doing the hard reset but after i press the send button it just stays at the htc screen. I was flashing the original tmobile rom and i accidently dropped it and lost connection, after that it gets stuck on the htc screen and wont start up... what can i do? is this fixable?
i believe if you go to the bootloader screen you can flash back to the original t mobile rom. ummm use the wiki tab to find the rom and how to get to that screen. hope this helps
Yes it is fixable. All you have to do is hold the camera (sym) button down for about 10 seconds, then plug the usb cable in while still holding it down. You now should see a tri-colored screen. When you see this screen you can flash you phone with the OFFICIAL ROM (the rom the phone came with).
This rom could be found below (in my signature).
Hope this helps.
Also, once you have the original rom on there you can always reflash to the new 6.1 rom or whatever rom you would like.
Try to download the Tmobile Rom from below (in the official rom section) I have this posted in my signature.
jdoggraz said:
Yes it is fixable. All you have to do is hold the camera (sym) button down for about 10 seconds, then plug the usb cable in while still holding it down. You now should see a tri-colored screen. When you see this screen you can flash you phone with the OFFICIAL ROM (the rom the phone came with).
This rom could be found below (in my signature).
Hope this helps.
Also, once you have the original rom on there you can always reflash to the new 6.1 rom or whatever rom you would like.
Click to expand...
Click to collapse
i did exactly as you have told me but it is still stuck on the HTC screen. I turned on the phone, held down the sym button/camera for 10 seconds i tried holding it longer and then plug the usb cable back in but it is still stuck on the HTC screen. thanks
Ok take out the battery, then insert the battery in. Hold the button down and make sure the usb is plugged in the computer and then plug it in to the phone.
jdoggraz said:
Ok take out the battery, then insert the battery in. Hold the button down and make sure the usb is plugged in the computer and then plug it in to the phone.
Click to expand...
Click to collapse
alright thanks got it to the boot loading screen/tri color. ok as you have read my previous post... now i can't flash it to any rom. it keep saying the image file is corrupted.. i downloaded everything again and it still says the same thing. When my dash was able to start up i ran the CID bypass and then run the rom installer and it worked but like i said, i accidently dropped it and lost connection. now i can't even run the CID bypass cause i can't even start up the phone... what should i do?
Well you will need to flash it with the original rom the phone came with, i.e. if its a tmobile phone, then you must reflash with the tmobile rom... Once you have the tmobile rom up and running then you can reflash with any other rom i.e. the 6.1 rom.
and you can find the original roms under offical roms below.
jdoggraz said:
Well you will need to flash it with the original rom the phone came with, i.e. if its a tmobile phone, then you must reflash with the tmobile rom... Once you have the tmobile rom up and running then you can reflash with any other rom i.e. the 6.1 rom.
Click to expand...
Click to collapse
alright.. i kinda got it working and its flashing right now.. thanks for ALL your help.. i appreciated!
porkch0p said:
alright.. i kinda got it working and its flashing right now.. thanks for ALL your help.. i appreciated!
Click to expand...
Click to collapse
Oh no problem, once you have the rom all working then you can download the new 6.1 from below. I recommend using it because its awesome. Also once you install this rom make sure you run connection setup under the tools folder to get the network working.
Would I need the unlock code again?
How do I use that T-Mobile download? It only has a single file? Any guidance welcome.
T-Mobile Dash
1.22.531.6 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?z4vjgzxisrz
1.22.531.4 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?yygkw1d5xmc
http://member.htc.com/RuuDownload/T-...eDownload.aspx Valid T-Mobile IMEI Required
1.11.531.1 (T-Mobile USA, WM5)
http://rapidshare.com/files/10464194...531.1.exe.html
T-Mobile MDA Mail
Files Needed to Upgrade or Downgrade (With only the .nbh file)
----------------------------------------------------------------------------------------
Click to expand...
Click to collapse
Where it says "Files Needed to Upgrade or Downgrade (With only the .nbh file)" Click on that and there should be a text file giving you instructions on how to continue.
I get the fundamentals of Simunlock v/s AppUnlock etc.
It was SimUnlocked using Unlock code I had got from T-Mobile.
1. It already has the latest Official ROM version on it (i.e. I tried doing it with the latest T-Mobile) and it shows the version I have is the same.
Do I need to reflash it with the ROM that is aleady present on my DASH? Is it worth trying that?
2. Now the step called AppUnlock? Which tool should I use given that I would have the T-Mobile Carrier 6.1 ROM on it (either already or reflash with T-Mobile 6.1 AGAIN)
3. After AppUnlock should I go for the FLASHing guide? Which one would that be?
MOD EDIT: Can you help, I flashed my GSM diamond with the CDMA hard SPL from PPCGeeks: http://forum.ppcgeeks.com/showthread.php?t=36062
i try to unlock my htc diamond using solution
Code:
FIRST AND MOST INPORTANT!!!
U guys MUST have HardSPL INSTALLED on ur phones BEFORE trying anything of this out...
I Suggest u use HArdSPL 1.40 Unsigned (Its in the RAR file)
AFTER u have installed HardSPL 1.40 Unsigned
Unrar and go to step 2 folder and run -> DiamonCustomRUU.exe
Just do what it says and update.
After the phone restart copy DiamUnlock.exe from the step3 folder on to your diamond
(Anywhere) and run it.
The DiamUnlock.exe closes itself very fast, i have sucessfully made it by first launching the
program and quickly and several times press up button and touch the screen
if you'r lucky the screen stay and you can sim-unlock your diamond!!
the problem that phone came in step 2 after 100% write , it show error 262
any solution thx
Please post in the thread where you got it from!
You'll get an answer, and there will be fewer threads lying around here!
i don't understand what do u mean by this ?
now i use solution from
http://forum.ppcgeeks.com/showthread.php?t=36062
after write rom my htc is totaly dead can't power on
any solution to recover it
hbstun said:
i try to unlock my htc diamond using solution
Code:
FIRST AND MOST INPORTANT!!!
U guys MUST have HardSPL INSTALLED on ur phones BEFORE trying anything of this out...
I Suggest u use HArdSPL 1.40 Unsigned (Its in the RAR file)
AFTER u have installed HardSPL 1.40 Unsigned
Unrar and go to step 2 folder and run -> DiamonCustomRUU.exe
Just do what it says and update.
After the phone restart copy DiamUnlock.exe from the step3 folder on to your diamond
(Anywhere) and run it.
The DiamUnlock.exe closes itself very fast, i have sucessfully made it by first launching the
program and quickly and several times press up button and touch the screen
if you'r lucky the screen stay and you can sim-unlock your diamond!!
the problem that phone came in step 2 after 100% write , it show error 262
any solution thx
Click to expand...
Click to collapse
He means you should ask in the thread where you found this information above.
Code:
First and foremost...
ah ! ok
i don't remember when i found it
but now my htc is totaly dead , how i can recover it ?
hbstun said:
ah ! ok
i don't remember when i found it
but now my htc is totaly dead , how i can recover it ?
Click to expand...
Click to collapse
I am not sure you can.
Does it go into bootloader mode? If not, might be JTAG is your only option.
When you say 'totally dead' do you mean you get absolutely nothing when you try plugging in the usb cable ?
Logically as soon as you plug in the cable it'll power on into the tri-colour screen.
It'll do this even if you remove the battery.
aE3-ink said:
When you say 'totally dead' do you mean you get absolutely nothing when you try plugging in the usb cable ?
Logically as soon as you plug in the cable it'll power on into the tri-colour screen.
It'll do this even if you remove the battery.
Click to expand...
Click to collapse
nothing hen i put usb cable nothing in the screen
Kevbodian said:
I am not sure you can.
Does it go into bootloader mode? If not, might be JTAG is your only option.
Click to expand...
Click to collapse
what do u mean by jtag and how i can do it ?
<mod mode>
Please stop spamming the forum with requests for Help and I have updated the title of this post so that it may get more attention.
</mod mode>
JTagging can be done using QMAT, if need be.
Before that, can you put your Diamond into the Bootloader or not ??
Thanks
Dave
Serves you right for using a leaked unlocker program - Should have gone here . thanks to Olipro as the leaked version was buggy.
I do hope you get this fixed though. (I would help if I could really).
DaveShaw said:
<mod mode>
Please stop spamming the forum with requests for Help and I have updated the title of this post so that it may get more attention.
</mod mode>
JTagging can be done using QMAT, if need be.
Before that, can you put your Diamond into the Bootloader or not ??
Thanks
Dave
Click to expand...
Click to collapse
can't enter bootloader ?
hbstun said:
can't enter bootloader ?
Click to expand...
Click to collapse
In that case I suggest you PM ViperBJK and as him nicely to look at the thread...
He's the main man on JTAG'ing.
Thanks
Dave
DaveShaw said:
In that case I suggest you PM ViperBJK and as him nicely to look at the thread...
He's the main man on JTAG'ing.
Thanks
Dave
Click to expand...
Click to collapse
ok thx anyway for your help
R3PUBL1K said:
Serves you right for using a leaked unlocker program - no sympathy or help from me.
Should have gone here thanks to Olipro as the leaked version was buggy
Click to expand...
Click to collapse
I think he tried the unlock before he flashed the cdma hardspl.
Kevbodian said:
I think he tried the unlock before he flashed the cdma hardspl.
Click to expand...
Click to collapse
yes i tried unlock but failed
i found rom in some website and i flashed it to my phone
but now it dead
You must eter in "USB Trigger Mode"
hbstun said:
yes i tried unlock but failed
i found rom in some website and i flashed it to my phone
but now it dead
Click to expand...
Click to collapse
I think I can help you ...
Just this **** happened to me too ... because I did not read carefully ROM-destination, but we resolved the issue after a couple, three hours of bloody despair ...
Be sure before you get to work, you already have prepared a full ROM image (....nbh) for your Diamond, that is to contain radio too. If you do not have a full version, download a full version first and make sure that contains both ROM and Radio.
1. Take cover behind the phone
2. USB link cable to the computer and phone
3. Open the phone
4. Enter bootloader mode as follows:
Keep the volume down key and click with the stylus reset button (red button which is located behind the device ) for 3-4 seconds in the same time with the volume down key, then you can get out your stylus, and continued to keep volume down key, until the bootloades screen appears, now you can release the volume key down too.
And now, just simply launch DiamonCustomRUU.exe to start your flash, using a file manager, and is ready ... you have a new phone!
I hope I was helpful ...
kokocf said:
I think I can help you ...
Just this **** happened to me too ... because I did not read carefully ROM-destination, but we resolved the issue after a couple, three hours of bloody despair ...
Be sure before you get to work, you already have prepared a full ROM image (....nbh) for your Diamond, that is to contain radio too. If you do not have a full version, download a full version first and make sure that contains both ROM and Radio.
1. Take cover behind the phone
2. USB link cable to the computer and phone
3. Open the phone
4. Enter bootloader mode as follows:
Keep the volume down key and click with the stylus reset button (red button which is located behind the device ) for 3-4 seconds in the same time with the volume down key, then you can get out your stylus, and continued to keep volume down key, until the bootloades screen appears, now you can release the volume key down too.
And now, just simply launch DiamonCustomRUU.exe to start your flash, using a file manager, and is ready ... you have a new phone!
I hope I was helpful ...
Click to expand...
Click to collapse
can't enter bootloader like u sad !
hbstun said:
can't enter bootloader like u sad !
Click to expand...
Click to collapse
Hello there! Where have you blocked, exactly ...?
Hi everybody,
I just bought myself a new vogue from Bell today and I unlocked it w/ imcoke 2.31. I followed all the directions and bootloaded was completed.
Then I installed NFSfan's 1.29 Bell rom. I downloaded the newest bell version and clicked on romUpdateUtility.exe and followed the direction after reading readme first. This is my first time flashing a rom..
Now here comes the trouble.. When I am done with the flashing and my phone restarted itself, it got stuck on the blue screen with bell logo on ><
Please help. I tried hard resetting and it didn't bring back the factory rom.
Also, when I pressed power+camera+reset, it does say imcoke's name..
Because it got stuck, I cannot even do active-sync w/ my computer. What can I do? Also when I did a soft-reset,which brings up the htc screen
it says: R:1.59.10a ; D:3nfs
Can anyone tell me how to fix this please? Thank you all in advance.
Did you upgrade the radio to 3.42.50 with the Official Bell 6.1 ROM first?
If not, download it with the link supplied, put your phone into bootloader mode and flash that first.
http://www.htc.com/ca/supportdownloadlist.aspx?p_id=70&act=sd&cat=all
When complete, put into bootloader mode again then flash 1.29
Don't worry, if you can get into bootloader mode, your phone is not bricked, it's just waiting for a ROM image.
jmitr said:
Did you upgrade the radio to 3.42.50 with the Official Bell 6.1 ROM first?
If not, download it with the link supplied, put your phone into bootloader mode and flash that first.
http://www.htc.com/ca/supportdownloadlist.aspx?p_id=70&act=sd&cat=all
When complete, put into bootloader mode again then flash 1.29
Don't worry, if you can get into bootloader mode, your phone is not bricked, it's just waiting for a ROM image.
Click to expand...
Click to collapse
Thanks for the quick Help.As you can tell, I am panicking..
I am downloading the file now. How can I go into bootloader mode? Is it the tri-colour screen?
And how can I get that file on my computer w/o active sync working? My computer said it cannot detect my phone.
Thanks again.
It is amazing! The bootloader is loading w/ htc updating rom even when a/s is not working!!
Thanks a bunch. I will report my progress after installing every step.
my phone did have communication error while flashing, but luckily there was a visual tutorial to walk me through. Thank you for your help
-----------------------------------------------------------------------------------------------------------------
Currently flashing 1.2 now.*cross my fingers*hope it works. I really want to go to bed w/ the peace of mind.
Yay! it is working now. THank you so much sir.
I can go to bed now
huhu321 said:
Yay! it is working now. THank you so much sir.
I can go to bed now
Click to expand...
Click to collapse
That's great, I just got up and checked to see how your doing.
Custom ROMS are great, enjoy!!
After doing soft reset to my htc trinity it gave me black screen and nothing than this...tried flashing new rom i entered boot loader and flashed correctly but after it finished flashing and reset it gave me black screen also tried different roms but same proplem
Can Anyone help?!!
Hai...! I am not expert on this stuff . may the other can give you a good solution to solve your problem. Did you try to hard reset your device or do hard SPL before flashing? if you didn't do the Hard SPL that's the problems. Some one said to fix the broken Trinity with JTAG Solution, be careful to do this.
See for the thread about JTAG to unbrick your Trinity on this forum.
Hope it will help you...
hmmm..i use olipro 1.30 hard spl,,,but i am wondering why just it cant be replaced by old spl?? and also using the JTAG solution seems dangerous alittle
EgyPharaoh said:
hmmm..i use olipro 1.30 hard spl,,,but i am wondering why just it cant be replaced by old spl?? and also using the JTAG solution seems dangerous alittle
Click to expand...
Click to collapse
Hi EgyPharaoh, Have you tried flashing back to the Stock OEM ROM yet? That will usually fix problems with a bad flash for me. You can find it HERE. I would not recommend looking into JTAG just yet.
If this does not work, let me know and we will research the next step.
SuperSport said:
Hi EgyPharaoh, Have you tried flashing back to the Stock OEM ROM yet? That will usually fix problems with a bad flash for me. You can find it HERE. I would not recommend looking into JTAG just yet.
If this does not work, let me know and we will research the next step.
Click to expand...
Click to collapse
I started flashig it but it reaches about 28% then gives me upate error [262]..but i flashed official htc rom "HTC [WWE] v1.23.405.2] with no errors and when i open it it shows the "htc image" and freezes.
and it says in the readme that if this error showed then it might be that the wince is destroyed or in upgrade mode...how to know now wether it is destroyed or in the upgrade mode??
EgyPharaoh said:
I started flashig it but it reaches about 28% then gives me upate error [262]..but i flashed official htc rom "HTC [WWE] v1.23.405.2] with no errors and when i open it it shows the "htc image" and freezes.
and it says in the readme that if this error showed then it might be that the wince is destroyed or in upgrade mode...how to know now wether it is destroyed or in the upgrade mode??
Click to expand...
Click to collapse
Sorry about the delay, and thank you for the PM reminder.
Try flashing directly from the BootLoader Screen, by holding both the Power and Camera Buttons while you press and release the Reset Button using your stylus. Continue to hold the Power and Camera Buttons until your phone enters bootloader.
If that does not work, try to flash using your SD Card.
Using either 7zip or WinRAR, extract the contents of the OEM ROM you downloaded earlier. You are looking for the RUU_signed.nbh file inside. If you prefer to just download it, you can find it HERE.
Rename the file from RUU_signed.nbh to TRINIMG.nbh and copy it to your SD Card. Don't place it in any folder, just in the Root of the Card. Place the SD Card back into your phone if it's not already.
Now, Enter Bootloader by holding both the Power and Camera Buttons while you press and release the Reset Button using your stylus. Continue to hold the Power and Camera Buttons until your phone enters bootloader. It should at this time start to flash the OEM ROM you copied earlier. Hopefully, this will be successful. If it is, it will have replaced your HardSPL ROM & Radio, so you will need to flash those again.
Let me know if this works or not.
SuperSport said:
Sorry about the delay, and thank you for the PM reminder.
Try flashing directly from the BootLoader Screen, by holding both the Power and Camera Buttons while you press and release the Reset Button using your stylus. Continue to hold the Power and Camera Buttons until your phone enters bootloader.
If that does not work, try to flash using your SD Card.
Using either 7zip or WinRAR, extract the contents of the OEM ROM you downloaded earlier. You are looking for the RUU_signed.nbh file inside. If you prefer to just download it, you can find it HERE.
Rename the file from RUU_signed.nbh to TRINIMG.nbh and copy it to your SD Card. Don't place it in any folder, just in the Root of the Card. Place the SD Card back into your phone if it's not already.
Now, Enter Bootloader by holding both the Power and Camera Buttons while you press and release the Reset Button using your stylus. Continue to hold the Power and Camera Buttons until your phone enters bootloader. It should at this time start to flash the OEM ROM you copied earlier. Hopefully, this will be successful. If it is, it will have replaced your HardSPL ROM & Radio, so you will need to flash those again.
Let me know if this works or not.
Click to expand...
Click to collapse
Thanks For your solution but it didn't work
i did all what u said and that's what happened :-
TRINIMG.nbh
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM -
GSM -
Update In Progress...
and that's all it stops at the first..i read in another thread about flashing from sd card and it said that it may stop for a while but it stops forever
Next Step
TRINITY BACK!!! xD
YEAAAAH I DID IT
well supersport, thanks alot for your help...it helped me alot
the nbh file of the dopodasia rom u gave me didnot work so i tried the same thing but with the old rom i have, the "Htc official rom v1.23.405.2" i took the file named "TRINIMG_HTC_WWE_1.23.405.2_Ship.nbh" and renamed it to "TRINIMG.nbh" then put it in my sd card ..and flashed it and update succeeded and my trinity now works good..thank you and anyone helped in this thread
EgyPharaoh said:
YEAAAAH I DID IT
well supersport, thanks alot for your help...it helped me alot
the nbh file of the dopodasia rom u gave me didnot work so i tried the same thing but with the old rom i have, the "Htc official rom v1.23.405.2" i took the file named "TRINIMG_HTC_WWE_1.23.405.2_Ship.nbh" and renamed it to "TRINIMG.nbh" then put it in my sd card ..and flashed it and update succeeded and my trinity now works good..thank you and anyone helped in this thread
Click to expand...
Click to collapse
Awesome, glad to hear it worked. Remember, you will need to Flash HardSPL again if you want to flash Custom ROMs again, and also an updated Radio if you prefer.
SuperSport said:
Awesome, glad to hear it worked. Remember, you will need to Flash HardSPL again if you want to flash Custom ROMs again, and also an updated Radio if you prefer.
Click to expand...
Click to collapse
but i found that my radio & hardspl didnt change.
EgyPharaoh said:
but i found that my radio & hardspl didnt change.
Click to expand...
Click to collapse
Then you are fine. I guess you have an OEM ROM that has the HSPL and Radio stripped out of it.