Related
Hi guys.
I was using the installed the FInixNOver 3.0.1 ROM onto my SPV M700 and it was great. I've had it for about 2 weeks without any problems.
Last night I looked at my phone, only to realise that it was completley dead. This didnt shock me to much because the battery was running low, and i decided to let it die completley before recharging it again.
I charged my phone overnight and switched it on this morning, but the phone would freeze at the 'FInixNOver' splash screen (the numbers at the bottom of the screen would appear overlaying the splash, but the phone wouldnt go pass this point).
The only way to turn off the phone from this state is to eject the battery. I have tried removing the sim card, turning it back on in as many ways as possible but to no avail. I am able to get to the TriColor test screen (im running IPL-0.50 / SPL-1.30.Olipro) but with all the custom roms available, they all use the ROMUpdateUtility which requires the phone to have established an activesync connection initially (but this would mean my phone would have to be 'on completley' - so this is catch 22.)
For the record, my phone/battery died while my wired handsfree was attached (dunno if thats of any interest to anyone or the rom baker).
But it looks like the only way i'll be able to flash my phone is by finding a way to install the .nbh file without using the RUU method. Because I can put my phone into test mode manually.... any help or guidence would be very much appriciated.
Thanks.
Ok can you get it into bootloader? power/camera buttons and reset?
sorry didnt read fully.
right get your device into bootloader first,
then open active sync (are you using xp)
then open connection settings and disable usb connection,
put your device into bootloader mode, then run any rom upgrade, i prefer the WM6.1 pdaviets from HERE (Username: PDAVIET / Password: pdaviet)
Your pda does not need active sync with ruu's, so no catch 22. if you turn off usb connection in active sync, you can still run ruu and it will be recognised, unless you are using vista, where you need to change your HTC SYNC drivers.
Thanks for your quick response...
Yes I can get into boot loader using the power and camera buttons (or holding the power and camera buttons when resetting the phone)...
When the phone is in boot loader mode, active sync doesnt even detect the phone anyway, but nevertheless, I have followed your instructions and disabled the USB Connection. (BTW, yes i am using XP)
The phone is still in boot loader mode, so now i try and execute the ROMUpdateUtility.exe and go through the steps, at the 1st step i tick the tickbox and click next, and the 2nd step i tick the tickbox and click next. (this step says DO NOT enter the bootloader manually? - but i have havent i?) anyway, when i click next, it says... "Verifying the information on your Trinity... Please Wait..." for about 10 seconds, and then i get a message "ERROR [260] : CONNECTION"
What am i doing wrong?
Huumm.. why dont you flash your phone throw the sd card??
Read this link:
http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
try to flash your phone with some official rom and after that flash it with any other you want!
manos_23 said:
try to flash your phone with some official rom and after that flash it with any other you want!
Click to expand...
Click to collapse
I would recommend this option above, to be safe, i usually get them error messages when the battery is below 50% or sometimes i try it again and it works. it does state do not manually enter bootloader but i always do it this way.
also make sure active sync is not still running in taskmanager under the alais: wcescomm.exe and WCESMGR.exe, end them both.
I've just tried using an official ROM, but the problem still occurs with the 'connecting'. It doesnt seem that the computer picks up a connection to the phone whatsoever.
Should i be concerned that at the bottom of the bootloader screen it says "serial", is this correct?
Im starting to get annoyed now.
Bye,
the bottom of the sreen mast say "usb" not serial.
it seems there is a problem, if it states serial. as it should say usb. try THIS
Seems like the problem was that my USB lead was loose and made a bad connection, hence why the bootloader showed 'serial' and not 'usb'... as soon as i wiggled it and heard the 'connection noise' in windows, i knew i was good to go, and so using the RUU worked fine to reupdate my phones ROM.
Thanks for your help.
My only question is that why did it happen in the first plave?
WIZZKID - I just saw your post here now. I have to tell you that I also saw "SERIAL" at the bottom of the bootloader screen and not "USB". As I said I returned it to get another phone but maybe I will try something else for now instead of a P3600i. I will monitor your thread to see how it turns out for your phone, because it seems that we have the same problem.
if you see "serial" instead "usb" your problem is in the usb cable, usb port from your computer or in the usb connector from your trinity!!!!!
I was having the same problem that you have!! my problem was from my usb from mine trinity!! see if the conector is at good conditions !!!
Well as some of you may know, I got my Trinity replaced for sticking at the WM splash screen after a few days. This second one - I have had it ONE night - and the same thing has happened with incomplete booting. This time I have been trying all night to flash the phone to an official ROM, but I cannot do it (apparently) because I can't establish a connection via ActiveSync. When I stick the data cable in while in bootloader I see SERIAL replaced by USB and when I try the flash I get a "270" error (cannot connect to phone) and the phone re-boots to the sticking plash screen. What should I do now?
ladies and gentlemen...
we've got a lot of mixed messages in this thread.. please make sure you're posting the right thing. no need to disable USB when manually going in to bootloader to flash (at least in xp).. Also, you can ignore the part of the RUU that says 'do not manually enter bootloader' (you should really read the guide on my site)
foxuniform- can you please give some details..
1) are you running xp or vista
2) have you flashed hard-spl? if so what version?
in the mean time, try a couple of things.. first, flash hard-spl (even if you already have it, but from the sound of it i think you don't have it on your device).. if that works, try to flash an official ROM. Can also try to use splxploit, then flash hard-spl, and then flash official ROM (there's a guide on my site if you're unsure)
please post your results
*edit*
here are the steps for SD card upgrade, but i HIGHLY recommend flashing Hard-spl first..
try to do it from SD card. how?
Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract (http://www.cabextract.org.uk/) .
Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
When flashing completes soft-reset your device.
Make sure your SD has FAT32 and has no label. There have been reports that if SD has a label the bootloader can not access the TRINIMG.nbh
racerx_ I have carefully read your response and suggestions, and thanks for your expertise input on the matter. I am fairly new to this stuff so read below carefully as you may find errors in the way I tried to go about doing what I was hoping to accomplish.
First let me answer your questions. I am running Windows XP. The phone is in it's completely natural state in that I have not flashed it in any way. The ROM I was TRYING to flash to the phone while it was not starting properly (this is where I manually entered bootloader) is an official ROM from the HTC website (please note everyone that when I registered my P3600i on the HTC website it came up as the Dopod 810). Anyway, that never worked. ActiveSync never detected the phone (and I guess that's the reason I could not do anything as far as flashing goes). I HARD-RESET my P3600i and it booted normally. I re-installed all the stuff I had on it, from memory card to various .cab files, and the phone is working beautifully thus far. I will report if anything funny happens again.
I have to ask you racerx_, if I CAN flash hard-SPL on the P3600i according to the lovely guide on www.trinityguides.info. I have been of the opinion that things don't work for the P3600i as they did for the P3600, and that has been echoed by many P3600i users on this forum who are ready and waiting to try out some cooked ROMs (myself included).
For the sake of record, my phone is running rom version 3.00.707.17 and radio version 1.46.00.11. I patiently await your response.
woaaahhh..
i didn't notice the 'i' in your previous post... yeah, as far as i know, these ROMs are not flashable on your p3600i.. sorry..
**correct me if i'm wrong somebody**
Yeah I kinda thought that would be your response. By the way - do you think that this phenomenon of sticking at the Windows Mobile splash screen (both the P3600 and P3600i models apparently) has anything to do with something users do with the devices, or you figure it's an inherent software glitch of some sort? I am wondering if I should try a different model or hold on to my P3600i? Hope it's not something that'll happen again - I fly for a living and it's not gonna be good to have the thing screw up on me away from base - I really count on it for everything from casual keeping in touch on Messenger to viewing my work schedule. I love the Trinity though - it's one of my all-time favourite HTC phones.
hmm... i don't think its inherent in the Trinity.. (not a hardware issue.. in my opinion)
its been a while since i followed the posts on it, but always seems to be software related.. sometimes ROM-specific problem. Personally, i've probably flashed as many ROMs as anyone and the only time i ever encountered problems was with the official HTC WM6 ha.. go figure.. I think ppl did find that hard resets before and after flashing are helpful as well..
i love my trinity, and there's not much else on the market to make me want to trade it in (is it just me, or have pda's kind of stopped getting cooler).. i'd stick with it..
As newbie on this, anyone please guide me step by step to upgrade my P3300 rom with nbh file. My device is unlock already with current ROM 5.2.1908 (build 18125.0.4.2).
The procedure is given in almost every thread. It's simple really. Is your SPL version anything other than 1.11.0000 or 1.11.cmon? If yes then your phone is not unlocked. Unlock your phone by running USPL from here or the updated USPL from here.
Check if the USPL has worked by checking your SPL number. During phone booting at the white HTC screen your SPL should show either 1.11.0000 ir 1.11.cmon.
If it does you are free to flash any ROM. Get the ROM of your choice, put your phone into bootloader mode by pressing the voice record, power key and reset button simultaenously for about 5 seconds till you see a three colored screen. Attach it with USB and flash the rom using RUU.
thanks randythered for ur reply. I did w/o problem on USPL but how to use the nbh extention? where that nbh file I shall put in? pc or devise or on specific folder? I got the three colors already, then what next? pl. enlighted
stacknickel said:
thanks randythered for ur reply. I did w/o problem on USPL but how to use the nbh extention? where that nbh file I shall put in? pc or devise or on specific folder? I got the three colors already, then what next? pl. enlighted
Click to expand...
Click to collapse
do u have only .nbh file or along with .nbh file any other files are there ?
generally along with the .nbh file there are other files like romupdateutuility.exe etc.,
download those files also and save those files into your PC.
after unlocking your device then staup the device with bootloader mode (three color screen)
connect the Device with the PC by USB cable.
in the device display u will a word USB (left bottom corner)
run the Romupdateutility from the PC...
the process will guide u next steps ...
after the completion u will have new OS
Last I would recommend tht u also upgrade you Radio ROM (this is responsible for all the communication functions of ur phone i.e. calls, GPS, WiFi etc) which will enhance the communication capabilities.
Radio ROMs Link : http://wiki.xda-developers.com/index..._RadioUpgrades.
Note : before flashing any ROM or upgrading the RADIO kindly CID unlock your device or you will end up the with bricked device .
You can download my ROMs, they come with the full package
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
stacknickel said:
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
Click to expand...
Click to collapse
your device not properly CID unlocked...
unlock the device properly with USPL...
stacknickel said:
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
Click to expand...
Click to collapse
As sixthsigma said, did you check if the phone is correctly unlocked? Is the SPL showing 1.11.0000 or 1.11.cmon?
Secondly, what OS are you flashing on? XP, Vista or Windows 7?
Hi Randythered, IPL 1.25.0001 and SPL 1.27.0000
I am using your ROM RtR Manila v1.0
using XP
Well, firstly thank you for wanting to try out my ROM
Secondly, you haven't unlocked your phone properly yet. The SPL must be 1.11.0000 or1.11.cmon, depending on which USPL you use.
strange... hv tried several time but w/o luck...
now I notice that it cut out after '70' and jump into 100 with disconnecting
any choices of other USPL instead of the one attached here?
Did you flash the old USPL or the new one which is nosize? It is preferable to install the old one first. And then go for the cmon nosize USPL if need be.
From a noob to a noob
Hi, heres the procedure for upgrading your rom put as noob friendly as i can put it.
WHAT YOU NEED
1. HTC Artemis p3300
2. computer running Windows XP with activesync installed
3. Usb cable to connect to computer
4. The new rom that you want to flash
5. And USPL which can be downloaded at this page http://forum.xda-developers.com/showthread.php?t=311403
NB: For most of the newer roms you will probably need the updated nosize version of uspl http://forum.xda-developers.com/showthread.php?t=521406
PREPARATION
NB: Anything you need to backup or keep from your device do it now.
NB: in some cases you may have to hard reset your device before it will take the flash
1. Extract Uspl to your desktop
2. Extract the rom you downloaded to your desktop
3. Remove your sim chip and memory card from your device
4. Reset your device and sync with windows xp
UPDATING
1. In the USPL folder run the program called "start_uspl" and let it do its thing in the dos window,in
my case it goes to 70 and then jumps to 100,if you have been watching your device screen you will
see the linux penguin for a few seconds and it will change to a white screen.
A window will popup on your computer, do as it requests, when finished it will reset your device.
Sync your device with your computer again.
2. In your downloaded rom folder you should find a file called "ROMUpdateUtility.exe" or "Ruu.exe", run
it and a window will popup, do as it requests.
Your device screen will go tri-color(red,green,blue) and the rom update will begin, wait till it
finishes and thats it.
thanks soloman1 and others
finally I got it with removing the sim card and memory card prior to upgrading
stacknickel said:
thanks soloman1 and others
finally I got it with removing the sim card and memory card prior to upgrading
Click to expand...
Click to collapse
same ting got me with my first rom thats why i thought to put it in, happy flashing (not in the naked way )
Lol I can't belive I forgot to tell you that!
It's ok. Thanks to u too randythered.
Do you have dedicate Manila in cab file?
Thank you, here you go!
sixthsigma said:
your device not properly CID unlocked...
unlock the device properly with USPL...
Click to expand...
Click to collapse
Sixthsigma...you said - "unlock the device properly with USPL..." - how do I do that?
I got the same error as mentioned when trying to flash using the numb3rs ROM:
http://thewingster.com/numb3rs.aspx
I ran the herald-uspl.exe file. and ended up with teh above error. My TMo Wing has the original ROM on it and the phone itself is probably unlocked. Ive had it for a year now. Do I need to call TMo to unlock or is there some app I can run to do this myself?
appreciate any help!
nevermind, it worked ok on the second attempt!
Hi all!!
Ever since I got my Sprint Vogue, I have spent God only knows how many hours looking for and gathering information regarding this phone (flashing instructions, unlocking, SuperCID, etc). There are a few sites that have fairly comprehensive guides as to how to do this, but there are very few posts in the Vogue Section here at XDA-Developers.
Having said that, I figured I would create my own "How to Flash Your Vogue"-Thread. This is a multi-step process and I cannot emphasize the importance of following every step down to the "T", that is unless you are looking for a silicone-skinned brick...
Who is this guide for?
*Anyone with a CDMA version of the Touch. [highlight]That means no GSM[/highlight]
*Noobs and Seniors alike.
*People who have trouble flashing their devices.
*Anyone looking for links to more information.
*Curious people in general.
*Anyone willing to get rid of the nasty stock rom and looking for a newer and cleaner OS (notice that I never said more stable, so do not blame me afterwards ).
[highlight]Please keep in mind that there is always a chance of bricking your device with these procedures. I will not be in any way, shape, or form responsible if you damage your device while doing this.[/highlight]
Got your coffee? Alright, let's do this.
Step 1. Preparing the device
As with every phone, you have to make sure that you have the following things done before flashing:
* Battery charged at least 50%.
* All the necessary programs (see next post).
* Instructions handy.
Make sure that you back up all your information (contacts, e-mails, files).... essentially, anything that you would like to keep post-flashing. You can do this via Active Sync/Mobile Device Center or via third party software (PIM Backup is really good)...
You will have to reinstall every last piece of software in your device as it will be hard reset. Some programs may work if installed in a SD card directly, but a lot of them write things to the registry and copy files to the device, which they require to run. Long story short, keep all your cabs and exe files in a safe place so you can restore later if needed.
Step 2. Unlocking the Device (HardSPL)
Unlocking the device is done so that you can flash custom roms in your devices. The unlocker that you are about to download and use was provided by "ImCoKeMaN" at PPCGeeks. If you are interested in the full thread, please click here.
If you have read the above link, you will see two versions of the HardSPL (0.40 and 2.31). Simply use 2.31 as it works fine with most devices.
[highlight]To use this under Windows XP,[/highlight]
1. Connect your device to your computer and make sure it is synced with ActiveSync.
2. Download and extract the contents of the zip file, which is an exe. Let it run to completion. You will be prompted to disconnect and reconnect your device at one point in the process. Do it... don't worry
3. It will look like it is flashing a rom via a RUU. Do not disconnect the device after it is done!!!!!
4. Once it is done flashing, you will see a prompt that says that it will run exitbl. DO NOT DISCONNECT YOUR DEVICE. At this point, open ActiveSync, go to File>Connection Settings> Uncheck "Allow USB Connections". Continue following the on screen instructions and let it finish.
5. Go to bootloader once more to verify that it worked. You should see 2.31 CoKe MFG.
[highlight]To use this under Windows Vista/7 x64 (thanks jitajt),[/highlight]
jitajt said:
connect your device to WMDC (it's not necessary to set up device, just connect without setting up device)
then right click on the 2.31 unlocker and run as administrator
follow the directions, you will get an error about sleep.exe not being compatible with x64 but just hit ok and continue, (you will get about 10 of them)
then just keep following the directions in the command prompt and it will put your phone into bootloader then you have to disconnect and reconnect when it tells you to. and it will flash your phone and reset it. then your done you can close the command prompt and disconnect your phone.
I did it just like above and I have not had any problems.
Do this at your own risk as I am not responsible for your phone
Click to expand...
Click to collapse
Step 3. Flashing your Roms
The time has finally arrived. You sat down patiently through the unlocker and you are now ready to take the leap of faith into what you believe will bring your device to a new level of usefulness (also known as getting rid of that nasty, bloated, stock rom )
The process is relatively simple:
1. Download the RUU package from this post. I am only posting this because some cooks only post the rom nbh files rather than the whole package.
2. Go into the threads and look for whichever rom you prefer. Look at my signature to learn which one I am using. NFSFan (my current one) is by far the best one I have tried so far. You can download it from here
3. Put your device in bootloader mode and connect the device to the computer. [highlight]Once in bootloader, activesync will NOT see the device. If the RUU gives a connection error, try to run it with the devices in regular mode (with ActiveSync connected)[/highlight]
4. Open the Romupdateutility.exe and follow the steps.
5. Once it is done flashing the rom, disconnect it from the computer and hard reset it. To do this, simply hold "Send" + "End Call" +Stylus in the reset hole for about 3 seconds. It will prompt you to erase all the data and restore to factory defaults. Press "Enter", which is the center button in the directional pad. Once it is done, press "Send" to reboot.
Congratulations, you just flashed your first rom for Vogue
Step 4. SuperCID
This step can be skipped if you are not thinking of doing anything as far as your radio (such as flashing radios other than the ones intended for Vogue). This is also used to do other things such as modifying certain important things on your device such as the NV files, which is information that will not be discussed here. However, if you are interested in finding out more, simply google it, there is a ton of information out there.
Anyways, back to SuperCID... here is the procedure (thanks to hpnasik at mobile-files.com for the post)
1. Download the following special rom . This is an Alltel rom with radio 3.37. This was specially prepared to be able to reduce the Security Level of the device to level zero.
2. Download mtty since you will need it. Do not worry if you do not how to use it. You will have a step by step in this guide.
3. Flash the Alltel rom from above.
Now comes the fun part...
4. Disable USB in Connection Settings of Active Sync
5. Boot The Phone holding power button and camera button to enter bootloader.
6. Phone Will Display Serial in Bottom
7. Connect Phone to PC
8. Phone should Display USB instead of Serial in Bottom
9. start mtty.exe
10. Select All Default and Connect to USB in drop down box and Shoot the Following Commands (All Commands are case Sensitive)
11. run command rtask a : After this Command Phone will not Display any thing
12. run command echo_on : even though nothing is shown to screen
13. run command readCID : in Sprint it will display SPCS_001
14. run command writeCID 00000000 : Set CID Value to 00000000 replaces SPCS_001 in Sprint (This make PPC Radio Security Level to Zero)
15. run command readCID : This will Display the Update CID as 00000000
16. run Command retuoR : This will return to Original Boot Loader State
Congratulations, you just SuperCIDed your device. Original thread with the instructions can be found here if you are interested.
Step 5. Flashing your radio.
Now that your device has been SuperCIDed, you will have the opportunity to flash radios that have been ported to this device (ie. there is a version of the 3.42.40 radio for the Titan, which has been ported to the Vogue). There are two ways of doing this:
Way 1: Do it by flashing via RUU (same as with flashing a rom)
Way 2: Flash via microSD card. Simply put whichever radio that you wish to flash in the root of a 2GB or less microSD card formatted to fat32. Rename the radio to VOGUIMG.NBH and put your device in bootloader. The flashing will start by itself.
Way 3 (I know I said two ways...): There are a few stock roms that come with new radios. One of them can be downloaded directly from HTC and it is for the Sprint Touch. This one comes with Radio 3.42.30
The other one is for Bell Mobility and this one comes with Radio 3.42.50.
Why am I giving "Way 3" if the other two options seem much easier?? I have run into the problem where my device would not let me flash other radios than the one that I had. SD card method did not work and the RUU started out fine but quits at 8% rebooting my phone and displaying Error 328 in the RUU on the PC. Anyway, here are the links...
Sprint rom with radio 3.42.30
Bell rom with radio 3.42.50
Verizon Stock Rom
All Shipped Roms (All Carriers) - Thanks conflipper!
All Above Radios zipped
The newer radios perform a little better and give out better GPS signal (faster locks)....
Hang on a sec... did you just say GPS?!?!? But my Vogue does not have a GPS.... It does, just read a little further and be happy
Step 6. Enabling GPS, Returning to Stock, and Carrier Cabs
As I said before, there is a GPS hidden on your device. Now, if you are like me and went straight to the specs of the phone to confirm, you will probably try to call BS on this. Long story short, there are a few custom roms which have this "tweak" already implemented (like the one I am using from NFSFan). If you require some more info, I will post it later...
[highlight]Location must be on or else your GPS will not work. To activate it, go to Settings>Personal>Phone and change the Location setting to ON instead of 911 (thanks for pointing it out, th3lolz)[/highlight]
[highlight]For Verizon Users[/highlight]
br125 said:
For those of you with the official mr1 update from verizon that cannot get their gps working:
My xv6900 came with the official update and I got it working, it involves downgrading to a NON-GPS radio, then back to a gps radio...
go here: http://forum.xda-developers.com/showthread.php?t=533639
now the instructions are going to imply that you must load the unlocker before each flash... bs don't worry about that
1. flash the .40 unlocker
2. flash the non-gps rom (reset before customization)
3. flash the 2.31 unlocker
4. flash the vzw rom (reset before customization)
5. flash any custom rom or android rom
that's it, time consuming, but it works
*ignore the multiple flashing instructions, its completely unnecessary, I've never flashed more than once with no problem ever....
I also suggest keeping the vzw radio, but do as you will, I like the 3.37.38 radio.. ain't broke don't fix it
lastly, just make sure you RESET BEFORE THE CUSTOMIZATIONS RUN...... that is what locks your gps.
good luck!
ps. the verizon radio rom that is in that post is for the "leaked" 3.37.37 radio, I reccomend using the official update from verizon here for the 3.37.38 radio rom instead:
http://www.pcdphones.com/phone_downloads.aspx?bid=95&cid=1&mid=302&carrier=Verizon Wireless
RESET BEFORE CUSTOMIZATIONS
Click to expand...
Click to collapse
[highlight]How to Relock you phone[/highlight]
If, for whatever reason you need to return your phone for repair/replacement, you will need to relock it. To relock your phone, simply run the unlocker 0.40 and flash the stock rom of your carrier.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker.exe
[highlight]Carrier Cabs[/highlight]
Thanks to Codybear for gathering all of the cabs with settings for various carriers. But since the link went down, here is another one courtesy of LMiller1708
https://sites.google.com/site/vogueroms/vogue-files
This information was only gathered by me and I take no credit whatsoever other than trying to put it in a one stop thread. Thanks to the following people
Shadowmite
ImCoKeMaN
mindfrost
NFSFAN
Codybear
joshkoss
and a bunch of people that were involved in developing all this...
Thread sticky'd as requested
Peace,
Josh
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
dwigginstm said:
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
Click to expand...
Click to collapse
How exciting!! My first victi...erh patient
Did you put the device in bootloader mode? If you did and it is connected to the PC, you should see USB on the screen of your device. Also, do you have ActiveSync on your XP machine? You will need it for the drivers on this step. Changing USB ports sometimes help as well. And one last thing, do not use a USB hub, go directly through the USB ports in your computer. Good luck!
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
yes i have activesync set up with the phone and pc, but when i put the phone in bootloader mode and connect it the pc recognizes it but not activesync. is there another program i can unlock the phone with?
dwigginstm said:
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
Click to expand...
Click to collapse
Do not worry about ActiveSync. While you are in bootloader, the device is not running WM, which is why your computer only sees it as a USB device. This is perfectly fine. ActiveSync will not recognize it.
Please, follow the instructions in my post for unlocking. Read it thoroughly and try to understand it, else you will end up bricking your device.
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
dwigginstm said:
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
Click to expand...
Click to collapse
that is a message in the RUU. do not pay attention to it. good luck...
so i finally got the unlocker to start and it begins the ten minute process and stops then show a 262 error code ive done this over and over again
Let's go from the top. I just saw the message that you were talking about. The unlocker does ask for ActiveSync as you pointed out and it is asking you to connect the device to the computer. Then it asks for you to press any key when that is done. So, try that and you should see the word "initializing" with a dotted line getting longer for about 20 seconds. Do that.
The RUU will start up afterwards. The prompt will tell you that it is going to flash a new SPL, and if I am not mistaken that is where you are getting stuck.
Just out of curiosity, which version of the Vogue do you have? (Alltel, Bell, Verizon, Sprint, US Cellular)?
no internet
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
terrancextc said:
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
Click to expand...
Click to collapse
You downloaded a cab. Simply put it in your SD card and run it by tapping on it. Don't unzip it...
Unlocker is not 64 bit compatible... grrr....
Please help!
My HTC TP2 freezes at start up with the black screen and the Touch Pro2 Logo and some details in red at the bottom:
B 80
R 4.49.25.17
G 61.44tc.25.32U
D 1.86.67102
No USB connection can be established.
What happened:
1. Tried to update from original WM 6.1 to WM 6.5 by using the official HTC ROM update utility. Seems like USB connection broke during update and update freezed at 42%. Update utility process has stopped by itself (no process visible anymore in the Task Manager).
2. Restarted phone and multicolor screen appeared and stayed. After connecting with USB cable again "USB" appeared at the bottom. Started again the HTC ROM update utility which recognized the phone and started the update process again, but stopped at the beginning with an error message stating something like the ROM is broken.
3. Restarted again (by removing the battery and hit power button) and state reached like described above (HTC TP2 freezes at start up with the black screen and the Touch Pro2 Logo and some details in red at the bottom).
4. Performed a hard reset but did not help.
What can I do to bring the phone back to life?
So you can't or can get in the colored screen now? (the boatloader)
And it's kind of normal that their nothing happens after the tp2 + red information screen, this since their is no rom to startup.
EDIT
Is it possible to tell exactly what error you got?
EDIT
Try to hard reset your device, do you know how to do this?
If not this is how to do it:
To perform a hard reset
1. With the device turned off, press and hold the TALK/SEND, END and POWER buttons until you see this message on the screen.
"This operation will delete all your personal data, and reset all settings to manufacturer default. Press VolUp to restore manufacturer default, or press other keys to cancel."
2. Release the TALK/SEND, END and POWER buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
Source: http://forum.xda-developers.com/showthread.php?t=523083
This is just what worked for me..
Had the same issue on my tp...
Hope it will work for you.
Did already the hard reset - but this did not help as nothing changed!
One further info: whenever I insert the battery the device automatically starts up - until it freezes again at the start up.
Can someone please help?
It's normal that the device starts up when the battery is plugged in...
But this is just what I know out of my own experience.
So sorry I can't help you farther.
EDIT
Did some research you might want to try to flash your phone by micro sd... (not for sure if it helps but by some people it did work)
Read the tread about flashing at the top of the rhodium section and you know how to do it.
Did another trial: downloaded and copied a RHODIMG.nbh to the micro sd card, inserted it again and pressed volume up at startup -> colored screen appears shortly, then switches to a white screen telling "Loading..." in blue font color, but nothing more.
Is there anybody out there who can help?
Do I need a specific RHODIMG.nbh to make this approach working? I didn't flash this device before, so it has been still in the original manufacturer's state.
frieder01 said:
Did another trial: downloaded and copied a RHODIMG.nbh to the micro sd card, inserted it again and pressed volume up at startup -> colored screen appears shortly, then switches to a white screen telling "Loading..." in blue font color, but nothing more.
Is there anybody out there who can help?
Do I need a specific RHODIMG.nbh to make this approach working? I didn't flash this device before, so it has been still in the original manufacturer's state.
Click to expand...
Click to collapse
suppose 2 press down volume not up after soft reset
This may help,
Try entering bootloader by switching off device then switch back on holding down the Vol down key.
If you can enter bootloader this way then you wil be able to flash from SD card following the instructions from here
http://forum.xda-developers.com/showthread.php?t=550540
if you want to flash the Official update from HTC you can extract the Nbh from the Exe file you downloaded from them, just use winzip, Zzip or Win RAR to extract the contents from the Exe you are looking for RUU_signed.nbh..follow the above thread instructions to change the name of the file to RHODIMG.nbh.
I DONT KNOW IF YOU NEED TO HARD SPL FOR THIS..Probably better to do it than not. Can Anyone Confirm???
i hope this helps
Device is up and running again !
Could enter bootloader mode and tried first to install again via the official HTC installer -> worked!
Thanks a lot for your support!
great news welldone Bro and welcome to the forum!!!
osrix25 said:
This may help,
Try entering bootloader by switching off device then switch back on holding down the Vol down key.
If you can enter bootloader this way then you wil be able to flash from SD card following the instructions from here
http://forum.xda-developers.com/showthread.php?t=550540
if you want to flash the Official update from HTC you can extract the Nbh from the Exe file you downloaded from them, just use winzip, Zzip or Win RAR to extract the contents from the Exe you are looking for RUU_signed.nbh..follow the above thread instructions to change the name of the file to RHODIMG.nbh.
I DONT KNOW IF YOU NEED TO HARD SPL FOR THIS..Probably better to do it than not. Can Anyone Confirm???
i hope this helps
Click to expand...
Click to collapse
For future info, from what I have gathered you must hardSPl for all ROM flashes. If the ROM you flash is the stock ROM, you can also revert your SPL to stock. For any other ROM, you must leave your device hardSPL'd.
Hope I helped.
how were you able to connect the phone with the pc. i seem to have a similar problem but am finding it difficult to connect the phone to the pc. i have activesync installed but cannot connect to the phone
osrix said:
This may help,
Try entering bootloader by switching off device then switch back on holding down the Vol down key.
If you can enter bootloader this way then you wil be able to flash from SD card following the instructions from here
http://forum.xda-developers.com/showthread.php?t=550540
if you want to flash the Official update from HTC you can extract the Nbh from the Exe file you downloaded from them, just use winzip, Zzip or Win RAR to extract the contents from the Exe you are looking for RUU_signed.nbh..follow the above thread instructions to change the name of the file to RHODIMG.nbh.
I DONT KNOW IF YOU NEED TO HARD SPL FOR THIS..Probably better to do it than not. Can Anyone Confirm???
i hope this helps
Click to expand...
Click to collapse
is it possible to connect to active sync in bootloader, cos my phone cannot even boot, it freezes up with a white screen and htc logo.
After entering bootloader you can flash either way,either by ruu package provided by your ROM's maker or running official ruu release or if you have the renamed file on the root of your sd card....I never use sd card flashing and have never had a failed flash...If in bootloader it will not connect with activesync,but device should be recognized by ruu.exe
WC
I'M NOT RESPONSIBLE FOR ANY DAMAGE YOU DO TOU YOUR PHONE HOWEVER I WILL DO AS MUCH AS I CAN TO HELP YOU FIX IT
GSM ONLY!!! NO CMDA USERS
Note: This TUT was written from my expeience with a DIAM100!!! I do not know if the files included in this TUT are compatible with Diamonds other than the 100
This TUT will cover complete flashing of everything on your Diamond, I wrote this cause it took me 2 hours to get my Diamond hacked so i could reap the benefits of the community:
1. Hard-SPL - Post 1 & 2
2. Rom - Post 3
3. Radio - Post 3
__________________________________________________________
Note: Doing this will Hard Reset your phone, any data not on your 4GB internal will be deleted!!! If you want to make a backup, I recomend you use SPB Backup Free Trial and save the EXE created to your 4GB
__________________________________________________________
What Is Hard-SPL?
Hard SPL in computer terms is the BIOS, it lets you recover your device if you incorectly flash your device. This bootloader was developed by OliNex and comes in to flavours Dev and Signed, i have attached the files at the bottom of this thread. It is essential if you want to put cooked material on your device. if you install this IT WILL VOID YOUR WARRANTY, how ever, you can still flash the Stock SPL back should your diamond need repairing.
How Do I Flash It?
If you want to restore the stock SPL, I recomend you make a note of which version you have, this is easy and simple
1. Reset your Diamond
2. Press and hold the Volume Down button on left side of your device, it shold display some numbers and some text, the number should be between 1.23 and 1.37
3. To get back to Winmo, simply press the reset button
With the OliNex SPL's, all you need to do is charge your Diamond to 50% or more, connect via activesync / Device manager on a 32 BIT WINDOWS SYSTEM (XP Only) !!!
Create a new folder with no spaces in it, E.G "C:\\Diamimg_OliNex" , unzip the files you have downloaded from the bottom of the page into this new folder
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then, with your Diamond connected, run "RomUpdateUtility.EXE" and follow the on screen intructions
IF YOU UNPLUG YOUR DIAMOND WHILE THIS APPLOCATION IS RUNNING, YOU WILL BRICK YOUR DEVICE!!!
The computer should be displaying a progress bar, it should jump from 0% to 100%
IT WON'T TAKE 10 MINS LIKE IT SAYS IT WILL
A message should appear sayying that your phone has been sucessfully updated
When you see this, Congrats, You have flashed Hard-SPL to your phone
To confirm this, simply repeat the steps you did to check your Stock SPL, It should say, 1.4* OliNex
Flashing back to stock SPL is in the next post
Note: Doing this will Hard Reset your phone, any data not on your 4GB internal will be deleted!!! If you want to make a backup, I recomend you use SPB Backup Free Trial and save the EXE created to your 4GB
__________________________________________________________
To flash back to the Stock SPL, YOU MUST FIRST FLASH THE STOCK ROM AND RADIO, SPL MUST BE FLASHED LAST!!! You will also need the SPL pack which is included in the first post, when we flashed Hard SPL, I mentiod the number of your Stock SPL, if you still have it you can the Stock SPL. This useful because if your supplier is trying to fix it, and bumps into bootloader, it will say "1.40 OliNex", and he will say "This has voided your Warranty". If it says "1.37 HTC" he will say "I will repair it now". Anyway, to replace the Hard SPL, there are two ways. If you have the Un-Signed SPL, you have to use the file "Un Signed SPL Restorer", when you have chosen your Stock SPL, extract the SPL Restorer to a top level of a Local HDD, copy the SPL file into this folder with the other files. Then rename it "RUU_Signed.NBH" without the quotes. Run "RomUpdateUtility.EXE" and follow the on screen intructions
IF YOU UNPLUG YOUR DIAMOND WHILE THIS APPLOCATION IS RUNNING, YOU WILL BRICK YOUR DEVICE!!!
The computer should be displaying a progress bar, it should jump from 0% to 100%
IT WON'T TAKE 10 MINS LIKE IT SAYS IT WILL
A message should appear sayying that your phone has been sucessfully updated
When you see this, Congrats, You have flashed Stock-SPL to your phone and deleted Hard-SPL Un Signed
If you have a signed OliNex SPL, the restoration process is slightly different
The proces is exactly the same except instead of using "Un Signed Hard SPL Restorer", you simply download "Stock Restorer For Signed"
Flashing ROM's
Ok, this is the easy one
There are several methods of flashing ROM's, Using RUU, MTTY and my personal fave, Internal Storage Method, I will cover all of these in this post
Some ROM's I recomend
1. The latest of Winmo products, L3V5Y's 6.5.3 Build 28*** ROM, it's fast, stable and light! Only a 60MB download, which is pretty good. This requires Unsigned Hard SPL
2. GEN Y's 6.1 Manila Rom, this rom is very stable. It hasn't got the 6.5 ROM in it, but it has the latest version of Manila / Touch Flo (The Fancy Interface That Is Installed On The Stock ROM)
1: Internal Storge
This is the easiest, quickest and safest way to flash ROM's, the ROM is a single file (*.NBH), you need to rename it "DIAMIMG.NBH" without quotes
then follow these steps to copy over
1. Plug your phone into your PC
2. Select "Disk Drive"
3. Copy DIAMIMG.NBH to the top level of your phone
When this has completed copying, you must reset and hold Volume down and the Back button, you will see a quick Tri Colour screen and then you will see "Loading" the screen will change and it will say "Press Power Button To Start Update Image", after you press the power button a progress bar will appear at the bottom of the screen, when it has completed, it will say "Update Sucessful", peform a soft reset and enjoy your new ROM!
2: MTTY
MTTY is HTC app that lets you modify the contents of your devices ROM from a command script, you can't actually flash a rom with it, but you can prepare your device with it, if you only flash with internal flash you may get a bad flash, for example a read only file may have copied incorrectly and corrupted the ROM memory. MTTY will format and fix this.
FOR VISTA + WIN 7 6 BIT SYSTEMS, SEE BOTTOM FOR DRIVER INSTALL OTHER WISE YOU MAY DAMAGE YOUR DEVICE!!!
To prepare your Diamond for PC or Storage flashing:
YOU MUST HAVE HARD-SPL ON YOUR DIAMOND
Internal:
After you have downloaded your new ROM, copy it to your Internal Storage and rename DIAMIMG.NBH like you did with the method above. You need to download MTTY which is attached to this post, place your device in bootloader (Reset and Vol Down) Run MTTY after extracting to a top level of a local HDD, a list of options should appear, change it from Com1 to USB, if USB is not on this list, try disabling "Allow USB Connections" in activesync and restart MTTY, when you have selected USB, MTTY will start, just click ok when a option window pops up, after this, wait for a window to pop up and press Enter on your PC keyboard, CMD or USB should appear. I will write the commands then a line below I will write what they do
set 14 0
This tells MTTY to reboot when complete
task 29
MTTY will format your ROM
NOTE: after typing task 8 (Below), very quickly unplug USB and hold down Volume Down and Back to trigger flash
task 8
Reboot Device
PC:
Same Layout As Above
set 14 0
This tells MTTY to reboot when complete
task 29
MTTY will format your ROM
NOTE: after typing task 8 (Below), very quickly unplug USB and hold down Volume Down to trigger Bootloader Mode
task 8
Reboot Device
Plug back into PC, serial should change to USB
Run RUU.exe (Included With Rom) and follow on screen steps (This one will take 10 mins)
MTTY On X64 Bit Systems
Before you do MTTY with a Vista / Win 7 64 Bit system, you must install drivers
First, disable driver signing HERE
Then download and install drivers from HERE
RUU
Note: if the rom is an *.EXE, you dont need to do this as that Rom is an RUU
1. Download your Rom
2. Download the "DiamondCustomRUU.ZIP" from my next post
3. Copy both to the same folder
4. Connect phone via ASync or WMDM
5. Run the Ruu .EXE
6. Follow the steps in my next post
Radio:
This bit is about flashing your radio, people flash their radio to get better reception in the area, if your diamond was sold to you as a TRI Band phone, you can upgrade it to QAUD Band for free
THIS DOES NOT UNLOCK YOUR RADIO FOR USE WITH OTHER SIM CARDS!!!
There are plenty of Radios floating around, one recomended around the forum is 1.00.25.05, this enables QUAD Band, use little power and gets great reception. You can check your radio when your phone is booting, it's the first line of red text. If you have radio version 1.00.25.05, or if you get good signal and good quality voice calls, you don't have to update it
DO NOT TRY AND FLASH A RADIO FROM ANOTHER PHONE!!!
How To Update:
First download a Radio from here
Then download RUU from the bottom of this page
Extract both to the same folder
Run RUU, Check the box and click next
After you have done the things listed in the picture, tick the checkbox and click next
Click Update
The RUU will tell you what version you are going from to what version you are going to
Click Next
DON'T UNPLUG YOUR DIAMOND OR DO ANYTHING ON YOU PC WHILE THE RADIO IS UPDATING
When PC reaches 100% DON'T UNPLUG YOUR DIAMOND, Click finish and wait for your Diamond to reset
Acknowledgements
OliNex - Hard SPL Is Briliant
MysticGenius - The Definitive MTTY Thread
Tom_Codon - CustomRUU Will flash any thing and everything
Modmydiamond - Thanks for the pics
Microsoft - Winmo Isn't Great Out The Box, But Is A Brilliant Software Base, Without You, We Would All Have to Get iPhones
The XDA Community - Stuff I Have Just Picked Up From Browsing This Great Forum
Ralphusion - Links For X64 Systems Cause I'm To Lazy To Find Them Myself
ElCondor - Thanks For The Wiki Link
And Finaly: HTC - Now Where Do I Start?
errrrrr
this is a waste of space. everybody knows these stuff. mods!!! do we really need this?
bevoc said:
this is a waste of space. everybody knows these stuff. mods!!! do we really need this?
Click to expand...
Click to collapse
when i tried to get custom on my diamond, it took 2 hours, this tut by tnyynt is good, but complex, i had to read 3 times before I fully understood
bevoc said:
this is a waste of space. everybody knows these stuff. mods!!! do we really need this?
Click to expand...
Click to collapse
How about you shut up and don't read it if you are so bothered by it? This is a forum, and anyone can post whatever they like, as long as it is within the rules.
Good job, Badwolve1!
leonatan25 said:
How about you shut up and don't read it if you are so bothered by it? This is a forum, and anyone can post whatever they like, as long as it is within the rules.
Good job, Badwolve1!
Click to expand...
Click to collapse
many thanks
Great work, this is really usefull for people having trouble getting their Diamond updated and flashed.
When I came here I really needed something like this, because all information was cluttered all around the forum. Now we have it at one place.
bevoc said:
this is a waste of space. everybody knows these stuff. mods!!! do we really need this?
Click to expand...
Click to collapse
And you are even asking for the mods to clean this...
Go think before you post these kind of answers.
Badwolve1 I think it's a good idea to put this in the wiki,
If you don't know how it works I can do it for you with a link to this thread.
This is good work and should be rewarded, we should have these guides for every device!
Having this information all in one thread is really a relieve, tx for your efforts Badwolve!.
Maybe this forum will end up now with a little less ' help....my diamond is bricked' threads, so no waste but gain of space huh
Badwolve1 said:
Flashing ROM's
1: Internal Storge
This is the easiest, quickest and safest way to flash ROM's, the ROM is a single file (*.NBH), you need to rename it "DIAMIMG.NBH" without quotes and copy it to the top level of Internal Storage. When this has completed copying, you must reset and hold Volume down and the Back button, you will see a quick Tri Colour screen and then you will see "Loading" the screen will change and it will say "Press Power Button To Start Update Image", after you press the power button a progress bar will appear at the bottom of the screen, when it has completed, it will say "Update Sucessful", peform a soft reset and enjoy your new ROM!
Click to expand...
Click to collapse
The Loading screen stands there for "forever". I've been waiting for more then 20 mins and the Loading... screen is not changing. What seems to be the problem?
Mtty and windows 7 (x64)
Badwolve1 said:
2: MTTY
MTTY is HTC app that lets you modify the contents of your devices ROM from a command script, you can't actually flash a rom with it, but you can prepare your device with it, if you only flash with internal flash you may get a bad flash, for example a read only file may have copied incorrectly and corrupted the ROM memory. MTTY will format and fix this.
XP ONLY!!!
Click to expand...
Click to collapse
Badwolve - Good to see your consolidated tutorial. Just wanted to share that mtty works directly with Windows 7 (x64) as well now. There are two possible methods for this (tried both and both work):
Eugenia's signed x64 drivers
Disabling/Ignoring driver signing using gpedit
djandreski said:
The Loading screen stands there for "forever". I've been waiting for more then 20 mins and the Loading... screen is not changing. What seems to be the problem?
Click to expand...
Click to collapse
Hmm, seems like your device hasn't been hard spl'd. Can you confirm that you've done so?
My device is HardSPL-ed I've installed 1.30 OliNex, and on the three color screen there is a text that says "1.30 OliNex" so it is spl-ed
And when I try to Flash from PC the custom RUU and phone bar are stuck at 0% and after a wile i got 262 error on ruu. see the picture.
djandreski said:
My device is HardSPL-ed I've installed 1.30 OliNex, and on the three color screen there is a text that says "1.30 OliNex" so it is spl-ed
And when I try to Flash from PC the custom RUU and phone bar are stuck at 0% and after a wile i got 262 error on ruu. see the picture.
Click to expand...
Click to collapse
You can check this thread http://forum.xda-developers.com/showthread.php?t=409425 for more info on these errors
ralphusion said:
Badwolve - Good to see your consolidated tutorial. Just wanted to share that mtty works directly with Windows 7 (x64) as well now. There are two possible methods for this (tried both and both work):
Eugenia's signed x64 drivers
Disabling/Ignoring driver signing using gpedit
Click to expand...
Click to collapse
]
Thanks for replying, I did know that MTTY will work with 7 + vista, x86 + x64, i just didn't want to make it all complicated
i will put how to do 64 7 + vista in somewhere, thanks for the links
Badwolve1
djandreski said:
My device is HardSPL-ed I've installed 1.30 OliNex, and on the three color screen there is a text that says "1.30 OliNex" so it is spl-ed
And when I try to Flash from PC the custom RUU and phone bar are stuck at 0% and after a wile i got 262 error on ruu. see the picture.
Click to expand...
Click to collapse
May i ask what rom you are using?
You will probably need Dev Hard SPL as not many Roms are signed by OliNex, i this problem persists ater install of Dev SPL, Try internal flash
Good Luck
Badwolve1
Badwolve1 said:
May i ask what rom you are using?
You will probably need Dev Hard SPL as not many Roms are signed by OliNex, i this problem persists ater install of Dev SPL, Try internal flash
Good Luck
Badwolve1
Click to expand...
Click to collapse
I started a new thread http://forum.xda-developers.com/showthread.php?t=611146 where the problem is detailed explained.
Please review that thread and help me if you can.
this is great!! but im kinda confused with the part where you said
the top of your internal storage?...
do u mean the mobile device when it pops up in ur pc or removable disk?.....thnks!