Hi guys.
I was using the installed the FInixNOver 3.0.1 ROM onto my SPV M700 and it was great. I've had it for about 2 weeks without any problems.
Last night I looked at my phone, only to realise that it was completley dead. This didnt shock me to much because the battery was running low, and i decided to let it die completley before recharging it again.
I charged my phone overnight and switched it on this morning, but the phone would freeze at the 'FInixNOver' splash screen (the numbers at the bottom of the screen would appear overlaying the splash, but the phone wouldnt go pass this point).
The only way to turn off the phone from this state is to eject the battery. I have tried removing the sim card, turning it back on in as many ways as possible but to no avail. I am able to get to the TriColor test screen (im running IPL-0.50 / SPL-1.30.Olipro) but with all the custom roms available, they all use the ROMUpdateUtility which requires the phone to have established an activesync connection initially (but this would mean my phone would have to be 'on completley' - so this is catch 22.)
For the record, my phone/battery died while my wired handsfree was attached (dunno if thats of any interest to anyone or the rom baker).
But it looks like the only way i'll be able to flash my phone is by finding a way to install the .nbh file without using the RUU method. Because I can put my phone into test mode manually.... any help or guidence would be very much appriciated.
Thanks.
Ok can you get it into bootloader? power/camera buttons and reset?
sorry didnt read fully.
right get your device into bootloader first,
then open active sync (are you using xp)
then open connection settings and disable usb connection,
put your device into bootloader mode, then run any rom upgrade, i prefer the WM6.1 pdaviets from HERE (Username: PDAVIET / Password: pdaviet)
Your pda does not need active sync with ruu's, so no catch 22. if you turn off usb connection in active sync, you can still run ruu and it will be recognised, unless you are using vista, where you need to change your HTC SYNC drivers.
Thanks for your quick response...
Yes I can get into boot loader using the power and camera buttons (or holding the power and camera buttons when resetting the phone)...
When the phone is in boot loader mode, active sync doesnt even detect the phone anyway, but nevertheless, I have followed your instructions and disabled the USB Connection. (BTW, yes i am using XP)
The phone is still in boot loader mode, so now i try and execute the ROMUpdateUtility.exe and go through the steps, at the 1st step i tick the tickbox and click next, and the 2nd step i tick the tickbox and click next. (this step says DO NOT enter the bootloader manually? - but i have havent i?) anyway, when i click next, it says... "Verifying the information on your Trinity... Please Wait..." for about 10 seconds, and then i get a message "ERROR [260] : CONNECTION"
What am i doing wrong?
Huumm.. why dont you flash your phone throw the sd card??
Read this link:
http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
try to flash your phone with some official rom and after that flash it with any other you want!
manos_23 said:
try to flash your phone with some official rom and after that flash it with any other you want!
Click to expand...
Click to collapse
I would recommend this option above, to be safe, i usually get them error messages when the battery is below 50% or sometimes i try it again and it works. it does state do not manually enter bootloader but i always do it this way.
also make sure active sync is not still running in taskmanager under the alais: wcescomm.exe and WCESMGR.exe, end them both.
I've just tried using an official ROM, but the problem still occurs with the 'connecting'. It doesnt seem that the computer picks up a connection to the phone whatsoever.
Should i be concerned that at the bottom of the bootloader screen it says "serial", is this correct?
Im starting to get annoyed now.
Bye,
the bottom of the sreen mast say "usb" not serial.
it seems there is a problem, if it states serial. as it should say usb. try THIS
Seems like the problem was that my USB lead was loose and made a bad connection, hence why the bootloader showed 'serial' and not 'usb'... as soon as i wiggled it and heard the 'connection noise' in windows, i knew i was good to go, and so using the RUU worked fine to reupdate my phones ROM.
Thanks for your help.
My only question is that why did it happen in the first plave?
WIZZKID - I just saw your post here now. I have to tell you that I also saw "SERIAL" at the bottom of the bootloader screen and not "USB". As I said I returned it to get another phone but maybe I will try something else for now instead of a P3600i. I will monitor your thread to see how it turns out for your phone, because it seems that we have the same problem.
if you see "serial" instead "usb" your problem is in the usb cable, usb port from your computer or in the usb connector from your trinity!!!!!
I was having the same problem that you have!! my problem was from my usb from mine trinity!! see if the conector is at good conditions !!!
Well as some of you may know, I got my Trinity replaced for sticking at the WM splash screen after a few days. This second one - I have had it ONE night - and the same thing has happened with incomplete booting. This time I have been trying all night to flash the phone to an official ROM, but I cannot do it (apparently) because I can't establish a connection via ActiveSync. When I stick the data cable in while in bootloader I see SERIAL replaced by USB and when I try the flash I get a "270" error (cannot connect to phone) and the phone re-boots to the sticking plash screen. What should I do now?
ladies and gentlemen...
we've got a lot of mixed messages in this thread.. please make sure you're posting the right thing. no need to disable USB when manually going in to bootloader to flash (at least in xp).. Also, you can ignore the part of the RUU that says 'do not manually enter bootloader' (you should really read the guide on my site)
foxuniform- can you please give some details..
1) are you running xp or vista
2) have you flashed hard-spl? if so what version?
in the mean time, try a couple of things.. first, flash hard-spl (even if you already have it, but from the sound of it i think you don't have it on your device).. if that works, try to flash an official ROM. Can also try to use splxploit, then flash hard-spl, and then flash official ROM (there's a guide on my site if you're unsure)
please post your results
*edit*
here are the steps for SD card upgrade, but i HIGHLY recommend flashing Hard-spl first..
try to do it from SD card. how?
Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract (http://www.cabextract.org.uk/) .
Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
When flashing completes soft-reset your device.
Make sure your SD has FAT32 and has no label. There have been reports that if SD has a label the bootloader can not access the TRINIMG.nbh
racerx_ I have carefully read your response and suggestions, and thanks for your expertise input on the matter. I am fairly new to this stuff so read below carefully as you may find errors in the way I tried to go about doing what I was hoping to accomplish.
First let me answer your questions. I am running Windows XP. The phone is in it's completely natural state in that I have not flashed it in any way. The ROM I was TRYING to flash to the phone while it was not starting properly (this is where I manually entered bootloader) is an official ROM from the HTC website (please note everyone that when I registered my P3600i on the HTC website it came up as the Dopod 810). Anyway, that never worked. ActiveSync never detected the phone (and I guess that's the reason I could not do anything as far as flashing goes). I HARD-RESET my P3600i and it booted normally. I re-installed all the stuff I had on it, from memory card to various .cab files, and the phone is working beautifully thus far. I will report if anything funny happens again.
I have to ask you racerx_, if I CAN flash hard-SPL on the P3600i according to the lovely guide on www.trinityguides.info. I have been of the opinion that things don't work for the P3600i as they did for the P3600, and that has been echoed by many P3600i users on this forum who are ready and waiting to try out some cooked ROMs (myself included).
For the sake of record, my phone is running rom version 3.00.707.17 and radio version 1.46.00.11. I patiently await your response.
woaaahhh..
i didn't notice the 'i' in your previous post... yeah, as far as i know, these ROMs are not flashable on your p3600i.. sorry..
**correct me if i'm wrong somebody**
Yeah I kinda thought that would be your response. By the way - do you think that this phenomenon of sticking at the Windows Mobile splash screen (both the P3600 and P3600i models apparently) has anything to do with something users do with the devices, or you figure it's an inherent software glitch of some sort? I am wondering if I should try a different model or hold on to my P3600i? Hope it's not something that'll happen again - I fly for a living and it's not gonna be good to have the thing screw up on me away from base - I really count on it for everything from casual keeping in touch on Messenger to viewing my work schedule. I love the Trinity though - it's one of my all-time favourite HTC phones.
hmm... i don't think its inherent in the Trinity.. (not a hardware issue.. in my opinion)
its been a while since i followed the posts on it, but always seems to be software related.. sometimes ROM-specific problem. Personally, i've probably flashed as many ROMs as anyone and the only time i ever encountered problems was with the official HTC WM6 ha.. go figure.. I think ppl did find that hard resets before and after flashing are helpful as well..
i love my trinity, and there's not much else on the market to make me want to trade it in (is it just me, or have pda's kind of stopped getting cooler).. i'd stick with it..
Related
Firstly I would like to say thanks to this site and the trinityguides.info site for the great work people have being doing and making available to everybody, it is great being able to use my trinity with wm6, keep the good work going!
Now the issue I seem to be hitting the same "error [260] connection" every time I attempt to update anything on my Trinity. I have followed the advice on the trinityguides site regarding being stuck in bootloader mode to no avail, and I can't seem to find anything in the posts on the xda site which will rectify the issue.
Previously I have been able to update to AX3L v2.8.01 version without any problems, but I decided to update to sammy's ultra light, it initially kicks into des' crashproof sspl, but then it can't connect to the pc. even when I manually enter olipro's hard-spl it does the same. I have tried to re-install hard-spl, but can't. Disconnecting the usb option in the activesync settings doesn't do anything either. Does anybody have any suggestions for me please?
I am not even too sure if my trinity should have both Des' crashproof and hard-spl on it at the same time? Could someone advise me on whether this is alright please?
the tech details:
Trinity
AX3L_OS_v2.0.8.2
radio - 1.46.30 (even though it doesn't say this in the device info, or boot screen after soft reset)
Home PC - XP (just in case)
Did you also try flashing it again, the ROM I mean. I have this error also but as soon as I execute the ROM flash again it finds the device and starts flashing:
http://forum.xda-developers.com/showpost.php?p=1449597&postcount=2
I am assuming you mean flash with the new ROM, sammy's in my case?
yes, as described in the link I posted before. As soon as the error occurs, do not touch the phone, leave it, just start the ROM flash procedure again. (execute ROMUpdateUtility.exe)
No, I am in the same situation. The first attempt puts the device in 'ipl-sspl by des' bootloader mode then after about 10 seconds or so the error[260] is displayed on the pc. If I exit the ruu app and attempt again, nothing new happens on the trinity (i.e. it is still in Des bootloader) and the message is displayed again.
the thing is that when it first goes into des bootloader mode, the white strip doesn't have any text in it. If I pull the usb cable out then put it back in, 'serial' is then displayed in the white bar, but I am still in the same situation as before.
What operating system en activesync are you using?
On the PC I am using XP and Activesync 4.5
Check your connection settings to accept USB connections. Also, try using Hard-SPL 1.30 before flashing the ROM again.
deejacker said:
the thing is that when it first goes into des bootloader mode, the white strip doesn't have any text in it. If I pull the usb cable out then put it back in, 'serial' is then displayed in the white bar, but I am still in the same situation as before.
Click to expand...
Click to collapse
In your PC, try another USB connection.
BLOODY HELL!!! It is the simplest things which we often forget to try. Thanks Jotam for pointing out an obvious point, it must have needed a re-plug of the usb cable into another port for the pc to pick up the device again. I will remember that for future updates so I don't make a dumb ass of myself again. Thanks guys/gals.
Vista
Using Vista? if so which version?
Hi I asked this question yesterday, I am a noob :-[ but the only difference is I'm using Vista Ultimate.
Just for others who have the problem.
When you replug into another USB port (Luckly I've got two on my laptop..)
I used the Vista drivers from TrintyGuides and bingo !
now I try and flash a WM6.....English or Italian...maybe French.
Thanks for the help I keep you posted.
Richard
It works
Now to discover the joys of WM6 after only having WM5 for two weeks....
/i am getting the same only rom update 3.14.4.1 now sees the phone..
has the device name changed???
evene exploit no longer sees the phone
sorry, can you be a little more clear.. what ROM are you flashing, and what exactly is happening?
by the way... i thought error 246 was the connection error... am i mixed up? which is 260?
This seems to be on any rom bar the Dopod roms
and it says 260 connection error
Error 260 connection error - the phone is not going in to bootloader mode - and the RUU cannot seem to initiate communication with the phone.
I'm getting this a lot recently trying to flash.
However, Hold the power and camera buttons while resetting with the stylus (keep them buttons held down).
When you get to the bootloader - plug the phone in - wait till you see the USB at the bottom of the bootloader screen - then run the RUU again - it WILL work - every time.
I used to get this error message alot. sometimes the programs you install don't allow you to update even if you force the phone into bootloader mode so you have to hardreset the device and then upgrade.....hope this helps
htc diamond stuck
T-Rob said:
yes, as described in the link I posted before. As soon as the error occurs, do not touch the phone, leave it, just start the ROM flash procedure again. (execute ROMUpdateUtility.exe)
Click to expand...
Click to collapse
hi ,
my htc diamond stack, no respond on the screen i try to do hard reset with tree buttons but its not working, nothing happaned, screen stay home screen with the time and not responding touching the screen at all
please emergensy help
I did a rom upgrade on an hx2110 - installed successfully, but now the only thing I can get the pda to do is go into Pre bootloader mode (i.e. Pre-BL 1.00.02 blue screen). SO I tried the universal bootloader method - makes it all the way to the flashing portion but then does NOTHING - the terminal simply sits there saying "ready" and does not upload anything - the program sees the correct communication port (ie. usb01 or whatever). HOW do I force an upload???
Thanks!
Rusty
On another note - I had purchased a working 2110 with a good mobo to replace this one if the flash is not repairable - is that a difficult procedure? Unfortunately, the 2110 I purchased was not working, but this may still be in the books at a later time, so some info would help.
Thanks!
Rustmonkey said:
I did a rom upgrade on an hx2110 - installed successfully, but now the only thing I can get the pda to do is go into Pre bootloader mode (i.e. Pre-BL 1.00.02 blue screen). SO I tried the universal bootloader method - makes it all the way to the flashing portion but then does NOTHING - the terminal simply sits there saying "ready" and does not upload anything - the program sees the correct communication port (ie. usb01 or whatever). HOW do I force an upload???
Thanks!
Rusty
Click to expand...
Click to collapse
Rusty,
You are so lucky that I experienced this problem and solved it on my own. You did not specify what ROM you were loading, but here is the fix:
First you need to get another pocketpc, hx2000 series like yours that is working.
Put that device into white screen bootloader or pre-BL mode (depending on which device you got to borrow)
Ensure that the battery on that device is 100% charged.
Run the original ROM upgrade for the ROM you wish to install (use PDAViet if it's WM6 and use the HP SP32408 to Run it)
Hit all the Ok screens until it brings you to the one that has the "UPDATE" button.
Remove the working Ipaq from the cradle and place it's 100% battery in you own.
Put your Ipaq into pre-BL mode and put it on the cradle. Press the calendar button to activate the usb drivers.
Once it says "USB", Hit the "UPDATE" button and it will load the proper ROM to your IPaq.
When It is done, perform a hard reset by formatting the PS on the device.
Voila!! Your Ipaq is Un-Bricked!! Put in your original battery and charge it up!
Enjoy!!
Bless...
hi Rustmonkey,
i have the similar things - i made my hx2110 brick when i flashed it with a different language ROM, it went 100% when i flashed the ROM but didn't work at all after that.
the problem is i can get it in the bootloader mode after trying many ways, at the same time the pc can't find any USB device at all.
how to make it work again?
thanks.
reggaepoo said:
Rusty,
You are so lucky that I experienced this problem and solved it on my own. You did not specify what ROM you were loading, but here is the fix:
First you need to get another pocketpc, hx2000 series like yours that is working.
Put that device into white screen bootloader or pre-BL mode (depending on which device you got to borrow)
Ensure that the battery on that device is 100% charged.
Run the original ROM upgrade for the ROM you wish to install (use PDAViet if it's WM6 and use the HP SP32408 to Run it)
Hit all the Ok screens until it brings you to the one that has the "UPDATE" button.
Remove the working Ipaq from the cradle and place it's 100% battery in you own.
Put your Ipaq into pre-BL mode and put it on the cradle. Press the calendar button to activate the usb drivers.
Once it says "USB", Hit the "UPDATE" button and it will load the proper ROM to your IPaq.
When It is done, perform a hard reset by formatting the PS on the device.
Voila!! Your Ipaq is Un-Bricked!! Put in your original battery and charge it up!
Enjoy!!
Bless...
Click to expand...
Click to collapse
You, my good sir, are a genius - worked great! Fixed BOTH 2110s
tangwd898 said:
hi Rustmonkey,
i have the similar things - i made my hx2110 brick when i flashed it with a different language ROM, it went 100% when i flashed the ROM but didn't work at all after that.
the problem is i can get it in the bootloader mode after trying many ways, at the same time the pc can't find any USB device at all.
how to make it work again?
thanks.
Click to expand...
Click to collapse
You're going to need another hx2000 series to make sure the battery is fully charged - put the battery in and then use the bootloader keystrokes immediately (contacts+itask+reset) - you made need to tap reset a few times while holding the other two to get it to work. After it is in bootloader mode, push the calander button while it is connected to the cradle/usb to get the pc to recognize it
Rustmonkey said:
You're going to need another hx2000 series to make sure the battery is fully charged - put the battery in and then use the bootloader keystrokes immediately (contacts+itask+reset) - you made need to tap reset a few times while holding the other two to get it to work. After it is in bootloader mode, push the calander button while it is connected to the cradle/usb to get the pc to recognize it
Click to expand...
Click to collapse
really amazing !!!!!!
I just saved my hx2110 as per your step by step instruction now.
Thank you very much.
ok, well, I thought they were fixed... now one of them freezes at the bootup screen, even when I do a clean reset... I've tried reflashing multiple times to no avail... any ideas whats going on?
ok, got everything working - reflashed the non-working one back to an original 2003 rom - which made if freeze at boot - then upgraded it via pre-bl to 1.00.00.L - from here, it wouldn't do anything after filling the bar at the boot screen, but it didn't CRASH (as in lights out) - so I ran the pre-bl again and ran the flash program for 1.00.00.L again WITHOUT swapping between the 2495 and the 2110 - just put the 2110 in pre-bl and away we went - flashed, formatted, and booted - then proceed to upgrade to WM6 via 1.00.00.H --> 1.02.00.H --> WM6 - works GREAT!!!
Thanks for the help everyone!
Dear All,
I`ve got the same problem but i don`t have a second ipaq.. is there anyway to repair it with out the second device???
Thank you very much
Abs
Hello,
I have run into some problems with a bricked hx2110.
I was flashing the IPAQ to a new ROM WM5 (Battery was full and I read all the instructions 10 times prior to flashing). While flashing, the progress bar went to 100% then faded out immediately and it wouldn't reset (clean reset). I put the battery in my friends hx3000 series and the battery I used was completely dead. It did flash to 100% though, but not matter how many times I try 1 + 3 + reset, it doesn't reboot. If I can figure out how to get it to boot, that would be great, but I can't get anything to come up with any key combinations.
To this point all I can do is get into Pre-BL mode 1.00.04. I have tried the below scenarios on two machines, both running windows XP SP2 (USB 2.0) with the firewall and virus software disabled.
http://forum.xda-developers.com/showthread.php?t=330382&page=4
1) I have tried the above links directions and used the the Universal Bootloader (Bootloader.exe). It gets to the point where it says "The PDA should be updating now" or something similar but nothing happens. I don't get any errors regarding communications (it sees the device when I hold the "Calendar" button until it says USB; windows then recognizes the device as "HP USB ..." so I know it's communicating).
2) I tried to use the Bootloader_GUI.exe beta so that I can watch the progress indicator but it just sits at 0%. There are no error messages so it is communicating but for some reason, the device won't let it flash (and the flash utility thinks it's doing something).
3) I tried the original ROM flash from HP (SP29856.EXE) and it recognizes the device, but because the current ROM on the PDA is hosed, when it does it's "verifying" process, it comes up with "?" marks as the model number and when it goes to flash it starts at .1% then says "FINISHED" immediately. The ROM utility thinks it flashed it correctly but it didn't flash anything. I'm guessing that the verification of the PDA failed and forced the utility to not flash.
Does anyone have ANY ideas of what to try? I wish I had another HX2000 series PDA and try the "swap" thing prior to hitting the update button but I don't. All I have to work off of it my sad bricked PDA and a full battery (friend keeps charging it). His PDA is an HX3000 series.
Any ideas would be appreciated,
Thanks!
Are you using a the HP flash program that is specified for your device?
2nd - you might be able to use your buddies device in a swap as well - not sure but its worth a shot - use HPs upgrade program, let it verify, then swap your device onto the same cable - overwrite the firmware in the update program for HIS device with firmware compatible with yours and then hit update - let us know if this works...
I am using the "official" HP flash program specific for the HX2110 (from their website - SP29856), bootloader.exe, and bootloader_gui.exe
I wanted to try my friends, but he won't let me touch his because I bricked mine lol (I swore nothing would happen to his but he still won't let me try it).
Anyway, I just copied over the ROM image (from HP) and stripped out the header (now showing 64 bytes before the ECEC). The ROM is for WM2003. I copied the ROM in binary using psdwrite.exe to an 256 MB SD card. As soon as I can get the battery back, I'm going to try to flash it from the SD card. If this fails, I am going to try to play around with MTTY / USB and manually call the ROM flash and see what happens.
Having another HX2000 series would make this easy (maybe a little TO easy )!
Bootloader never worked for me - but if you can get it to manually call the flash, more power to you good luck!
Well it was worth a shot. After spending the better part of the day with the PDA, I have made no more progress (can't get Pre-Bl to update). The only option I have now is to find someone with another hx2000 series that is willing to resurrect it from the dead for me (PM me if you can help - I will pay two way fare). Until that happens, it's going in the "broken" drawer with all my old comp stuff .
Thanks to all the tips and tricks that is posted on these forums and brighthand! There is a wealth of information on this topic and without them, I would have gotten nowhere in trying to repair the device (granted, I wouldn't have been intrigued to upgrade the ROM in the first place and would still have a working PDA, but that's besides the point ).
Best of luck to you all.
1).download original ROM from HP (sp29799) -extract files
2) download http://upload.dvhk.pl/content.php?id=88892 - replace files
3) flesh device.
bay!
link crash http://upload.dvhk.pl/content.php?id=88892 - replace files
Please it can raise it again, thanks
Absolut3k said:
Dear All,
I`ve got the same problem but i don`t have a second ipaq.. is there anyway to repair it with out the second device???
Thank you very much
Abs
Click to expand...
Click to collapse
Same here.. is there another way to un-brick hx2110 on this problem ? thx ...
Solved, my hx2100 returns to be in this world
thank you i saved my ipaq
I'm the newbiest of them all, I think I bricked my brand new Excalibur!!!
Sorry if I'm posting in the wrong place, but I need heeeelp!
O.K., here it is:
I just downloaded kavana's 080314 WM6.1 installer for the HTC Excalibur, I ran the exe and followed instructions, afterwards, the ROM app opened and started upgrading the phone but it got stuck at 1%, it made be go thru the recovery process several times (unplug, turn off, disconnect battery, turn on) but it always started on tricolor mode and always got stuck on 1%, after a third recovery process the ROM app just quit and left me hanging on tricolor mode!!!
Activesync won't connect now, I try to run kavana's exe again but it doesn't recognize the phone either, the phone is on, conected (windows makes the usb sound for connection) but it is not recongized, it's as if it's not plugged.
It is stuck on tricolor mode and I don't know what to do!
Please help me!!!
Try the dicussion thread "Bricked my T Mobile phone" there are plenty of answers there.
Will this work?
I saw this on said thread, but I presume it applies for a Herald phone, will it work?
The tricolor mode is "bootloader mode"?
Isn't there some sort of restart that can fix it?
Can someone elaborate on this? I'm really a super-noob!!!
"Try a SD card flash to unbrick your device
This is how:
MAKE SURE THE HERALD IS FULLY CHARGED BEFORE STARTING THE PROCES
#01 Download your original RUU
#02 Download (if not yet installed) WinRar and install
#03 Copy your full sd micro card to your harddisk and format your card with FAT 32
#04 Rightclick the downloaded exe file with your original RUU, click Unpack here
#05 In the map the will be created you will find a file (or similar) called RUU_signed.nbh. Copy this file to your formated sd microcard.
#06 Rename the file to Heraimg.nbh
#07 Get your Herald into bootloader modus by pressing the comm manager button and the camera button and pressing the reset button at the same time. Do not release both buttons until your in bootloader.
#08 Once in bootloader pop in your sd micro card.
#09 As soon as your card is popped in the screen will say something like "Reading SD card". Wait it out till it says "Push button to start" and slide the indicated volume slider down.
#10 The Herald will start the flashing proces. Wait it out till it says "Press any button" and hit the send button.
#11 Perform a hard reset
#12 Voila! Your back in business"
velascoperroni said:
I'm the newbiest of them all, I think I bricked my brand new Excalibur!!!
Sorry if I'm posting in the wrong place, but I need heeeelp!
O.K., here it is:
I just downloaded kavana's 080314 WM6.1 installer for the HTC Excalibur, I ran the exe and followed instructions, afterwards, the ROM app opened and started upgrading the phone but it got stuck at 1%, it made be go thru the recovery process several times (unplug, turn off, disconnect battery, turn on) but it always started on tricolor mode and always got stuck on 1%, after a third recovery process the ROM app just quit and left me hanging on tricolor mode!!!
Activesync won't connect now, I try to run kavana's exe again but it doesn't recognize the phone either, the phone is on, conected (windows makes the usb sound for connection) but it is not recongized, it's as if it's not plugged.
It is stuck on tricolor mode and I don't know what to do!
Please help me!!!
Click to expand...
Click to collapse
I believe you didn't application unlock it first. I had same issues. I finally got it to load. I don't think you bricked it. Remove battery wait a few seconds and restart phone
timothyjok said:
I believe you didn't application unlock it first. I had same issues. I finally got it to load. I don't think you bricked it. Remove battery wait a few seconds and restart phone
Click to expand...
Click to collapse
Already did that... still on "brick" mode...
Question: is my warranty still valid? I bought it 3 days ago.
you can solve simply to launch original upgrade to wm6 rom
glenbo said:
Try the dicussion thread "Bricked my T Mobile phone" there are plenty of answers there.
Click to expand...
Click to collapse
Do try these procedures first. I'm just throwing it out there but if you try again it is probably a better choice to flash to WM6 first. Then try flashing to the 6.1.
I'm sure you can return it but come up with a believable excuse.
Yes, You Are Correct!
pfunkside said:
Do try these procedures first. I'm just throwing it out there but if you try again it is probably a better choice to flash to WM6 first. Then try flashing to the 6.1.
I'm sure you can return it but come up with a believable excuse.
Click to expand...
Click to collapse
Yes, that is the correct path for him to take, install a 6.0 ROM first, before installing a 6.1 ROM. I suggest he install the T-Mo official wm6, just to get things started in the right direction again.
(1) If the device is still in the tri color mode (bootloader mode), that's a very good sign, it's not bricked. Connect the device to your PC via active sync in the tri color mode, you may think that the device is not connected to Your PC but it is, it may not look like it's connected, run the official T-Mo wm6 ROM RUU WWE, it will install on your device as long as your device is in the tri color mode.
(2)Once you get the wm6 ROM installed on your device, you must first SDA_ApplicationUnlock your device, next you want to Certificate AppUnlock and SurrealApplication Unlock your phone. Now, the reason you are doing all these unlocks are because you coming off the T-Mo wm6 ROM.
(3)After all this have been done, it now ok to try to install the 6.1 ROM on your device.......!
Great support!!! But now comes the obvious question from the n00b of the n00bs!!!
Got it, now the big question is: how to flash to WM6?
Is it done by the steps I posted early? (formatting SD, etc.)
Also, where do I get the T-mobile RUU?
Finally, there are a few things you should know, my phone was bought in Mexico, under the cellphone company Movistar (Spain's Telefonica and I've heard U.S. AT&T), it had WM5 before I "bricked" it (hehehe).
When I turn it now, a few miliseconds before the tricolor screen I can read in the phone a "waiting for SD card" message when the tricolor screen comes on, I get this version of RUU 1.15.000.
I appreciate all your help, as a contribution to this amazing community, when I get thru this, I hereby commit myself to write a fully understandable guide for noobs with the same problem (not too long).
T-Mo Wm6
velascoperroni said:
Got it, now the big question is: how to flash to WM6?
Is it done by the steps I posted early? (formatting SD, etc.)
Also, where do I get the T-mobile RUU?
Finally, there are a few things you should know, my phone was bought in Mexico, under the cellphone company Movistar (Spain's Telefonica and I've heard U.S. AT&T), it had WM5 before I "bricked" it (hehehe).
When I turn it now, a few miliseconds before the tricolor screen I can read in the phone a "waiting for SD card" message when the tricolor screen comes on, I get this version of RUU 1.15.000.
I appreciate all your help, as a contribution to this amazing community, when I get thru this, I hereby commit myself to write a fully understandable guide for noobs with the same problem (not too long).
Click to expand...
Click to collapse
Is your mobile device still in the tri color mode, if so just connect it back to your PC via active sync, It will accept the download! OK you can get the T-Mo wm6 at T-Mo's website, if not I will send you a link with the T-Mo wm6 RUU. Don't panic, you are still in the game.......!
Update!! Phone unbricked but still on WM5!
Ok... I used this ROM: HTC_S620_WWE_1.27.405.1_4.1.13.44_02.94.90_Ship.exe
It went thru the upgrading process but got stuck at 3%, anyway, it finished with a message like "this ROM cannot be used for your phone" or something and restored WM5.
Now I will follow instructions on the thread: "The Full Guide To Upgrading From Windows Mobile 5 to 6" and I'll be posting my acomplishments on this thread.
Question: The reasons for me not being still able to upgrade may be:
1. I haven't unlocked phone,
2. My phone is for Mexico and cellphone co. "Movistar", or
3. I'm running Windows XP as a virtual machine (via parallels) on an intel Macintosh and somehow there's a problem with the USB drivers.
I'm rooting for option 1 (but kavana's upgrade was supposed to already unlocked it). Option 3 maybe but then, why do I get Activesync to run? Option 2 would be a bummer!
T-Mobile WM6 RUU WWE ROM
Get the T-Mobile official Wm6 RUU WWE Rom here http://www.mediafire.com/?0vtw32zmuz3 ......!Oh! I throught you had a Excalibur.....!
Just can't seem to upgrade WM5 to WM6!
Iv'e tried the T-Mobile ROM and the HTC ROM and I get an: "invalid vendor id"
I tried every step on the aforementioned thread, even de CIS unlock, and still no luck... again, my vendor is movistar/telefonica/cingular.
Any thoughts?
Your Answer Is In jockyw2001 Thread
velascoperroni said:
Iv'e tried the T-Mobile ROM and the HTC ROM and I get an: "invalid vendor id"
I tried every step on the aforementioned thread, even de CIS unlock, and still no luck... again, my vendor is movistar/telefonica/cingular.
Any thoughts?
Click to expand...
Click to collapse
A easy frix, but read the instructions very carefully, jockyw2001 thread is located in the sticky section. What you are looking for will be in post #1.........!
New Instructions
Run the Excalibur Uspl-CID ByPass.zip, extraxt on your PC and open it there, you will see several file folders. Open the one that say (uspl) MS-Dos batch File, follow on screen instructions by pressing any key. This time when you see the white screen on your device do not panic! Run the HTC WM 6 ROM, this is done while the screen is still white on your device. Just follow the on screen instructions on your PC.............!
Now I definitively bricked it!
I ran the CID unbloker, screen went blank, ran the ROM, it got to 16% and made me do a recovery, after the recovery it gave me the same "invalid vendor id" message and it automatically restarted the phone, but...
The restart stopped at the HTC intro screen!! I've restarted it several times and it just stops on the first HTC logo screen... even a hard reset won't fix it!!!
HEEEEEEEEEEEEEEEEEELP!!!
Here is a visual aid.
You are not reading into detail. Use the Tmobile rom instead of the HTC Rom.
http://forum.xda-developers.com/showthread.php?t=368998&highlight=Jamerican
Still Bricked!!!
Yeah!!! superb visual aid!!!
I just wish I had seen it before I bricked it!!!!
This is the current state of my phone: I press power, I see a white screen with the HTC logo in the middle, the phone vibrates, still the same HTC logo... and it is stuck that way! I can't turn it off, I have to take out the battery!!
I've tried a hard reset, same thing happens! It stays stuck on the HTC logo screen and I'm forced to pull the battery out for the phone to shut down.
It is obviously not recognized in any way when I plug it to the PC's USB.
What made this happen? HTC Generic ROM got stuck on 16% before telling me "invalid vendor id", restarted the phone and voila: brick!!
Boy, I wish I was back in the tricolor mode!!!
IS THERE NOTHING I CAN DO?
I'm seriously thinking about going back to the vendor on monday and saying: It was like this when I woke up (I just bought it three days ago!!!)
If it gets that far, it doesnt seem totally bricked, ima PC man, so this may be off, but it seems like some kinda bootloader error on the phone itself....IE, the HTC screen is all that the bootloader tells the phone to load. Have you tried forcing the phone into bootloader mode?
I Looooooove Google!!!
OK... I found a turnaround for the problem... got it to go to bootloader mode!!!
Whenever something like these happens to you this is the hard way to put your excalibur/dash in bootloader mode:
1. Take out battery and sd card;
2. Plug your USB cable to your PC (not yet to the phone)
3. Press and keep holding the SIMB. key (the one with the camera next to the space bar)
4. Plug your USB cable to your phone (while still pressing the SIMB. key)
5. Voila: You are in bootloader mode!!
This was gotten for a 15 min. search in google!!
Now... I'll keep going with my WM5 to WM6 upgrade...
Alright I'm finally going to throw a post up, go ahead and get all your "use search" "it's on search" "it was in a thread" out of the way now, cause I've gone through 76 thread pages of reading and searches and I can't find an answer that works.
I am continually getting the ERROR 262 in RUU everytime I attempt to use it to flash.
- I am running Vista 64bit (not sure if that is the problem or not)
- Using WMDC 6.1
- I have uninstalled and reinstalled WMDC 6.1 a total of 7 times
- I have used every single USB port on my computer.
- I have restarted a total of 15 times, both the computer and hard resets of the phone.
- I have tried both the Unlocker (I'm not sure if I have to unlock a second time or not after my WM 6.1 update) and just the ROM Update.
- I have tried doing the forced bootloader mode (Power+Camera+Reset) and simply allowing the program to do it on it's own.
Everytime it drops into Bootloader (3 color) mode, it drops Activesync and then obviously errors out because of lost connection. I've tried simply running the program and never unplugging the USB cable, I've also tried unplugging the USB cable when the DOSprompt part of the batch tells me to. Everything I've read says to do this, but I don't remember doing this for the 6.1 WM Update. It also doesn't make sense.... if you unplug the device, it's going to drop activesync everytime....
I've just updated every program, reinstalled everything more then 5 times, done countless resets, tried every USB plug and nothing is working. Hopefully this is something easy I'm just overlooking -- or something easy like "It doesn't work with Vista 64" so I can at least get an answer.
Again, I apologize if this was answered somewhere previously. I genuinely tried for 3 hours using search, on and off XDA, so that I wouldn't have to post a question thread but never found a "fix" that worked.
Thanks in advance.
Traumatique said:
Alright I'm finally going to throw a post up, go ahead and get all your "use search" "it's on search" "it was in a thread" out of the way now, cause I've gone through 76 thread pages of reading and searches and I can't find an answer that works.
I am continually getting the ERROR 262 in RUU everytime I attempt to use it to flash.
- I am running Vista 64bit (not sure if that is the problem or not)
- Using WMDC 6.1
- I have uninstalled and reinstalled WMDC 6.1 a total of 7 times
- I have used every single USB port on my computer.
- I have restarted a total of 15 times, both the computer and hard resets of the phone.
- I have tried both the Unlocker (I'm not sure if I have to unlock a second time or not after my WM 6.1 update) and just the ROM Update.
- I have tried doing the forced bootloader mode (Power+Camera+Reset) and simply allowing the program to do it on it's own.
Everytime it drops into Bootloader (3 color) mode, it drops Activesync and then obviously errors out because of lost connection. I've tried simply running the program and never unplugging the USB cable, I've also tried unplugging the USB cable when the DOSprompt part of the batch tells me to. Everything I've read says to do this, but I don't remember doing this for the 6.1 WM Update. It also doesn't make sense.... if you unplug the device, it's going to drop activesync everytime....
I've just updated every program, reinstalled everything more then 5 times, done countless resets, tried every USB plug and nothing is working. Hopefully this is something easy I'm just overlooking -- or something easy like "It doesn't work with Vista 64" so I can at least get an answer.
Again, I apologize if this was answered somewhere previously. I genuinely tried for 3 hours using search, on and off XDA, so that I wouldn't have to post a question thread but never found a "fix" that worked.
Thanks in advance.
Click to expand...
Click to collapse
Try another computer. It does work with Vista 64 (I've done it many times), but there's no point in beating your head against the wall for this. There are so many things that it could be you might as well try another computer so that you at least now it is the computer and not your Vogue.
-GT
You phone is not unlocked and you are trying to flash a custom ROM.
Try following the instructions in this thread found about halfway down the first page of the forum.
http://forum.xda-developers.com/showthread.php?t=508544
atoz350 said:
You phone is not unlocked and you are trying to flash a custom ROM.
Try following the instructions in this thread found about halfway down the first page of the forum.
http://forum.xda-developers.com/showthread.php?t=508544
Click to expand...
Click to collapse
Be it locked or unlocked is beside the point. As I stated before, I unlocked it once for the WM 6.1 upgrade and being as I wasn't sure if I had to do it again, I attempted to do it again.
Regardless of if it's trying to flash the ROM, or use the Unlocker, the same thing always happens. Windows Mobile Device Center (ActiveSync) drops connection once the phone goes to the Bootloader (3 color screen), and it errors out 262 (Connection Lost).
I have attempted to give as much information as possible so I can get input on if I'm missing a step or if it's simple bugging out. I will try what gt! suggested and attempt this on a different computer. However, from the information I've given can anyone confirm that I'm at least doing the correct steps -- there's just some gremlin popping up keeping me from completing it?
Thanks again.
Flash via SD card. There are instructions in CodyBear's FAQ thread.
From experience...use a blank or backed up card.
Traumatique said:
Be it locked or unlocked is beside the point. As I stated before, I unlocked it once for the WM 6.1 upgrade and being as I wasn't sure if I had to do it again, I attempted to do it again.
Regardless of if it's trying to flash the ROM, or use the Unlocker, the same thing always happens. Windows Mobile Device Center (ActiveSync) drops connection once the phone goes to the Bootloader (3 color screen), and it errors out 262 (Connection Lost).
I have attempted to give as much information as possible so I can get input on if I'm missing a step or if it's simple bugging out. I will try what gt! suggested and attempt this on a different computer. However, from the information I've given can anyone confirm that I'm at least doing the correct steps -- there's just some gremlin popping up keeping me from completing it?
Thanks again.
Click to expand...
Click to collapse
CONNECTION DROPS BUT............ it should be installing new drivers.
When i flash my phone on windows 7 it loses connection when it enter bootloader just like you.
And by the time the drivers for the qualcomm chip on my htc touch vogue gets installed (this is the recognized driver when your phone is in bootloader)
the RUU rom updater/installer times out.
After it times out for me i make sure that the driver for the qualcomm chip (the driver that is seen by windows when your phone is in bootloader) is installed, i run the updater again.
Now it should run through smoothly again.
Alternate method:
Flash by ur sd card.
or
Try a different computer.
start it up on serial mode then plug it in to USB, go to device manager make it search for new devices. Driver should start loading and start RRU, if all else fails use the SD CARD for The Flash
Alright, well now I guess a second question looms. I was going to take everyones advice and attempt to flash with the MicroSD Card, but now I'm having problems with that one as well.
Yes it has to be 2GB or less and formatted FAT32
I always find my original 512MB works perfect for flashing from
as to how to get it to your card...
Extract the ROM you want to use
Find the largest *.NBH file and copy it to your desktop
at the desktop rename it to VOGUIMG.NBH (I believe the caps in naming is important)
Copy that file to the root of your formatted FAT32 2GB or less SD Card
enter bootloader mode and it should go from there.
Click to expand...
Click to collapse
Those are the directions on the FAQ. I have the original 512mb card, formated to FAT32. I went into the Unlocker RAR, found the Voguimg2.nbh, renamed it to VOGUIMG.NBH as instructed in the FAQ. Placed the file on the freshly formatted MicroSD Card, put it in the phone and went to bootloader mode and... nothing.
I attempted putting the card in, then going to Bootloader. I tried going to bootloader, then putting in the card. I tried putting it from USB to Serial and vica versa. Tried hitting all the buttons. Nothing happens, it just hangs out on the 3 Color Screen.
Am I missing something, or am I just cursed to not flash my phone more then once? Heh. Thanks again for all the help.
[EDIT] For clarification, since I don't know if I have to unlock before every flash or not, I'm just attempting to unlock it again and hense only using the Unlocker ROM. It was previously flashed for the 6.1 update, but I figured it couldn't hurt to try the unlocker again so that's been the ROM I've been trying to run currently.
Traumatique said:
Alright, well now I guess a second question looms. I was going to take everyones advice and attempt to flash with the MicroSD Card, but now I'm having problems with that one as well.
Those are the directions on the FAQ. I have the original 512mb card, formated to FAT32. I went into the Unlocker RAR, found the Voguimg2.nbh, renamed it to VOGUIMG.NBH as instructed in the FAQ. Placed the file on the freshly formatted MicroSD Card, put it in the phone and went to bootloader mode and... nothing.
I attempted putting the card in, then going to Bootloader. I tried going to bootloader, then putting in the card. I tried putting it from USB to Serial and vica versa. Tried hitting all the buttons. Nothing happens, it just hangs out on the 3 Color Screen.
Am I missing something, or am I just cursed to not flash my phone more then once? Heh. Thanks again for all the help.
[EDIT] For clarification, since I don't know if I have to unlock before every flash or not, I'm just attempting to unlock it again and hense only using the Unlocker ROM. It was previously flashed for the 6.1 update, but I figured it couldn't hurt to try the unlocker again so that's been the ROM I've been trying to run currently.
Click to expand...
Click to collapse
As explained in Cody's FAQ, once your phone is unlocked to flash, it stays unlocked. The only thing you MIGHT want to do other than just flash the new ROM is to flash a stock ROM, then the new ROM.
Go ahead and try putting the VOGUIMG.NBH from the ROM on the card and see what happens. From what I remember, you should have the card in the phone then put it into boot mode. I believe that was what I did for my first flash ever.
What method did you follow when you flashed to 6.1? Has anything changed about what you are doing now?
Also it might be important to know that when flashing via USB on a 64-bit machine the RUU program will give you an error about not working on a 64-bit computer. Just ignore the error and click ok, it will pop up a few times just keep hitting ok and it will work. That error pops up even though it's false.
when i first tried flashing a custom rom, i extracted the downloaded file and when i clicked on the ruu i had the same error... i then tried just running the downloaded file without extraction and it worked fine.
same thing happend 2 me Just run the RUU do not extract files!!!!!!!((-;
Barogi44, JFive1182 -- You are both princes among men.
The Unlocker will only run on the first auto-extract of the file. You cannot run the batch from the extraction folder afterwards, eventhough all it does is auto-extract the contents and then auto-run the batch file.
Out of curiosity... and being infuriated I went and tested this again just to see. On 3 other computers the same thing happened. I have no clue why it would bug out that way... or if it was written that way that's a pretty bad design.
In any case, someone should put that in the FAQ. You have to let it start the process from the auto-decompressing RAR, you can't start it again after the fact by running the batch file from the extracted folder. If it said this anywhere, the 3 guides I read never mentioned that (nore the unlocker's thread at ppcgeeks) so I didn't catch it.
Thanks again for everyone's input, and obviously JFive1182 & Barogi44 for actually letting me know how to make it work!
your welcome
Traumatique said:
[..]The Unlocker will only run on the first auto-extract of the file.
[...]someone should put that in the FAQ. You have to let it start the process from the auto-decompressing RAR, you can't start it again after the fact by running the batch file from the extracted folder. If it said this anywhere, the 3 guides I read never mentioned that (nore the unlocker's thread at ppcgeeks) so I didn't catch it.[..]
Click to expand...
Click to collapse
Bump for emphasis. I had the same problem.
Tutorial said this: "Use WinRAR and extract both the files into separate folders,"
ONLY extract the NFSFAN rar.
Hi all!!
Ever since I got my Sprint Vogue, I have spent God only knows how many hours looking for and gathering information regarding this phone (flashing instructions, unlocking, SuperCID, etc). There are a few sites that have fairly comprehensive guides as to how to do this, but there are very few posts in the Vogue Section here at XDA-Developers.
Having said that, I figured I would create my own "How to Flash Your Vogue"-Thread. This is a multi-step process and I cannot emphasize the importance of following every step down to the "T", that is unless you are looking for a silicone-skinned brick...
Who is this guide for?
*Anyone with a CDMA version of the Touch. [highlight]That means no GSM[/highlight]
*Noobs and Seniors alike.
*People who have trouble flashing their devices.
*Anyone looking for links to more information.
*Curious people in general.
*Anyone willing to get rid of the nasty stock rom and looking for a newer and cleaner OS (notice that I never said more stable, so do not blame me afterwards ).
[highlight]Please keep in mind that there is always a chance of bricking your device with these procedures. I will not be in any way, shape, or form responsible if you damage your device while doing this.[/highlight]
Got your coffee? Alright, let's do this.
Step 1. Preparing the device
As with every phone, you have to make sure that you have the following things done before flashing:
* Battery charged at least 50%.
* All the necessary programs (see next post).
* Instructions handy.
Make sure that you back up all your information (contacts, e-mails, files).... essentially, anything that you would like to keep post-flashing. You can do this via Active Sync/Mobile Device Center or via third party software (PIM Backup is really good)...
You will have to reinstall every last piece of software in your device as it will be hard reset. Some programs may work if installed in a SD card directly, but a lot of them write things to the registry and copy files to the device, which they require to run. Long story short, keep all your cabs and exe files in a safe place so you can restore later if needed.
Step 2. Unlocking the Device (HardSPL)
Unlocking the device is done so that you can flash custom roms in your devices. The unlocker that you are about to download and use was provided by "ImCoKeMaN" at PPCGeeks. If you are interested in the full thread, please click here.
If you have read the above link, you will see two versions of the HardSPL (0.40 and 2.31). Simply use 2.31 as it works fine with most devices.
[highlight]To use this under Windows XP,[/highlight]
1. Connect your device to your computer and make sure it is synced with ActiveSync.
2. Download and extract the contents of the zip file, which is an exe. Let it run to completion. You will be prompted to disconnect and reconnect your device at one point in the process. Do it... don't worry
3. It will look like it is flashing a rom via a RUU. Do not disconnect the device after it is done!!!!!
4. Once it is done flashing, you will see a prompt that says that it will run exitbl. DO NOT DISCONNECT YOUR DEVICE. At this point, open ActiveSync, go to File>Connection Settings> Uncheck "Allow USB Connections". Continue following the on screen instructions and let it finish.
5. Go to bootloader once more to verify that it worked. You should see 2.31 CoKe MFG.
[highlight]To use this under Windows Vista/7 x64 (thanks jitajt),[/highlight]
jitajt said:
connect your device to WMDC (it's not necessary to set up device, just connect without setting up device)
then right click on the 2.31 unlocker and run as administrator
follow the directions, you will get an error about sleep.exe not being compatible with x64 but just hit ok and continue, (you will get about 10 of them)
then just keep following the directions in the command prompt and it will put your phone into bootloader then you have to disconnect and reconnect when it tells you to. and it will flash your phone and reset it. then your done you can close the command prompt and disconnect your phone.
I did it just like above and I have not had any problems.
Do this at your own risk as I am not responsible for your phone
Click to expand...
Click to collapse
Step 3. Flashing your Roms
The time has finally arrived. You sat down patiently through the unlocker and you are now ready to take the leap of faith into what you believe will bring your device to a new level of usefulness (also known as getting rid of that nasty, bloated, stock rom )
The process is relatively simple:
1. Download the RUU package from this post. I am only posting this because some cooks only post the rom nbh files rather than the whole package.
2. Go into the threads and look for whichever rom you prefer. Look at my signature to learn which one I am using. NFSFan (my current one) is by far the best one I have tried so far. You can download it from here
3. Put your device in bootloader mode and connect the device to the computer. [highlight]Once in bootloader, activesync will NOT see the device. If the RUU gives a connection error, try to run it with the devices in regular mode (with ActiveSync connected)[/highlight]
4. Open the Romupdateutility.exe and follow the steps.
5. Once it is done flashing the rom, disconnect it from the computer and hard reset it. To do this, simply hold "Send" + "End Call" +Stylus in the reset hole for about 3 seconds. It will prompt you to erase all the data and restore to factory defaults. Press "Enter", which is the center button in the directional pad. Once it is done, press "Send" to reboot.
Congratulations, you just flashed your first rom for Vogue
Step 4. SuperCID
This step can be skipped if you are not thinking of doing anything as far as your radio (such as flashing radios other than the ones intended for Vogue). This is also used to do other things such as modifying certain important things on your device such as the NV files, which is information that will not be discussed here. However, if you are interested in finding out more, simply google it, there is a ton of information out there.
Anyways, back to SuperCID... here is the procedure (thanks to hpnasik at mobile-files.com for the post)
1. Download the following special rom . This is an Alltel rom with radio 3.37. This was specially prepared to be able to reduce the Security Level of the device to level zero.
2. Download mtty since you will need it. Do not worry if you do not how to use it. You will have a step by step in this guide.
3. Flash the Alltel rom from above.
Now comes the fun part...
4. Disable USB in Connection Settings of Active Sync
5. Boot The Phone holding power button and camera button to enter bootloader.
6. Phone Will Display Serial in Bottom
7. Connect Phone to PC
8. Phone should Display USB instead of Serial in Bottom
9. start mtty.exe
10. Select All Default and Connect to USB in drop down box and Shoot the Following Commands (All Commands are case Sensitive)
11. run command rtask a : After this Command Phone will not Display any thing
12. run command echo_on : even though nothing is shown to screen
13. run command readCID : in Sprint it will display SPCS_001
14. run command writeCID 00000000 : Set CID Value to 00000000 replaces SPCS_001 in Sprint (This make PPC Radio Security Level to Zero)
15. run command readCID : This will Display the Update CID as 00000000
16. run Command retuoR : This will return to Original Boot Loader State
Congratulations, you just SuperCIDed your device. Original thread with the instructions can be found here if you are interested.
Step 5. Flashing your radio.
Now that your device has been SuperCIDed, you will have the opportunity to flash radios that have been ported to this device (ie. there is a version of the 3.42.40 radio for the Titan, which has been ported to the Vogue). There are two ways of doing this:
Way 1: Do it by flashing via RUU (same as with flashing a rom)
Way 2: Flash via microSD card. Simply put whichever radio that you wish to flash in the root of a 2GB or less microSD card formatted to fat32. Rename the radio to VOGUIMG.NBH and put your device in bootloader. The flashing will start by itself.
Way 3 (I know I said two ways...): There are a few stock roms that come with new radios. One of them can be downloaded directly from HTC and it is for the Sprint Touch. This one comes with Radio 3.42.30
The other one is for Bell Mobility and this one comes with Radio 3.42.50.
Why am I giving "Way 3" if the other two options seem much easier?? I have run into the problem where my device would not let me flash other radios than the one that I had. SD card method did not work and the RUU started out fine but quits at 8% rebooting my phone and displaying Error 328 in the RUU on the PC. Anyway, here are the links...
Sprint rom with radio 3.42.30
Bell rom with radio 3.42.50
Verizon Stock Rom
All Shipped Roms (All Carriers) - Thanks conflipper!
All Above Radios zipped
The newer radios perform a little better and give out better GPS signal (faster locks)....
Hang on a sec... did you just say GPS?!?!? But my Vogue does not have a GPS.... It does, just read a little further and be happy
Step 6. Enabling GPS, Returning to Stock, and Carrier Cabs
As I said before, there is a GPS hidden on your device. Now, if you are like me and went straight to the specs of the phone to confirm, you will probably try to call BS on this. Long story short, there are a few custom roms which have this "tweak" already implemented (like the one I am using from NFSFan). If you require some more info, I will post it later...
[highlight]Location must be on or else your GPS will not work. To activate it, go to Settings>Personal>Phone and change the Location setting to ON instead of 911 (thanks for pointing it out, th3lolz)[/highlight]
[highlight]For Verizon Users[/highlight]
br125 said:
For those of you with the official mr1 update from verizon that cannot get their gps working:
My xv6900 came with the official update and I got it working, it involves downgrading to a NON-GPS radio, then back to a gps radio...
go here: http://forum.xda-developers.com/showthread.php?t=533639
now the instructions are going to imply that you must load the unlocker before each flash... bs don't worry about that
1. flash the .40 unlocker
2. flash the non-gps rom (reset before customization)
3. flash the 2.31 unlocker
4. flash the vzw rom (reset before customization)
5. flash any custom rom or android rom
that's it, time consuming, but it works
*ignore the multiple flashing instructions, its completely unnecessary, I've never flashed more than once with no problem ever....
I also suggest keeping the vzw radio, but do as you will, I like the 3.37.38 radio.. ain't broke don't fix it
lastly, just make sure you RESET BEFORE THE CUSTOMIZATIONS RUN...... that is what locks your gps.
good luck!
ps. the verizon radio rom that is in that post is for the "leaked" 3.37.37 radio, I reccomend using the official update from verizon here for the 3.37.38 radio rom instead:
http://www.pcdphones.com/phone_downloads.aspx?bid=95&cid=1&mid=302&carrier=Verizon Wireless
RESET BEFORE CUSTOMIZATIONS
Click to expand...
Click to collapse
[highlight]How to Relock you phone[/highlight]
If, for whatever reason you need to return your phone for repair/replacement, you will need to relock it. To relock your phone, simply run the unlocker 0.40 and flash the stock rom of your carrier.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker.exe
[highlight]Carrier Cabs[/highlight]
Thanks to Codybear for gathering all of the cabs with settings for various carriers. But since the link went down, here is another one courtesy of LMiller1708
https://sites.google.com/site/vogueroms/vogue-files
This information was only gathered by me and I take no credit whatsoever other than trying to put it in a one stop thread. Thanks to the following people
Shadowmite
ImCoKeMaN
mindfrost
NFSFAN
Codybear
joshkoss
and a bunch of people that were involved in developing all this...
Thread sticky'd as requested
Peace,
Josh
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
dwigginstm said:
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
Click to expand...
Click to collapse
How exciting!! My first victi...erh patient
Did you put the device in bootloader mode? If you did and it is connected to the PC, you should see USB on the screen of your device. Also, do you have ActiveSync on your XP machine? You will need it for the drivers on this step. Changing USB ports sometimes help as well. And one last thing, do not use a USB hub, go directly through the USB ports in your computer. Good luck!
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
yes i have activesync set up with the phone and pc, but when i put the phone in bootloader mode and connect it the pc recognizes it but not activesync. is there another program i can unlock the phone with?
dwigginstm said:
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
Click to expand...
Click to collapse
Do not worry about ActiveSync. While you are in bootloader, the device is not running WM, which is why your computer only sees it as a USB device. This is perfectly fine. ActiveSync will not recognize it.
Please, follow the instructions in my post for unlocking. Read it thoroughly and try to understand it, else you will end up bricking your device.
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
dwigginstm said:
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
Click to expand...
Click to collapse
that is a message in the RUU. do not pay attention to it. good luck...
so i finally got the unlocker to start and it begins the ten minute process and stops then show a 262 error code ive done this over and over again
Let's go from the top. I just saw the message that you were talking about. The unlocker does ask for ActiveSync as you pointed out and it is asking you to connect the device to the computer. Then it asks for you to press any key when that is done. So, try that and you should see the word "initializing" with a dotted line getting longer for about 20 seconds. Do that.
The RUU will start up afterwards. The prompt will tell you that it is going to flash a new SPL, and if I am not mistaken that is where you are getting stuck.
Just out of curiosity, which version of the Vogue do you have? (Alltel, Bell, Verizon, Sprint, US Cellular)?
no internet
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
terrancextc said:
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
Click to expand...
Click to collapse
You downloaded a cab. Simply put it in your SD card and run it by tapping on it. Don't unzip it...
Unlocker is not 64 bit compatible... grrr....