Related
yea i can't believe it happened... my question is i have flashed a cooked ROM before and all and now i am running spb mobile shell with a custom theme from mobilecustoms.... i do have a warranty on my phone... do you think i can get away with replacing my phone?? i notice that my sleep/wake button does not work and the vibration feeling is very low... so do i need to flash to a the stock ROM? can i leave it the way it is and bring it to them? does insurance even cover water damage??? any help is MUCH APPRECIATED. thanks!
Take the battery out. Put the battery and the phone in a bag of rice for 2 days. After that the phone should work fine. My wife did this with her Blackberry and it worked fine after a couple days.
Typically insurance doesn't cover "water" damage as they can tell you did it. On the battery and on the inside of the phone there are 2 stickers than turn red when they get wet. So once you take it in and ask, they will crack open the phone. Never hurts to ask though.
drhuggybear said:
Take the battery out. Put the battery and the phone in a bag of rice for 2 days. After that the phone should work fine. My wife did this with her Blackberry and it worked fine after a couple days.
Typically insurance doesn't cover "water" damage as they can tell you did it. On the battery and on the inside of the phone there are 2 stickers than turn red when they get wet. So once you take it in and ask, they will crack open the phone. Never hurts to ask though.
Click to expand...
Click to collapse
really rice? lol. ahhh i dont have any rice at the moment lol. ive been meaning to buy some as well... anyways yea the stickers i noticed that.... but if i were to bring it in and they saw how my phone was modded but using spb mobile shell, does that void the warranty?
toawkanavngthded said:
yea i can't believe it happened... my question is i have flashed a cooked ROM before and all and now i am running spb mobile shell with a custom theme from mobilecustoms.... i do have a warranty on my phone... do you think i can get away with replacing my phone?? i notice that my sleep/wake button does not work and the vibration feeling is very low... so do i need to flash to a the stock ROM? can i leave it the way it is and bring it to them? does insurance even cover water damage??? any help is MUCH APPRECIATED. thanks!
Click to expand...
Click to collapse
Shame to hear about your Rhodium
Covering it with rice is a common practice to absorb the humidity
I don´t remember where but I´m sure in general section I read a thread regarding solving water probs.
Hope you can save it
And don´t forget to vote!
Are you sure insurance doesnt cover water damage? I thought warranty didnt, but insurance covers from what I know any incidents. U might want to double check that. And as for SPB Mobile shell no they wont care about that.
And if the rice idea doesnt work, then take the phone and put it under direct sunlight for 4 hours with the screen facing down and no battery or battery cover. If you are in winter where you live, then do not put it outside, but keep in a warm room with direct sunlight shining thru for about 4 hours. My Ex's daugther did the same with her pantec and the rice didnt work, but my idea did
orb3000 said:
Shame to hear about your Rhodium
Covering it with rice is a common practice to absorb the humidity
I don´t remember where but I´m sure in general section I read a thread regarding solving water probs.
Hope you can save it
And don´t forget to vote!
Click to expand...
Click to collapse
thanks! the sleep/wake button comes and goes... other than that it seems like its still working good.... . ill see what happens though... i wanna see if my insurances covers it....
AngelDeath said:
Are you sure insurance doesnt cover water damage? I thought warranty didnt, but insurance covers from what I know any incidents. U might want to double check that. And as for SPB Mobile shell no they wont care about that.
And if the rice idea doesnt work, then take the phone and put it under direct sunlight for 4 hours with the screen facing down and no battery or battery cover. If you are in winter where you live, then do not put it outside, but keep in a warm room with direct sunlight shining thru for about 4 hours. My Ex's daugther did the same with her pantec and the rice didnt work, but my idea did
Click to expand...
Click to collapse
u made a good point... now that i think about it i think ur right about the warranty and insurance. even if i have a modded theme from spb mobile shell? if so that would be great! but i hard spl my phone from before... is there a way of them finding out? do i need to do the whole rice thing or place phone in direct sunlight??? that sounds a good idea . should i call a rep or just go to the at&t store?
Sunlight + Rice.
I dropped my old phone into water (completely immersed), but was workign after 2 days of drying.
As for the hacked shell, unless you modified you ROM (HardSPL?) you're OK.
Warranty does not cover water damage, but insurance should.
Rice seriously? LoL
Thats just a silly old myth.
As somebody who has opened up many phones before, I know for a fact that it's just a silly myth people believe in.
Think about it, is the rice going to magically suck the water out of the phone through the tightly sealed housing.
Rice is not going to do anything.
What you need to do is order is some torx screws off ebay and read a disassembly tutorial so that you can dry out your phone the proper way.
http://forum.smartphonejunkie.com/f498/touch-pro-2-basic-disassembly-pictures-56k-warning-192003/
I went snorkeling with my Touch Pro
When I took it back to the service, first thing they looked at is the stickers and told me its water damaged and that warranty is now gone. Firstly, I gave it lots of sunlight, then got a new battery, then opened the whole thing up. Yep, it took me a while but it was cool to have a look inside. What I found is that water did not really hurt it, but salt did. Using a cotton bud and pure alcohol I cleaned up all contact and solder points on PCB.
It works finenow, except the screen has visible marks, almost like dead pixels, where salt ate it away.
Rice seriously? LoL
Thats just a silly old myth.
As somebody who has opened up many phones before, I know for a fact that it's just a silly myth people believe in.
Click to expand...
Click to collapse
Have you ever tried it? If you haven't then how can you be so condesending about it?
As someone who has done this and seen it work ... I believe in it. The phone was not opened. Was not put in direct sunlight but kept in a drawer in a ziploc baggie full of rice. 2 days later it powered on and ran for almost a year before we upgraded my wife to another device. I would bet that if I pulled it out of the drawer and charged the battery it would probably still work but who wants to use a blackberry
As with anything, your milage may vary but it worked fine for me.
kmx said:
Rice seriously? LoL
Thats just a silly old myth.
As somebody who has opened up many phones before, I know for a fact that it's just a silly myth people believe in.
Think about it, is the rice going to magically suck the water out of the phone through the tightly sealed housing.
Rice is not going to do anything.
What you need to do is order is some torx screws off ebay and read a disassembly tutorial so that you can dry out your phone the proper way.
http://forum.smartphonejunkie.com/f498/touch-pro-2-basic-disassembly-pictures-56k-warning-192003/
Click to expand...
Click to collapse
If the housing was really tightly sealed it wouldn't get enough water into it to break the thing. The rice trick won't work if it was anything othan than plain water, but it generally works well for water spills.
kmx said:
Rice seriously? LoL
Thats just a silly old myth.
As somebody who has opened up many phones before, I know for a fact that it's just a silly myth people believe in.
Think about it, is the rice going to magically suck the water out of the phone through the tightly sealed housing.
Rice is not going to do anything.
What you need to do is order is some torx screws off ebay and read a disassembly tutorial so that you can dry out your phone the proper way.
http://forum.smartphonejunkie.com/f498/touch-pro-2-basic-disassembly-pictures-56k-warning-192003/
Click to expand...
Click to collapse
Yes, make sure you add spices, and brown rice for extra flavor.. Seriously, get a clue. It's a dessicant. See http://en.wikipedia.org/wiki/Desiccant
The rice also helps speed up evapouration since it can absorb moisture in the air surrounding the device and it's readily available. You can use absorbing gel used by people like photographers instead if you want, but you can't cook and serve it with your meal afterwards (just kidding).
In fact, you don't need to use rice or any other material at all - take out the batt and leave it to air dry opened, but this can take over a week or two, even longer if the humidity is high.
PS. I read elsewhere an alternative to rice is to submerge it in alcohol, let the alcohol absorb the water then take it out and let the alcohol evapourate....
I also have to admit that it worked for me. The most important thing about water is to try and vacuum it up out of the phone. Hot air just forces it into places it may not have been. I then put it in a jar with rice for about a week. When all was said and done it worked fine. I may have worked anyways but I figured I had nothing to lose.
toawkanavngthded said:
thanks! the sleep/wake button comes and goes... other than that it seems like its still working good.... . ill see what happens though... i wanna see if my insurances covers it....
u made a good point... now that i think about it i think ur right about the warranty and insurance. even if i have a modded theme from spb mobile shell? if so that would be great! but i hard spl my phone from before... is there a way of them finding out? do i need to do the whole rice thing or place phone in direct sunlight??? that sounds a good idea . should i call a rep or just go to the at&t store?
Click to expand...
Click to collapse
I dont know about the hard spl, the SBP mobile shell is not tinkering with it, custom roms, or hard spl might, insurance I dont know, but if anything I would get a stock rom for your carrier, and if you do a search there is a spl reversal which can lock your phone back. And you dont put it under direct sunlight in the rice bag. If rice didnt work, then you put it under direct sunlight screen down in the open air.
As for person who said "mythical" rice. I beg to differ, as someone said it does absorb moisture that is in the air. Rice is not solid, its a grain which any science nut would know is poreous, which just like carbon can adsorb and absorb moisture in the air, hence putting a wet phone in a ziplock bag would indeed remove water and water vapors due to evaporation.
But also take something else into account, the rice idea only works for a certain amount of time, to the person who said they left it in the rice for a week, sorry the rice didnt get rid of the water, normal sequence of water drying did, you could have taken that same phone and left it on your kitchen counter that long and it would have worked just the same.
And as a side note. Salt works too, its just too fine to put a phone into it. And I never thought of the alcohol trick, maybe I'll try that with a phone I could careless about, til then not a chance.
Lastly, anyone who buys bagels by the dozen, if they give you a bakers dozen, get a salt bagel and leave it in the bag with the bagels, helps keep the rest of the bagels fresh
We now return you to our regularly scheduled program, already in progress LOL!
Don't cook the rice first!
thank you all for ur responses. the night i dropped my phone i just took out the battery and just wiped everything as dry as i can. i had to charge my phone that night and so i did it anyways... the next morning it charged fine and everything was working fine... that night my sleep/wake button started functioning correctly. the only problem i have is that my vibration isnt as strong but its ok. so i guess i got lucky? i have insurance so if anything starts acting up ill try my best to switch it.
If you have insurance (you pay monthly) then it is covered, but there is a $125 deductible I believe. If you do not have insurance and are referring to the 1-year warranty then no, water damage is not covered.
petard said:
If you have insurance (you pay monthly) then it is covered, but there is a $125 deductible I believe. If you do not have insurance and are referring to the 1-year warranty then no, water damage is not covered.
Click to expand...
Click to collapse
My insurance paper says that the insurance co pay is 50 bucks. That being said, if you can go without your phone for a few days, pay the deductible and tell em that you LOST your phone. Asurion does cover the phone if it is lost.
PS. The rice does actually work. I didn't believe it myself, But I had to do that once on my Touch Pro 1 and two days later the phone was completely dry, and worked like a charm.
jmy72 said:
My insurance paper says that the insurance co pay is 50 bucks. That being said, if you can go without your phone for a few days, pay the deductible and tell em that you LOST your phone. Asurion does cover the phone if it is lost.
PS. The rice does actually work. I didn't believe it myself, But I had to do that once on my Touch Pro 1 and two days later the phone was completely dry, and worked like a charm.
Click to expand...
Click to collapse
lost phones are an $80 co-pay through asurion, not sure how the other insurance companies are.
*edit*
I've had an experience dropping my Treo 700wx in water. The screen was shot for a couple days (and you could see the receding water). After about 4 days it was working fine with just about everything but I still replaced the phone and the replacement refurbished phone was worse than the original. Basically water damage isn't too bad, just let it dry and don't use it for a couple days. It will shorten its lifespan, but it will still work. At the very least its better than getting a refurbished phone, because in my experience those seem to have more problems.
Has anyone done it before? There is a video on youtube, but it only goes as far as the keyboard. I'm looking to get to the LCD to fix/replace it because of discoloration from water damage. Anyone thinks it's possible?
I remember a thread like this being made a while ago...if you're on a computer, just search and you should find it. I can't post a link, but I think the guy in that thread replaced it succesfully.
There was also alotta chatter about insurance covering it
Sent from my SPH-D700 using XDA App
Here's a tear down of the Epic 4G:
http://www.chipworks.com/en/technical-competitive-analysis/resources/recent-teardowns/2010/09/teardown-of-the-samsung-epic-4g-smart-phone/
Try asking a repair technician. The truth is, body repairs can be quite pricey - to the point where you might as well be getting a new phone in many cases.
I watched someone else take mine apart. There are an awful lot of little screws, but you can definitely seperate the case, the screen, and the actual guts in about 10 or 15 minutes.
DiGi760 said:
I watched someone else take mine apart. There are an awful lot of little screws, but you can definitely seperate the case, the screen, and the actual guts in about 10 or 15 minutes.
Click to expand...
Click to collapse
The question then is can you get it back together ;-)
Sent from my ext4 Epic 4G running Bonsai4all 1.1.3!
sauron0101 said:
Here's a tear down of the Epic 4G:
http://www.chipworks.com/en/technic.../teardown-of-the-samsung-epic-4g-smart-phone/
Try asking a repair technician. The truth is, body repairs can be quite pricey - to the point where you might as well be getting a new phone in many cases.
Click to expand...
Click to collapse
I had TEP with my BB curve and I smashed it [was REALLLLLLY angry at my gf...she wasn't worth the BB :'( ] and I took it to a corporate store, and he fixed the screen in front of my face and I walked right out lol but that was a couple years ago
Sent from my SPH-D700 using XDA App
The phone still works, I just wouldn't want to look at pictures or watch videos on it since the color is all messed up. It's been about 2 weeks since the accident and it's still going! I just want to study this just for reference just in case it does go out. The replacement cost $60 on ebay, so I'd definitely do that, especially when I don't have insurance with Sprint (I think it still costs more than DIY) and I don't think Samsung fixes water damage through its warranty.
Oh well.
Thanks for the link! I'll check it out!
being a technician at an indirect sprint store, its a pain in the ass to separate the LED screen and the glass itself. the very best way to do it is either go to a 3rd party sprint store that has a full service(repair) center and either have them do an exchange if the tech is a nice guy (considering its water damage) or replace the part (which would be free as long as you have TEP). PM me with more questions if you have them
kzn said:
Has anyone done it before? There is a video on youtube, but it only goes as far as the keyboard. I'm looking to get to the LCD to fix/replace it because of discoloration from water damage. Anyone thinks it's possible?
Click to expand...
Click to collapse
Yeah, I've done it at least 20-30 times now. It's EXTREMELY difficult to get the lcd out and you'll more than likely end up breaking your phone.
br//0k3/n said:
Yeah, I've done it at least 20-30 times now. It's EXTREMELY difficult to get the lcd out and you'll more than likely end up breaking your phone.
Click to expand...
Click to collapse
Yea, you're definitely right about the LED itself. It's close to paper thin and made of a glass type material. it will break if you try to get it out. it's glued pretty good.
flawlessbmxr said:
Yea, you're definitely right about the LED itself. It's close to paper thin and made of a glass type material. it will break if you try to get it out. it's glued pretty good.
Click to expand...
Click to collapse
I took mine apart, lots of screws. Honestly the hardest part was removing the back cover that goes over the motherboard. I used a very small flathead to pry up underneath where the little notches are on the side. There's a lot of clip points and 2 of them at the battery are very hard to get off. Once that's off, the rest is cake. Separating the screen was a non-issue, as mine was already broken/cracked.
just to chim,e in on this ancient thread. i used a guitar pick instead of a flat head. i thought a metal screwdriver would scuff and mar up the plastic cover over the board.
Another protip: the notches on the second to last plastic cover serve a purpose -getting that back half to snap onto the phone is a huge pain in the ass, - i put a flathead into the slits and pushed down and snap snap snap snap motherboard cover was back in and my battery case didn't bulge.
kzn said:
Has anyone done it before? There is a video on youtube, but it only goes as far as the keyboard. I'm looking to get to the LCD to fix/replace it because of discoloration from water damage. Anyone thinks it's possible?
Click to expand...
Click to collapse
I've replaced my LED screen before by myself, took a few hours. This video helped me.
http://www.youtube.com/watch?v=IeO89VGAPuU
zvonkorp said:
I took mine apart, lots of screws. Honestly the hardest part was removing the back cover that goes over the motherboard. I used a very small flathead to pry up underneath where the little notches are on the side. There's a lot of clip points and 2 of them at the battery are very hard to get off. Once that's off, the rest is cake. Separating the screen was a non-issue, as mine was already broken/cracked.
Click to expand...
Click to collapse
Is there a water sensor inside the phone, I've always wondered if the battery was the only place
Sent from my SPH-D700 using Tapatalk
was hoping for a bit of help... the bottom left of my screen has come away from the phone slightly. I can push it back and it stick for about half a second then back to normal. not sticking out a lot but enough for dust and bits to get under the screen. I therefore want to open up the phone and see if i can fix it and clean away the gathered dust underneath.
has anyone done this before? if so i'd really appreciate some advice on how i go about it.i have insurance if it all goes t*ts up!
cheers
I know someone else recently asked about taking their DHD apart.
Some of these YouTube vids might help.
http://www.youtube.com/results?search_query=desire+hd+disassembly&aq=f
trust me you don't wanna do that it is so complicated that even jesus himself would send it to repair centre, lcd is glude to middel plate and middel plate is glued to tow boards it takes lot of nervs and skill to tear it apart and even more to put it all back together, don't do that or your dhd will suffer the same fate as mine(a very ''well-educated'' tehnician serviced mine he did the job almost as a butcher lol) don't do it take it to repair centre take my word for it
bruno_123 said:
trust me you don't wanna do that it is so complicated that even jesus himself would send it to repair centre, lcd is glude to middel plate and middel plate is glued to tow boards it takes lot of nervs and skill to tear it apart and even more to put it all back together, don't do that or your dhd will suffer the same fate as mine(a very ''well-educated'' tehnician serviced mine he did the job almost as a butcher lol) don't do it take it to repair centre take my word for it
Click to expand...
Click to collapse
100% agree with you. Saw an 8 min video on it and it involves removing all the components in order to get to the lcd. was hoping it would a lot simpler. will contact htc and see if they can do anything with it otherwise i'll just get over it and hope ti doesnt get worse.
cheers
PLEASE don't take apart your Desire.
I took apart my HD2 to attempt a minor fix, even though I followed the leaked HTC HD2 disassembly video...I FU**ED up bigtime!
Even though at the time I was 100% confident at doing it and looked real easy...trust me....you end up like I did, by thinking "oh SH*T!! I wish I didn't do that!"
matt
haha yeah i've definitely lost a lot of confidence after seeing the video. best leave it for a pro...or just leave it
cheers
Dont try this at home...haha
Send it to service centre....
Sent from my HTC Desire HD using XDA App
if service centre broke ur phone, claim it from them.
I read about screem gap but i was unsure what exactly was meant. I just took a closer look and found out that there is a tiny gap between my screen and phone on top in which dirt fills in and it pisses me off. I havent dropped my screen once and if i push the top left part of my phone i can hear a sort of "click".does that make my phone faulty? Im really annoyed vy the dirt that fills in... Apart from rhat phone has no problems.
shadehh said:
I read about screem gap but i was unsure what exactly was meant. I just took a closer look and found out that there is a tiny gap between my screen and phone on top in which dirt fills in and it pisses me off. I havent dropped my screen once and if i push the top left part of my phone i can hear a sort of "click".does that make my phone faulty? Im really annoyed vy the dirt that fills in... Apart from rhat phone has no problems.
Click to expand...
Click to collapse
send it back. that is what i am doing. left hand side of the phone between the screen and the plastic you can see dust getting inside there to. plus if you press the left hand side tad hard you can hear it creaking as well. i called HTC to see if they could replace it for me straight away without sending it for repairs..waiting for an outcome tomorrow...if they say no i will just send it for repairs and hope they find the problem and either fix it or replace it then...i know it will drag for a week but at least that way you know one way or the other it will get fixed...
i was going to say if it does not bug you then leave it..but you sound just like me that even though the phone works fine it will bug you cause you know it is there
should i go to my provider or directly cpntact htc? And just to understand it better. Gaps are not supposed to be there, am i right?
shadehh said:
should i go to my provider or directly cpntact htc? And just to understand it better. Gaps are not supposed to be there, am i right?
Click to expand...
Click to collapse
Dont replace it as you have no other problems. Go to HTC repair center and just fix it. If you replace there may be a chance of getting more faultier one.
Sent from my HTC One X using Tapatalk 2
Living in austria, where to check for such a repair center?
forumhookersdotcom said:
Dont replace it as you have no other problems. Go to HTC repair center and just fix it. If you replace there may be a chance of getting more faultier one.
Sent from my HTC One X using Tapatalk 2
Click to expand...
Click to collapse
have to agree with that as well. but at the same time new batch of phones get send out so you never know. just go to HTC site and do a locator for your country my friend
shadehh said:
Living in austria, where to check for such a repair center?
Click to expand...
Click to collapse
Have a look at this . May be useful
http://www.htc-floorsystems.com/en/HTCGlobal/HTCOffices/HTCGermany/Contacts.aspx
Sent from my HTC One X using Tapatalk 2
Thank you all and especially goku80 for fast replies. Gotta love xda community
shadehh said:
Thank you all and especially goku80 for fast replies. Gotta love xda community
Click to expand...
Click to collapse
no problem my friend. i feel your pain and know what you are going through. i will keep you updated with my one and what happens..keep me updated with yours as well
It amazes me some of the reasons people will find to return an otherwise perfect handset. Considering the amount of serious problems floating about this phone, I don't think a creak or 1mm gap between the bezel and screen constitutes a return. Get over it and enjoy the phone.
Eddzz!! said:
It amazes me some of the reasons people will find to return an otherwise perfect handset. Considering the amount of serious problems floating about this phone, I don't think a creak or 1mm gap between the bezel and screen constitutes a return. Get over it and enjoy the phone.
Click to expand...
Click to collapse
oh really..seriously i wonder if you had a gap how would you feel about your perfect phone? everyone to their opinion. i can live with it no problem..but the fact knowing that it is there will bug the **** out of me hence why i am going through what i am right now
I had a creaky SGS for 2 years. I still have it now and it works and looks as good as it did on day one.
Eddzz!! said:
I had a creaky SGS for 2 years. I still have it now and it works and looks as good as it did on day one.
Click to expand...
Click to collapse
well i will see what they say tomorrow..if they replace it for me all is good..but if they do not and want to fix it ehh i kinda have to think twice being without my phone for a week
Ive heard that the one x was made in 2 different countrys taiwan and china... china being the worst built ones buttt I must have a really faulty dhd. I've had it for 10 months now and my screen moves, doesn't fit right on the phone as there should be a lip round it but isn't my speaker isn't straight so is sloping. Looks like the cnc machine hasn't cut it right. Power button is really recessed too far in..... I think a little sqweek is nothing to really worry about if the screen falls out then ya I'd send it back.
Sent from my Desire HD using XDA
htcmodteam said:
Ive heard that the one x was made in 2 different countrys taiwan and china... china being the worst built ones buttt I must have a really faulty dhd. I've had it for 10 months now and my screen moves, doesn't fit right on the phone as there should be a lip round it but isn't my speaker isn't straight so is sloping. Looks like the cnc machine hasn't cut it right. Power button is really recessed too far in..... I think a little sqweek is nothing to really worry about if the screen falls out then ya I'd send it back.
Sent from my Desire HD using XDA
Click to expand...
Click to collapse
well that is what worries me about the whole damn thing..if it gets to hot to soon and in two months down the line the screen actually does fall out
TBH ive just checked mine and it does have a slight gap with lint building up already (bare in mind ive had this phone 2 days) Also have the yellow blotch on the screen AND a dead pixel. This is by far the best phone ive ever owned...But my word these little niggles are grating on my moobs! Ive never had to send a phone off to a repair centre before but im not really willing to put up with the problems the phone has (however ridiculously small they seem to some ) You expect some software issues in an early batch, but dead pixels, discoloured screens, gaps occuring out of nowhere between the screen, its a bit much really! Im gunna have to get it sent off soon i think, gutted!
how do you clean the dust build up?
abuds87 said:
how do you clean the dust build up?
Click to expand...
Click to collapse
Use a screwdriver.
P.S. http://forum.xda-developers.com/showthread.php?p=27066789
abuds87 said:
how do you clean the dust build up?
Click to expand...
Click to collapse
Vacuum cleaner with a soft piece of cloth on the vacuum tube to avoid scratches.
Just another option
To the OP: May I ask what serial your phone has?
Cheers.
Eddzz!! said:
It amazes me some of the reasons people will find to return an otherwise perfect handset. Considering the amount of serious problems floating about this phone, I don't think a creak or 1mm gap between the bezel and screen constitutes a return. Get over it and enjoy the phone.
Click to expand...
Click to collapse
Do you even realize how big 1mm is?!!!! Get a ruler and see please....
I doubt even a blind person could enjoy a phone with a gap big as that. You would not just see this, but also feel.
I have a gap that's about 0,1-2 mm big (measuring with paper, which is about that in average I think 0,1 till 0,3 I think but also not sure) and its around the whole screen on both sides of the ring.
Ugh...1mm...
But seriously guys, how big are the gaps it makes you return it?
I mean should I return it with 0,1 mm ? (maybe less) seen a bigger gap on SGS 2.
Alcohol problems
So, I was rubbing off a sticker from the back of my phone using a small towel dipped in pure alcohol. This phone is supposed to be waterproof and I put my back cover on the front for extra security. But, after I was done, dried it and everything, I realized that some alcohol had gotten inside the screen, I have no idea why. The whole display was dark pruple-ish and covered in stains and some weird things like dark dark spots and lines. I researched it ans found out that it was okay because alcohol evaporates really easily, so I decided to use it for a bit, since I have huge overheating issues (often going up to about 45-50°C upon usage). After half an hour of usage (it had gotten pretty hot), the display seemed to become a little bit clearer and less dark, but I decided that I should stop using it in fear of moving some bubble or ruining my already dying screen, so I put it to charge and left it alone. I was relying on my country's hot weather to finish the job, and I was checking on it every once in a while. At first, it seemed to get better but suddenly, after about 2 or 3 hours, the screen stopped turning on at all. Neuther the display nor the touch were working anymore, but sound (modifying volume) and vibration (haptic feedback for holding down "power") worked really well. I tried to restarted (volume up + power), but nothing more than some vibrations and jingles. Currently, my phone is turned off (volume down + power) and I'll leave it like this overnight, to see if anything improves tomorrow.
So, I need to know. Is my screen ruined and needs changing, or simply evaporating the alcohol will fix everything? Also, if I have to change my phone, is there a way to use HTC backup to transfer data without the "old" phone?
Thank you in advance!
Laslas19 said:
So, I need to know. Is my screen ruined and needs changing, or simply evaporating the alcohol will fix everything? Also, if I have to change my phone, is there a way to use HTC backup to transfer data without the "old" phone?
Thank you in advance!
Click to expand...
Click to collapse
Hello mate, bad luck with that happening..
First off the phone is not waterproof, it does have an ip rating but it's not up there with phones you can take with you for a dip.
As for the moisture, try a silica gel pack in an air tight bag for a few hours or over night, there are packs you can buy online for this specific treatment, if the alcohol has hit something critical then it could be game over..
Try the drying out techniques, you can find many of them online..
Drying the alcohol up shouldn't be hard but like I said if damage is done then it's done mate.
Just one question, why use alcohol on your phone? Wouldn't a baby wipe or a damp cloth do the same?
dladz said:
Hello mate, bad luck with that happening..
First off the phone is not waterproof, it does have an ip rating but it's not up there with phones you can take with you for a dip.
As for the moisture, try a silica gel pack in an air tight bag for a few hours or over night, there are packs you can buy online for this specific treatment, if the alcohol has hit something critical then it could be game over..
Try the drying out techniques, you can find many of them online..
Just one question, why use alcohol on your phone? Wouldn't a baby wipe or a damp cloth do the same?
Click to expand...
Click to collapse
First of all, thanks a lot for your help, I will try your suggestions and keep you up to date.
Second of all, by "game over" do you mean for the screen or the entire phone? Because the phone itself seems to work just fine apart from the screen.
And, finally, that was a really tenacious sticker that I tried to remove for days. I know it sounds stupid that I used alcohol but nothing else worked. Good thing I didn't resolve to boiling water first. There is one positive point about this whole story: the sticker is now completely gone.
EDIT: I forgot to say that I made a mistake: the phone is not supposed to be "waterproof" as I previously said, but it is clearly stated on its booklet that it is "splash proof". I guess that does make a difference and I ask to be excused from my dumbness.
How much alcohol did you use... You're only meant to damp a cloth an rub lightly.. It would seem to me you poured it on.
I wish I stole my HTC M9. It's a pile of ****.
shivadow said:
How much alcohol did you use... You're only meant to damp a cloth an rub lightly.. It would seem to me you poured it on.
I wish I stole my HTC M9. It's a pile of ****.
Click to expand...
Click to collapse
Well "rubbing lightly" surely isn't the word because it didn't work but I did damp a cloth and rubbed strongly enough for the alcohol to actually come out of the cloth and slide off the sides of the phone. I did meticulously dry it with tissues tho, but it must have been too late.
Oh, and by the way, I do hear my new email jingle coming out of it (because turns out power+volume down can't turn it off, I can just restart it with power+volume up) when I get an email notification from xda. So I am guaranteed that wifi, gmail and the speakers still work at least. I think the main problem is the screen.
I think something either controlling or part of the screen has popped by shorting out.
It's tough to call but the fact the phone still responds is promising!.
Give htc a call and just tell them it went off one day and wouldn't come on. Any evidence should have literally evaporated into thin air by then. Hopefully they'll arrange something.
I wish I stole my HTC M9. It's a pile of ****.
shivadow said:
I think something either controlling or part of the screen has popped by shorting out.
It's tough to call but the fact the phone still responds is promising!.
Give htc a call and just tell them it went off one day and wouldn't come on. Any evidence should have literally evaporated into thin air by then. Hopefully they'll arrange something.
I wish I stole my HTC M9. It's a pile of ****.
Click to expand...
Click to collapse
Thank you for your help! Unfortunately if I want to send my phone to HTC I'll have to send it to another country because there's not much support here and it will be really complicated. But, if I understand correctly, just changing the screen should fix the problem. It won't be cheap but definitely cheaper and easier than getting and setting up a new phone.
Thanks again for the advice!
Laslas19 said:
Thank you for your help! Unfortunately if I want to send my phone to HTC I'll have to send it to another country because there's not much support here and it will be really complicated. But, if I understand correctly, just changing the screen should fix the problem. It won't be cheap but definitely cheaper and easier than getting and setting up a new phone.
Thanks again for the advice!
Click to expand...
Click to collapse
Changing the screen should work, just as long as it is 100% the screen and not some controller on the motherboard. Personally I agree with the other user who suggested sending it to htc, in all fairness htc should help you out in this case, it's obvious that it shouldn't have went off in that fashion.
I've sent my prime off overseas before, I get it back in around 5 days, great service. At the very least, speak with HTC and see what can be done and expected timelines. Changing the screen even on a one x was a tedious process, I've broken a device in the process, wasn't even mine so please take care if you go down that road, not to mention it's not exactly cheap.
BTW when I said game over I was referring to a simple method not being available to fix your phone and lastly, if you swap out the screen, you will more than likely lose your warranty.
Click thanks to the ppl who've tried to help you BTW
---------- Post added at 08:09 AM ---------- Previous post was at 08:06 AM ----------
shivadow said:
I wish I stole my HTC M9. It's a pile of ****.
Click to expand...
Click to collapse
? Can't think of a better phone out at the moment, in fact I know there isn't.. Maybe the one plus 2? Nah I'd stick with the HTC.