Artemis flashing guide - Upgrading, Modifying and Unlocking

Hi Everybody.....,
I have seen a lot of people posting that they need a proper process of how to flash the HTC Artemis with a Custom ROM.
Flashing process is not so hard as it sounds. It is a very very very simple process, but still some people find it very difficult to do it or they are very much afraid whether they will brick their device.
So I decided to start this post so that it could be very much helpful to a Newbie.
Do not worry guys, even I was new in this arena a year before, but now you see I have mastered this process.
Follow these simple STEPS One by One and you will see your HTC Artemis in a Brand New Custom ROM…..!!!!
Every post contains a Step by Step procedure.
Post 1 : Connecting your HTC Artemis to your Laptop/PC.
Post 2 : SPL Unlocking your HTC Artemis
Post 3 : Flashing Your Device
[email protected]@[email protected]

POST 2
Follow these PRIMARY STEPS to connect your HTC Artemis to your Laptop/PC so that no mistake is made in connection while you flash your device.
1.First of all, insert the HTC Application CD (which you received when you purchased your device) in Disk Drive of your Laptop/PC.
2.Install Windows Active Sync from that CD into your Laptop/PC. NOTE: Do not connect your device while installing the Active Sync Software.
3.Now, once the software is installed RESTART you PC.
4.Connect you device HTC Artemis to your PC and follow the installation procedure.
5.After you complete the Installation, make sure the application looks like this.
Now, your device is connected and you need to switch to Post 2.

POST 1
Now, these are the SECONDARY STEPS to prepare yourself with all the tools for flashing you HTC Artemis.
Before we continue, make a note of the following instructions VERY CLEARLY.
NOTE: Do not DISCONNECT or LAUNCH any program in your PDA or PC during the update process.
NOTE: Please be sure that your phone battery is 100% charged before you start the update process.
NOTE: These steps are EXTREMELY necessary to be followed, because if you miss these steps, you will result in your device getting bricked.
1.First of all you need to SPL Unlock your device. For this, you need to download a software to SPL Unlock you phone.
2.You can download the Artemis USPL from the link below.
3.After you download the file, extract it and follow the instruction given.
4.Double click on the start_uspl program. A CMD window will show up and your USPL Unlocking process STARTS.
5.This process takes about 10 minutes depending upon the CPU speed, so keep patience.
6.After the process completes, the CMD window will vanish and a ROM Update Utility will start.
7.Your phone will be temporarily get disconnected from your PC but will regain connection after a few minutes. So be patient as your phone restarts and establishes connection.
8.After the phone establishes connection with the PC again, follow the steps as per the ROM Update Utility.
9.After the process completes, your phone will restart automatically. Now, check your phone when it restarts.
10.As soon as the phone restarts, it shows the following details:
IPL 3.xx.xxxx
SPL 1.11.0000
GSM 03.xx.xx, here x may be any number.
11.Now, if the phone shows SPL 1.11.0000 than your phone is ready to be flashed.
12.But, if it shows SPL as 3.xx.xxxx, where x may be any number than your SPL is not Unlocked and you need to follow all the above steps in this post again.
13.If your phone shows SPL 1.11.0000 on restart, then please follow the steps in the next post.
NOTE: DO NOT MANUALLY RESTART YOUR ARTEMIS OR DISCONNECT IT FROM YOUR PC AFTER THE SPL UNLOCKING PROCESS IS COMPLETED. PLEASE KEEP THE DEVICE CONNECTED TO YOUR PC AND FOLLOW THE STEPS IN THE NEXT POST.:mad:

Where is the link????

APOLOGIES
imhere4xxx said:
Where is the link????
Click to expand...
Click to collapse
I apologize for not posting the link due to certain reasons...
But, here is the link to LATEST WM6.5 ROM
http://www.megaupload.com/?d=H8OZONJ0
I apologize again...
I will be posting some links in a few days again....
Thank You

Related

HELP diamond hard spl update problem!!

as i write, my diamond is sitting near me, with a black screen
what i did:
1. tried to hard spl 1.4 olinex developer
2. error after starting update at 0% stating that connection to device could not be established
3. i read this on 'the bible':
"If you are having problems with the device entering SSPL automatically, please copy the file "SSPLManual.exe"; from the directory you unzipped the installation package to the device and run it (recommended to run it from the Windows folder). INSTALLING THIS WILL HARD-RESET THE DEVICE. Your device screen will turn black and you can start from step 2 of this guide"
4. i disconnected the phone and then ran the SSPLManual.exe
5. the screen turned black and it stayed so ever since (20 minutes ago, i guess)
Did i make a big mistake by disconnecting the device? should i wait a little longer, or is it safe to soft-reset (small red button) and restart everything?
PLS tell me my device isn't bricked or something... there was no warning there that SSPLManual.exe should be ran while still connected :|
PLEASE give me a straight and fast answer to this, after that the thread can be deleted... i am desperate...
thank you

Problems installing, wm6.5

hello all,
i was about to install wm6.5, but i cant get it done.
Mobile: Htc touch diamond (ofcourse)
Rom: 1.37.172.3 NLD (i went to this thread: http://forum.xda-developers.com/showthread.php?t=400402 , and did everything they said, and the rom update was succeful.. so i dont understand why my mobile says its this rom.)
radio: 1.00.25.03
I followed this steps:
How to install the Windows Mobile 6.5 in your HTC mobile
This howto was conducted on GSM HTC Touch Diamond. For all other HTC sets running the Windows 6.5 the consequences will be the same.
Requirement
HTC Touch Diamond or Touch Pro (GSM only)
Windows Mobile 6.5 ROM (Choices: Diamond , Pro )
Account at XDA Developers(free)
Windows PC set up to sync with your handset
Device flashing utility
bootloader(Diamond , Pro )
Device Radio (Diamond , Pro ). Ensure that you download the Original list.
Now, if you are done with the requirements its time to back up with your contacts and personal info. For this you might take the help of Microsoft's free online service called My Phone. Remember, the installation would remove the software installed in your device, so don't forget to keep a back up.
Install the bootloader
What you need to know is that you are installing an unofficial softwar, something that your mobile phone is not used to do. To begin with install a new bootloader hardSPL on the device. This will allow your handset to accept third party services like the Windows Mobile ROM. Go ahead with the steps
Step 1: Connect your mobile phone to your Windows PC. Establish the ActiveSync (on XP) or Sync Center (on Vista, or Windows 7) connection to your device. Make sure the connection is active. To check this see if there is a bidirectional arrow in your Phones taskbar.
Step 2: Extract the bootloader you've downloaded and note the location
Step 3: Now find the extracted files and run the executable file ( it is usually called ROMUpdateUtility.exe)
Step 4: Follow the instructions. The software will perform a number of checks. You must make sure you have the following
i) The handset has 50 % battery life in your phone
ii) The correct bootloader
iii) host computer that doesn't go down
Step 5: Can you see the paired progress bars on your phone and computer screen. This part of the process doesn't take long as it is a small piece of software.
Step 6: Now Restart your phone. The small text will appear in the corner of your Windows Mobile splash screen. This might be unfamiliar.
If the utility runs completely, the device will be restarted on its own.
Install a new device radio
Installing a fresh Radio onto the device usually won't make much of a change in how your phone works. Some radios can improve reception on certain networks. Let's get on with the technique
Step 1: Connect your phone to the PC
Step 2: Extract the download radio files and note their location
In case, the radio comes with a bootloader, jump to step 5
Step 3: Extract the downloaded bootloader, using the location
Step 4: Copy the extracted radio file, with an .NBH extension to the directory where you have placed the bootloader
Step 5: Run the bootloader
Step 6: Perform the instruction in step 4 and 5 provided in the bootloader installation procedure
Step 7: Allow the phone to restart. This won't bring in major changes, but you might have to make some minor changes in the network setup.
Install Windows Mobile 6.5
This is where you get down to installing the new OS.
Step 1: Connect the Phone with PC
Step 2: Extract the downloaded bootloader again, but to a different location
Step 3: Extract the Windows Mobile 6.5 ROM to the same directory where you have the bootloader. It would be an .NBH file of about 80-100 MB.
Step 4: Now Run the bootloader and follow the instructions.
Step 5: Wait, the process will take 15 to 20 minutes
Step 6: After your phone is reset, the Windows Mobile 6.5 splash screen will appear. It appears somewhat hacked. But, your job is done.
Step 7: WinMo would automatically anticipate your connection settings and apply the appropriate connection settings. In case, it doesn't, you can do it from the device's Settings page, found in the top level of the new start menu.
Click to expand...
Click to collapse
Ok now the problem:
The first step was succesful, i installed the bootloader.
Then i went to the radio update: So i downloaded the radio version: 1.09.25.23. There are 2 files in that: 1.09.25.23.nbh and customRUU.
I first clicked the costomRUU twice, and started the thing, but it got stucked. So i went back to the webpage to look, and i found i had to copy the stuff into the bootloader shizzle. So i copied 1.09.25.23.nbh and customRUU into the map with: enterbootloader, errorbattery, errorusb, modelID, rapitool, romupdateutility.cgf, romupdateutility, RUU_signed.nbh, RUUgetinfo, RUURescource.dll, SSPL-Manual.. And i double-clicked the romupdateutility. I did everything the thing said, But after a short period of time, like 3 minutes, an error occured. So i did the same after resetting my device.. same problem. The same problem occures when i try this with the wm6.5 file. I downloaded BsB65K. from: http://forum.xda-developers.com/showthread.php?t=506533. I copied the nbh-file into the bootloader thing, runned the romupdateutility, and got same problems as with teh radio, what am i doing wrong?
Kind regards, Michiel.
The radio did come with a bootloader - customRUU.exe, skip to step 5. I know you did try using the customRUU and it got stuck; do it again. Extract the original radio file you downloaded, don't piss around with the files you've copied around at this point. Extract it and double click the customRUU after you've connected via ActiveSync. Once that's done extract the ROM you want, copy it to the root of the internal storage, press reset then hold vol down and <- at the same time until you get the boot menu, press power once to install the new ROM.
Thanks for the helping.
But, is this for radio only?
And i still have the problem. I did as u said:
-extract the radio files on the pc: 1.09.25.23.nbh and customRUU
-double click customruu, (do i have to run the whole setup, or just the first step? )
-what is the rom? the .nbh-file? because i copied the nbh into my storage of my mobile device.
-then i do the reset.
so i have to know how i have to run the setup, btw, at the reset or do i have to run it before.
regards
Did you Hard-spl? if not, thats your problem.
Nope that was radio and ROM.
Extract the files from the radio file. Connect the phone via activesync. Run the customRUU. Follow the instructions on the screen. Once it completes your radio is updated.
Now extract the ROM you want to upgrade to. Copy the diaming.nbh file from it into your internal storage. Press reset and hold vol down and <- until you get the boot menu. One option will be to install the DIAMING.nbh by pressing the power button. Press the power button once.
It will tell you when it's complete. Reset and enjoy. The method I describe is faster and easier than using activesync to install the new ROM.
When i hold reset+vol down, i get a 3 color+white screen.. witch says not except some rom information. etc.
And yes i did hardspl. i got rom SPL- 1.30 Olinex.
upgrade your hard-spl to: RUU_Signed_1_93OliNex_HSPL_UnsignedEdition
download here: http://rapidshare.de/files/40191554/RUU_Signed_1_93OliNex_HSPL_UnsignedEdition.zip.html click free user and you are ready to go...
hope this helps you
Is it a problem im having a vodafone device. bcs i hate the vodafone theme etc.. hate all the vodafone stuff actually
(got other theme now.. but anyway)
May I ask what the error is you're getting?
Thank you very much all, its working perfect.
this one can be closed

How to upgrade ROm with nbh file

As newbie on this, anyone please guide me step by step to upgrade my P3300 rom with nbh file. My device is unlock already with current ROM 5.2.1908 (build 18125.0.4.2).
The procedure is given in almost every thread. It's simple really. Is your SPL version anything other than 1.11.0000 or 1.11.cmon? If yes then your phone is not unlocked. Unlock your phone by running USPL from here or the updated USPL from here.
Check if the USPL has worked by checking your SPL number. During phone booting at the white HTC screen your SPL should show either 1.11.0000 ir 1.11.cmon.
If it does you are free to flash any ROM. Get the ROM of your choice, put your phone into bootloader mode by pressing the voice record, power key and reset button simultaenously for about 5 seconds till you see a three colored screen. Attach it with USB and flash the rom using RUU.
thanks randythered for ur reply. I did w/o problem on USPL but how to use the nbh extention? where that nbh file I shall put in? pc or devise or on specific folder? I got the three colors already, then what next? pl. enlighted
stacknickel said:
thanks randythered for ur reply. I did w/o problem on USPL but how to use the nbh extention? where that nbh file I shall put in? pc or devise or on specific folder? I got the three colors already, then what next? pl. enlighted
Click to expand...
Click to collapse
do u have only .nbh file or along with .nbh file any other files are there ?
generally along with the .nbh file there are other files like romupdateutuility.exe etc.,
download those files also and save those files into your PC.
after unlocking your device then staup the device with bootloader mode (three color screen)
connect the Device with the PC by USB cable.
in the device display u will a word USB (left bottom corner)
run the Romupdateutility from the PC...
the process will guide u next steps ...
after the completion u will have new OS
Last I would recommend tht u also upgrade you Radio ROM (this is responsible for all the communication functions of ur phone i.e. calls, GPS, WiFi etc) which will enhance the communication capabilities.
Radio ROMs Link : http://wiki.xda-developers.com/index..._RadioUpgrades.
Note : before flashing any ROM or upgrading the RADIO kindly CID unlock your device or you will end up the with bricked device .
You can download my ROMs, they come with the full package
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
stacknickel said:
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
Click to expand...
Click to collapse
your device not properly CID unlocked...
unlock the device properly with USPL...
stacknickel said:
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
Click to expand...
Click to collapse
As sixthsigma said, did you check if the phone is correctly unlocked? Is the SPL showing 1.11.0000 or 1.11.cmon?
Secondly, what OS are you flashing on? XP, Vista or Windows 7?
Hi Randythered, IPL 1.25.0001 and SPL 1.27.0000
I am using your ROM RtR Manila v1.0
using XP
Well, firstly thank you for wanting to try out my ROM
Secondly, you haven't unlocked your phone properly yet. The SPL must be 1.11.0000 or1.11.cmon, depending on which USPL you use.
strange... hv tried several time but w/o luck...
now I notice that it cut out after '70' and jump into 100 with disconnecting
any choices of other USPL instead of the one attached here?
Did you flash the old USPL or the new one which is nosize? It is preferable to install the old one first. And then go for the cmon nosize USPL if need be.
From a noob to a noob
Hi, heres the procedure for upgrading your rom put as noob friendly as i can put it.
WHAT YOU NEED
1. HTC Artemis p3300
2. computer running Windows XP with activesync installed
3. Usb cable to connect to computer
4. The new rom that you want to flash
5. And USPL which can be downloaded at this page http://forum.xda-developers.com/showthread.php?t=311403
NB: For most of the newer roms you will probably need the updated nosize version of uspl http://forum.xda-developers.com/showthread.php?t=521406
PREPARATION
NB: Anything you need to backup or keep from your device do it now.
NB: in some cases you may have to hard reset your device before it will take the flash
1. Extract Uspl to your desktop
2. Extract the rom you downloaded to your desktop
3. Remove your sim chip and memory card from your device
4. Reset your device and sync with windows xp
UPDATING
1. In the USPL folder run the program called "start_uspl" and let it do its thing in the dos window,in
my case it goes to 70 and then jumps to 100,if you have been watching your device screen you will
see the linux penguin for a few seconds and it will change to a white screen.
A window will popup on your computer, do as it requests, when finished it will reset your device.
Sync your device with your computer again.
2. In your downloaded rom folder you should find a file called "ROMUpdateUtility.exe" or "Ruu.exe", run
it and a window will popup, do as it requests.
Your device screen will go tri-color(red,green,blue) and the rom update will begin, wait till it
finishes and thats it.
thanks soloman1 and others
finally I got it with removing the sim card and memory card prior to upgrading
stacknickel said:
thanks soloman1 and others
finally I got it with removing the sim card and memory card prior to upgrading
Click to expand...
Click to collapse
same ting got me with my first rom thats why i thought to put it in, happy flashing (not in the naked way )
Lol I can't belive I forgot to tell you that!
It's ok. Thanks to u too randythered.
Do you have dedicate Manila in cab file?
Thank you, here you go!
sixthsigma said:
your device not properly CID unlocked...
unlock the device properly with USPL...
Click to expand...
Click to collapse
Sixthsigma...you said - "unlock the device properly with USPL..." - how do I do that?
I got the same error as mentioned when trying to flash using the numb3rs ROM:
http://thewingster.com/numb3rs.aspx
I ran the herald-uspl.exe file. and ended up with teh above error. My TMo Wing has the original ROM on it and the phone itself is probably unlocked. Ive had it for a year now. Do I need to call TMo to unlock or is there some app I can run to do this myself?
appreciate any help!
nevermind, it worked ok on the second attempt!

[tut] how to flash a rom

Since there are many newbies here who are new to the world of flashing I've decided to do them all a huge favor by posting this thread. If there are other tutorials around, I'd suggest the mods sticky them please. I'm going to make this one as user friendly and easy as possible.
Okay. So you're bored of the stock HTC ROM eh? Never fear, the XDA cooks are here
If you are using an XP machine, you are good to go. If you are using Windows Vista or Windows 7, then go to this page and follow the instructions here to roll back the drivers. THIS IS IMPORTANT IF YOU'RE ON VISTA OR 7 BECAUSE OTHERWISE YOUR PHONE WON'T CONNECT IN BOOTLOADER!
Also, take note that while doing ANY kind of flashing, always remove both your SD card and your SIM card. ALWAYS.
Firstly, you will have to CID unlock your phone. Download the USPL and follow the instructions to flash it onto your phone. What, still need instructions? Okay.
Unzip it.
Connect your phone (WHILE IT IS RUNNING, NOT IN BOOTLOADER)
Click start_uspl.exe
Wait till the process finishes.
The phone will automatically reboot. During boot up, you will see a few numbers on your white HTC screen. Look out for the SPL number. If it is 1.11.0000, then you have been successful in unlocking your phone. If not, well, you have to try again. Mostly it should happen in the first go.
Now. Once your phone is CID unlocked, you can download any ROM you want and flash it to your device. Lets say you are kind to me and download one of my ROMs (see my sig )
*Before you flash any ROM though I strongly suggest you update your USPL to the new cmon USPL. This improvement lets you flash ROMs of ANY size to your device. To flash this, just download the file, and replace the ruu_signed.nbh file located in any of my (or anyone else's) ROM package with the one included in cmon USPL.
Then, put your phone into bootloader mode. To do this, switch your phone off. Then press the voice recording, power and reset buttons together. After 5 seconds release the reset button, but keep the other two pressed till you see a three colored screen. Once you see the screen you are in bootloader mode.
Once in bootloader, connect the phone to the PC. Once it is connected run the RUU.exe located in the folder where you just put the cmon USPL .nbh file. Keep pressing next and finally press update. It will be done in 2 seconds. On next boot your SPL version will now say 1.11.cmon. Yay, success.
Now you are ready to flash any ROM of your choice. Download whichever ROM you want, and unzip the package into a folder. The package will have around 6 files. Of them, only RUU.exe and ruu_signed.nbh are important. Once you check for these files, put your phone in bootloader mode again, connect to PC and start RUU.exe. Like cmon USPL, keep pressing next and then update. Soon, you will have a progress bar on your phone as well as your computer screen. The flashing process will be complete in 10 minutes.
The phone will reboot once the flashing is done. Now you can kiss old stock ROM goodbye! On system reboot, the phone will take some time to start, and it will ask you to "tap screen to begin setup". Do as the phone tells you to, align the screen, enter the date and time and your new flashed ROM is ready to use!
I hope this post helps all the newbies out there in flashing their devices. Be warned, you have to be careful while doing this or your device might end up as a very attractive brick. It is very easy and I'm sure all you people can manage it.
Special thanks to:
pof and cmonex for their USPLs
All the brilliant cooks of Artemis XDA
*If I made any mistake in this the experienced people can bring it to my notice and I will make changes. Everything is correct best to my knowledge
Did you mention remove memory card? Also Vista users need to change USB drivers !
Yes, thanks bazzywazz I missed out on thos epoints. First post edited
And on phone usb settings uncheck "enable advanced network function"

[GUIDE]How to Flash Your Vogue (CDMA Only!!!!)

Hi all!!
Ever since I got my Sprint Vogue, I have spent God only knows how many hours looking for and gathering information regarding this phone (flashing instructions, unlocking, SuperCID, etc). There are a few sites that have fairly comprehensive guides as to how to do this, but there are very few posts in the Vogue Section here at XDA-Developers.
Having said that, I figured I would create my own "How to Flash Your Vogue"-Thread. This is a multi-step process and I cannot emphasize the importance of following every step down to the "T", that is unless you are looking for a silicone-skinned brick...
Who is this guide for?
*Anyone with a CDMA version of the Touch. [highlight]That means no GSM[/highlight]
*Noobs and Seniors alike.
*People who have trouble flashing their devices.
*Anyone looking for links to more information.
*Curious people in general.
*Anyone willing to get rid of the nasty stock rom and looking for a newer and cleaner OS (notice that I never said more stable, so do not blame me afterwards ).
[highlight]Please keep in mind that there is always a chance of bricking your device with these procedures. I will not be in any way, shape, or form responsible if you damage your device while doing this.[/highlight]
Got your coffee? Alright, let's do this.
Step 1. Preparing the device
As with every phone, you have to make sure that you have the following things done before flashing:
* Battery charged at least 50%.
* All the necessary programs (see next post).
* Instructions handy.
Make sure that you back up all your information (contacts, e-mails, files).... essentially, anything that you would like to keep post-flashing. You can do this via Active Sync/Mobile Device Center or via third party software (PIM Backup is really good)...
You will have to reinstall every last piece of software in your device as it will be hard reset. Some programs may work if installed in a SD card directly, but a lot of them write things to the registry and copy files to the device, which they require to run. Long story short, keep all your cabs and exe files in a safe place so you can restore later if needed.
Step 2. Unlocking the Device (HardSPL)
Unlocking the device is done so that you can flash custom roms in your devices. The unlocker that you are about to download and use was provided by "ImCoKeMaN" at PPCGeeks. If you are interested in the full thread, please click here.
If you have read the above link, you will see two versions of the HardSPL (0.40 and 2.31). Simply use 2.31 as it works fine with most devices.
[highlight]To use this under Windows XP,[/highlight]
1. Connect your device to your computer and make sure it is synced with ActiveSync.
2. Download and extract the contents of the zip file, which is an exe. Let it run to completion. You will be prompted to disconnect and reconnect your device at one point in the process. Do it... don't worry
3. It will look like it is flashing a rom via a RUU. Do not disconnect the device after it is done!!!!!
4. Once it is done flashing, you will see a prompt that says that it will run exitbl. DO NOT DISCONNECT YOUR DEVICE. At this point, open ActiveSync, go to File>Connection Settings> Uncheck "Allow USB Connections". Continue following the on screen instructions and let it finish.
5. Go to bootloader once more to verify that it worked. You should see 2.31 CoKe MFG.
[highlight]To use this under Windows Vista/7 x64 (thanks jitajt),[/highlight]
jitajt said:
connect your device to WMDC (it's not necessary to set up device, just connect without setting up device)
then right click on the 2.31 unlocker and run as administrator
follow the directions, you will get an error about sleep.exe not being compatible with x64 but just hit ok and continue, (you will get about 10 of them)
then just keep following the directions in the command prompt and it will put your phone into bootloader then you have to disconnect and reconnect when it tells you to. and it will flash your phone and reset it. then your done you can close the command prompt and disconnect your phone.
I did it just like above and I have not had any problems.
Do this at your own risk as I am not responsible for your phone
Click to expand...
Click to collapse
Step 3. Flashing your Roms
The time has finally arrived. You sat down patiently through the unlocker and you are now ready to take the leap of faith into what you believe will bring your device to a new level of usefulness (also known as getting rid of that nasty, bloated, stock rom )
The process is relatively simple:
1. Download the RUU package from this post. I am only posting this because some cooks only post the rom nbh files rather than the whole package.
2. Go into the threads and look for whichever rom you prefer. Look at my signature to learn which one I am using. NFSFan (my current one) is by far the best one I have tried so far. You can download it from here
3. Put your device in bootloader mode and connect the device to the computer. [highlight]Once in bootloader, activesync will NOT see the device. If the RUU gives a connection error, try to run it with the devices in regular mode (with ActiveSync connected)[/highlight]
4. Open the Romupdateutility.exe and follow the steps.
5. Once it is done flashing the rom, disconnect it from the computer and hard reset it. To do this, simply hold "Send" + "End Call" +Stylus in the reset hole for about 3 seconds. It will prompt you to erase all the data and restore to factory defaults. Press "Enter", which is the center button in the directional pad. Once it is done, press "Send" to reboot.
Congratulations, you just flashed your first rom for Vogue
Step 4. SuperCID
This step can be skipped if you are not thinking of doing anything as far as your radio (such as flashing radios other than the ones intended for Vogue). This is also used to do other things such as modifying certain important things on your device such as the NV files, which is information that will not be discussed here. However, if you are interested in finding out more, simply google it, there is a ton of information out there.
Anyways, back to SuperCID... here is the procedure (thanks to hpnasik at mobile-files.com for the post)
1. Download the following special rom . This is an Alltel rom with radio 3.37. This was specially prepared to be able to reduce the Security Level of the device to level zero.
2. Download mtty since you will need it. Do not worry if you do not how to use it. You will have a step by step in this guide.
3. Flash the Alltel rom from above.
Now comes the fun part...
4. Disable USB in Connection Settings of Active Sync
5. Boot The Phone holding power button and camera button to enter bootloader.
6. Phone Will Display Serial in Bottom
7. Connect Phone to PC
8. Phone should Display USB instead of Serial in Bottom
9. start mtty.exe
10. Select All Default and Connect to USB in drop down box and Shoot the Following Commands (All Commands are case Sensitive)
11. run command rtask a : After this Command Phone will not Display any thing
12. run command echo_on : even though nothing is shown to screen
13. run command readCID : in Sprint it will display SPCS_001
14. run command writeCID 00000000 : Set CID Value to 00000000 replaces SPCS_001 in Sprint (This make PPC Radio Security Level to Zero)
15. run command readCID : This will Display the Update CID as 00000000
16. run Command retuoR : This will return to Original Boot Loader State
Congratulations, you just SuperCIDed your device. Original thread with the instructions can be found here if you are interested.
Step 5. Flashing your radio.
Now that your device has been SuperCIDed, you will have the opportunity to flash radios that have been ported to this device (ie. there is a version of the 3.42.40 radio for the Titan, which has been ported to the Vogue). There are two ways of doing this:
Way 1: Do it by flashing via RUU (same as with flashing a rom)
Way 2: Flash via microSD card. Simply put whichever radio that you wish to flash in the root of a 2GB or less microSD card formatted to fat32. Rename the radio to VOGUIMG.NBH and put your device in bootloader. The flashing will start by itself.
Way 3 (I know I said two ways...): There are a few stock roms that come with new radios. One of them can be downloaded directly from HTC and it is for the Sprint Touch. This one comes with Radio 3.42.30
The other one is for Bell Mobility and this one comes with Radio 3.42.50.
Why am I giving "Way 3" if the other two options seem much easier?? I have run into the problem where my device would not let me flash other radios than the one that I had. SD card method did not work and the RUU started out fine but quits at 8% rebooting my phone and displaying Error 328 in the RUU on the PC. Anyway, here are the links...
Sprint rom with radio 3.42.30
Bell rom with radio 3.42.50
Verizon Stock Rom
All Shipped Roms (All Carriers) - Thanks conflipper!
All Above Radios zipped
The newer radios perform a little better and give out better GPS signal (faster locks)....
Hang on a sec... did you just say GPS?!?!? But my Vogue does not have a GPS.... It does, just read a little further and be happy
Step 6. Enabling GPS, Returning to Stock, and Carrier Cabs
As I said before, there is a GPS hidden on your device. Now, if you are like me and went straight to the specs of the phone to confirm, you will probably try to call BS on this. Long story short, there are a few custom roms which have this "tweak" already implemented (like the one I am using from NFSFan). If you require some more info, I will post it later...
[highlight]Location must be on or else your GPS will not work. To activate it, go to Settings>Personal>Phone and change the Location setting to ON instead of 911 (thanks for pointing it out, th3lolz)[/highlight]
[highlight]For Verizon Users[/highlight]
br125 said:
For those of you with the official mr1 update from verizon that cannot get their gps working:
My xv6900 came with the official update and I got it working, it involves downgrading to a NON-GPS radio, then back to a gps radio...
go here: http://forum.xda-developers.com/showthread.php?t=533639
now the instructions are going to imply that you must load the unlocker before each flash... bs don't worry about that
1. flash the .40 unlocker
2. flash the non-gps rom (reset before customization)
3. flash the 2.31 unlocker
4. flash the vzw rom (reset before customization)
5. flash any custom rom or android rom
that's it, time consuming, but it works
*ignore the multiple flashing instructions, its completely unnecessary, I've never flashed more than once with no problem ever....
I also suggest keeping the vzw radio, but do as you will, I like the 3.37.38 radio.. ain't broke don't fix it
lastly, just make sure you RESET BEFORE THE CUSTOMIZATIONS RUN...... that is what locks your gps.
good luck!
ps. the verizon radio rom that is in that post is for the "leaked" 3.37.37 radio, I reccomend using the official update from verizon here for the 3.37.38 radio rom instead:
http://www.pcdphones.com/phone_downloads.aspx?bid=95&cid=1&mid=302&carrier=Verizon Wireless
RESET BEFORE CUSTOMIZATIONS
Click to expand...
Click to collapse
[highlight]How to Relock you phone[/highlight]
If, for whatever reason you need to return your phone for repair/replacement, you will need to relock it. To relock your phone, simply run the unlocker 0.40 and flash the stock rom of your carrier.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker.exe
[highlight]Carrier Cabs[/highlight]
Thanks to Codybear for gathering all of the cabs with settings for various carriers. But since the link went down, here is another one courtesy of LMiller1708
https://sites.google.com/site/vogueroms/vogue-files
This information was only gathered by me and I take no credit whatsoever other than trying to put it in a one stop thread. Thanks to the following people
Shadowmite
ImCoKeMaN
mindfrost
NFSFAN
Codybear
joshkoss
and a bunch of people that were involved in developing all this...
Thread sticky'd as requested
Peace,
Josh
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
dwigginstm said:
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
Click to expand...
Click to collapse
How exciting!! My first victi...erh patient
Did you put the device in bootloader mode? If you did and it is connected to the PC, you should see USB on the screen of your device. Also, do you have ActiveSync on your XP machine? You will need it for the drivers on this step. Changing USB ports sometimes help as well. And one last thing, do not use a USB hub, go directly through the USB ports in your computer. Good luck!
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
yes i have activesync set up with the phone and pc, but when i put the phone in bootloader mode and connect it the pc recognizes it but not activesync. is there another program i can unlock the phone with?
dwigginstm said:
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
Click to expand...
Click to collapse
Do not worry about ActiveSync. While you are in bootloader, the device is not running WM, which is why your computer only sees it as a USB device. This is perfectly fine. ActiveSync will not recognize it.
Please, follow the instructions in my post for unlocking. Read it thoroughly and try to understand it, else you will end up bricking your device.
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
dwigginstm said:
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
Click to expand...
Click to collapse
that is a message in the RUU. do not pay attention to it. good luck...
so i finally got the unlocker to start and it begins the ten minute process and stops then show a 262 error code ive done this over and over again
Let's go from the top. I just saw the message that you were talking about. The unlocker does ask for ActiveSync as you pointed out and it is asking you to connect the device to the computer. Then it asks for you to press any key when that is done. So, try that and you should see the word "initializing" with a dotted line getting longer for about 20 seconds. Do that.
The RUU will start up afterwards. The prompt will tell you that it is going to flash a new SPL, and if I am not mistaken that is where you are getting stuck.
Just out of curiosity, which version of the Vogue do you have? (Alltel, Bell, Verizon, Sprint, US Cellular)?
no internet
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
terrancextc said:
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
Click to expand...
Click to collapse
You downloaded a cab. Simply put it in your SD card and run it by tapping on it. Don't unzip it...
Unlocker is not 64 bit compatible... grrr....

Categories

Resources