Develop Bugs

SD card doesn't click in any more! :(

Right, I recently decided to change the cover on my XDA Exec. Looking back on it, it may be wasn't teh smartest thing in the world to do! My experience of this is that it is very difficult and can definately lead to problems.
I've managed to get it all back together again, with only two problems, firstly the flash on the camera doesnt work - not too much of a concern. And secondly the SD card slot doesnt work - a big concern.
When I insert the SD card it just springs straight back out, and doesnt click in like it used to. I wonder if any one else has had a similar experience to mine, and knows how to fix it? I've looked at a few sites on google and some suggest that the locking mechanism on the left hand side may be stuck. Without seeing with the mechanism looked like before I took it apart I have no clue as to what has changed.
Can anyone help??
Many thanks.

As far as the SD card goes, there is a little spring on the mechanism which sometimes pops off. Just a case of carefully opening the case and seeing if you can pop the spring back onto it's hook. While you're in there you can check if the flashlight is still attached properly.
In case you need them, here are the instructions to open the case:
ftp://xda:[email protected]/UNniversalL_Service_Manual_CONFIDENTIAL.pdf

o2 Orbit (Atermis) MicroSD woes

Hi All,
My micro SD slot seems to be broken (
Does anyone know how to fix these? I think one of the lugs that holds the metal cage on has snapped - quite how, I dont know. It means it is only held on in 3 sides
This means that it isnt recognising any SD card I put in it - which sort of kills the whole idea of the phone for me... 64mb isnt enough!
Thanks in advance for any ideas

What's with the weird SD card slot design?

Anyone know why HTC decided to go with that really weird design for the SD card? It's such a pain in the Ass =( why not just a normal slot.

I imagine that to help make the phone thinner they brought it to the inside. I also imagine they figure that with 32gb cards getting cheaper, more and more people will just "set it and forget it." All this is purely speculation though.
Sent from my HTC Vision using XDA App

I really wish the SD card was more accessible. If it was a spring loaded slot feed on the side of the phone, for example.
It would be nice to swap cards and have one card for "ipod mode", one with some movies or tv shows and one for general use, for example.
Even having to pop the battery cover would be OK, but having to remove the battery is a showstopper.

dadewy said:
I really wish the SD card was more accessible. If it was a spring loaded slot feed on the side of the phone, for example.
It would be nice to swap cards and have one card for "ipod mode", one with some movies or tv shows and one for general use, for example.
Even having to pop the battery cover would be OK, but having to remove the battery is a showstopper.
Click to expand...
Click to collapse
AGREED
Sent from my HTC Vision using XDA App

Maybe the required removal of the battery thing is to make sure that you don't eject the SDCard while writing to it/reading from it or anything like that.
I dunno.
I'd love a more accessible design too.

catachresistant said:
Maybe the required removal of the battery thing is to make sure that you don't eject the SDCard while writing to it/reading from it or anything like that.
I dunno.
I'd love a more accessible design too.
Click to expand...
Click to collapse
I thought of that too... ideally, we could have the device sense when the battery cover is off and umount the sdcard at that point.
The question remains what to do if the sdcard is busy at the time. I guess the same problem exists when attaching the usb cord in "drive" mode, and that seems to work OK, so do whatever it does
Oh well, nice to speculate but we're stuck with the current (crap) design.
Hmm or are we? Flex ribbon cable to make the sdcard external anyone? I can't think of an elegant way to do this, unfortunately, there's no room between the battery and battery cover, that's for sure.

[Q] DInc2 uSD card removal

How do I remove the card from the phone to replace it? Seems like the text "microSD" is getting in the way of the card sliding out from the slot. Is there some trick that I should know? (First phone that I've not been able to switch cards with).
Thanks in advance for not laughing at me. I realize this should be easy, but the card doesn't have a push-remove feature and extracting it by gently pulling at the "lip" isn't working either.

That's strange, if I push mine in, it will pop right out. Don't know what to tell you. Maybe something else has gotten lodged in to the slot with the sd card?

I know the first time I tried to pull my SD card out, I had a really difficult time getting it out, after pushing it in.
Sent from my HTC Incredible 2 using XDA App

Is it the 16gb that came with the DIncII?
One of my smaller (2gb) cards has a "label" that covers some contacts near the griping area of the card.
No idea why that isn't just a thin layer of some form of epoxy like other cards.
I just use it in an adapter with my Cannon camera.
When you finally get it out of there, if it's not the one that came with the phone then look for a label to remove and put a VERY thin coat of nail polish (clear) over anything that might need it.
Careful not to get any on the data contacts.
And be sure to let it dry for a long time before you put it back in.
Better yet, unless it's the only card you will ever own, get a new one.
Most of these cards have a lifetime warranty.
If it's the one that came with your phone, get on with VZW and have them send a new one.
If the card you are using has no catch tab, then you should NOT put it in this type of device.
It was made for a camera or something that uses an adapter that does NOT have a catch mechanism.
Like the old pushbutton radios that you could pull the button to preset the station, but if you push more than one button at one time you could snap the string.
The catch lock may have locked against the area of the card where the tab should be.
And as stated check the slot for things in there that should NOT be in there.
Like the broken off tab from a card that was pulled out.
Or an eyelash would even mess things up.
Anytime I remove my card I allays "puff n spit" (suck like taking a toke and spit AWAY from the device) before and after removal.
No telling what might have crawled around the slot.
The worst thing to do is to blow things INTO the slot.
Hope that helps..

Sim card tray damaged. Best way to fix?

I have a tendency to hop back and forth between phones. Today I went to put my sim card in my Note 2. I use a nano sim card adaptor (I decided to experiment with the iPhone 5 for about a month...) to put my sim card in my Note 2 and my Nexus 4. Unfortunately, the sim card fell out while I was putting it in my Note 2 today and the adaptor got stuck in the tray. After a few moments of agonizing struggle, I got the adapter out. Now my Note 2 won't recognize my sim card. I think the prongs at the entrance of the slot were damaged, since that's where the adaptor kept getting hung up.
Is there a way to find out if it's completely broken or if the prongs are just out of place? And if it's broken, does anyone know how much a repair would cost? I don't know that I have the confidence to try to repair it myself.
Thanks.
Sent from my Nexus 4 using Tapatalk 2

The SIM card reader module I'm fairly certain is soldered onto the logic board, so unless your good with soldering, a replacement SIM reader isnt very practical. However, the Sprint Epic Touch (GS2) sd card reader module is attached only by a simple flex cable, so its possible the same may apply here. If this were the case, the replacement part shouldnt cost more than 10-20$ (assuming their available) and replacement would be as hard as taking the back housing off.
Try comparing the SIM slot with another similar model and see if you can see if something is out of place. See see see see see see.:good:

I think I may have done the same to mine with one of those SIM adapters. I've ordered this and it should be here in a few days. I'll give it a go...
http://www.ebay.com/itm/OEM-Samsung...271792?pt=PDA_Accessories&hash=item1c313e9ef0

u did the same exact thing i did lol but what i thought was a damaged sim tray was somehow just corruted firmware when i restored back to stock everything worked just fine i even called samsung and they were going to replace it but since i live in Hawaii i didnt want to wait so i just did a restore in odin and everything works fine
if u are really damaged ur stim tray and dont wanna wait on samsung u can try this
http://www.youtube.com/watch?v=UT-2zrZ_aNo
but good luck try restoring with odin first

I'm glad I'm not the only one to have had this problem, heh heh.
Anyway, after watching the video, I think I'm going to send my Note to Samsung and have them fix it. I would probably ruin my phone if I did it myself. Should I do a factory reset to protect my data before doing so? I don't know if they'll be sending the same phone back to me, since it says they may replace it with another if they determine that they aren't going to fix the part that's broken.

blackplague1347 said:
I'm glad I'm not the only one to have had this problem, heh heh.
Anyway, after watching the video, I think I'm going to send my Note to Samsung and have them fix it. I would probably ruin my phone if I did it myself. Should I do a factory reset to protect my data before doing so? I don't know if they'll be sending the same phone back to me, since it says they may replace it with another if they determine that they aren't going to fix the part that's broken.
Click to expand...
Click to collapse
they will wipe ur data if ur rooted and have a custom rom on your phone u need to return to stock and set the flash counter to zero.
u would send the phone is no battery no battery cover no sim card so sd card just the phone nothing else
try to restore ur phone via odin first
http://galaxynote2root.com/galaxy-n...ootunbrick-galaxy-note-2-with-stock-firmware/
if u still get no sim card error after doing that then give samsung a call phone number is on the phone itself under battery and they will send u a box and u should have to wait about 2 weeks then u will either get a fixed phones or a replacement not sure how they do it since i fixed my no sim issue with odin

I did the same thing once. Just called att and told them it wasn't reading a simple anymore and they sent me a new one.
Sent from my GT-N7105 using Tapatalk 2

My Fix For Broken SIM Reader Pin
This is an old thread, I know. But the problem is ongoing. These SIM card adapters are just plain evil. Now that this has happened to me, I googled the issue and see that there are tons of folks suffering. I am posting this reply so that others can see the "fix" I managed for my International Samsung Note I. I am sure it can be applied to most other phones.
I should point out that in order to get any usable access to and visibility of the SIM card reader I had to remove the battery cover and the back from the phone's touchscreen. This reveals the motherboard to which the SIM card reader is soldered. I found a good video on this at YouTube. It wasn't that hard although I did not have the plastic pry bar they used - I think I will get one for the future. I managed with a small flat head jewelers screw driver and an ancient, plastic shirt collar stay. (I can hear my mother saying "save it - you'll find a use for it!" I hate it when she is right.) Once complete I could move on.
At first, I tried to replace the SIM card reader pin that was broken off by the SIM card adapter with a tiny piece or rolled-up tin foil. I saw someone else reference this approach and it seemed possible and cheap. Alas, it did not work. After many attempts, the phone simply would not recognize any SIM card. I finally got to sleep at 3am.
I then found a piece of brass shim stock that I have had lying around for years. (I am hearing mom again!) It is item 1412110231, Brass Strip .016x1/2inx12in shown here. I got mine at the local hardware store for some other aborted project. I used some snips to cut off a tiny strip from one end and then cut that strip to maybe 1/3 to 1/2 its overall length. The idea was to place the strip inside the SIM reader slot where the pin had broken off in an effort to create a contact point to replace the pin. Cutting the tiny strip off the stock piece caused the tiny strip to bow a bit. It turns out that was a good thing but I had to reduce the amount of bow quite a bit for it to fit inside the reader. Remove any rough edges from the tiny strip with a file.
With the touchscreen assembly lying flat on the table I managed to get the tiny strip in place. I was then able to slowly and carefully slide the SIM card into the reader and this resulted in a contact good enough to make the phone again recognize the SIM card and for cell service to be restored. Hurray! Yes, I was able to carefully place the battery in its bay and operate the power button to perform testing.
But you must remain aware that the tiny strip is just lying in the slot and is held in place only by friction/pressure from the SIM card inserted into the reader. Therefore, for the rest of the phone's life, it requires great care when removing the SIM and handling the phone when a SIM is not installed . Basically when removing the SIM, the phone MUST remain flat on its display until the SIM is re-installed. Moving the phone around in other orientations without a SIM card installed will definitely cause the tiny strip fall out. And who knows what hell that will cause?
You cannot put the phone's back onto the touchscreen with the SIM card in place. At first I thought about cutting the SIM's length down so the back would install even with the SIM in place. Before doing this I tried to carefully snap the top portion of the back onto the touchscreen while it all remained flat on the table so the tiny strip wouldn't move. With the top 1/3 of the back snapped on, I could just manage to insert the SIM through the phone's cover and have the tiny strip held in place by the SIM while I snapped the rest of the back into position. This worked pretty well but your mileage may vary.
I basically plan to leave the SIM in place forever - even if it is not to be used. I also put a reminder note on the battery so that I am less likely to forget that I made this hack.
I hope the annotated photos help those who follow me - as surely others will do. Good luck. I was very lucky to have destroyed only one pin and for it to be in the most accessible part of the SIM reader.