How do I remove the card from the phone to replace it? Seems like the text "microSD" is getting in the way of the card sliding out from the slot. Is there some trick that I should know? (First phone that I've not been able to switch cards with).
Thanks in advance for not laughing at me. I realize this should be easy, but the card doesn't have a push-remove feature and extracting it by gently pulling at the "lip" isn't working either.
That's strange, if I push mine in, it will pop right out. Don't know what to tell you. Maybe something else has gotten lodged in to the slot with the sd card?
I know the first time I tried to pull my SD card out, I had a really difficult time getting it out, after pushing it in.
Sent from my HTC Incredible 2 using XDA App
Is it the 16gb that came with the DIncII?
One of my smaller (2gb) cards has a "label" that covers some contacts near the griping area of the card.
No idea why that isn't just a thin layer of some form of epoxy like other cards.
I just use it in an adapter with my Cannon camera.
When you finally get it out of there, if it's not the one that came with the phone then look for a label to remove and put a VERY thin coat of nail polish (clear) over anything that might need it.
Careful not to get any on the data contacts.
And be sure to let it dry for a long time before you put it back in.
Better yet, unless it's the only card you will ever own, get a new one.
Most of these cards have a lifetime warranty.
If it's the one that came with your phone, get on with VZW and have them send a new one.
If the card you are using has no catch tab, then you should NOT put it in this type of device.
It was made for a camera or something that uses an adapter that does NOT have a catch mechanism.
Like the old pushbutton radios that you could pull the button to preset the station, but if you push more than one button at one time you could snap the string.
The catch lock may have locked against the area of the card where the tab should be.
And as stated check the slot for things in there that should NOT be in there.
Like the broken off tab from a card that was pulled out.
Or an eyelash would even mess things up.
Anytime I remove my card I allays "puff n spit" (suck like taking a toke and spit AWAY from the device) before and after removal.
No telling what might have crawled around the slot.
The worst thing to do is to blow things INTO the slot.
Hope that helps..
Related
Bit of a weird question, but I recently bought a Desire with serial number HT09 and the micro-sd slot was just an interference fit, and I had to pick the card out with my nail.
This phone has just been replaced due to rebooting issues and the new phone I received from t-mobile has s/n HT08. This phone has a spring loaded micro-sd slot, so I just have to push the card in to eject it.
This to me seems like better attention to detail, I just wonder why they changed it?
Was it maybe made in a different factory?
Cheers, Rich.
the first few weeks I had mine (HT05) I was picking the card out with my finger nail but then the spring 'sprung' into life and now I push down to remove it, so I can only guess that they all have springs fitted and that some work properly and some dont
The HT04 lot are fine.... cant see thay would take the spring away ... it's still very fidderly to get the card out... far too small !!!!!!!
Well, I have a micro SIM from T-Mobile which I was using in my lumia. I wanted to see if I could find a way to make it fit in a regular SIM slot. I decided to try making an extender out of a gift card. When I put it in, it didn't fit. I pulled, and pulled with tweezers, my hands, etc. All failed, and eventually the little piece I was pulling, broke off. I then had a piece of the gift card stuck deep in the slot. So stupidly, I decided to dig around in the SIM slot with the edge of the tweezers to pull it out. Now I can't put a SIM in the SIM slot, and there's still gift card in there. I may have damaged the SIM reader prongs as well... Any ideas on how to fix it? Can I pull off the actual back part to get to it? I really hope I'm not ultimately screwed...
Sent from my HTC Vision using XDA
take apart your phone and have a look see, at the very least you should be able to get out the giftcard piece. if you didnt cause too much damage it probably will be fine once out
I have a tendency to hop back and forth between phones. Today I went to put my sim card in my Note 2. I use a nano sim card adaptor (I decided to experiment with the iPhone 5 for about a month...) to put my sim card in my Note 2 and my Nexus 4. Unfortunately, the sim card fell out while I was putting it in my Note 2 today and the adaptor got stuck in the tray. After a few moments of agonizing struggle, I got the adapter out. Now my Note 2 won't recognize my sim card. I think the prongs at the entrance of the slot were damaged, since that's where the adaptor kept getting hung up.
Is there a way to find out if it's completely broken or if the prongs are just out of place? And if it's broken, does anyone know how much a repair would cost? I don't know that I have the confidence to try to repair it myself.
Thanks.
Sent from my Nexus 4 using Tapatalk 2
The SIM card reader module I'm fairly certain is soldered onto the logic board, so unless your good with soldering, a replacement SIM reader isnt very practical. However, the Sprint Epic Touch (GS2) sd card reader module is attached only by a simple flex cable, so its possible the same may apply here. If this were the case, the replacement part shouldnt cost more than 10-20$ (assuming their available) and replacement would be as hard as taking the back housing off.
Try comparing the SIM slot with another similar model and see if you can see if something is out of place. See see see see see see.:good:
I think I may have done the same to mine with one of those SIM adapters. I've ordered this and it should be here in a few days. I'll give it a go...
http://www.ebay.com/itm/OEM-Samsung...271792?pt=PDA_Accessories&hash=item1c313e9ef0
u did the same exact thing i did lol but what i thought was a damaged sim tray was somehow just corruted firmware when i restored back to stock everything worked just fine i even called samsung and they were going to replace it but since i live in Hawaii i didnt want to wait so i just did a restore in odin and everything works fine
if u are really damaged ur stim tray and dont wanna wait on samsung u can try this
http://www.youtube.com/watch?v=UT-2zrZ_aNo
but good luck try restoring with odin first
I'm glad I'm not the only one to have had this problem, heh heh.
Anyway, after watching the video, I think I'm going to send my Note to Samsung and have them fix it. I would probably ruin my phone if I did it myself. Should I do a factory reset to protect my data before doing so? I don't know if they'll be sending the same phone back to me, since it says they may replace it with another if they determine that they aren't going to fix the part that's broken.
blackplague1347 said:
I'm glad I'm not the only one to have had this problem, heh heh.
Anyway, after watching the video, I think I'm going to send my Note to Samsung and have them fix it. I would probably ruin my phone if I did it myself. Should I do a factory reset to protect my data before doing so? I don't know if they'll be sending the same phone back to me, since it says they may replace it with another if they determine that they aren't going to fix the part that's broken.
Click to expand...
Click to collapse
they will wipe ur data if ur rooted and have a custom rom on your phone u need to return to stock and set the flash counter to zero.
u would send the phone is no battery no battery cover no sim card so sd card just the phone nothing else
try to restore ur phone via odin first
http://galaxynote2root.com/galaxy-n...ootunbrick-galaxy-note-2-with-stock-firmware/
if u still get no sim card error after doing that then give samsung a call phone number is on the phone itself under battery and they will send u a box and u should have to wait about 2 weeks then u will either get a fixed phones or a replacement not sure how they do it since i fixed my no sim issue with odin
I did the same thing once. Just called att and told them it wasn't reading a simple anymore and they sent me a new one.
Sent from my GT-N7105 using Tapatalk 2
My Fix For Broken SIM Reader Pin
This is an old thread, I know. But the problem is ongoing. These SIM card adapters are just plain evil. Now that this has happened to me, I googled the issue and see that there are tons of folks suffering. I am posting this reply so that others can see the "fix" I managed for my International Samsung Note I. I am sure it can be applied to most other phones.
I should point out that in order to get any usable access to and visibility of the SIM card reader I had to remove the battery cover and the back from the phone's touchscreen. This reveals the motherboard to which the SIM card reader is soldered. I found a good video on this at YouTube. It wasn't that hard although I did not have the plastic pry bar they used - I think I will get one for the future. I managed with a small flat head jewelers screw driver and an ancient, plastic shirt collar stay. (I can hear my mother saying "save it - you'll find a use for it!" I hate it when she is right.) Once complete I could move on.
At first, I tried to replace the SIM card reader pin that was broken off by the SIM card adapter with a tiny piece or rolled-up tin foil. I saw someone else reference this approach and it seemed possible and cheap. Alas, it did not work. After many attempts, the phone simply would not recognize any SIM card. I finally got to sleep at 3am.
I then found a piece of brass shim stock that I have had lying around for years. (I am hearing mom again!) It is item 1412110231, Brass Strip .016x1/2inx12in shown here. I got mine at the local hardware store for some other aborted project. I used some snips to cut off a tiny strip from one end and then cut that strip to maybe 1/3 to 1/2 its overall length. The idea was to place the strip inside the SIM reader slot where the pin had broken off in an effort to create a contact point to replace the pin. Cutting the tiny strip off the stock piece caused the tiny strip to bow a bit. It turns out that was a good thing but I had to reduce the amount of bow quite a bit for it to fit inside the reader. Remove any rough edges from the tiny strip with a file.
With the touchscreen assembly lying flat on the table I managed to get the tiny strip in place. I was then able to slowly and carefully slide the SIM card into the reader and this resulted in a contact good enough to make the phone again recognize the SIM card and for cell service to be restored. Hurray! Yes, I was able to carefully place the battery in its bay and operate the power button to perform testing.
But you must remain aware that the tiny strip is just lying in the slot and is held in place only by friction/pressure from the SIM card inserted into the reader. Therefore, for the rest of the phone's life, it requires great care when removing the SIM and handling the phone when a SIM is not installed . Basically when removing the SIM, the phone MUST remain flat on its display until the SIM is re-installed. Moving the phone around in other orientations without a SIM card installed will definitely cause the tiny strip fall out. And who knows what hell that will cause?
You cannot put the phone's back onto the touchscreen with the SIM card in place. At first I thought about cutting the SIM's length down so the back would install even with the SIM in place. Before doing this I tried to carefully snap the top portion of the back onto the touchscreen while it all remained flat on the table so the tiny strip wouldn't move. With the top 1/3 of the back snapped on, I could just manage to insert the SIM through the phone's cover and have the tiny strip held in place by the SIM while I snapped the rest of the back into position. This worked pretty well but your mileage may vary.
I basically plan to leave the SIM in place forever - even if it is not to be used. I also put a reminder note on the battery so that I am less likely to forget that I made this hack.
I hope the annotated photos help those who follow me - as surely others will do. Good luck. I was very lucky to have destroyed only one pin and for it to be in the most accessible part of the SIM reader.
For those that have the Tab Pro 8.4, is the micro SD slot supposed to be spring loaded? Is it supposed to lock in place when you push it in?
On my tablet right now when I insert my micro SD card, I can't keep it in. It keeps protruding oit. Do I have a defective micro SD slot?
Probably, here it works perfectly...
Sorry man
Yeah, sounds like it may be defective.
Behaves the same as the tray on other devices: push the card in, and it will stay in (I think the card should be about flush with the surrounding plastic - I don't have my Tab with me right now, but I just popped out/in the card the other day). Push the card again, and it will "spring" slightly so that its sticking out by a few millimeters, so you can grab it and take it out.
dapperwix said:
For those that have the Tab Pro 8.4, is the micro SD slot supposed to be spring loaded? Is it supposed to lock in place when you push it in?
On my tablet right now when I insert my micro SD card, I can't keep it in. It keeps protruding oit. Do I have a defective micro SD slot?
Click to expand...
Click to collapse
Yes it is spring loaded, but to get the card to seat and lock in place properly I had to push it pretty far in (carefully) with a long finger nail.
The slot is quite deep set and pushing the card in flush with the case wasn't enough to get it to lock in place and it kept popping back out - a bit of hassle compared to my other devices with micro SD to be honest.
Oh sorry, I had misunderstood your question.
Indeed you have to pull it really far, my nails barely can do it, so generally I use the SD adaptor to push it further untill it locks...
hundred_miles_high said:
Yes it is spring loaded, but to get the card to seat and lock in place properly I had to push it pretty far in (carefully) with a long finger nail.
The slot is quite deep set and pushing the card in flush with the case wasn't enough to get it to lock in place and it kept popping back out - a bit of hassle compared to my other devices with micro SD to be honest.
Click to expand...
Click to collapse
That is true, I was thinking you have to push the card in farther then flush (I think it "clicks" a bit) in order to lock it in the "inserted position". Then push it again to eject it. I just couldn't remember for sure, since I don't have the device with me at the moment.
Very true, that the slot is set a bit too deep. So I have a little difficulty pressing the card in, to eject it. So the same can certainly be true when pushing the card in to "lock" it in place. I would follow the above suggestions to push the card (gently and carefully) with some thin object, as far as it will go. And if it still doesn't lock in place, the locking mechanism may be broken. I can do it with just my fingernails (they are usually short) but it often takes a couple tries to get it to eject. I don't usually have issues inserting it, but I can see how the same would still apply.
Thanks for all the input. Yeah. I can't get the card to lock in place when I push it in, and I am pushing it in pretty far. I'm thinking the spring mechanism may be defective, but sounds like you may have to push in far I will try again later tonight.
Pretty late to the party here, but since I didn't see it mentioned, you should know that the card inserts face-up, meaning the contacts on the card face the back of the tablet.
And yes, it's very deep, but is spring loaded.
As the title says, my S3 will no longer hold the SIM card. The spring just keeps popping the SIM card back out.
Does anyone know how I could play a bit of operation to just disable the spring?
I just want to get a few more weeks out of my s3 until the new nexus 5
arasarn said:
As the title says, my S3 will no longer hold the SIM card. The spring just keeps popping the SIM card back out.
Does anyone know how I could play a bit of operation to just disable the spring?
I just want to get a few more weeks out of my s3 until the new nexus 5
Click to expand...
Click to collapse
I had a phone where the microSD slot stopped working right. A piece of business card trimmed to the right size to slip into the tray along with the SD card added just enough tension to hold the SD card in place without becoming hopelessly wedged. Something similar might work for this if you can find the right thickness card. Good luck.
jason2678 said:
I had a phone where the microSD slot stopped working right. A piece of business card trimmed to the right size to slip into the tray along with the SD card added just enough tension to hold the SD card in place without becoming hopelessly wedged. Something similar might work for this if you can find the right thickness card. Good luck.
Click to expand...
Click to collapse
I wound up electrical taping it into place.
Hopefully that holds for a while...
Nope. That worked for about five minutes. Back to the drawing board.
I folded up a piece of tape and used it with more tape, to jam everything in tight together. Seams to have lasted ten minutes now.
I had the same problem and did this.
Samsung Galaxy S3 I747- (AT&T) SIM Card/ Micro SD Memory Card Slot Holder Flex Cable Replacement Kit
Sent from my SAMSUNG-SGH-I747 using Tapatalk
arasarn said:
As the title says, my S3 will no longer hold the SIM card. The spring just keeps popping the SIM card back out.
Does anyone know how I could play a bit of operation to just disable the spring?
I just want to get a few more weeks out of my s3 until the new nexus 5
Click to expand...
Click to collapse
For anyone that comes across this in the future (or if you still need a solution):
At the bottom of the SD card slot (while holding the phone upright) there is a small spring which is responsible for pushing the card out. You can pull the spring out with a small phillips screw driver, knife or other thin point.
At the bottom right of the SD card slot there is a small tab like feature. Bend this up, and put your screw driver downwards into this small hole. Now pry the spring out. It will take a few attempts, and it will definitely help if you use a flashlight and look to see whats going on in there.