Develop Bugs

diamond won't upgrade to 1.93 hspl

I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??

paulmurphy777 said:
I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??
Click to expand...
Click to collapse
...unfortunately no ideas, just the same problem described here already: http://forum.xda-developers.com/showthread.php?p=2927161#post2927161

paulmurphy777 said:
I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??
Click to expand...
Click to collapse
I have the exact same issue... I tired updating it from 1.24 to 1.93 and it restarted like it updated it. But when I go into boot loader its still got the old hardspl.
Does anyone know why??
I have tried searching around for a solution but no luck

I'm no noob and i've flashed 100's of times across many fones and unbricked a few with some careful reading but this seems very odd and stupidly simple. No idea what i'm missing.... only thing i can think to try is to flash from internal storage, but i would think this unwise with the hardspl as I thought hardspl would control access to the internal storage like some sort of bios perhaps?!

Same here
Hey guys,
Does anyone knows what is the resolution for this? I having the same problem as well.

Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris

gladiac said:
Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris
Click to expand...
Click to collapse
i have almost same problem but the only difference that my Diamond don't have hardspl on it and whenever i try to flash any hardspl phone stops at 0% and stays there for a long time....I want to change my Diamonds language...So can anyone suggest me solution.....I have already posted here on forum but no answer yet!
http://forum.xda-developers.com/showthread.php?t=749664
Another little question that how i can flash hardspl via internal storage and where its root???Root is the device path which we seen as drive in computer when we use mass storage or any other?

gladiac said:
Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris
Click to expand...
Click to collapse
Thank you. used this and it worked

Hi everybody,
got yesterday another diamond, after mine died some time ago. It has 193 spl and I cannot upgrade to olinex spl. It runs through everything, but upon reboot it still has the original 193 spl. Any ideas? I really need to flash, mine speaks Dutch and I want it in English. Please help. Kind regards. Ben

US Diamond (pregame)

Hello XDA Friends!
I have done 2 solid nights of reading now - not to say I am in the least bit an expert, but this is my second experience with flashing htc phones (previously had a htc wizard). I am not a complete newb, but I have a few unanswered questions before i jump in balls deep.
1) After searching the forums, I have found that I seem to have a (rare) ROM version - 1.93.422.4 WWE to be exact. It is the stock US 3G GSM ROM. It appears that others have (after hardSPL) successfully flashed their Diamonds accordingly with European versions. I went to HTC's website and registered my Diamond and they told me that they do not have a down-loadable version of their ROM (an official HTC ROM) for the 3G US version. HTC simply does not make a version for US 3G that they release.
-"Unfortunately, after some checking on our website with your serial numbers, we have found that currently there is no ROM update for your devices. From our experience, there is almost never an update developed for unlocked US GSM devices. The way we release our updates is we develop them first (after receiving the operating system from Microsoft). Then the carrier or vendor takes the update and modifies it to fit their policies and we release it. Unfortunately, the vendor that usually sells unlocked US devices does not complete the last step." -HTC
This concerns me as this is my fallback in the event things do not go so well for me while flashing. SOOOO all that said, does anyone have a copy of the ROM lying around for my backup benefit!?!
2) Can anyone with a US diamond verify that they are indeed running with a cooked ROM (and be so kind as to suggest which one they prefer?). Obviously its trial and error, but stability and speed are high on the priority list (stock is SOOOO SLOOOW)!
3) The hard reset is confusing me. HTC rep said that if i do a hard reset that it will restore the device to factory settings, thus no need for me to download a ROM to restore the device (i obviously did not tell him i was looking into cooked ROMS!).
-" As far as a ROM that would restore the device, you would simply need to do a hard reset in the even that the ROM became corrupt. This would restore the device to factory defaults. " - HTC
This would indicate that the ROM is somewhere on the internal 4gb storage and copies itself back to the ROM. Is this erased when upgrading ROMS or becomes unavailable after going to hardspl? or would i still have the option to hard reset (take the red pill) and wake up believing that my dance with cooked ROMS was a dream!?!?
Thanks for all your help - fire away - I have thick skin. I'm sure someone will point out my lack of research skills ;p
Long live Xda,
-Nate

I have an unlocked US GSM also. I also tried to get it off the site and it said it was not for my device...
HTC support is pretty much useless, I called and they told me over the phone that my phone wont run WWE roms and that i needed US roms and i told them thats funny because it came preloaded with 1.93WWE.
Anyways The New official rom will work on your phone and its allot faster than the 1.93
First the Hard SPL i used this.
I use this RUU_Signed_1_93OliNex_HSPL_UnsignedEdition
http://forum.xda-developers.com/showthread.php?t=400950
And if you want the official 2.03 WWE ROM its here
Want this one
RUU_Diamond_HTC_WWE_2.03.405.2_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship
http://forum.xda-developers.com/showthread.php?t=471699
I haven't used any cooked ROMS yet so i cant help you out there

Awesome - thanks for the info - that was exactly what i was looking for! Yea... the fact that it says WWE in the ROM is completely contradicting - HTC tech support doesn't seem to know whats going on.
Have you tried the hard reset since you loaded the new ROMs? does it revert to 1.93?
Thanks again for posting,
-Nate

ok all,
flashed to hardSPL olinex 1.40, confirmed in the bootloader, tried to flash to 2.03WWE (as referred to me from above) and it gives me:
Error [244] : invalid model ID
This update utility cannot be used for your pda phone. please check your update utility.
OK. from reading i gather this is because something is wrong with hardSPL? what hardSPL should i use? Or is it another issue entirely?
thanks,
-Nate
btw - after hardSPL, and hard reset, everything on the internal storage is there

perhaps i need to be more specific. When i enter the bootloader, it says:
DIAM100 MFG 64M
SPL-1.40.OliNex
what the bible says it should say is
Hard SPL 1.40.Olinex
DIAM100 MFG 64M
SPL-1.40.OliNex
Does this mean that it did not upgrade correctly? Any ideas? Im trying win 1.37 OliNex
again it says in the bootloader
DIAM100 MFG 64M
SPL-1.37.OliNex
lets me get all the way to 99% and then fails with
Error 270 :update error
The image file is corrupt. please check your update utility.
I need some help guys. Starting to get a little frustrated do you have to update the radio rom before it will take the main rom?
-Nate
Ok, next update. Could not get any of the olix hard SPLs to work. I have tried to upgrade to hardSPL 1.24 per this thread
http://forum.xda-developers.com/showthread.php?t=408621
only problem is that the phone does not ever boot into windows. When i go into the bootloader, it still shows olix 1.37 hard SPL. I have tried re-downloading the file. So far it gets to 100% of the ROM flash and then throws the error 270. Any thoughts?

I never had this problem but on the page were you got the ROM they say if your having issues installing through the update utility to do this.
Rename ..NBH file to DIAMIMG.nbh
Copy to Internal Storage
Soft Reset + Hold volume down button + back button <--
Follow instructions on screen
Anymore problems just read this through the thread were you got the ROM your not the only one who got the "corrupted 270 error".
But flashing it from the storage card should work . ..Goodluck
http://forum.xda-developers.com/showthread.php?t=471699

Ok all,
I have had a hell of a time getting a rom that will install. I could repeatedly get to the bootloader without a problem, and every rom i flashed after installing olinex 1.37 allowed me to get all the way to 100% but would then tell me that the rom was corrupt.
I downloaded and installed Shaks rom, version 3.20 from
http://diamond.geg0r.de/index.php?dir=Shaks/V3.20/
AND ITS BACK INTO WINDOWS!!!!!! thanks GOD!
I will report on further issues i have with the device.
-Nate

When I try to burn the 2.03 WWE ROM mentioned onto my stock US Diamond I get: Error 294: Invalid Vendor ID.
Any ideas what I need to do? I did not change the SPL - must I do that?
I read through the referenced threads and see where people with Error 270 need to put the image file onto internal storage but I have been hesitant to try that since it for Error 270 and not necessarily Error 294.
Any ideas?
Thanks!

wpsantennas said:
When I try to burn the 2.03 WWE ROM mentioned onto my stock US Diamond I get: Error 294: Invalid Vendor ID.
Any ideas what I need to do? I did not change the SPL - must I do that?
I read through the referenced threads and see where people with Error 270 need to put the image file onto internal storage but I have been hesitant to try that since it for Error 270 and not necessarily Error 294.
Any ideas?
Thanks!
Click to expand...
Click to collapse
You need to upgrade to HardSPL.

demo23019 said:
I never had this problem but on the page were you got the ROM they say if your having issues installing through the update utility to do this.
Rename ..NBH file to DIAMIMG.nbh
Copy to Internal Storage
Soft Reset + Hold volume down button + back button <--
Follow instructions on screen
Anymore problems just read this through the thread were you got the ROM your not the only one who got the "corrupted 270 error".
But flashing it from the storage card should work . ..Goodluck
http://forum.xda-developers.com/showthread.php?t=471699
Click to expand...
Click to collapse
Here is the Rom only if anybody wants to flash it. You will not get the invalid ID error.
http://www.sendspace.com/file/iesg1h

Thanks for everybody's help. Burning the new SPL did the trick.
Have tweaked everything pretty much back to how I like it and am quite happy with the new ROM. My only complaint is that I prefer the larger Compact QWERTY keypad of the 1.93 ROM since I have fat fingers. I know that I can dig that keypad up elsewhere but I'll try to get used to the new one first.
Thanks again.

Is there USPL for htc diamond?

I've been reading and I see there's uspl for devices, for upgrading a rom without the need to upgrade to hard spl,
Is there uspl for htc diamond? Is it more dangerous for use?
Im asking because everything I found is related to hspl only.
I need to keep the option for restoring everything back for warrenty reasons, but I see its not possible to flash back to stock spl from internal storage, so I'm afraid one day maybe my usb slot will stop function and I wont be able to flash it using AS.
It may sound dumb, I know, but I want to make it carefully.
Is there any risks involved in using uspl instead of hspl?
I appreciate the help.
Thanks in advance.
Edit: I did found SSPL, though only for very old versions of radio and rom, Mine is 1.93 and radio 1.00.25.05

eranyanay said:
I've been reading and I see there's uspl for devices, for upgrading a rom without the need to upgrade to hard spl,
Is there uspl for htc diamond? Is it more dangerous for use?
Im asking because everything I found is related to hspl only.
I need to keep the option for restoring everything back for warrenty reasons, but I see its not possible to flash back to stock spl from internal storage, so I'm afraid one day maybe my usb slot will stop function and I wont be able to flash it using AS.
It may sound dumb, I know, but I want to make it carefully.
Is there any risks involved in using uspl instead of hspl?
I appreciate the help.
Thanks in advance.
Edit: I did found SSPL, though only for very old versions of radio and rom, Mine is 1.93 and radio 1.00.25.05
Click to expand...
Click to collapse
Hahahaha, hi eranyanay, your worries have come true for me.. Couple of days ago, my Diamond stooped recognizing the usb port, and all the syncing and transferring have been done through bluetooth..
Now i can not revert to factory SPL, thou i have flashed a stock rom and put some of the original parts (bootloader, splashes and OS) back, just to try and make the warranty work (if they accept it )... we will see in the end
And, btw, i have been flashing and using HTCs for 3 years intensively now...

the_maker said:
Hahahaha, hi eranyanay, your worries have come true for me.. Couple of days ago, my Diamond stooped recognizing the usb port, and all the syncing and transferring have been done through bluetooth..
Now i can not revert to factory SPL, thou i have flashed a stock rom and put some of the original parts (bootloader, splashes and OS) back, just to try and make the warranty work (if they accept it )... we will see in the end
And, btw, i have been flashing and using HTCs for 3 years intensively now...
Click to expand...
Click to collapse
Oh I know!
You're one of the reasons for my question.
Its just that I couldnt find any attention to sspl around here, only to hspl.

[TUT] HOW-TO restore Diamond to stock for warranty

Due to a hardware problem in my Diamond I needed to restore it to manufacturer default. I didn't find a guide to this and since I've done the research anyway I thought I'd put together this little tutorial as the information was somewhat scattered around the forum. I hope this guide will be of use for the community.
My phone was originally branded and sim-locked by 3. After I was through with it, it was SIM-unlocked, security unlocked and had HSPL, custom ROM and a radio ported from another device. The steps below is what I did to restore it to stock. All steps might not be neccessary for you. This procedure might also work for other devices than the Diamond, but of course you need other versions of SPL, ROM etc.
1. Backup everything on your phone to your computer - use activesync, PIMbackup etc and make a copy of your Internal Storage.
2. Make a hard reset (hold vol down + enter and soft reset) and chose to format moviNAND. This step is only neccessary if you want to wipe your Internal Storage before you send the device in for repair, but I recommend it.
3. Go to www.htc.com and download the latest stock ROM (includes stock radio and SPL). You find it under Support and you enter your s/n to get the correct stock ROM for your device, complete with branding for your operator. You can also find stock ROMS here: http://forum.xda-developers.com/showthread.php?t=471699
4. Flash the stock ROM. Now you have stock ROM and Radio on your device. Stock SPL will not be installed until you've replaced HSPL with an older stock SPL and flashed ROM again.
5. Get RUU-SSPL and stock SPL from HERE:
http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39. I used the stock 1.93 SPL. Some instructions and info about restoring stock SPL is in the linked post by cmonex and due credit goes to her. I will repeat some of that info to keep this guide step-by-step. EDIT: Stock SPL 2.03 can be found here: http://forum.xda-developers.com/showpost.php?p=3359191&postcount=390
6. Put the .nbh file from the SPL you downloaded into the same folder as the extracted contents of RUU-SSPL-withoutNBH.zip and run the RUU. This flashes an old stock SPL.
7. Flash your stock ROM from step 3 again. This step is neccessary to get the correct stock SPL on your device, eg. the one that corresponds with the stock ROM you've downloaded in step 3. It was not installed in step 4, because then you still had HSPL. In step 6 you've installed a stock SPL and now the correct stock SPL will flash along with the stock ROM. After this step I got SPL 2.03 on my Diamond.
8. Remove the Security Unlock from your device using the instructions and Security Relocker by Olinex from this post by cmonex: http://forum.xda-developers.com/showpost.php?p=3299516&postcount=492
Now, my Diamond is still SIM-unlocked. I have not managed to find any info about how to restore the SIM-lock, but it is hopefully not neccessary for warranty. As far as I can tell, the unlock doesn't show anywhere, but of course all they need to do is to try a SIM-card from another operator...
If anyone has info about how to restore SIM-lock, then I'll update this guide with that info.

good job...
moderator make this "sticky"

3dward87 said:
good job...
moderator make this "sticky"
Click to expand...
Click to collapse
I second that, it contains links to stock ROMs, that'll hopefully stop a million topics about it lol.

This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..

Da9L said:
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Click to expand...
Click to collapse
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.

where can i read more information about jumpspl, how it works and everything?

eranyanay said:
where can i read more information about jumpspl, how it works and everything?
Click to expand...
Click to collapse
Look in the Xda-wiki, search and google, and not just in the Diamond section.

sticky please
this needs to be a sticky topic.

losdrivare said:
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
Click to expand...
Click to collapse
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.

Da9L said:
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Click to expand...
Click to collapse
Sorry to hear it and I'm afraid I'm out of ideas. After all, my little tutorial is primarily aimed at those whose Diamonds have working screens...
On another note, my Diamond came back from warranty repair and the repair shop had not noticed anything that would void my warranty. In the meantime I got myself a Topaz and now I've sold my Diamond, but I'll be checking this thread from time to time.

Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)

donsalari said:
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
Click to expand...
Click to collapse
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.

losdrivare said:
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
Click to expand...
Click to collapse
Very true!!! Ok cool... Flashing back to stock!!
Thanks..

Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.

Da9L said:
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Click to expand...
Click to collapse
Another idea: maybe you can find some a VNC program that also works the "other way" with windows mobile, so that you can get a window on your PC with the screen of your device?

Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...

Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me

bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi

herpez said:
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Click to expand...
Click to collapse
k3nnyboiboi said:
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
Click to expand...
Click to collapse
If you manage to install ANY stock SPL and then flash the correct ROM for your country and operator then you automatically get the correct SPL too, since stock ROMs include SPL. If you go to htc.com and type in your s/n then you automatically get the latest ROM for your device and operator.
k3nnyboiboi said:
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
Click to expand...
Click to collapse
I only link to the SPLs provided by olipro and cmonex in the hard-SPL thread. If you need closer info about SPLs I suggest you ask there. I only tried to revert back to stock SPL 1.93 myself and it worked just like described in first post.

Thanks Op
Managed to restore it no problem, but took ages

Flashing can't start, and cant't find solution the after searching the forum

So as you can figure out from the thread title I have a problem flashing my htc diamond.
I have installed a HardSPL version 1.30 OliNex, I can confirm that becouse on the three color screen there is a text saying "1.30 OliNex".
I still have the original ROM that comes with the phone when I bought it, so this meant to be my first flashing.
I want to flash the phone with this rom http://forum.xda-developers.com/showthread.php?t=593678 it is a WM 6.5 based ROM.
Because in the ROM package there wasn't a ROMUpdateUtility.exe I used it from other ROM package.
Connected via ActiveSync and followed the wizard. The phone reset and there came a gray screen with a progress bar. Now both progress bars on the phone and on the PC screen remain 0% and after a wile RUU finished with 262 ERROR Connection error, see the attached picture.
After that I tried to flash it from Internal Storage. A followed the steps according the procedure, and after the three colored screen it came the gray screen with "Loading..." message. I waited for almost 30 minutes and nothing happened.
What seems to be the problem?
I assumed about firewall disabling the connection. But I turned off the firewall and again the same story.
Then somewhere I found that there is incompatibility with the RUU and HardSPL version, but tried to flash with the same RUU that I used when I was installing HardSPL.
Then I tough that the problem is about flashing unsigned ROM on a signed HSPL, but it is not that the ROM is signed.
I am afraid to use MTTY so I don't brick my phone, because this is my first time flashing a Diamond.
I'm confused What seems to be the problem?
Any help can be welcomed.
Could this be indication of a hardware problem? When waiting for the "Loading..." message disappear the back cover warms a little.
Thanks.

1. Did you use the RUU from my thread?
2. NEVER USE AN H-SPL RUU TO FLASH ANYTHING OTHER THAN H-SPL!
3. is this a CMDA phone. IE, what network are you on?

Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?

Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
EDIT: I did tried the RUU you recommended in your thread but it's the same.
I think it is in the PDA.

Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"

Hmmm..
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.

johnyboy_ said:
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Click to expand...
Click to collapse
The connection between PC and PDA is made, because as I said there is a progress bar on the phone screen too.
djfuego said:
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
Click to expand...
Click to collapse
As I understand you, you are saying to install later version of Hard SPL right?
So to install a new version of Hard SPL I just need to do the same procedure as the first time, or I have to uninstall the previous one?
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?

djandreski said:
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
Click to expand...
Click to collapse
Presuming from your post, you are using a signed Olinex SPL, i doubt that the rom has been signed be OliNex, the only difference with Dev is you can flash any Rom, flash the Dev one from my thread, nothing to be afraid of
Good Luck
Badwolve1

What are the steps of installing new SPL?
Do I just need to do the same procedure as the first time, or I have to uninstall the previous one(somehow)?
UPDATE: I did it, I successfully flashed my Diamond PDA! It seams that the problem was in the SPL I installed 1.40 OliNex Unsigned and it flashed like a charm. Thanks guys for the help. Now this thread can be closed, or do I have to close it myself.

Great!
Glad it all worked out