Flashing Problem - Touch Diamond, MDA Compact IV ROM Development

Hi All.
I Need your help.
I have a Diamond Runnig HardSPL 1.40 Olinex, Gen Y ROM, 1.11 Radio.
Everything was fine until my diamond enter on the three color flash screen, i instaled 3 diferent ROM and it's not booting any more. I tried everything and nothing heappened, a shut down install a new ROM and it don't boot, backing to the flash screen.
USB is working fine.
Some one can help me? URGENT!!!!!

you means you always enter to 3 color screen when you boot?
you can try to flash to official rom which sometime it can help.
or another silly suggestion, you sure your VolDown button was not stuck??

Related

PV HERMES Rom Expired????????

Hello.
I have installed a PV Hermes WM 6.1 Rom.
It now says : thank you for using this software...etc
I think it was for betatesters, and now it shows only a splash screen, and i CANNOT install another ROM.
I tried to install by starting in BOOTLOADER, but it does not help.
What can i do???
emipop said:
Hello.
I have installed a PV Hermes WM 6.1 Rom.
It now says : thank you for using this software...etc
I think it was for betatesters, and now it shows only a splash screen, and i CANNOT install anothor ROM.
I tried to install by starting in BOOTLOADER, but it does not help.
What can i do???
Click to expand...
Click to collapse
I think I read somewhere (but have not tried), do a hard reset, and when the screen that says Tap to begin using your device pops up, start attempting to flash from there.
But they "should" flash from the bootloader screen.
I had exactly the same problem. Tried all the tricks to go back to the previous ROM. I also tried boog321's hard reset idea, but it just puts you back into the bootloader. HOWEVER, when I then went through the screen alignment process (just for fun), lo! it works!
The problem is that i can`t get inside windows anymore. It stays at the screen 3 seconds after power up. Is there a way to hardware reset?
emipop said:
The problem is that i can`t get inside windows anymore. It stays at the screen 3 seconds after power up. Is there a way to hardware reset?
Click to expand...
Click to collapse
Just flash a different rom dude!! probably a expired beta rom.
i have tried to falsh 4 differnt ROM`s. It makes 2% and says rom orrupter or something.
Tried installing via MicroSD card? I installed the same ROM a while back...
Hey. I just re-flashed right now after I installed an expired beta by mistake.
Start with the Hermes connected USB, showing the splash out of luck screen.
1. Hold both Power and the ok button on the left and then RESET with the stylus. It should go in tri-color mode
2. Flash a known good ROM
Good luck!
Bro just flash your ppc using other ROM (flash it in bootloader mode) when its in the hermes rom upgrade tap the (force using safe SSPL) it will do the trick.
I already said i did that.
After 1% it stopped and says : ERROR 270. UPDATE ERRROR: The image file is corrupted please check your update utility.
I have done this with 5 roms now.
Will try microsd install.
Hope you have Hard SPL, you need it for sd card flash...
I solved the problem with the bad ROM.
I downloaded an official rom from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades
I has done a clean install.
But i still can§t install another rom, from the forum.
Will try again.
emipop said:
I solved the problem with the bad ROM.
I downloaded an official rom from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades
I has done a clean install.
But i still can§t install another rom, from the forum.
Will try again.
Click to expand...
Click to collapse
Are you sure you have HardSPL installed and CID unlocked your device?

Impossible to flash any ROM radio , stop at 7%

hi all, my situation in this:
i ve an htc s300+ with hardspl 1.30 installed that in boot loader write "WLAN error" , when boot it is blocked to 2nd screen (HTC logo). i ve try with any solution on this forum.. with mtty not solution, with "splxploit" no solution.. i understand that the problem is when i try to flash a Rom radio it don't wont load over 7% and reboot in boot loader, or a original italian complete rom WM5 it don't wont load over 13% but not reboot.
if i flash only the ROM WM6 coocked it load full but the problem is the same.. (after reboot blocket to 2nd screen)..i ve try to flash also directly with mini SD but the loading stopped after start (about 13%)..
the situation is the same if i load with "splxploit" the hardspl 1.20, or sspl 1.05 or 1.06...
i try all solution in my mind... but no resolve this problem..
can anyone with more experience that me to help?
thanks
sorry but i am italian and my english is not good..
I think you have not complete reading all instruction before you start.
HARDSPL Olipro 1.30 is not able to flash Radio Rom as feedback by many.
You should use Olipro 1.20 or Des's SPL.
Sorry, I have the same problem,
How I can downgrade the H-SPL from 1.3 to 1.2 if the P3600 don't boot on, it is stop at startup logo HTC
Thx
Just put your device manualy in bootloader and flash again...It should work
IT don't work.
The process it is ok at 100%, but if I put the pda in bootloader I have again 1.30
Where I wrong?
Have you tried to flash from SD Card? Maybe this would work differently.
Try flashing HTC official rom
As stupid as it sound, it worked for me. it seems the official WM5 rom has some recovery features. It takes forever to flash (and obviously it does some different stuff than cooked roms) but it took my bricked trinity from its brick mode at least twice the past 3 years. If you can't get hold on one, although I am sure it is on this forum, PM me and I will upload it for you. Just too tiered to do so if you have another source to take it from.
Look for RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship. Be aware after it you may need to update the radio as well, but this is easy.
BigE
Please upload the file!!!!!!!!
Thx
for lazy ppl who do not search
http://rapidshare.com/files/47349234/latest_dopod_wm6_anznospl.rar.html
BigE
try this one
http://cid-8231c261cbdd4326.skydriv....751.5|_6275|_1.56.70.11|_108|_Ship.part1.rar

Diamond Stuck up at the welcome screen

Dear Sir
My diamond got stuck up at the welcome screen or else in the alignment screen. I've flashed many roms number of times before but this time this happened after a hard reset- using Macadam 1.2 (latest).
My bootloader reads - Diam140 MFG 64M; SPL-1.40. Olinex. After this I've flashed back to the latest indian stock rom i.e. First to (RUU_Diamond_hTC_Asia_India_1.93.720.4_Radio_Signed_Diamond_52.62.25.34_1.13.25.24_ShiP) but know result & (RUU_Diamond_hTC_Asia_India_1.93.720.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.07_Ship_R). After going through the forums- I understood that I've to step down to stock spl. But even after successful flashing, the boot loader shows the same- "SPL-1.40.OliNex".
I'm unable to use the jump SPL, because I can't pass through the alignment screen. Please help, is there any way to JUMP SPL without operating the phone.
Or else how can I come back to the stock spl.
Please Help.........................
Regards
Furthermore, I've tried using mtty to following the procedure:
Correct sequence is as follows:-
1. Launch ActiveSync on PC
2. Go to connection settings
3. Uncheck the Allow USB Connection
4. bring the device to bootloader. AND connect to the PC.
5. Now, run mtty1_1_.42_538 on PC.
6. CMD>task 29
7. Flash the ROM of your choice
Then flashed the stock rom again. But the problem remained.
jockyw2001 - suggested me on PM to do- "in mtty: set 16 0 then reboot'- but nothing happened. Or I didn't follow the correct steps... can anyone explain & help please....
[UPDATE]where do I get the commands for mtty
Can anyone tell me the link where I can get the commands to be used in mtty... Is there anyway to bypass the screen alignment part during start up after a hard reset.... how can I JumpSPL in a handset where the touch screen is not working.. but the screen is not completely dead, i.e. on tapping the "+" sign is moving after around 5 or 7 mins of the tap...
Please help guys.... I'm waiting to be rescued by some WM wizard from this great community.....
Regards
wizards- all'r failing or what- very few people with clear funda
cmonex please help....
hi man
i had the same problem, with all the rom around
than i understand that the problem was the radio rom
try to flash the lastest radio..i use the 1.13
Flash a Rom without screen alignment
Hi
If you on bootloader and you have 1.40olinex then flash a 1.13 radio then flash a Rom without Screen alignment process. It might help. Good luck

Need help after flashing

hi guys,
have done the Hard SpL 1.3, added radio 1.5 and tried flashing the WWE JADECore + Manila2D 1.2 PTG version successfully but however the device does not go pass the HTC screen.
i then tried to flash Mary V3.7 lite but it does not load. Requires me to do recovery. However upon recovery , it shows by hello nasty - smart mobility. Stuck right there
i flash JADECore + Manila2D 1.2 PTG again... its loading and successful, however it still reboots to hello nasty - smart mobility and stop again.
Did i miss something out? i dont understand as i assume after the Hard SPL and radio , the rest of the rom can be flashed.
i Have tried several times with this rom and mary's rom
and have soft resetted several times.
Hope for some help.
any help at all?
try official ROM first
hmm okies..
could it be that i didn't unlock the phone yet?
now its in bootloader mode.
how do i flash the unlocker or official rom in?
i still have the original wm5 disc
tried flashing the RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship original wm6.1 rom but it stops at 28% everytime i try.
the custom roms flash nicely and everything boots up until the first or 2nd page then it stops.
i'm on SPL 1.3olio and i guess the radio doesnt matter but its a 1.5
anyone could help? i'm offering a small token via paypal for anyone who can walk my trinity back to the light..
Although Olipro's Hard-SPL 1.30 is the newest version, many people have reported not being able to upgrade their device with this version running. For now it is recommended to use 1.20 or Des' crash-proof SPL for successful upgrades
Click to expand...
Click to collapse
Found at http://trinityguides.info
have used SPLxploit and it changed to SPL 3.03000
what do i do next? install HardSPL? Install CID unlocker?
boot from SD?
someone ? anyone?

Kaiser loocked before flashing android

Yesterday I try to flash android on nand in my at&t tilt, with valentines rom, I flash the kernel recomended and follow the instructions but the rom don't boot, so, I dedided re flash Winmo.
First at all, I try to flash a cooked rom I make, the flash completed 100% and the phone reboot, but stuck on RBG screen!!
Then I try to flash winmo 6.1 custom rom, and this one works well!! but.........
is the only rom I can use, cause if I flash another rom (custom or cooked) the boot stuck on RBG screen (the screen where the radio, roms and version appears in red letters)
I try to unlock security again, thinking this maybe the problem, using pof tutorial, and having in tricolor screen the message SECURITY UNLOCKED in red letters. before that, I flash again another rom but the problem still!!
I try to flash a winmo 6.0 custom rom, to use jowkys tutorial but the rom stuck in RBG screen too.
So... What can I do? I'm confused... PLEASE HELP ME!!!!!!
For extra info... in memory data, in the part of internal storage only appear 30Mb!!!! and not the 145Mb that should be!!!
SLP: 1.0 olipof
Radio: 1.70Olinex
ROM: Winmo 6.1 oficial
I think you need a recent hard SPL.
Look at here: http://forum.xda-developers.com/showthread.php?t=498320
If I am correct I installed DaveShaw's 3.34. I can't check it because i'm not a kaiser owner now.
Bye

Categories

Resources