Impossible to flash any ROM radio , stop at 7% - P3600 ROM Development

hi all, my situation in this:
i ve an htc s300+ with hardspl 1.30 installed that in boot loader write "WLAN error" , when boot it is blocked to 2nd screen (HTC logo). i ve try with any solution on this forum.. with mtty not solution, with "splxploit" no solution.. i understand that the problem is when i try to flash a Rom radio it don't wont load over 7% and reboot in boot loader, or a original italian complete rom WM5 it don't wont load over 13% but not reboot.
if i flash only the ROM WM6 coocked it load full but the problem is the same.. (after reboot blocket to 2nd screen)..i ve try to flash also directly with mini SD but the loading stopped after start (about 13%)..
the situation is the same if i load with "splxploit" the hardspl 1.20, or sspl 1.05 or 1.06...
i try all solution in my mind... but no resolve this problem..
can anyone with more experience that me to help?
thanks
sorry but i am italian and my english is not good..

I think you have not complete reading all instruction before you start.
HARDSPL Olipro 1.30 is not able to flash Radio Rom as feedback by many.
You should use Olipro 1.20 or Des's SPL.

Sorry, I have the same problem,
How I can downgrade the H-SPL from 1.3 to 1.2 if the P3600 don't boot on, it is stop at startup logo HTC
Thx

Just put your device manualy in bootloader and flash again...It should work

IT don't work.
The process it is ok at 100%, but if I put the pda in bootloader I have again 1.30
Where I wrong?

Have you tried to flash from SD Card? Maybe this would work differently.

Try flashing HTC official rom
As stupid as it sound, it worked for me. it seems the official WM5 rom has some recovery features. It takes forever to flash (and obviously it does some different stuff than cooked roms) but it took my bricked trinity from its brick mode at least twice the past 3 years. If you can't get hold on one, although I am sure it is on this forum, PM me and I will upload it for you. Just too tiered to do so if you have another source to take it from.
Look for RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship. Be aware after it you may need to update the radio as well, but this is easy.
BigE

Please upload the file!!!!!!!!
Thx

for lazy ppl who do not search
http://rapidshare.com/files/47349234/latest_dopod_wm6_anznospl.rar.html
BigE

try this one
http://cid-8231c261cbdd4326.skydriv....751.5|_6275|_1.56.70.11|_108|_Ship.part1.rar

Related

Can't flash anything after installing PDAVIET 2.07.06.PV

I've been using Mun_rus's WM6 ROM for quite a while and seeing that PDAVIET's rom was built on a more recent WM6 ROM I decided to flash PDAVIET 2.07.06.PV.
Since then I cannot flash anything on my Trinity, the update utility starts and when the progress bar reaches around 84% half the screen on the Trinity goes funny. The progress bar on the PC reaches the 100% (while the screen on the Trinity goes blank slowly slowly) but upon restarting the device PDAVIET ROM loads up again intact as if I have just done a soft reset!
I've even tried flashing WM5 again but without any success.
Trying to flash Hard-SPL does not work either and I'm running out of ideas now :-( Anyone else has this problem please? I would love to try flashing a ROM with an original IPL SPL but cannot find one. My bootloader currently says IPL 1.5/SPL 9.99.CP.
Yes I am having a similar problem. It starts to flash then stops reboots and on my pc says image fiile corrupted. I have re downloaded and extracted the files but it happens everytime. However. My trinity when it reboots is stuck in the splash screen.
I had a similar problem, though not quite what you're describing. Try removing the Mini SD (storage card) before flashing.
Also, try entering bootloader fisrt before before flashing from PC.
Hope that helps.
i have the same problem...
i get 100% done and than it is still the old one..
Well, I have now sorted it. Go to this link read first post and download and use the unbrick.
http://forum.xda-developers.com/showthread.php?t=308691&highlight=splxploit-windows
I had to run it 3 times but it has worked and now I have flashed a new rom on it and it is working fine now
deniser said:
Well, I have now sorted it. Go to this link read first post and download and use the unbrick.
http://forum.xda-developers.com/showthread.php?t=308691&highlight=splxploit-windows
I had to run it 3 times but it has worked and now I have flashed a new rom on it and it is working fine now
Click to expand...
Click to collapse
I've run the splxploit a couple of times as well. It seems to finish the process succesfully but the problem persists :-( And mine is not stuck on splash screen, the device boots normally, it's just that whatever I flash does not work. Any more ideas please?
I tryed the all i think, read the all forum up and down, started in different ways, but no rom of SSL apply...
What is that!
I am stuck with this rom?
Any of the pro cookers can help with this please? I just need to understand what could be wrong, not necesseraly a solution
capeli said:
I had a similar problem, though not quite what you're describing. Try removing the Mini SD (storage card) before flashing.
Also, try entering bootloader fisrt before before flashing from PC.
Hope that helps.
Click to expand...
Click to collapse
Hey many thanks Removing the miniSD solved my problem I flashed at least a 100 ROMS in my life and never bothered removing the memory card before ... but there you go
hi, i had the same problem. i flashed my trinity with original htc rom and after that when i tried to flash with any other rom it gave me success message after every try but in my phone there was still the same htc rom. i used that : http://forum.xda-developers.com/showthread.php?t=293632 AND IT WORKS. FROM THE MOMENT WHEN I USED THAT FILE I FLASHED MY TRINITY 2 TIMES WITH THE SAME ROMS WHICH DIDN`T WORKED PREVIOUS. you need to copy that file to your trinity and follow the instructions from the readme file. in my case i only opened it ,it started bootloader mode ,i disconected usb and connected it again and started ROMUpdateUtility with rom which i wanted.
interesting... so why does the miniSD card affect the flash?
kta- had you tried running sspl and then flashing during your failed attempts? (just curious)

Unable to install Haard SPL (OSX+Parallels+Vista Ultimate)

Hi,
I tried many times to install the hard spl version 1.34 on my new Diamond, but I have always the same problem:
- the program start
-it run since the boot loader mode appear on the screen
-then appear the progress bar and then ..... NOTHING.
I'm not new to flash and add new software, infact before the Diamond I had a Trinity flahed many and many times (Kaiser, Elegance Edition, etc....).
What can I do to solve the problem ? Really I don't undestand.
Please If someone has solved the problem post the solution.
Thank's
Post your SPL upgrade procedure, step by step.
We'll try to see where you might've gone wrong.
Did you sync your diam with active sync?
Did you try the spl-manual?
Maybe it is also good to give a link to the post you got the SPL from, so we know exactly which version you have (signed/unsigned).
I could not do it on my macbook pro either. IN teh end I resorted to boot camp and it worked fine
The procedure I made is still the same.
1. connect to activesync
2. start the exe
3. the screen of the diamond star the boot loader mode
4. appear the progress bar both in the pc screen and the diamond screen
5. the procedure stops and no data are transferred to the diamond
I tried all the three version of hard spl but the problem is still present.
The version of hard spl (from 1.24 to 1.34) is the one you can find in the first page of the forum.... belive me I did it many times in the past and I read very well the procedure suggested in the post.
However I will try to use boot camp.
Thank' s to everibody .

Problems with Hard spl

Ok so i wanted to instal the new swiftblade 4.0 rom,its my first time.So I downloaded hardspl developers edition,well you know the unsigned hradspl.I did all the steps and when the process started in took only a minute if not less,after this minute it said that i have succesfully installed hardspl ,but it said it would take 10 minutes. My phone reboted and it was like a new diamond,I had to set it up again and the data was erased.So I entered bootloader mode and in didn't show me that i had hardspl installed.Can anyone help me?I want to install the swiftblade rom
sounds to me like you were successful in your upgrade usually takes a few seconds- not sure what hardspl you flashed but check back in the thread from where you got it to confirm what should say at boot mine says Olinex on it - hope this helps
It doesn't say the right thing, I have tried both Sighed and Unsighed Hard SPL Same old thing.Takes a few seconds and then says like it was successful ,but when I enter bootloder mode it doesn't say the right things

Need help after flashing

hi guys,
have done the Hard SpL 1.3, added radio 1.5 and tried flashing the WWE JADECore + Manila2D 1.2 PTG version successfully but however the device does not go pass the HTC screen.
i then tried to flash Mary V3.7 lite but it does not load. Requires me to do recovery. However upon recovery , it shows by hello nasty - smart mobility. Stuck right there
i flash JADECore + Manila2D 1.2 PTG again... its loading and successful, however it still reboots to hello nasty - smart mobility and stop again.
Did i miss something out? i dont understand as i assume after the Hard SPL and radio , the rest of the rom can be flashed.
i Have tried several times with this rom and mary's rom
and have soft resetted several times.
Hope for some help.
any help at all?
try official ROM first
hmm okies..
could it be that i didn't unlock the phone yet?
now its in bootloader mode.
how do i flash the unlocker or official rom in?
i still have the original wm5 disc
tried flashing the RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship original wm6.1 rom but it stops at 28% everytime i try.
the custom roms flash nicely and everything boots up until the first or 2nd page then it stops.
i'm on SPL 1.3olio and i guess the radio doesnt matter but its a 1.5
anyone could help? i'm offering a small token via paypal for anyone who can walk my trinity back to the light..
Although Olipro's Hard-SPL 1.30 is the newest version, many people have reported not being able to upgrade their device with this version running. For now it is recommended to use 1.20 or Des' crash-proof SPL for successful upgrades
Click to expand...
Click to collapse
Found at http://trinityguides.info
have used SPLxploit and it changed to SPL 3.03000
what do i do next? install HardSPL? Install CID unlocker?
boot from SD?
someone ? anyone?

[Q] Problems with bootloader [SOLVED]

I had 3.29 HardSPL, i used Android on nand for quite some time, after that i decided to flashed back to WinMo to check something out, in one of the guides, it told me to put the kaisimg.nbh and kaisdiag.nbh, (i had flashed back to WInMO several times but never included the Kaisdiag.nbh, since the guide mentioned it i thought it was something good to do)
i used the official WM6.1 and entered bootloader as usual... then my device reset in the middle of flashing...
When i tried again bootloader got stuck at 'Loading...' and the bootloader was now showing 3.34.000
Now i am unable to flash the windows ROM or HardSPL as they all got stuck in the bootloader at 'Loading...' also tried with bootloader in USB mode... nothing
Please help me... thanks in advance
BTW, luckily the android kernel was still functional and i can use it for now...
I posted this in the TyTn General Discussion section but since i got no reply for days, i reposted it here, so sorry in advance for the double thread.
Put the kaiser in boot mode, connect to a pc and flash an original rom from windows. Then reflash hard spl.
l1q1d said:
Put the kaiser in boot mode, connect to a pc and flash an original rom from windows. Then reflash hard spl.
Click to expand...
Click to collapse
Thanks for the reply... i tried this, dont know if i did something wrong but it still got stuck, i used the stock 6.1 asian, it was originally a swedish kaiser so do i need that particular rom?? i will try again...
I tried RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.rar but while it was flashing, it got to 1% on the computer and then the device just resets
It said Error [294]: Invalid vendor ID
the update utility could not be used for your PDA phone on my PC
Finally solved... i went to htc website and downloaded the update using my phones serial number... i successfully flashed back to WinMo using that ROM... now i can use hardspl again... thanks for all the help

Categories

Resources