Unable to install Haard SPL (OSX+Parallels+Vista Ultimate) - Touch Diamond, MDA Compact IV ROM Development

Hi,
I tried many times to install the hard spl version 1.34 on my new Diamond, but I have always the same problem:
- the program start
-it run since the boot loader mode appear on the screen
-then appear the progress bar and then ..... NOTHING.
I'm not new to flash and add new software, infact before the Diamond I had a Trinity flahed many and many times (Kaiser, Elegance Edition, etc....).
What can I do to solve the problem ? Really I don't undestand.
Please If someone has solved the problem post the solution.
Thank's

Post your SPL upgrade procedure, step by step.
We'll try to see where you might've gone wrong.
Did you sync your diam with active sync?
Did you try the spl-manual?

Maybe it is also good to give a link to the post you got the SPL from, so we know exactly which version you have (signed/unsigned).

I could not do it on my macbook pro either. IN teh end I resorted to boot camp and it worked fine

The procedure I made is still the same.
1. connect to activesync
2. start the exe
3. the screen of the diamond star the boot loader mode
4. appear the progress bar both in the pc screen and the diamond screen
5. the procedure stops and no data are transferred to the diamond
I tried all the three version of hard spl but the problem is still present.
The version of hard spl (from 1.24 to 1.34) is the one you can find in the first page of the forum.... belive me I did it many times in the past and I read very well the procedure suggested in the post.
However I will try to use boot camp.
Thank' s to everibody .

Related

HArd Spl problem

Yesterday i downloaded the Tytn htc wm6 original rom, i unrared it and using the nbhtool i splitted the nbh files.
I obtained six .nb files: the herm_extended rom, windows.nd, the primary and secondary splash and ipl and spl files.
Following the istructions tha i found here i recomompiled the rom using only the windows. nb, the extender rom and the two splas files.
My HErmes200 was hard spl 2.10 olipro and i flashed it many times, anyway..
I flashed this ROM and everything works flawlessy ( i added some softwares like always). This night i decided to change the splas screens so i created them and prepared the nb files thaf after i compiled using the nbhtool.
When i went to flash them, at the moment you press on the autodetect button starting to flash,, the ruu wrapper tells me that my spl is an unknown version ...
Well i tried to flas the hard spl v7 following the istructions, all seems to work well but it does not update my spl version anymore and if i press the two ok buttons the restart thing and the on-off button to see my spl versionentering the bootloader i am able to see for less than 1 second the 3 colors screen of the boot loader and after it only a gray screen asking me if i want to erase everything or not.
My hermes works perfectly and i flashed the splash scrreens just forcing to flas in hard spl mode but.. i want to know what to do because i would love to go back to the 2,10 olipro spl tha is very safe.
Thankyou to all of you that will answer to me.
Massimo
part 2
I decided to chaange the splash screen again so i prepared the nbh file and using the RUUWrapper.exe i flashed it.
This time at the beginning of the flash process i told to the RUU that my device was hardspl with the olipro 2.10, i followed all the normal istructions and this time the 3 colors screen was normal indicatind the right 2,10 olipro version.
Now i don't understand anything anymore
Can someone expert explain to me what is happening?
thanks
M

Problems with Hard spl

Ok so i wanted to instal the new swiftblade 4.0 rom,its my first time.So I downloaded hardspl developers edition,well you know the unsigned hradspl.I did all the steps and when the process started in took only a minute if not less,after this minute it said that i have succesfully installed hardspl ,but it said it would take 10 minutes. My phone reboted and it was like a new diamond,I had to set it up again and the data was erased.So I entered bootloader mode and in didn't show me that i had hardspl installed.Can anyone help me?I want to install the swiftblade rom
sounds to me like you were successful in your upgrade usually takes a few seconds- not sure what hardspl you flashed but check back in the thread from where you got it to confirm what should say at boot mine says Olinex on it - hope this helps
It doesn't say the right thing, I have tried both Sighed and Unsighed Hard SPL Same old thing.Takes a few seconds and then says like it was successful ,but when I enter bootloder mode it doesn't say the right things

Cannot Update 1.93 rom with HardSPL

Hi, i tried all HardSPL Versions i could find, but that happens every time:
- The ROM Upgrade Utility starts,
- i check all the answer boxes, until the diamond asks if the bootloader program is ok and i push the button.
- the Bootloader starts (3-colored screen), and the progress bar at the top of the screen comes up, but shows 100% after a few seconds.
- The ROM Upgrade Utility says Upgrade is finished and the Diamond resets, but shows still original spl Version.
I Installed net 3.5 compact, does not help.
Yes i read the instructions and i propably did ROM Upgrades a dozen times in the past years, but i am still clueless. Plz help.
The Modifier said:
Hi, i tried all HardSPL Versions i could find, but that happens every time:
- The ROM Upgrade Utility starts,
- i check all the answer boxes, until the diamond asks if the bootloader program is ok and i push the button.
- the Bootloader starts (3-colored screen), and the progress bar at the top of the screen comes up, but shows 100% after a few seconds.
- The ROM Upgrade Utility says Upgrade is finished and the Diamond resets, but shows still original spl Version.
I Installed net 3.5 compact, does not help.
Yes i read the instructions and i propably did ROM Upgrades a dozen times in the past years, but i am still clueless. Plz help.
Click to expand...
Click to collapse
Is it a U.S. version Diamond?
http://forum.xda-developers.com/showthread.php?p=2963492#post2963492
Stupid me
Hi, now i tried the ROM Upgrade (not the HardSPL) and it works. Seems that the HardSPL Upgrade worked from the very beginning, but i got fooled by the T-Mobile start screen still showing 1.93 (at the bottom of the screen), and the ROM Upgrade Utility also told me that the current ROM version is 1.93.something.
... ok Upgrade finished, says 2.03.something now so something changed after all.
... Yep thats the new ROM, i made it.
But after the soft reset theres is still the T-Mobile start screen withe the magenta dots i dont get it: new ROM, but still T-Mobile Logo???
ROM Version is now 2.03.401.2 WWE , does that mean v6.4FullHDTFl.nbh is installed?

Impossible to flash any ROM radio , stop at 7%

hi all, my situation in this:
i ve an htc s300+ with hardspl 1.30 installed that in boot loader write "WLAN error" , when boot it is blocked to 2nd screen (HTC logo). i ve try with any solution on this forum.. with mtty not solution, with "splxploit" no solution.. i understand that the problem is when i try to flash a Rom radio it don't wont load over 7% and reboot in boot loader, or a original italian complete rom WM5 it don't wont load over 13% but not reboot.
if i flash only the ROM WM6 coocked it load full but the problem is the same.. (after reboot blocket to 2nd screen)..i ve try to flash also directly with mini SD but the loading stopped after start (about 13%)..
the situation is the same if i load with "splxploit" the hardspl 1.20, or sspl 1.05 or 1.06...
i try all solution in my mind... but no resolve this problem..
can anyone with more experience that me to help?
thanks
sorry but i am italian and my english is not good..
I think you have not complete reading all instruction before you start.
HARDSPL Olipro 1.30 is not able to flash Radio Rom as feedback by many.
You should use Olipro 1.20 or Des's SPL.
Sorry, I have the same problem,
How I can downgrade the H-SPL from 1.3 to 1.2 if the P3600 don't boot on, it is stop at startup logo HTC
Thx
Just put your device manualy in bootloader and flash again...It should work
IT don't work.
The process it is ok at 100%, but if I put the pda in bootloader I have again 1.30
Where I wrong?
Have you tried to flash from SD Card? Maybe this would work differently.
Try flashing HTC official rom
As stupid as it sound, it worked for me. it seems the official WM5 rom has some recovery features. It takes forever to flash (and obviously it does some different stuff than cooked roms) but it took my bricked trinity from its brick mode at least twice the past 3 years. If you can't get hold on one, although I am sure it is on this forum, PM me and I will upload it for you. Just too tiered to do so if you have another source to take it from.
Look for RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship. Be aware after it you may need to update the radio as well, but this is easy.
BigE
Please upload the file!!!!!!!!
Thx
for lazy ppl who do not search
http://rapidshare.com/files/47349234/latest_dopod_wm6_anznospl.rar.html
BigE
try this one
http://cid-8231c261cbdd4326.skydriv....751.5|_6275|_1.56.70.11|_108|_Ship.part1.rar

Diamond Stuck up at the welcome screen

Dear Sir
My diamond got stuck up at the welcome screen or else in the alignment screen. I've flashed many roms number of times before but this time this happened after a hard reset- using Macadam 1.2 (latest).
My bootloader reads - Diam140 MFG 64M; SPL-1.40. Olinex. After this I've flashed back to the latest indian stock rom i.e. First to (RUU_Diamond_hTC_Asia_India_1.93.720.4_Radio_Signed_Diamond_52.62.25.34_1.13.25.24_ShiP) but know result & (RUU_Diamond_hTC_Asia_India_1.93.720.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.07_Ship_R). After going through the forums- I understood that I've to step down to stock spl. But even after successful flashing, the boot loader shows the same- "SPL-1.40.OliNex".
I'm unable to use the jump SPL, because I can't pass through the alignment screen. Please help, is there any way to JUMP SPL without operating the phone.
Or else how can I come back to the stock spl.
Please Help.........................
Regards
Furthermore, I've tried using mtty to following the procedure:
Correct sequence is as follows:-
1. Launch ActiveSync on PC
2. Go to connection settings
3. Uncheck the Allow USB Connection
4. bring the device to bootloader. AND connect to the PC.
5. Now, run mtty1_1_.42_538 on PC.
6. CMD>task 29
7. Flash the ROM of your choice
Then flashed the stock rom again. But the problem remained.
jockyw2001 - suggested me on PM to do- "in mtty: set 16 0 then reboot'- but nothing happened. Or I didn't follow the correct steps... can anyone explain & help please....
[UPDATE]where do I get the commands for mtty
Can anyone tell me the link where I can get the commands to be used in mtty... Is there anyway to bypass the screen alignment part during start up after a hard reset.... how can I JumpSPL in a handset where the touch screen is not working.. but the screen is not completely dead, i.e. on tapping the "+" sign is moving after around 5 or 7 mins of the tap...
Please help guys.... I'm waiting to be rescued by some WM wizard from this great community.....
Regards
wizards- all'r failing or what- very few people with clear funda
cmonex please help....
hi man
i had the same problem, with all the rom around
than i understand that the problem was the radio rom
try to flash the lastest radio..i use the 1.13
Flash a Rom without screen alignment
Hi
If you on bootloader and you have 1.40olinex then flash a 1.13 radio then flash a Rom without Screen alignment process. It might help. Good luck

Categories

Resources