i need a coach. i have a freshly flashed verizon samsung i910. it is making/recieving calls. i have all the correct settings for metro for the sms/mms/ dialing #777 etc... EXCEPT!!! I can NOT get the password "metropcs" to stick when i enter it into the settings. I have a verizon vx6800 "ntc titan/mogul" I had it flashed to metro, and put all the same settings into it, and it's password stayed in place. All is working purrrfect on it. mms/sms/pic&text/calls/gps/instant messaging, etc.. I have been told that on the omni i910, the password has to be edited via computer/usb cable..reg edit.. perhaps. If i knew what/where to edit i feel confident enough to try it. can anyone direct me with good info, as to what software to use, and where in the registry, i need to edit? I have mobile reg editor, and qpst, and active sync installed, as well as tcmdpocketarm total commander for pocket-pc. i really want to get this phone working, someone please come to the rescue. my email is [email protected] cell# 707-413-8127...augie. and thanks in advance...
augie1 said:
i need a coach. i have a freshly flashed verizon samsung i910. it is making/recieving calls. i have all the correct settings for metro for the sms/mms/ dialing #777 etc... EXCEPT!!! I can NOT get the password "metropcs" to stick when i enter it into the settings. I have a verizon vx6800 "ntc titan/mogul" I had it flashed to metro, and put all the same settings into it, and it's password stayed in place. All is working purrrfect on it. mms/sms/pic&text/calls/gps/instant messaging, etc.. I have been told that on the omni i910, the password has to be edited via computer/usb cable..reg edit.. perhaps. If i knew what/where to edit i feel confident enough to try it. can anyone direct me with good info, as to what software to use, and where in the registry, i need to edit? I have mobile reg editor, and qpst, and active sync installed, as well as tcmdpocketarm total commander for pocket-pc. i really want to get this phone working, someone please come to the rescue. my email is [email protected] cell# 707-413-8127...augie. and thanks in advance...
Click to expand...
Click to collapse
Welcome to the forum
Perhaps you have not noticed this is an HTC devices only forum
However if you go to off topic section there is a trhead about samsung
Good luck,
p.d I recommend you to erase your pesonal data from your post
Related
Hey all. I used IMEI-CHECK to unlock a T-Mobile Dash I bought and now I am encountering some issues. I am using the phone on Cingular’s network. I have a Data package with them and for some reason cannot connect to the web from the phone. Also, when I ActiveSync, my contacts from OUTLOOK do not transfer over. I get an error message. I had a NOKIA E61 and all worked fine. I do not know why I am getting these error messages.
Also, under the COMM manager, the “Direct Push” and “Data Connection” options are grayed out and I cannot set up anything….
Please help. Do I need to rip the phone’s software off and re-install unlocked setting or what? How do I do it?
Thanks….
I don't think your issues are related to unlocking, backup everything and try a hard reset on the device and then try to activesync and setup your email account.
Did you change your settings?
You need to change your settings to work with cingular. Search this forum for the cingular wap/mms settings.
I hope starting a new thread is the way to go on this...
I just updated to the new Sprint Official WM 6.1 ROM, and immediately could not connect to the internet.
I tried running the IOTA automatic data provisioning update (Start->Settings->Personal Tab->Phone->Services Tab->Internet->Get Settings->Start) and it failed repeatedly with a 1012 error. As was posted by others, I noticed that there was a "CurrentUserName" setting in Start->Settings->System->Device Information that had [email protected] where I would have expected to see [email protected] instead. (that would have been my Sprint provided email address) The first thing I tried was to go to the phone dialpad and dial ##3282# to start the EPST program and check my data provisioning settings (this requires that you know your MSL - Master Service Lock Code - if you are going to edit). UserName was blank there, so I tapped the blank setting and held down until an "EDIT" menu popped up. I tapped "EDIT" and changed it to the previously correct [email protected] value. After saving changes and another reboot, I still could not connect to the internet, run IOTA, and the "CurrentUserName" was still wrong. After searching through various settings looking for a way to change the currentusername, I installed PHM Registry Editor and searched again.
In HKEY_LOCAL_MACHINE/Software/OEM/DIM there is a key "EnableCurrentUserName" and it was set to 1. I edited that and set it to 0, exited the Registry Editor, and restarted the device by holding the power button until it warned me about shutting down. I tapped "Yes" and it shut down and restarted. The "CurrentUserName" setting no longer appeared in the Device Information page. At this point I was able to run IOTA successfully and imediately after that I could use the internet and other data services.
I hope this helps someone. Sorry to be so long winded, but I was trying to answer as many "How? Where?" questions as I could as I went.
Briefly:
1. Using WM Registry Editor software, change HKLM/Software/OEM/DIM/"EnableCurrentUserName" from 1 to 0 then save changes and exit editor.
2. Dial ##3282# and edit UserName to correct [email protected] address. Device will reboot when you exit and save changes.
3. Run IOTA by going to Start->Settings->Personal Tab->Phone->Services Tab->Internet->Get Settings->Start
Thanks to all the others here who have helped me along the way,
Scruffy
anyone else know if this works?
i just flashed the new sprint rom and now the data connection does not work.. no internet.. ? I was just wondering if anyone else had this problem and does this fix it?
After some more time with this ROM installed I have found that it is not neccessary to change the ##DATA# (##3282#) user name settings. Just change the HKEY_LOCAL_MACHINE/Software/OEM/DIM/EnableCurrentUserName value to zero, save changes and then you can run the IOTA update successfully (or at least I can).
I have found that I need to do this every time I do a hard reset of my device. I hope this helps someone else.
Scruffy
this did not work for me.. I Get error code 67
i started a new thread here........ http://forum.xda-developers.com/showthread.php?t=415666
so maybe someone will chime in... the ##3282# does not work for me at all.. you hit that on the dial pad and nothing happens... so i can not access that menu...
For now i went back to a OEM rom and called sprint and they got me working by doing a MASTER RESET... also ##3282# works on OEM roms but i think the file EPST.EXE is missing from the CUSTOM roms... any input would be great..
Not working for me.
i'm sure a master reset from within #778 or whatever would work but i don't feel like
putting in the data again.
Scruffy said:
I hope starting a new thread is the way to go on this...
I just updated to the new Sprint Official WM 6.1 ROM, and immediately could not connect to the internet.
I tried running the IOTA automatic data provisioning update (Start->Settings->Personal Tab->Phone->Services Tab->Internet->Get Settings->Start) and it failed repeatedly with a 1012 error. As was posted by others, I noticed that there was a "CurrentUserName" setting in Start->Settings->System->Device Information that had [email protected] where I would have expected to see [email protected] instead. (that would have been my Sprint provided email address) The first thing I tried was to go to the phone dialpad and dial ##3282# to start the EPST program and check my data provisioning settings (this requires that you know your MSL - Master Service Lock Code - if you are going to edit). UserName was blank there, so I tapped the blank setting and held down until an "EDIT" menu popped up. I tapped "EDIT" and changed it to the previously correct [email protected] value. After saving changes and another reboot, I still could not connect to the internet, run IOTA, and the "CurrentUserName" was still wrong. After searching through various settings looking for a way to change the currentusername, I installed PHM Registry Editor and searched again.
In HKEY_LOCAL_MACHINE/Software/OEM/DIM there is a key "EnableCurrentUserName" and it was set to 1. I edited that and set it to 0, exited the Registry Editor, and restarted the device by holding the power button until it warned me about shutting down. I tapped "Yes" and it shut down and restarted. The "CurrentUserName" setting no longer appeared in the Device Information page. At this point I was able to run IOTA successfully and imediately after that I could use the internet and other data services.
I hope this helps someone. Sorry to be so long winded, but I was trying to answer as many "How? Where?" questions as I could as I went.
Briefly:
1. Using WM Registry Editor software, change HKLM/Software/OEM/DIM/"EnableCurrentUserName" from 1 to 0 then save changes and exit editor.
2. Dial ##3282# and edit UserName to correct [email protected] address. Device will reboot when you exit and save changes.
3. Run IOTA by going to Start->Settings->Personal Tab->Phone->Services Tab->Internet->Get Settings->Start
Thanks to all the others here who have helped me along the way,
Scruffy
Click to expand...
Click to collapse
how do i find [email protected] where would that be?
Scruffy said:
3. Run IOTA by going to Start->Settings->Personal Tab->Phone->Services Tab->Internet->Get Settings->Start
Click to expand...
Click to collapse
I just upgraded to NFSFAN's latest ROM, everything went well but I can not get my internet to work. The one thing I did notice is under the services tab, internet is not an option. I loaded the dcd sprint carrier 20090714 cab am I missing something else?
Thank you for any help you can provide.
Update:
Well I went back and flashed to the HTC 6.1 rom, then back to the 6.5 rom. That fixed my internet issues, but that option is still missing for me. Then after all of that my MSID was really screwed up. Everything seems to be good now.
please please help me clear the instructions
i have a horribly vague idea of what i need to do, to get the internet working again.
i already got the IOTA_1120 zip file in my cell but when i even try to open it up it says that there is no application that is related to to it, so i must start this application and open up the file from within. How do i do this? am I even doing what im supposed to??
Where exactly is HKEY_LOCAL_MACHINE/Software/OEM/DIM and how do i get there???
if you could please instruct me with simple stieps i would greatly appreciate it, simple being like start>program files> etc.
please help i am one step away from smashing this damm cell into the wall
electricfeel_2012 said:
i have a horribly vague idea of what i need to do, to get the internet working again.
i already got the IOTA_1120 zip file in my cell but when i even try to open it up it says that there is no application that is related to to it, so i must start this application and open up the file from within. How do i do this? am I even doing what im supposed to??
Where exactly is HKEY_LOCAL_MACHINE/Software/OEM/DIM and how do i get there???
if you could please instruct me with simple stieps i would greatly appreciate it, simple being like start>program files> etc.
please help i am one step away from smashing this damm cell into the wall
Click to expand...
Click to collapse
The path of HKEY.... is actually on the registry. You need to use a registry editor (like PHM Regedit) to make the necessary changes to the registry. I would recommend you to re-read those instructions as they will not get any easier than that. Alternatively, if you are on Sprint's official rom and have absolutely no clue what you are doing, you can always call them and ask them for help.
As far as the IOTA zip file, if you cannot open it, that means that you do not have any program to extract from compressed files in your device. Your best bet is to transfer the file to the desktop and extract it there. Once you are done, place the extracted contents back in the device and run it in there.
Earlier today I had a successful attempt at installing FXP's CM9 126 build. As a requirement I had to flash the R800x_4.0.2.E.57_Verizon.ftf via Flashtool to my phone before I could flash the Rom. My phone's provider is Cspire(formally Cellular South), and after the ftf my phone is trying to make contact with Verizon for activation, leaving my unable to call or text on my own provider. I've tried flashing a nand backup I had of one of Codename Andriod that I created when everything was working perfectly, but it didn't fix the problem.
Thank you for your time and please let me know what I can to fix this.
Sincerely,
Frag_Bag
Frag_Bag said:
Earlier today I had a successful attempt at installing FXP's CM9 126 build. As a requirement I had to flash the R800x_4.0.2.E.57_Verizon.ftf via Flashtool to my phone before I could flash the Rom. My phone's provider is Cspire(formally Cellular South), and after the ftf my phone is trying to make contact with Verizon for activation, leaving my unable to call or text on my own provider. I've tried flashing a nand backup I had of one of Codename Andriod that I created when everything was working perfectly, but it didn't fix the problem.
Thank you for your time and please let me know what I can to fix this.
Sincerely,
Frag_Bag
Click to expand...
Click to collapse
You'll need to change the build.prop and apn settings. Found this from a quick search with someone that has a working verizon build.prop that is said to work on cspire
https://www.dropbox.com/s/dgteu3ziweifix8/build.prop
and his working apn settings:
https://www.dropbox.com/s/6cs5tqwdlcstt3s/apns-conf.xml
Also found this:
You could push the apn with ADB but i just edited mine with root explorer in /System/etc and restarted the phone.
As for CDMA Workshop is a service software for CDMA phones it is used for flashing phones to different carriers to put it plain as possible in my mind but it can be used for countless useful tasks, just Google it to read more. But the below method was much easier.
Dialing ##7764726(##program) is used to manually program your phone.
After dialing ##7764726 press call it will prompt for a SPC password it should be 000000
Then click User Activation
MIN1 I put the last 7 digits of my phone number.
MIN2 put the first three of phone number(area code).
MDN is your 10 digit phone number.
CDMA Sys ID put 1996
IMSI_11_12 put 12
Then hit back and click on SID/NID Pairs:
SID_1: put 1996
NID_1: put 65535
After this hit back till you exit all the way back out of the menu the phone will reboot after it reboots i dialed *22801 it didn't say anything just sat at the activation screen for about 30sec. Then it said reprogramming the phone then rebooted agin after that i was back on C spire.
Links are a little old but this is all I could find:
SID Database if you need to find a different carrier
http://www.the-answerman.com/sidlist/index.asp
Also the SID/NID I used was found in this PRL breakdown:
http://www.howardforums.com/showthread.php/1700374-New-PRL-60575-50575
The Second post of the page explains a lot more about PRL and SID/NID just good to understand what your kinda messing with:
http://forum.xda-developers.com/showthread.php?p=19537266
Also i don't know if this is the best way to accomplish this task but it took me awhile to figure out this fix it worked for me but i can't guarantee anything also im not responsible if something goes wrong and you brick(its always possible) but i am willing to help to the best of my abilities
Good Luck and sorry for such a long post.
agraceful said:
You'll need to change the build.prop and apn settings. Found this from a quick search with someone that has a working verizon build.prop that is said to work on cspire
https://www.dropbox.com/s/dgteu3ziweifix8/build.prop
and his working apn settings:
https://www.dropbox.com/s/6cs5tqwdlcstt3s/apns-conf.xml
Also found this:
You could push the apn with ADB but i just edited mine with root explorer in /System/etc and restarted the phone.
As for CDMA Workshop is a service software for CDMA phones it is used for flashing phones to different carriers to put it plain as possible in my mind but it can be used for countless useful tasks, just Google it to read more. But the below method was much easier.
Dialing ##7764726(##program) is used to manually program your phone.
After dialing ##7764726 press call it will prompt for a SPC password it should be 000000
Then click User Activation
MIN1 I put the last 7 digits of my phone number.
MIN2 put the first three of phone number(area code).
MDN is your 10 digit phone number.
CDMA Sys ID put 1996
IMSI_11_12 put 12
Then hit back and click on SID/NID Pairs:
SID_1: put 1996
NID_1: put 65535
After this hit back till you exit all the way back out of the menu the phone will reboot after it reboots i dialed *22801 it didn't say anything just sat at the activation screen for about 30sec. Then it said reprogramming the phone then rebooted agin after that i was back on C spire.
Links are a little old but this is all I could find:
SID Database if you need to find a different carrier
http://www.the-answerman.com/sidlist/index.asp
Also the SID/NID I used was found in this PRL breakdown:
http://www.howardforums.com/showthread.php/1700374-New-PRL-60575-50575
The Second post of the page explains a lot more about PRL and SID/NID just good to understand what your kinda messing with:
http://forum.xda-developers.com/showthread.php?p=19537266
Also i don't know if this is the best way to accomplish this task but it took me awhile to figure out this fix it worked for me but i can't guarantee anything also im not responsible if something goes wrong and you brick(its always possible) but i am willing to help to the best of my abilities
Good Luck and sorry for such a long post.
Click to expand...
Click to collapse
I was able to enter all the values for MIN2, MDN, CDMA, and IMSI, but the MIN1 Keeps telling me "Unable to set new parameter, I made sure there was a 1 before my 7 digit number. Thoughts?
Frag_Bag said:
I was able to enter all the values for MIN2, MDN, CDMA, and IMSI, but the MIN1 Keeps telling me "Unable to set new parameter, I made sure there was a 1 before my 7 digit number. Thoughts?
Click to expand...
Click to collapse
I don't think you'll need the 1. Just the last 7 numbers. Try that to see if it works. And just so you know, I'm on verizon so all my answers are coming from google at the moment lol
I left the number the way it was and finished the steps, everything is working as it should and I can call and text. Thank you very much. Now i just have to find a fix for Mobile data. I really do appreciate it.
Frag_Bag said:
I left the number the way it was and finished the steps, everything is working as it should and I can call and text. Thank you very much. Now i just have to find a fix for Mobile data. I really do appreciate it.
Click to expand...
Click to collapse
Mobile data would be in the build.prop and the apn settings, You should be able to use pieces from the build.prop I posted to work whatever rom you're on. I got to assume verizon and cspire are close to identical since they're both cdma. Half way there right?
agraceful said:
Mobile data would be in the build.prop and the apn settings, You should be able to use pieces from the build.prop I posted to work whatever rom you're on. I got to assume verizon and cspire are close to identical since they're both cdma. Half way there right?
Click to expand...
Click to collapse
Are these settings still current cspire settings... I lost 3g connectivity and would love to troubleshoot to figure out whats wrong with it... I did the ##Program and here are my settings
USER ACTIVATION MENU
MIN-my number with area code
IMSI_11_12 =23
MDN - my number with area code
CDMA system ID - 1996
EXTENDED NAM MENU
MIN = another local number
TRUE IMSI - 000000000007809
IMSI_11_12 = 23
MDN - my number with area code
CDMA system ID - 1996
Country code - 311
CDMA network - 65535
1st channel A - 283
1st channel B - 384
2nd channel A - 691
2nd channel B - 777
Access overload class 0
URGENT
im having the same issue when i use ##program and dail it does nothing but act like a collect call HELP
on cm9
Thanks...
agraceful said:
You'll need to change the build.prop and apn settings. Found this from a quick search with someone that has a working verizon build.prop that is said to work on cspire
https://www.dropbox.com/s/dgteu3ziweifix8/build.prop
and his working apn settings:
https://www.dropbox.com/s/6cs5tqwdlcstt3s/apns-conf.xml
Also found this:
You could push the apn with ADB but i just edited mine with root explorer in /System/etc and restarted the phone.
As for CDMA Workshop is a service software for CDMA phones it is used for flashing phones to different carriers to put it plain as possible in my mind but it can be used for countless useful tasks, just Google it to read more. But the below method was much easier.
Dialing ##7764726(##program) is used to manually program your phone.
After dialing ##7764726 press call it will prompt for a SPC password it should be 000000
Then click User Activation
MIN1 I put the last 7 digits of my phone number.
MIN2 put the first three of phone number(area code).
MDN is your 10 digit phone number.
CDMA Sys ID put 1996
IMSI_11_12 put 12
Then hit back and click on SID/NID Pairs:
SID_1: put 1996
NID_1: put 65535
After this hit back till you exit all the way back out of the menu the phone will reboot after it reboots i dialed *22801 it didn't say anything just sat at the activation screen for about 30sec. Then it said reprogramming the phone then rebooted agin after that i was back on C spire.
Links are a little old but this is all I could find:
SID Database if you need to find a different carrier
http://www.the-answerman.com/sidlist/index.asp
Also the SID/NID I used was found in this PRL breakdown:
http://www.howardforums.com/showthread.php/1700374-New-PRL-60575-50575
The Second post of the page explains a lot more about PRL and SID/NID just good to understand what your kinda messing with:
http://forum.xda-developers.com/showthread.php?p=19537266
Also i don't know if this is the best way to accomplish this task but it took me awhile to figure out this fix it worked for me but i can't guarantee anything also im not responsible if something goes wrong and you brick(its always possible) but i am willing to help to the best of my abilities
Good Luck and sorry for such a long post.
Click to expand...
Click to collapse
Thanks for copying and pasting all this from my thread you could have atleast acknowledged me since it's basically word for word
http://forum.xda-developers.com/showthread.php?t=1624990
I hope this is the right place to post this.
When I had my EVO 4g I installed P-Droid, but either I don't remember how I did it, or the method for installing it has changed. So how exactly do I get it installed on my SGS3? I tried using the P-Droid autopatcher on my ROM AOKP JB 10.11.2012b. It said it completed but it never placed the two flashable zips in its directory.
Is this ROM not compatible or am I doing something wrong? I would love to keep P-Droid working again. Would be cool if there was a ROM with it already built into it.
yahar said:
I hope this is the right place to post this.
When I had my EVO 4g I installed P-Droid, but either I don't remember how I did it, or the method for installing it has changed. So how exactly do I get it installed on my SGS3? I tried using the P-Droid autopatcher on my ROM AOKP JB 10.11.2012b. It said it completed but it never placed the two flashable zips in its directory.
Is this ROM not compatible or am I doing something wrong? I would love to keep P-Droid working again. Would be cool if there was a ROM with it already built into it.
Click to expand...
Click to collapse
What is p-droid?
Sent from my SPH-L710...if some one helps you press the thanks button
xtrezpasor said:
What is p-droid?
Sent from my SPH-L710...if some one helps you press the thanks button
Click to expand...
Click to collapse
PDroid allows blocking access for any installed application to the following data separately:
Device ID (IMEI/MEID/ESN)
Subscriber ID (IMSI)
SIM serial (ICCID)
Phone and mailbox number
Incoming call number
Outgoing call number
GPS location
Network location
List of accounts (including your google e-mail address)
Account auth tokens
Contacts
Call logs
Calendar
SMS
MMS
Browser bookmarks and history
System logs
SIM info (operator, country)
Network info (operator, country)
For device ID, phone and mailbox number, SIM serial, subscriber ID and device location it also allows supplying custom or random values.
http://forum.xda-developers.com/showthread.php?t=1357056
I tried reading through it all but I am still confused a bit. I think it can be only used on dedoxed roms (first i've heard of dedoxed). I am unsure if its the rom itself I am supposed to patch or something else. I tried asking elsewhere but got no answer.
yahar said:
PDroid allows blocking access for any installed application to the following data separately:
Device ID (IMEI/MEID/ESN)
Subscriber ID (IMSI)
SIM serial (ICCID)
Phone and mailbox number
Incoming call number
Outgoing call number
GPS location
Network location
List of accounts (including your google e-mail address)
Account auth tokens
Contacts
Call logs
Calendar
SMS
MMS
Browser bookmarks and history
System logs
SIM info (operator, country)
Network info (operator, country)
For device ID, phone and mailbox number, SIM serial, subscriber ID and device location it also allows supplying custom or random values.
http://forum.xda-developers.com/showthread.php?t=1357056
I tried reading through it all but I am still confused a bit. I think it can be only used on dedoxed roms (first i've heard of dedoxed). I am unsure if its the rom itself I am supposed to patch or something else. I tried asking elsewhere but got no answer.
Click to expand...
Click to collapse
So if you just read the first post like i did you would of clearly seen that it only works with gingerbread... No ics version
Sent from my SPH-L710...if some one helps you press the thanks button
---------- Post added at 03:51 AM ---------- Previous post was at 03:49 AM ----------
I will however take a look when i get home from my trip to see if i can figure out how to get it to work
Sent from my SPH-L710...if some one helps you press the thanks button
Here you go PDroid Extension that's the latest information I'm aware..
Best of luck
After logging in with either Waterfox or Chromium when I go to User Profile/User Details. It says:
"Our records show that you have already registered under the name of aileronster. If you have lost your password, click here. If you would like to modify your profile, click here."
Clicking the "Modify profile" just takes me back to the same message. Also I was having problems with Authenticate Email address didn't work and was giving the same message above I believe. So I waited a day to see if I would get a confirmation email with no luck
I've been reading for days on how to root/backup an LG K8 (2018) X210ULMG which doesn't seem to have proper support. So I have a long road ahead of me to figure out exactly how to create a custom TWRP, root the thing, RIP the ORIGINAL image off the phone (NOT Something similar.) So I need to be able to ask questions and get clarifications. So would really like to be able to make sure the whole site works for me, as I think I'm going to be hacking/researching this (hopefully carefully) for a while before I'm successful.