So I'm having problems installing Hard SPL (Olinex Unsigned). The phone is connected w/ Active-sync to my computer, and all of those required "steps" to check before you begin flashing were there. It takes just a few seconds for the HardSPL to install, and it says "congratulations...", so I assumed it went well. However, when it boots up, it says NOTHING about Olinex. Instead, when I'm on the boot screen, it has red letters, the lower ones stating my normal ROM build. It looks like:
R 1.00.25.5
G 1.52.29.25.12H
D 1.93 ...
I assume this is the bootloader? I held the lower volume button and hit the soft reset button to get to the bootloader, and that was the same screen it went to. However, then the ROM boots up on the phone, and it's the same intro screen as my initial ROM was. When I proceed with trying to install the HardSPL again, it tells me my current ROM is 1.93.401.2.. not Olinex.' I also tried the SSPLmanual file. No good..
Also, I realized that when I ask for it to update, Mobile Device Center loses connection w/ my phone. Maybe I am just having a problem holding a connection between the two? Activesync is turned on on my phone, and Mobile Device Center says that my phone is connected before the flash.
Has anyone had this problem before, or know how I can fix it? Thanks everyone. I've been looking around everywhere.
TAhsifter88 said:
So I'm having problems installing Hard SPL (Olinex Unsigned). The phone is connected w/ Active-sync to my computer, and all of those required "steps" to check before you begin flashing were there. It takes just a few seconds for the HardSPL to install, and it says "congratulations...", so I assumed it went well. However, when it boots up, it says NOTHING about Olinex. Instead, when I'm on the boot screen, it has red letters, the lower ones stating my normal ROM build. It looks like:
R 1.00.25.5
G 1.52.29.25.12H
D 1.93 ...
I assume this is the bootloader? I held the lower volume button and hit the soft reset button to get to the bootloader, and that was the same screen it went to. However, then the ROM boots up on the phone, and it's the same intro screen as my initial ROM was. When I proceed with trying to install the HardSPL again, it tells me my current ROM is 1.93.401.2.. not Olinex.' I also tried the SSPLmanual file. No good..
Also, I realized that when I ask for it to update, Mobile Device Center loses connection w/ my phone. Maybe I am just having a problem holding a connection between the two? Activesync is turned on on my phone, and Mobile Device Center says that my phone is connected before the flash.
Has anyone had this problem before, or know how I can fix it? Thanks everyone. I've been looking around everywhere.
Click to expand...
Click to collapse
I'm under the impression that you are not entering your bootloader screen. Please try this again (soft reset and ASAP, press the vol down button). Keep holding it until you see Red, Green, etc.(rainbow like coloured screen) .... please report back what it says on that screen before we move on.
wow.. I suppose that did the trick. AND it DOES say that it has Olinex on it, so I guess that installed w/o a problem! Thank, I really appreciate the help. Unfortunately, I've heard many different ways to get there (mainly hold vol-down THEN press soft-reset).
One last question though.. Now that I spent a good 30 minutes installing the list of those tweaks, would I really see much of an improvement jumping to a cooked ROM? I was looking at getting AZTOR or Nataly's lite (I'm not asking which one..), but I am not sure how much of an improvement I'm looking at. I'm currently running the stock ROM as 1.93 (I guess I'm running Olinex atm). Now that I've applied all of those tweaks from that one page, is it worth it to jump to a cooked ROM?
Thanks again! That makes my day seem MUCH more successful now.
TAhsifter88 said:
wow.. I suppose that did the trick. AND it DOES say that it has Olinex on it, so I guess that installed w/o a problem! Thank, I really appreciate the help. Unfortunately, I've heard many different ways to get there (mainly hold vol-down THEN press soft-reset).
One last question though.. Now that I spent a good 30 minutes installing the list of those tweaks, would I really see much of an improvement jumping to a cooked ROM? I was looking at getting AZTOR or Nataly's lite (I'm not asking which one..), but I am not sure how much of an improvement I'm looking at. I'm currently running the stock ROM as 1.93 (I guess I'm running Olinex atm). Now that I've applied all of those tweaks from that one page, is it worth it to jump to a cooked ROM?
Thanks again! That makes my day seem MUCH more successful now.
Click to expand...
Click to collapse
Hi I would not to back to a stock 1.93 rom even the stock 2.03 rom is a lot better in my option.
cobbs said:
Hi I would not to back to a stock 1.93 rom even the stock 2.03 rom is a lot better in my option.
Click to expand...
Click to collapse
haha, so you recommend I go ahead and push my luck w/ a 2.03 cooked ROM? Will I really have to worry about all of those tweaks, or will they already be optimized in the cooked roms? Again, I'm looking at 2 that are based off of performance, so I can expect they'll already be well-tweaked, but I'm new w/ all of this.
TAhsifter88 said:
haha, so you recommend I go ahead and push my luck w/ a 2.03 cooked ROM? Will I really have to worry about all of those tweaks, or will they already be optimized in the cooked roms? Again, I'm looking at 2 that are based off of performance, so I can expect they'll already be well-tweaked, but I'm new w/ all of this.
Click to expand...
Click to collapse
Hi I would but thats me. yes these roms are tweaked for performance.
make sure you have read this http://forum.xda-developers.com/showthread.php?t=416211
warning once you start to flash some roms it is hard to stop.
Hi have a look here to flash from the internal storage.
http://forum.xda-developers.com/showpost.php?p=3287426&postcount=10
Lately I keep like 4 cooked roms in folder on my internal storage and when I feel the need to try a new rom I just copy it to root, change name and install OS from bootloader (volDown, backButton, resetButton).
That is my identical process. Sometimes they never make it to the flashing stage but always a couple on standby...lol
Related
Hi all,
I want to downgrade to 6.1 again after having 6.5 for about 2 days.
I'm experiencing audio issues, which I had before, I sent it to the service-center and it worked like a charm again.
So all I wan't to know is if it's possible to just download the official ROM from HTC.com and use theire RUU to downgrade. I'm a nooooob but I managed to install 6.5 pretty easily. But I don't know what hardSPL does etc. So i'm not totally sure if it's possible. Can anyone help with this. Having abolutely no audio is pretty anoying. Also searched the forum but found nothing usefull, allmost everybody comes to the conclusion that it's a hardware issue. Which is strange because why do I experience this after installing 6.5 and when I used 6.1 it worked.
Thanks in advance
Daan
Load from htc officel website new htc rom and flash of your diamond
when not funktion you cann extraxt the exe.file withe winrar and rename the nb file to diamimg.nbh and take this to root of your diamond hd and make soft reset and audio(-)and reback after push to on/off buttong
syr for my english im türkish and speck germen its inuf
DaanJordaan said:
Hi all,
I want to downgrade to 6.1 again after having 6.5 for about 2 days.
I'm experiencing audio issues, which I had before, I sent it to the service-center and it worked like a charm again.
So all I wan't to know is if it's possible to just download the official ROM from HTC.com and use theire RUU to downgrade. I'm a nooooob but I managed to install 6.5 pretty easily. But I don't know what hardSPL does etc. So i'm not totally sure if it's possible. Can anyone help with this. Having abolutely no audio is pretty anoying. Also searched the forum but found nothing usefull, allmost everybody comes to the conclusion that it's a hardware issue. Which is strange because why do I experience this after installing 6.5 and when I used 6.1 it worked.
Thanks in advance
Daan
Click to expand...
Click to collapse
Ok, let me try. I guess someone will correct me if I'm wrong with what I say
First HardSPL won't let you flash original rom directly. It will block SPL flashing, to avoid relocking or messing up the phone. So, regarding your problem, I would first try to flash a 6.1 cooked rom to make sure that the problem is hardware, not software.
If it's hardware, here is what I did when I had to return my phone:
- First, "cook" an official rom: you have to extract nbh, take only os.nb, rebuild the nbh, flash it.
- Eventually, flash the official radio if you tried alternative radio, same goes for logo.
- After that, your mobile should be almost like official, the only remaining "suspect" is the HardSPL. You have to flash back one of the stock SPL provided here: http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39. It has to be done at the end, when everything else is back to stock.
Don't have much time right now to give more details, let me know if you need more...
Thanks a lot man i'm at work right know but i'll try it out as soon as i get home
thanks again
Daan
Just got home from work.
Like you said, I need to know if the problem is HW or SW since i've experienced this problem before, maybe it overheated or something I don't know. Anyhoo I flashed radio 1.11.25.01 and it seems to work fine now. But the funny thing is that when I flashed it with 6.5 there were no problems at all but after about 15 hours or so when I tried to put on some music... Silence!!! F***. So I hope this won't just repeat itself endlessly.
The reason why I tried flashing the radio first is that I kinda like 6.5. But well, if it's going to happen again i'll use your method.
Thanks for the reply, I'll keep you posted if anything weird happens
Daan
DaanJordaan said:
Just got home from work.
Like you said, I need to know if the problem is HW or SW since i've experienced this problem before, maybe it overheated or something I don't know. Anyhoo I flashed radio 1.11.25.01 and it seems to work fine now. But the funny thing is that when I flashed it with 6.5 there were no problems at all but after about 15 hours or so when I tried to put on some music... Silence!!! F***. So I hope this won't just repeat itself endlessly.
The reason why I tried flashing the radio first is that I kinda like 6.5. But well, if it's going to happen again i'll use your method.
Thanks for the reply, I'll keep you posted if anything weird happens
Daan
Click to expand...
Click to collapse
Strange. Yes, it could be overheating Or, maybe a radio crash ? If it happens again, you should try to remove the battery, wait a few seconds and put it back again.
Crossing fingers for you
The sun is Shining!
Well the audio is still working, I'm draining the battery to check if it's maybe a power problem, but so far I still have sound and my battery is down to two bars in the windows mobile power meter (not in the menu bar)
So I really hope radio 1.11.25.01 fixed my problem
I hope this is my last post on this thread and if it isn't, we'll just have to dig further
Thanks very much,
Daan
letama said:
Ok, let me try. I guess someone will correct me if I'm wrong with what I say
First HardSPL won't let you flash original rom directly. It will block SPL flashing, to avoid relocking or messing up the phone. So, regarding your problem, I would first try to flash a 6.1 cooked rom to make sure that the problem is hardware, not software.
If it's hardware, here is what I did when I had to return my phone:
- First, "cook" an official rom: you have to extract nbh, take only os.nb, rebuild the nbh, flash it.
- Eventually, flash the official radio if you tried alternative radio, same goes for logo.
- After that, your mobile should be almost like official, the only remaining "suspect" is the HardSPL. You have to flash back one of the stock SPL provided here: http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39. It has to be done at the end, when everything else is back to stock.
Don't have much time right now to give more details, let me know if you need more...
Click to expand...
Click to collapse
Look in my signature for the config of my diamond. I have had no problems whatsoever flashing an original HTC stock ROM from the HTC website. I just use the executable downloaded from HTC.
henk2484 said:
Look in my signature for the config of my diamond. I have had no problems whatsoever flashing an original HTC stock ROM from the HTC website. I just use the executable downloaded from HTC.
Click to expand...
Click to collapse
Thanks, but i'm sticking to 6.5 I flashed a different radio it's working fine right now, but the battery is draining a little bit faster, but i can live with that.
thanks for the info i'll keep it in mind when i decide to switch back to 6.1
Daan
bandit999 said:
Load from htc officel website new htc rom and flash of your diamond
when not funktion you cann extraxt the exe.file withe winrar and rename the nb file to diamimg.nbh and take this to root of your diamond hd and make soft reset and audio(-)and reback after push to on/off buttong
syr for my english im türkish and speck germen its inuf
Click to expand...
Click to collapse
walla aslanım ben hiç bir şey anlamadım..özür dilerim
Ok, so I am a Newb, but I am a start guy... 153 IQ, was always top of my class - however I have no F**ng clue what the guys in the development and hacking section are talking about.
Basically, I have a TP2 for Tmobile that I would like to do something with... ANYTHING~! Preferable install a cooked WM6.5 rom, or a 6.1 rom with Manilla 2.5 for the time being. An android or Sense UI port would be nice as well.
Can someone please either help me get started by pointing my in the correct direction of a helpful sticky, because frankly its tough searching through threads like this:
"[JUL 13][APP][ALPHA4] Nitrogen 1.1 (music player for Windows Mobile)"
Any help would be appreciated by me, and other not so technically inclined individuals.
Thanks a ton!
http://thewingster.com/default.aspx they have a pic guide on how to install a cooked rom and also provide you with the rom
lilchip85 said:
http://thewingster.com/default.aspx they have a pic guide on how to install a cooked rom and also provide you with the rom
Click to expand...
Click to collapse
Guys like you Rock!
llllllllll said:
Guys like you Rock!
Click to expand...
Click to collapse
lol thanks. also click on my sig for softwares. it's always being updated with new apps that you might like for your tp2
lilchip85 said:
lol thanks. also click on my sig for softwares. it's always being updated with new apps that you might like for your tp2
Click to expand...
Click to collapse
Thanks, I checked out the ROM u use and it looks smooth, but I want Manilla
http://forum.xda-developers.com/showthread.php?t=560320
Im trying to mess with this one here. The .exe install sounds simple - but any pointers to doing this?
Also, I dont sync my contacts with Outlook - is there a preferred way to back them up otherwise?
llllllllll said:
Ok, so I am a Newb, but I am a start guy... 153 IQ, was always top of my class - however I have no F**ng clue what the guys in the development and hacking section are talking about.
Basically, I have a TP2 for Tmobile that I would like to do something with... ANYTHING~! Preferable install a cooked WM6.5 rom, or a 6.1 rom with Manilla 2.5 for the time being. An android or Sense UI port would be nice as well.
Can someone please either help me get started by pointing my in the correct direction of a helpful sticky, because frankly its tough searching through threads like this:
"[JUL 13][APP][ALPHA4] Nitrogen 1.1 (music player for Windows Mobile)"
Any help would be appreciated by me, and other not so technically inclined individuals.
Thanks a ton!
Click to expand...
Click to collapse
Welcome to forums
This is the official XDA how to flash for noobs:
http://forum.xda-developers.com/showthread.php?t=550540
Read, Search, Respect and Enjoy!
Good luck,
Will the Tom Rhodium Manilla -> http://forum.xda-developers.com/showthread.php?t=560320 Work in landscape mode?
llllllllll said:
Will the Tom Rhodium Manilla -> http://forum.xda-developers.com/showthread.php?t=560320 Work in landscape mode?
Click to expand...
Click to collapse
i don't think it will but it won't hurt to test it out. i hate not having landscape but i seem to be getting used to it.
hmm.. I think the energy rom should... ill give it a shot, worst case, i can just reflash to stock 6.1 right?
Im stuck at this part LOL
http://thewingster.com/howtohspltp2.aspx
Cant install active sync on vista
I tried running the hardspl, but it completed in 10 sec and all it did was restrart my phone
It´s better to try the Wiki instructions as they are backed up by a lot of members
Activesync is for XP computers only!!
For Vista or S7ven use Windows Mobile Device center
llllllllll said:
Im stuck at this part LOL
http://thewingster.com/howtohspltp2.aspx
Cant install active sync on vista
I tried running the hardspl, but it completed in 10 sec and all it did was restrart my phone
Click to expand...
Click to collapse
i had the windows mobile device center running and it said my phone was connected. plug in the usb and put active sync on the device and the wmd will show your phone is connected. i was confused also since it said active sync failed.
as for the hardspl
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it) and verify the screen shows 0.85.OliNex, which is the HardSPL version*
orb3000 said:
It´s better to try the Wiki instructions as they are backed up by a lot of members
Activesync is for XP computers only!!
For Vista or S7ven use Windows Mobile Device center
Click to expand...
Click to collapse
what he said
lilchip85 said:
i
as for the hardspl
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it) and verify the screen shows 0.85.OliNex, which is the HardSPL version*
Click to expand...
Click to collapse
How exactly do I do a soft reset? What else do I hold down aside from the volume down key?
llllllllll said:
How exactly do I do a soft reset? What else do I hold down aside from the volume down key?
Click to expand...
Click to collapse
(if you have tmobile it's the lil circular slot on the right) just power off your device when you turn it on just hold the volume down
I did that and its already showing SPL - ).85.01 olinex
I didnt think the process worked as it said it takes 10 min, and it took about 6 seconds.
Is this all i needed to do and can i start the rom flash now?
llllllllll said:
I did that and its already showing SPL - ).85.01 olinex
I didnt think the process worked as it said it takes 10 min, and it took about 6 seconds.
Is this all i needed to do and can i start the rom flash now?
Click to expand...
Click to collapse
it says 10 mins but it doesn't take that long. now you can flash away. i've flashed my phone like 3 times and ended with the touch it rom. i never tried tom codon rom. if you do try and landscape works let me know!
also you only need to hardspl once. so if you get tired of the rom just plug it in. run the customruu.exe and flash the new rom but ofcourse follow the instructions on the site lol
Hi All,
Wonder anyone could built new ROM for ACer E100? Original ROM was having problems, Comm Manager always error.
Regards,
Calvin Lee
calvinljh said:
Hi All,
Wonder anyone could built new ROM for ACer E100? Original ROM was having problems, Comm Manager always error.
Regards,
Calvin Lee
Click to expand...
Click to collapse
You can use E101 Rom and soon will be updated
Edit: Try from this link http://hidemyass.com/files/xv4GF/ it is a 28008 build.
To flash just copy on Sdcard and rename it as flash.bin, during reset keep volume up pressed it start sd card update.
frrfba said:
You can use E101 Rom and soon will be updated
Edit: Try from this link http://hidemyass.com/files/xv4GF/ it is a 28008 build.
To flash just copy on Sdcard and rename it as flash.bin, during reset keep volume up pressed it start sd card update.
Click to expand...
Click to collapse
Hi Frrfba, Thanks bro, wonder you have original file for me to download, as a backup. incase anything happend.
Yea we have.. go ahead and flash
calvinljh said:
Hi Frrfba, Thanks bro, wonder you have original file for me to download, as a backup. incase anything happend.
Click to expand...
Click to collapse
hdubli said:
Yea we have.. go ahead and flash
Click to expand...
Click to collapse
Hi Hdubli, can I have download link please,
http://hidemyass.com/files/xv4GF/ there you can download build 28008 for E100.
The flash for me was alright. Some notes though: the setup of Windows isn't working 100%, it seems to freeze at some point and a dropdownbox wasn't clearly shown. Also, the screen isn't used 100%: pixels at the side aren't used. Also, there seems to be a margin for the letters, as some letters at the edge (still in the active area though) seem to fall off.
edit: seems like something went wrong. I get the top bar showing the icons, but the yellow/orange Windows logo doesn't disappear. Have to do a hard reset I guess.
edit2: did a hard reset and this time I disconnected the phone from computer. Everything worked fine now, except that the outside pixels (about 5 on each side) are still not used. But the dropdownboxes all showed alright and it booted alright and installed extrom alright . Sry for the confusion, very good job on the ROM! Will test some more .
TheEvilVirus said:
http://hidemyass.com/files/xv4GF/ there you can download build 28008 for E100.
The flash for me was alright. Some notes though: the setup of Windows isn't working 100%, it seems to freeze at some point and a dropdownbox wasn't clearly shown. Also, the screen isn't used 100%: pixels at the side aren't used. Also, there seems to be a margin for the letters, as some letters at the edge (still in the active area though) seem to fall off.
edit: seems like something went wrong. I get the top bar showing the icons, but the yellow/orange Windows logo doesn't disappear. Have to do a hard reset I guess.
edit2: did a hard reset and this time I disconnected the phone from computer. Everything worked fine now, except that the outside pixels (about 5 on each side) are still not used. But the dropdownboxes all showed alright and it booted alright and installed extrom alright . Sry for the confusion, very good job on the ROM! Will test some more .
Click to expand...
Click to collapse
To correctly have a good "start" after first rebbot, keep pda disconnetcted from everything.
After calibrate screen, extrom install all the cabs in the rom and after reboot it works good everything.
Keep in kind that the rom is tested (in italian) for 3 weeks withou any problems, let us know if need help.
ciao
Everything works fine for me too now. Thank you for the ROM, great job. Love the new build, it's much finger friendlier!
hdubli said:
Yea we have.. go ahead and flash
Click to expand...
Click to collapse
bro, can upload original e100 rom ? pls help
Hmm there is a problem with ActiveSync: the device doesn't always want to connect. The computer says it is not connected, but the device says it is. After some time or after trying to disconnect, the device just freezes. Annoying .
edit:.
Man hate this. It's really the device, tried 3 computers and they all refuse the connection. They say connecting and then disconnected, while the device thinks it's connected. Really odd, as it worked flawlessly before! Did a clean install and still not working!
TheEvilVirus said:
Hmm there is a problem with ActiveSync: the device doesn't always want to connect. The computer says it is not connected, but the device says it is. After some time or after trying to disconnect, the device just freezes. Annoying .
edit:.
Man hate this. It's really the device, tried 3 computers and they all refuse the connection. They say connecting and then disconnected, while the device thinks it's connected. Really odd, as it worked flawlessly before! Did a clean install and still not working!
Click to expand...
Click to collapse
Bro, this is bug issue, never flash your ROM before you ensure you get your original WWE ROM as default.....
Most importan part, no one is response when my first post, and "they" always told to "flash it, any problem is advise". <--- this part is very funny.
Not sure what you mean calvin, but anyway I reflashed with this custom ROM and it works again. No clue what changed, as a clean boot didn't help. But I'm happy again. And in case something happens, I still have the original ROM so not much risk for me.
edit: ooh no not again. After the first night, it was screwed again. Can't connect anymore :S. Hmm maybe I should go back to default then
TheEvilVirus said:
Not sure what you mean calvin, but anyway I reflashed with this custom ROM and it works again. No clue what changed, as a clean boot didn't help. But I'm happy again. And in case something happens, I still have the original ROM so not much risk for me.
edit: ooh no not again. After the first night, it was screwed again. Can't connect anymore :S. Hmm maybe I should go back to default then
Click to expand...
Click to collapse
Are You using Xp, Vista or else?
Can You check if ActiveSYnc is disconnected when screen goes black (timeout on backlight)? Don't let that Windows Mobile adjust backlight but set it!
In my case never found this kind of problem, but I see in various forum that 6.5 build in some case goes with this problem, for example I got that situation with Vista and with original rom 21840 build.
Apologies for the slightly off topic post, but I don't suppose you guys know of any updated ROMs for the beTouch E200 do you? Would like to get an updated version of WM6.5 on this thing...
The problem is that the computer (tried both Vista and Windows 7) doesn’t connect, while the device says it is connected. Then nothing happens, except that the device freezes after some time or says that any program I want to run isn’t a valid PPC application :S. After a reset everything is fine again, except that I can’t use activesync. This both happens with USB and Bluetooth connection. The connection is also lost when I power off the phone manually. But that rarely happens: it always freezes before I even get to that point and then it doesn’t respond to anything.
Also, when I unplug the device before it freezes, I get an ARM error saying I need to go to some specific memory address or ARM will break. If I go to that address, the phone freezes with screen off, if I let the ARM break (what the...?!) it freezes with screen on .
I just flashed back to original ROM. The first sync is alright. If it stays alright, then definitely the custom ROM can be 'blamed'. If no further is heard, then everything is fine again with original ROM.
TheEvilVirus said:
The problem is that the computer (tried both Vista and Windows 7) doesn’t connect, while the device says it is connected. Then nothing happens, except that the device freezes after some time or says that any program I want to run isn’t a valid PPC application :S. After a reset everything is fine again, except that I can’t use activesync. This both happens with USB and Bluetooth connection. The connection is also lost when I power off the phone manually. But that rarely happens: it always freezes before I even get to that point and then it doesn’t respond to anything.
Also, when I unplug the device before it freezes, I get an ARM error saying I need to go to some specific memory address or ARM will break. If I go to that address, the phone freezes with screen off, if I let the ARM break (what the...?!) it freezes with screen on .
I just flashed back to original ROM. The first sync is alright. If it stays alright, then definitely the custom ROM can be 'blamed'. If no further is heard, then everything is fine again with original ROM.
Click to expand...
Click to collapse
Hi TheEvilVirus, can I know where you download the original WWE ROM?, I need as my backup too. thanks thanks.
I'm sorry, can't give you the location . But if you might need it, maybe something can be arranged .
TheEvilVirus said:
I'm sorry, can't give you the location . But if you might need it, maybe something can be arranged .
Click to expand...
Click to collapse
Hi, may I know what does it mean? How can it be arranged? as in?
Just PM Me .
TheEvilVirus said:
Just PM Me .
Click to expand...
Click to collapse
Hi, may I know what does it mean? How can it be arranged? as in?
I got my Vogue late 2008 and unlocked it and have had many different ROMs on it. Until recently, I was running NFSFAN's 6.5 v1 ROM. I *cough* got mad at my phone because it was not responding and pushed hard on the screen *cough*. Happens to everyone right ? Anyway, now the screen is all white with a bunch of lines on the left, Verizon is shipping me a new one. Problem, or not, is I told them I had no thrid-party apps on it, which I do, and I have unlocked it and put a custom ROM on it, illegal w/ Verizon right? Can I factory reset or something to get WinMo 6.1 back on it so they don't get mad if indeed they can get it working? Note the screen does not work at all.
EnterpriseNX01 said:
I got my Vogue late 2008 and unlocked it and have had many different ROMs on it. Until recently, I was running NFSFAN's 6.5 v1 ROM. I *cough* got mad at my phone because it was not responding and pushed hard on the screen *cough*. Happens to everyone right ? Anyway, now the screen is all white with a bunch of lines on the left, Verizon is shipping me a new one. Problem, or not, is I told them I had no thrid-party apps on it, which I do, and I have unlocked it and put a custom ROM on it, illegal w/ Verizon right? Can I factory reset or something to get WinMo 6.1 back on it so they don't get mad if indeed they can get it working? Note the screen does not work at all.
Click to expand...
Click to collapse
You should be able to just put it into bootloader (by pushing power,camera, and soft reset button) and then flash your stock verizon 6.1 rom. That would erase all your apps and put it back to how it was when you bought it. Though it would still show that you have the phone unlocked with imcokeman in your bootloader..
You can't drop the phone because that would show cracks.
You can't make it wet because that's detectable.
Most people forget, this is an electronic device and there is 1 easy fix.
Put a big magnet... I mean BIG magnet next to it for about a minute or two.
No visible/obvious damage
But that sucker will definitely be wiped
Barogi44 said:
You should be able to just put it into bootloader (by pushing power,camera, and soft reset button) and then flash your stock verizon 6.1 rom. That would erase all your apps and put it back to how it was when you bought it. Though it would still show that you have the phone unlocked with imcokeman in your bootloader..
Click to expand...
Click to collapse
To add a few things to what Barogi is saying...
You can flash back the device to WM 6.1 stock from Verizon. Flashing another rom is not illegal, but it does void the warranty since you need to hardSPL to do that. So, even if you did take it back to stock, you have the issue of relocking.... (not really an issue, but..)
Do as Barogi suggested and make sure you hard reset the device after you flashed (just in case any programs survived the flash). After you are done, simply download this and run it. That's it, problem solved...
Good luck!
egzthunder1 said:
To add a few things to what Barogi is saying...
You can flash back the device to WM 6.1 stock from Verizon. Flashing another rom is not illegal, but it does void the warranty since you need to hardSPL to do that. So, even if you did take it back to stock, you have the issue of relocking.... (not really an issue, but..)
Do as Barogi suggested and make sure you hard reset the device after you flashed (just in case any programs survived the flash). After you are done, simply download this and run it. That's it, problem solved...
Good luck!
Click to expand...
Click to collapse
just to let you know it seems your link is broken.
Barogi44 said:
just to let you know it seems your link is broken.
Click to expand...
Click to collapse
Ahhhgggrrr! Why are all my links coming down? Damn it! I think I have it at home, I will upload it later....
Thanks barogi! I can always count on you
egzthunder1 said:
Ahhhgggrrr! Why are all my links coming down? Damn it! I think I have it at home, I will upload it later....
Thanks barogi! I can always count on you
Click to expand...
Click to collapse
haha welcome!
HI im having some very big problems with my tilt2. I can teather it fine but for some reason after a day or two i get the remote party has ended the connection, and no matter what i do to it, weather it be uninstall the script and speed patch and reinstall it, it wont help. so i have to format the phone and load it all over again and it works fine for about 2 days tops. Anyone have any ideas why this is happening? I seem to be formatting this phone every 2 days just to get it to teather.
i had the same thing happen to my kaiser with the stock att rom what i did was flash the rom and radio. after that problem was gone never happened again. you can also try this http://forum.xda-developers.com/showthread.php?t=538874
i don't know if this is of any help to you. After you get the error message can you still connect with active sync?
nope
after the errormessage i cant connect on the internet at all, i have to formatt the phone and reload everything to get it to work again
Rom and radio
What rom and radio do you reccomend for the tilt2 thats stable
i remember getting that error on my blackjack, it was mostly because i let it idle and data disconnects when not in use. its not like its a stable connection. if you wanted that you buy the crappy little usb card.
tomfubarr said:
What rom and radio do you reccomend for the tilt2 thats stable
Click to expand...
Click to collapse
the rom i'm using right now is here http://forum.xda-developers.com/showthread.php?t=617142
and Radio 4.49.25.91 i found the link on the same page.
if you're new to flashing i suggest you go here first http://forum.xda-developers.com/showthread.php?t=550540 it helped me out alot
Possible solution
The above mentioned "idle" problem is more than likely your culprit. I had a similar problem as well with the stock ROM. I suggest using NRG's Leo ROM to fix this problem. There are other solutions, but they are pretty tech savvy ones. Plus, if you haven't flashed your ROM yet, dude, you don't know what you're missing. The whole reason we're here is to push our phone's to the limit as far as functionality is concerned. Stock ROM's don't even cut it. Give a new one a whirl, I promise you won't be disappointed, plus, your reformatting issue will be gone as well, just a heads up from someone who's been around, you know?
Stuck
OK i try to update rom and im stuck on 0% of the hard spl prog and wont do nothing then errors out
tomfubarr said:
OK i try to update rom and im stuck on 0% of the hard spl prog and wont do nothing then errors out
Click to expand...
Click to collapse
Is your phone "unlocked?"
tomfubarr said:
OK i try to update rom and im stuck on 0% of the hard spl prog and wont do nothing then errors out
Click to expand...
Click to collapse
For the Tilt2 you'll want to use the enablerapinew.cab file in the Hard SPL thread.